Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Single-beam ion source enhanced growth of transparent conductive thin films

A single-beam ion source was developed and used in combination with magnetron sputtering to modulate the film microstructure. The ion source emits a single beam of ions that interact with the deposited film and simultaneously enhances the magnetron discharge. The magnetron voltage can be adjusted over a wide range, from approximately 240 to 130 V, as the voltage of the ion source varies from 0 to 150 V, while the magnetron current increases accordingly. The low-voltage high-current magnetron discharge enables a 'soft sputtering mode', which is beneficial for thin-film growth. Indium tin oxide (ITO) thin films were deposited at room temperature using a combined single-beam ion source and magnetron sputtering. Furthermore, the ion beam resulted in the formation of polycrystalline ITO thin films with significantly reduced resistivity and surface roughness. Single-beam ion-source-enhanced magnetron sputtering has many potential applications in which low-temperature growth of thin films is required, such as coatings for organic solar cells.

36 MATERIALS SCIENCE↗

Plasma sputtering robotic device for in-situ thick coatings of long, small diameter vacuum tubes

A novel robotic plasma magnetron mole with a 50 cm long cathode was designed, fabricated, and operated. The reason for this endeavor is to alleviate the problems of unacceptable resistive heating of stainless steel vacuum tubes in the BNL Relativistic Heavy Ion Collider (RHIC). The magnetron mole was successfully operated to copper coat an assembly containing a full-size, stainless steel, cold bore, RHIC magnet tubing connected to two types of RHIC bellows, to which two additional pipes made of RHIC tubing were connected. To increase the cathode lifetime, a movable magnet package was developed, and the thickest possible cathode was made, with a rather challenging target to substrate (de facto anode) distance of less than 1.5 cm. Achieving reliable steady state magnetron discharges at such a short cathode to anode gap was rather challenging, when compared to commercial coating equipment, where the target to substrate distance is 10's cm; 6.3 cm is the lowest experimental target to substrate distance found in the literature. Additionally, the magnetron developed during this project provides unique omni-directional uniform coating. The magnetron is mounted on a carriage with spring loaded wheels that successfully crossed bellows and adjusted for variations in vacuum tube diameter, while keeping the magnetron centered. Electrical power and cooling water were fed through a cable bundle. The umbilical cabling system is driven by a motorized spool. Excellent coating adhesion was achieved. Measurements indicated that well-scrubbed copper coating reduced secondary electron yield to 1, i.e., the problem of electron clouds can be eliminated. Room temperature RF resistivity measurement indicated that a 10 μm copper coated stainless steel RHIC tube has a conductivity close to that of pure copper tubing. Excellent coating adhesion was achieved. The device details and experimental results are described.

36 MATERIALS SCIENCE↗

Investigation of ISIS and Brookhaven National Laboratory ion source electrodes after extended operation

Linac4 accelerator of Centre Europeen de Recherches Nucleaires is under construction and a RF-driven H{sup -} ion source is being developed. The beam current requirement for Linac4 is very challenging: 80 mA must be provided. Cesiated plasma discharge ion sources such as Penning or magnetron sources are also potential candidates. Accelerator ion sources must achieve typical reliability figures of 95% and above. Investigating and understanding the underlying mechanisms involved with source failure or ageing is critical when selecting the ion source technology. Plasma discharge driven surface ion sources rely on molybdenum cathodes. Deformation of the cathode surfaces is visible after extended operation periods. A metallurgical investigation of an ISIS ion source is presented. The origin of the deformation is twofold: Molybdenum sputtering by cesium ions digs few tenths of mm cavities while a growth of molybdenum is observed in the immediate vicinity. The molybdenum growth under hydrogen atmosphere is hard and loosely bound to the bulk. It is, therefore, likely to peel off and be transported within the plasma volume. The observation of the cathode, anode, and extraction electrodes of the magnetron source operated at BNL for two years are presented. A beam simulation of H{sup -}, electrons, and Cs{sup -} ions was performed with the IBSimu code package to qualitatively explain the observations. This paper describes the operation conditions of the ion sources and discusses the metallurgical analysis and beam simulation results.

08 HYDROGEN↗

CdSxTe1-x Alloying in CdS/CdTe Solar Cells

A CdSxTe1-x layer forms by interdiffusion of CdS and CdTe during the fabrication of thin-film CdTe photovoltaic (PV) devices. The CdSxTe1-x layer is thought to be important because it relieves strain at the CdS/CdTe interface that would otherwise exist due to the 10% lattice mismatch between these two materials. Our previous work [1] has indicated that the electrical junction is located in thisinterdiffused CdSxTe1-x region. Further understanding, however, is essential to predict the role of this CdSxTe1-x layer in the operation of CdS/CdTe devices. In this study, CdSxTe1-x alloy films were deposited by RF magnetron sputtering and co-evaporation from CdTe and CdS sources. Both radio-frequency-magnetron-sputtered and co-evaporated CdSxTe1-x films of lower S content (x<0.3) have a cubiczincblende (ZB) structure akin to CdTe, while those of higher S content have a hexagonal wurtzite (WZ) structure like that of CdS. Films become less preferentially oriented as a result of a CdCl2 heat treatment at~400 degrees C for 5 min. Films sputtered in a 1% O2/Ar ambient are amorphous as deposited, but show CdTe ZB, CdS WZ, and CdTe oxide phases after a CdCl2 heat treatment (HT). Filmssputtered in O2 partial pressure have a much wider bandgap (BG) than expected. This may be explained by nanocrystalline size effects seen previously [2] for sputtered oxygenated CdS (CdS:O) films.

14 SOLAR ENERGY↗

Optimization of sputtering NiOx films for perovskite solar cell applications

Highlights: • NiO{sub x} HTLs were fabricated by three kinds of magnetron sputtering techniques. • Chemical composition, lattice strain and energy levels of NiO{sub x} films were studied and compared. • PSCs based on sputtered NiO{sub x} HTL achieved highest PCE of 16.3% with negligible hysteresis. • Compared with PEDOT:PSS HTL, PSCs based on NiO{sub x} HTL exhibited enhanced stability in air. - Abstract: In this work, we systematically investigated the properties of three kinds of NiO{sub x} films prepared by magnetron sputtering either NiO or Ni target under direct current (DC) or radio frequency (RF) power without any preheating. Those NiO{sub x} films were found to be different in composition ratios, lattice strain and energy levels, thus showing different optical and carrier transport properties. By RF power source, sputtering Ni target in pure O{sub 2} atmosphere led to NiO{sub x} film with relatively good crystallization and surface properties compared with other two types of NiO{sub x} films. These NiO{sub x} films were further introduced into CH{sub 3}NH{sub 3}PbI{sub 3} based planar p-i-n heterojunction perovskite solar cells (PSCs) as the hole transport layers (HTL). It is revealed that PSCs based on NiO{sub x} HTL prepared by sputtering Ni target in pure O{sub 2} atmosphere achieved a highest power conversion efficiency of 16.3% with negligible hysteresis. Compared with devices with PEDOT:PSS HTL, PSCs based on magnetron sputtered NiO{sub x} HTL presented substantially improved stability in air. The results provide theoretical and experimental guidance on selecting NiO{sub x} HTLs fabricated by magnetron sputtering techniques.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Stability of Brillouin flow in the presence of slow-wave structure

Including a slow-wave structure (SWS) on the anode in the conventional, planar, and inverted magnetron, we systematically study the linear stability of Brillouin flow, which is the prevalent flow in crossed-field devices. The analytic treatment is fully relativistic and fully electromagnetic, and it incorporates the equilibrium density profile, flow profile, and electric field and magnetic field profiles in the linear stability analysis. Using parameters similar to the University of Michigan's recirculating planar magnetron, the numerical data show that the resonant interaction of the vacuum circuit mode and the corresponding smooth-bore diocotron-like mode is the dominant cause for instability. This resonant interaction is far more important than the intrinsic negative (positive) mass property of electrons in the inverted (conventional) magnetron geometry. It is absent in either the smooth-bore magnetron or under the electrostatic assumption, one or both of which was almost always adopted in prior analytical formulation. This resonant interaction severely restricts the wavenumber for instability to the narrow range in which the cold tube frequency of the SWS is within a few percent of the corresponding smooth bore diocotron-like mode in the Brillouin flow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The FNAL injector upgrade

The present FNAL H{sup -} injector has been operational since the 1970s and consists of two magnetron H{sup -} sources and two 750 keV Cockcroft-Walton Accelerators. In the upgrade, both slit-type magnetron sources will be replaced with circular aperture sources, and the Cockcroft-Waltons with a 200 MHz RFQ (radio frequency quadrupole). Operational experience at BNL (Brookhaven National Laboratory) has shown that the upgraded source and RFQ will be more reliable, improve beam quality and require less manpower than the present system. The present FNAL (Fermi National Accelerator Laboratory) injector has been operational since 1978 and has been a reliable source of H{sup -} beams for the Fermilab program. At present there are two Cockcroft-Walton injectors, each with a magnetron H{sup -} source with a slit aperture. With these two sources in operation, the injector has a reliability of better than 97%. However, issues with maintenance, equipment obsolescence, increased beam quality demands and retirement of critical personnel, have made it more difficult for the continued reliable running of the H{sup -} injector. The recent past has also seen an increase in both downtime and source output issues. With these problems coming to the forefront, a new 750 keV injector is being built to replace the present system. The new system will be similar to the one at BNL (Brookhaven National Laboratory) that has a similar magnetron source with a round aperture and a 200MHz RFQ. This combination has been shown to operate extremely reliably.

43 PARTICLE ACCELERATORS↗

Studies on hard TaN thin film deposition by R C-Mag technique

The physical and mechanical properties of pulsed rotating cylindrical magnetron sputter-grown tantalum nitride (TaN) thin films were studied. Initially, films were grown at ambient substrate temperature by varying the reactive (N{sub 2}) to sputter (Ar) gas ratio (R) at a constant pulsing frequency of the target power (100 kHz). The results were compared with planar magnetron-grown TaN samples. The R C-Mag. grown thin films have properties nearly similar to the high temperature (300 degree sign C) dc planar magnetron sputter deposited samples. In comparison to the planar magnetron deposition, the progression of the phase composition occurs over a wider range of R in the pulsed R C-Mag. deposition. These observed differences for R C-Mag. deposition are attributed to the increased glancing angle deposition of adatoms and pulsing of the target power. To study the effect of pulsing frequency of the target power in R C-Mag., the films were also grown at different frequencies at a fixed R (0.1). With the increase in frequency, the mechanical hardness increased up to 50 kHz and started decreasing beyond 50 kHz. The observed changes in the mechanical hardness are attributed to the increase in stress and to the formation of increased polycrystalline understoichiometric TaN phases.

36 MATERIALS SCIENCE↗

Novel techniques and devices for in-situ film coatings of long, small diameter tubes or elliptical and other surface contours

In this study, devices and techniques that can, via physical vapor deposition,coat various surface contours or very long small aperture pipes, are described. Recently, a magnetron mole was developed in order to in-situ coat accelerator tube sections of the Brookhaven National Lab relativistic heavy ion collider that have 7.1 cm diameter with access points that are 500 m apart, for copper coat the accelerator vacuum tube in order to alleviate the problems of unacceptable ohmic heating and of electron clouds. A magnetron with a 50 cm long cathode was designed fabricated and successfully operated to copper coat a whole assembly containing a full-size, stainless steel, cold bore, of the accelerator magnet tubing connected to two types bellows, to which two additional pipes made of accelerator tubing were connected. The magnetron is mounted on a carriage with spring loaded wheels that successfully crossed bellows and adjusted for variations in vacuum tube diameter, while keeping the magnetron centered. Electrical power and cooling water were fed through a cable bundle. The umbilical cabling system, which is enclosed in a flexible braided metal sleeve, is driven by a motorized spool. To increase cathode lifetime, movable magnet package was developed, and thickest possible cathode was made, with a rather challenging target to substrate distance of less than 1.5 cm. Optimized process to ensure excellent adhesion was developed. Coating thickness of 10 μm Cu passed all industrial tests and even exceeded maximum capability of a 12 kg pull test fixture. Room temperature radio frequency (RF) resistivity measurement indicated that 10 μm Cu coated stainless steel accelerator tube has conductivity close to copper tubing. Work is in progress to repeat the RF resistivity measurement at cryogenic temperatures. Over 20 years ago, a device using multi axis robotic manipulators controlling separate robotic assemblies resulted in nine-axes of motion combined with conformal shape of the cathodes that can adapt to various curved surface contours was developed and successfully used for depositing optical coating on aircraft canopies. The techniques can be utilized for in situ coating of elliptical and other surface contour RF cavities and long beam pipes with thick superconducting films. Plans are to incorporate ion assisted deposition in those techniques for attaining dense, adherent and defect free coatings.

43 PARTICLE ACCELERATORS↗

In-situ sputtering apparatus

A sputtering apparatus that includes at least a target presented as an inner surface of a confinement structure, the inner surface of the confinement structure is preferably an internal wall of a circular tube. A cathode is disposed adjacent the internal wall of the circular tube. The cathode preferably provides a hollow core, within which a magnetron is disposed. Preferably, an actuator is attached to the magnetron, wherein a position of the magnetron within the hollow core is altered upon activation of the actuator. Additionally, a carriage supporting the cathode and communicating with the target is preferably provided, and a cable bundle interacting with the cathode and linked to a cable bundle take up mechanism provided power and coolant to the cathode, magnetron, actuator and an anode of the sputtering apparatus.

42 ENGINEERING↗

Electrochemical properties of Li[Li{sub 0.2}Mn{sub 0.54}Co{sub 0.13}Ni{sub 0.13}]O{sub 2} cathode thin film by RF sputtering for all-solid-state lithium battery

The Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} thin films were prepared by radio frequency magnetron sputtering on Pt/Ti/SiO{sub 2}/Si substrate with target contained a 5% excess of lithium precursor. Thin films were deposited under various deposition conditions such as working pressure, gas ratio of Ar and O{sub 2}, and the temperature of in-situ annealing treatment. The thin films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The electrochemical property was estimated by a WBC3000 cycler with Li|Li[Li{sub 0.2}Mn{sub 0.54}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} half-type cell at 1C charge/discharge rate. The (0 0 3) and (1 0 4) diffraction peaks which represent layered {alpha}-NaFeO{sub 2} type structure (space group R-3m) were observed. Optimal magnetron sputtering conditions were detected. The 500 Degree-Sign C annealed thin film after deposited at 10 m Torr in Ar:O{sub 2}=3:1 shows a high discharge capacity of around 62 {mu}Ah/cm{sup 2} {mu}m with a high cyclic retention. - Graphical abstract: The Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} films is suitable for Lithium thin film battery. The film exhibits great discharge capacity (62 {mu}Ah/cm{sup 2} {mu}m) up to 200 cycles. Highlights: Black-Right-Pointing-Pointer High capacity thin films were deposited by RF magnetron sputtering. Black-Right-Pointing-Pointer Sputtering conditions were optimized by structural and electrochemical analysis. Black-Right-Pointing-Pointer Li[Li{sub 0.2}Mn{sub 0.56}Ni{sub 0.13}Co{sub 0.13}]O{sub 2} thin film shows a high capacity, 62 {mu}Ah/cm{sup 2} {mu}m. Black-Right-Pointing-Pointer The thin film shows an excellent cycling stability up to 200 cycles.

36 MATERIALS SCIENCE↗

Investigations on the growth and characterization of vertically aligned zinc oxide nanowires by radio frequency magnetronsputtering

Undoped vertically aligned ZnO nanowires have been grown on silicon (111) substrates by the rf magnetron sputtering technique without metal catalyst. The diameter, length and density distributions of the nanowires have been analyzed with respect to the different growth durations. The tapering of the nanowires is observed for the growth duration of 120 min owing to the insufficient adatoms on the growth front. In the X-ray diffraction pattern, the dominant (002) peak with narrow full width at half maximum (FWHM) of ZnO nanowires indicates the c-axis orientation and high crystalline nature with hexagonal wurtzite crystal structure. The narrow FWHM of E{sub 2}{sup low} and E{sub 2}{sup high} phonon modes (1.4 and 9.1 cm{sup −1}) provide an additional evidence for the high crystalline and optical properties of the nanowires. The low temperature photoluminescence spectra are dominated by the green emission at∼2.28 eV induced by the electron transitions between shallow donor and acceptor energy levels. - Graphical abstract: Coalescence free vertically aligned ZnO nanowires have been grown on silicon (111) substrate by the radio frequency magnetron sputtering technique. Highlights: ► ZnO nanowires have been grown by rf magnetron sputtering. ► A morphologically superior and coalescence free ZnO nanowires have been realized. ► ZnO nanowires exhibit hexagonal wurtzite crystal structure. ► A dominant visible emission indicates the presence of point defects in nanowires.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

On-site Real-Time Inspection System for Pump-impeller using X-band Linac X-ray Source

The methods of nondestructive testing (NDT) are generally ultrasonic, neutron, eddy-current and X-rays, NDT by using X-rays, in particular, is the most useful inspection technique having high resolution. We can especially evaluate corroded pipes of petrochemical complex, nuclear and thermal-power plants by the high energy X-ray NDT system. We develop a portable X-ray NDT system with X-band linac and magnetron. This system can generate a 950 keV electron beam. We are able to get X-ray images of samples with 1 mm spatial resolution. This system has application to real time impeller inspection because linac based X-ray sources are able to generate pulsed X-rays. So, we can inspect the rotating impeller if the X-ray pulse rate is synchronized with the impeller rotation rate. This system has application in condition based maintenance (CBM) of nuclear plants, for example. However, 950 keV X-ray source can only be used for thin tubes with 20 mm thickness. We have started design of a 3.95 MeV X-band linac for broader X-ray NDT application. We think that this X-ray NDT system will be useful for corrosion wastage and cracking in thicker tubes at nuclear plants and impeller of larger pumps. This system consists of X-band linac, thermionic cathode electron gun, magnetron and waveguide components. For achieving higher electric fields the 3.95 MeV X-band linac structure has the side-coupled acceleration structure. This structure has more efficient acceleration than the 950 keV linac with alternating periodic structure (APS). We adopt a 1.3 MW magnetron for the RF source. This accelerator system is about 30 cm long. The beam current is about 150 mA, and X-ray dose rate is 10 Gy at 1 m/500 pps. In this paper, the detail of the whole system concept and the electromagnetic field of designed linac structure will be reported.

43 PARTICLE ACCELERATORS↗

Comparative analysis of continuous-wave surface-plasma negative ion sources with various discharge geometry

Negative ion extraction from continuous-wave (CW) magnetron and semiplanotron discharges was studied and it was compared with that for the source with Penning electrode geometry. The CW negative ion beam up current to 13 mA was extracted from the magnetron source with emission aperture of 3.5 mm in diameter, while the beam with current up to 8 mA was obtained from the semiplanotron source modification. Characteristics of CW magnetron and semiplanotron sources are presented and analyzed.

43 PARTICLE ACCELERATORS↗

Two-dimensional single-stream electron motion in a coaxial diode with magnetic insulation

One of the most widespread models of electrons drifting around the cathode in magnetrons is the single-stream state, which is the Brillouin stream with purely azimuthal motion. We describe a single-stream state in which electrons not only move in the azimuthal direction, but also along the axial direction, which is useful for consideration, for example, of relativistic magnetrons, MILOs, and coaxial transmission lines. Relations are given for the conditions of magnetic insulation for 2D electron motion, for 1D azimuthal and axial motion, and for synchronism of these streams with the operating waves of M-type microwave sources. Relations are also provided for the threshold of generation in magnetrons with 2D electron motion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗