Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MELTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

A molecular dynamics study of melting and dissociation of tungsten nanoparticles

Molecular dynamics simulations were conducted to study the melting and dissociation of free tungsten nanoparticles. For the various interatomic potentials applied, the melting points of the tungsten nanoparticles increased with increasing nanoparticle diameter. Combining these results with the melting point of bulk tungsten in the experiment, the melting point of nanoparticles with diameters ranging from 4 to 12 nm could be determined. As the temperature increases, free nanoparticles are subject to dissociation phenomena. The dissociation rate was observed to follow Arrhenius behavior, and the Meyer–Neldel rule was obeyed. These results are useful in understanding the behavior of tungsten dust generated in nuclear fusion devices as well as for the preparation, formation, and application of tungsten powders.

36 MATERIALS SCIENCE↗

Ab-initio calculations on melting of thorium

Ab-initio molecular dynamics study has been performed on face centered cubic structured thorium to determine its melting temperature at room pressure. The ion-electron interaction potential energy calculated as a function of temperature for three volumes (a{sub 0}){sup 3} and (1.02a{sub 0}){sup 3} and (1.04a{sub 0}){sup 3} increases gradually with temperature and undergoes a sharp jump at ~2200 K, ~2100 K and ~1800 K, respectively. Here, a{sub 0} = 5.043 Å is the equilibrium lattice parameter at 0 K obtained from ab-initio calculations. These jumps in interaction energy are treated as due to the onset of melting and corresponding temperatures as melting point. The melting point of 2100 K is close to the experimental value of 2023 K. Further, the same has been verified by plotting the atomic arrangement evolved at various temperatures and corresponding pair correlation functions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Advanced Modeling of Cold Crucible Induction Melting for Process Control and Optimization

The Idaho National Laboratory (INL) and the St. Petersburg Electrotechnical University “LETI” (ETU) have collaborated on development and validation of an advanced numerical model of the cold crucible induction melting (CCIM) process. This work was conducted in support of the Department of Energy (DOE) Office of Environmental Management Technology and Engineering (EM-20) International Program. The model predicts quasi-steady state temperature distributions, convection cell configurations, and flow field velocities for a fully established melt of low conductivity non-magnetic materials at high frequency operations. The INL/ETU ANSYS© finite element model is unique in that it has been developed specifically for processing borosilicate glass (BSG) and other glass melts. Specifically, it accounts for the temperature dependency of key material properties, some of which change by orders of magnitude within the temperature ranges experienced (temperature differences of 500oC are common) in CCIM processing of glass, including density, viscosity, thermal conductivity, specific heat, and electrical resistivity. These values, and their responses to temperature changes, are keys to understanding the melt characteristics. Because the model has been validated, it provides the capability to conduct parametric studies to understand operational sensitivities and geometry effects. Additionally, the model can be used to indirectly determine difficult to measure material properties at higher temperatures such as resistivity, thermal conductivity and emissivity. The model can also be used to optimize system design and to predict operational behavior for specific materials and system configurations, allowing automated feedback control. This becomes particularly important when designing melter systems for full-scale industrial applications.

42 ENGINEERING↗

Ultrasonic Acoustic Velocities During Partial Melting of a Mantle Peridotite KLB-1

Knowledge of the elastic properties of partially molten rocks is crucial for understanding low-velocity regions in the interior of the Earth. Models of fluid and solid mixtures have demonstrated that significant decreases in seismic velocity are possible with small amounts of melt, but there is very little available data for testing these models, particularly with both P and S waves for mantle compositions. We report ultrasonic measurements of P and S velocities on a partially molten KLB-1 sample at mantle conditions using a multi-anvil device at a synchrotron facility. The P, S, and bulk sound velocities decrease as melting occurs. We find that the quantity, ∂lnV S /∂lnV B (where V B is the bulk sound velocity) is lower than mechanical models estimate. Instead, our data, as well as previous data in the literature, are consistent with a dynamic melting model in which melting and solidification interact with the stress field of the acoustic wave.

58 GEOSCIENCES↗

Laser‐Powder Melt Pool Solidification Dynamics and Microstructural Engineering of Ti‐5553 Microlattices

The fine geometric and topological control afforded by additive manufacturing technologies has enabled the manufacture of architected materials across length scales, and enabling tunable mechanical performance as a function of local and global design. Progress has been made to tune the mechanical response of architected materials through geometry, but understanding how the geometry and processing conditions will inform the microstructure remains a challenge due to the rapid solidification in laser powder bed fusion. This study uses in situ X-ray imaging and electron backscatter diffraction microscopy to demonstrate that the melt pool size, microstructure morphology, and elastic strain distribution is influenced by a combination of lattice geometry and laser processing conditions. These results indicate that within larger melt pools the local thermal gradients are sufficient to enable a columnar-to-equiaxed transition across the melt pool. Furthermore, the solidification mechanisms producing these microstructures are examined across the first 5 ms of melting and solidification, described via in situ high-speed X-ray imaging and mirrored via multiphysics simulation.

additive manufacturing↗

Distinct Melt Infusion Architectures of Antiperovskite Solid Electrolytes

Antiperovskite solid electrolytes are an emerging class of lithium‐ion conductors distinguished by their unusually low melting points, enabling scalable, low‐temperature processing routes not accessible to most solid electrolytes. In this work, we synthesize phase‐pure chloride (Cl), bromide (Br), and mixed halide (ClBr) variants of antiperovskites and investigate their ionic conductivities in both powder and hot‐pressed forms. Hot pressing significantly enhances conductivity across all compositions, while energy‐dispersive X‐ray spectroscopy (EDS) of the mixed halide system reveals halide surface migration during densification. We further investigate the melt‐infiltration behavior of these electrolytes into substrates relevant to solid‐state battery architectures, including Al and Cu current collectors, conventional NMC and LFP cathodes, and a foamed NMC cathode with a highly porous architecture. The foamed cathode enables deep and uniform electrolyte penetration, highlighting the role of electrode architecture in facilitating melt infiltration. Across all substrates, electrolyte halide chemistry strongly influences wetting behavior, penetration depth, and resulting microstructural morphology. Together, these results establish clear processing–structure relationships for melt‐infiltrated antiperovskite solid electrolytes and demonstrate how electrolyte chemistry and electrode architecture govern interfacial morphology during integration, providing practical guidelines for processing and structural design in solid‐state battery systems.

antiperovskite↗

Predicting Melt Curves of Energetic Materials Using Molecular Models

Here, in this work, the solid–liquid coexistence curves of classical fully flexible atomistic models of α-RDX and β-HMX were calculated using thermodynamically rigorous methodologies that identify where the free energy difference between the phases is zero. The free energy difference between each phase at a given state point was computed using the pseudosupercritical path (PSCP) method, and Gibbs–Helmholtz integration was used to evaluate the solid–liquid free energy difference as a function of temperature. This procedure was repeated for several pressures to determine points along the coexistence curve, which were then fit to the Simon–Glatzel functional form. While effective, this method is computationally expensive. An alternative approach is to compute the melting point at a single pressure via the PSCP method, and then use the Gibbs–Duhem integration technique to trace out the coexistence curve in a more computationally economical manner. Both approaches were used to determine the coexistence curve of α-RDX. The Gibbs–Duhem integration method was shown to generate a melt curve that is in good agreement with the PSCP-derived melt curve, while only costing ~10 % of the computational resources used for the PSCP method. For α-RDX, the predicted melting temperature increases significantly more for a given increase in pressure when compared to available experimental data.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Separation of Non-metallic Inclusions from a Fe-Al-O Melt Using a Super-Gravity Field

An innovative method for separating non-metallic inclusions from a high temperature melt using super gravity was systematically investigated. To explore the separation behavior of inclusion particles with densities less than that of metal liquid under a super-gravity field, a Fe-Al-O melt containing Al{sub 2}O{sub 3} particles was treated with different gravity coefficients. Al{sub 2}O{sub 3} particles migrated rapidly towards the reverse direction of the super gravity and gathered in the upper region of the sample. It was hard to find any inclusion particles with sizes greater than 2 μm in the middle and bottom areas. Additionally, the oxygen content in the middle region of the sample could be reduced to 0.0022 mass pct and the maximum removal rate of the oxygen content reached 61.4 pct. The convection in the melt along the direction of the super gravity was not generated by the super-gravity field, and the fluid velocity in the molten melt consisted only of the rotating tangential velocity. Moreover, the motion behavior of the Al{sub 2}O{sub 3} particles was approximatively determined by Stokes’ law along the direction of super gravity.

36 MATERIALS SCIENCE↗

Numerical Simulation of Metal Melt Flow in a One-Strand Tundish Regarding Active Filtration and Reactive Cleaning

In the paper, two different cleaning strategies for nonmetallic inclusions in steel melts, active filtration and reactive cleaning, are examined in a prototype tundish configuration. In active filtration, nonmetallic inclusions are deposited at the filter surfaces. In reactive cleaning, nonmetallic inclusions stick to the filter surfaces, too. In addition, they are floated by the action of carbon monoxide bubbles, which are generated by reaction between carbon and oxygen in the steel melt. In order to compare the performance of both strategies, numerical simulations of the two-phase flows of steel melt and dispersed nonmetallic inclusions are performed. Turbulence is resolved with implicit large eddy simulation. If necessary, species transports of dissolved carbon in the melt and reaction with oxygen are employed. Cleaning efficiencies are deduced from the simulations which demonstrate that reactive cleaning is much more efficient than active filtration.

36 MATERIALS SCIENCE↗

Numerical Analysis of Molten Pool Behavior and Spatter Formation with Evaporation During Selective Laser Melting of 316L Stainless Steel

During the selective laser-melting process, material evaporation and resultant spatter are common phenomena that bring about many defects. However, the underlying physical phenomena such as molten pool behavior and spatter formation, as evaporation occurred, are sparsely understood and difficult to observe during the process. Thus, a three–dimensional powder-scale model was established to investigate the thermal and flow behavior of the molten pool, the morphology evolution of the molten pool and keyhole, and the spatter formation with evaporation in the selective laser-melting processing of 316L stainless steel. Phase transitions and variations in interfacial force were taken into account in this model. The modified phase-field method was applied to trace the melt–gas interface. The results showed that keyhole formed in molten pool under recoil pressure, and that there were some differences in the temperature distribution and flow behavior inside and outside the keyhole. In addition, the dimension and surface morphology of the molten pool and keyhole depth altered and gradually stabilized during the process. Moreover, droplet spatter formation at rear of molten pool proceeded roughly as follows: the backward ejection of melt vapor would induce a depression in molten pool and a bump on the molten pool surface, the bump moved backward and subsequently a liquid column formed, then the liquid column formed a neck and gradually pinched off, resulting in the droplet spatter. Furthermore, the characteristic morphology of the scan track and dimension of the molten pool were obtained through experiments, which showed good agreement with the simulation results.

36 MATERIALS SCIENCE↗

Microstructure, Mechanical Properties and Residual Stress of Selective Laser Melted AlSi10Mg

AlSi10Mg processed by selective laser melting (SLM) is common in various industries because of its complex structure and high performance. The microstructure, residual stress and mechanical properties restrict its application, while they are affected by the scanning path type and preheating temperature. In this work, to investigate the properties of selective laser melted AlSi10Mg alloys and gain better performance results, the microstructure and mechanical tests are performed at several preheating temperatures based on the uniformity and chessboard scanning strategy. It is found that the selective laser melted AlSi10Mg parts fabricated in the chessboard scanning path have better mechanical properties than those fabricated in the uniformity scanning path. Furthermore, a higher preheating temperature can induce less residual stress due to the enhanced Al crystal faces. Finally, analyses of the microstructures, mechanical and residual stress provide a valuable suggestion that the combination of the range of preheating temperature and the scanning path can improve the performance of selective laser melted AlSi10Mg.

36 MATERIALS SCIENCE↗

Nanoscale interfacial melting enables bonding during high velocity microparticle impacts

Melting during high-velocity particle impact has been understood to be typically detrimental to bonding by lowering the strength at the interface and promoting rebound before solidification can occur. Here we establish a possible remedy to this challenge: by dramatically restricting the volume of molten material, its resolidification is accelerated, effectively forming a nanoscale, braze-type joint during impact. In-situ single particle impact imaging is combined with post-mortem structural and chemical analyses to reveal a regime where adhesion is governed not by extensive plastic deformation, but by the kinetics of melt layer resolidification. Furthermore, these findings redefine the role of melting in impact-based processes, establishing transient melting and rapid solidification as a viable strategy for engineering successful adhesion events.

Additive manufacturing↗

Detecting missing struts in metallic micro-lattices using high speed melt pool thermal monitoring

Metal lattices are an important class of cellular materials that offer great advantages by providing high-strength and lightweight structures as compared to bulk materials. Progress in additive manufacturing techniques has led to increased complexity in design and shape of produced objects and is greatly beneficial for the development of metallic lattice structures. However additive manufacturing of lattices suffers from unpredictable defect creation that can compromise its mechanical integrity. Although post-build inspection techniques can provide quality assurance of the process, accurate assessment can be technically challenging, time consuming and costly. In this work, we investigate the use of high-speed measurements of thermal emission from the melt pool to identify defective individual struts formed with a missing bottom half in an otherwise fully built lattice structure produced with laser powder bed fusion. Surprisingly, results indicate lower photodiode signal, suggesting colder melt pool surface temperature, when printing struts with missing bottom half as compared to nominal struts. Additional thermographic imaging and multi-physics simulations reveal that the low photodiode signal is accompanied by presence of hot spatters carrying heat away from detection and continuous avalanche of powder on the melt pool. Based on these observations, a method was developed to identify defective individual struts with missing bottom half in full built lattices. This prediction approach provides valuable insights about part quality which are important for process qualification and illustrates the utility of melt pool thermal emission monitoring for identifying specific defects introduced by laser powder bed fusion.

36 MATERIALS SCIENCE↗

Synthesis of precipitation-strengthened Al-Sc, Al-Zr and Al-Sc-Zr alloys via selective laser melting of elemental powder blends

Selective laser melting is used to create Al-1.5Sc, Al-1.5Zr and Al-0.75Sc-0.75Zr (at.%) alloys from blends of elemental Al, Sc, and Zr powders. This study investigates elemental alloying elements (Sc and Zr) which are high-melting and highly reactive, unlike previous work which focused on more concentrated elemental additions of lower-melting, lower-reactivity Cu and Si to aluminum. High-speed in situ synchrotron x-ray imaging and diffraction show that the 20–30 μm Al, Sc, and Zr powders fully melt and sufficiently mix in the molten state to create, on solidification, a homogeneous distribution of primary, micron-size L12 precipitates (Al 3 Sc, Al 3 Zr, and Al 3 (Sc,Zr), respectively) and nucleate micron-size Al matrix grains, as confirmed by SEM imaging of cross-sections. Here, a second laser pass, simulating a realistic additive-manufacturing build condition, fully remelts the initial volume which shows, after solidification, the same Al 3 (Sc,Zr) L1 2 primary micro-precipitates and very fine Al grains. After aging at 300–400°C, the alloys show large increases in hardness, consistent with an exceptionally high number density (1.4 × 10 24 m –3 ) and volume fraction (2.5%) of secondary Al 3 (Sc,Zr) nano-precipitates with a Sc-rich core and Zr-rich shell, as measured via atom-probe tomography.

36 MATERIALS SCIENCE↗

Cookoff experiments of a melt cast explosive (Comp-B3)

Validated models of melt cast explosives exposed to accidental fires are essential for safety analysis. In the current work, we provide several experiments that can be used to develop and validate cookoff models of melt cast explosives such as Comp-B3 composed of 60:40 wt% RDX:TNT. We present several vented and sealed experiments from 2.5 mg to 4.2 kg of Comp-B3 in several configurations. We measured pressure, spatial temperature, and ignition time. Some experiments included borescope images obtained during both vented and sealed decomposition. We observed the TNT melt, the suspension of RDX particles in the melt, bubble formation caused by RDX decomposition, and bubble-induced mixing of the suspension. The RDX suspension did not completely dissolve, even as temperatures approached ignition. Our results contrast with published measurements of RDX solubility in hot TNT that suggest RDX would be completely dissolved at these high temperatures. These different observations are attributed to sample purity. We did not observe significant movement of the two-phase mixture until decomposition gases formed bubbles. Bubble generation was inhibited in our sealed experiments and suppressed mixing.

42 ENGINEERING↗

Dendrite-resolved, full-melt-pool phase-field simulations to reveal non-steady-state effects and to test an approximate model

In this report we study the epitaxial, columnar growth of (multiply oriented) dendrites/cells for a spot melt in a polycrystalline Al–Cu substrate using two-dimensional, phase-field, direct numerical simulations (DNS) at the full-melt-pool scale. Our main objective is to compare the expensive DNS model to a much cheaper but approximate “line” model in which a single-crystal phase-field simulation is confined to a narrow rectangular geometry. To perform this comparison, we develop algorithms that automatically extract quantities of interest (QoIs) from both DNS and line models. These QoIs allow us to quantitatively assess the assumptions in the line model and help us analyze its discrepancy with the DNS model. We consider four sets of heat source parameters, mimicking welding and additive manufacturing conditions, that create a combination shallow and deep melt pools. Our largest DNS simulation used 16K x 14K grid points in space. Our main findings can be summarized as follows. Under AM conditions, the QoIs of line models are in excellent agreement with the full DNS results for both shallow and deep melt pools. Under welding conditions, the primary spacing of the DNS model is smaller than the prediction of line model. We identify a geometric crowding effect that accounts for the discrepancies between the DNS and line models. We propose two potential mechanisms that determine the response of the microstructure to geometric crowding.

36 MATERIALS SCIENCE↗

Formation and Morphology of "shish-like" Fibril Crystals of Aliphatic Polyesters from the Sheared Melt

We found the formation of 'shish-like' fibril crystals of aliphatic polyesters such as poly(L-lactic acid) (PLLA), poly({var_epsilon}-caprolactone) (PCL), poly(12-hydroxydodecanoic acid) (PHDA) and poly(16-hydroxyhexadecanoic acid) (PHHA) from the sheared melt with shear rate {gamma} = 5 s{sup -1} observed by polarizing optical microscope (POM). The melting temperature T{sub m}s of obtained fibril crystals of PLLA and PCL were higher than those of spherulites and were close to the equilibrium melting temperature T{sub m}{sup 0}. The small angle X-ray scattering (SAXS) patterns from the bulk sample including fibril crystals, small amount of unoriented small crystals and amorphous showed no peaks arose from the existence of long periods in fibril crystals. These are the evidence that the observed fibril crystals consist of assemblies of a lot of extended chain crystals (ECCs). We observed the morphology of moderately extracted single strand of fibril crystals at the magnification of POM by means of scanning electron microscope. We found that macroscopic fibril crystals of PLLA with diameter d = 10 {micro}m consist of the bundle structure of microscopic fibril crystals with d = 2 {micro}m. From POM observation of the formation of fibril crystals of PLLA and PCL, we showed phase diagrams of molecular weight M and crystallization temperature T{sub c} for the formation of fibril crystals. From these phase diagrams, we evaluated a critical M and T{sub c} for the formation of fibril crystals. Moreover, from the sequential melting and crystallization experiments, it was implied that the entanglement and transesterification play an important role on the formation of fibril crystals of aliphatic polyesters.

36 MATERIALS SCIENCE↗

Effect of laser rescanning on the grain microstructure of a selective laser melted Al-Mg-Zr alloy

Highlights: • Laser rescanning of a new Al-Mg-Zr alloy was investigated. • SLM of the Al-Mg-Zr alloy results in a duplex grain structure. • Rescanning of the alloy results in a refinement of the microstructure. - Abstract: The microstructures of alloys created via Additive Manufacturing (AM) can vary substantially from those present in cast or wrought products, due to the very rapid solidification associated with AM. While numerous studies have investigated the process-microstructure relationship of alloys created by Selective Laser Melting (SLM), few have investigated the effects of laser rescanning to alter the microstructure or take advantage of the rapid solidification conditions the process provides. This study investigates the effect of single- or multiple pass laser scanning upon the grain structure of Addalloy™, a new Al-Mg-Zr alloy strengthened via L1{sub 2} Al{sub 3}Zr precipitates. The bottom of the melt pools consisted of fine equiaxed grains (1.3 μm) that nucleated from primary Al{sub 3}Zr (100–400 nm) precipitates. The top of the melt pool consists of columnar grains (up to 40 μm long), consistent with lack of Al{sub 3}Zr nucleants due to Zr solute trapping from increased solidification velocities. Additional laser scanning (a second or third scan) reduces the amounts of columnar grains and increased the number equiaxed grains. The change is attributed to a shallower melt pool remelting the columnar grain region upon rescanning, due to reduced laser energy absorption and increased heat losses in the solid.

36 MATERIALS SCIENCE↗