Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Li plating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

High-Performance InZn Alloy Anodes toward Practical Aqueous Zinc Batteries

Aqueous Zn batteries have high safety, low-cost and potential of delivering comparable energy density to alkali-ion batteries. However, its practical application is largely hampered by the limited cycle life associated with Zn anodes under conditions of high depth of discharge and high plating current densities. In this work, we report on electrodeposited indium-zinc alloy anodes that have well-dispersed zinc-domains surrounding indium domains that form a porous structure after dealloying which greatly improves tolerance to Zn dendrite formation. The InZn anodes exhibit low polarization of ~5 to 25 mV and demonstrate 700 cycles at a current density of ~10 mA cm -2 with a capacity of 5 mAh cm-2 capacity (45% depth-of-discharge). Full cells with an InZn anode, dibenzo[b,i]thianthrene-5,7,12,14-tetraone (DTT) cathode, in 2M ZnSO 4 deliver a capacity of ~ 110 mAh g -1 and good stability over 40 cycles. Finally, the work reveals a rational design of Zn-based anodes towards practical battery applications and opens the curtain for future development of aqueous Zn batteries.

25 ENERGY STORAGE↗

Anti-fungal bioactive terpenoids in the bioenergy crop switchgrass (Panicum virgatum) may contribute to ecotype-specific microbiome composition

Abstract Plant derived bioactive small molecules have attracted attention of scientists across fundamental and applied scientific disciplines. We seek to understand the influence of these phytochemicals on rhizosphere and root-associated fungi. We hypothesize that – consistent with accumulating evidence that switchgrass genotype impacts microbiome assembly – differential terpenoid accumulation contributes to switchgrass ecotype-specific microbiome composition. An initial in vitro Petri plate-based disc diffusion screen of 18 switchgrass root derived fungal isolates revealed differential responses to upland- and lowland-isolated metabolites. To identify specific fungal growth-modulating metabolites, we tested fractions from root extracts on three ecologically important fungal isolates – Linnemania elongata, Trichoderma sp. and Fusarium sp. Saponins and diterpenoids were identified as the most prominent antifungal metabolites. Finally, analysis of liquid chromatography-purified terpenoids revealed fungal inhibition structure – activity relationships (SAR). Saponin antifungal activity was primarily determined by the number of sugar moieties – saponins glycosylated at a single core position were inhibitory whereas saponins glycosylated at two core positions were inactive. Saponin core hydroxylation and acetylation were also associated with reduced activity. Diterpenoid activity required the presence of an intact furan ring for strong fungal growth inhibition. These results inform future breeding and biotechnology strategies for crop protection with reduced pesticide application.

09 BIOMASS FUELS↗

Compact single-shot soft X-ray photon spectrometer for free-electron laser diagnostics

The photon spectrum from free-electron laser (FEL) light sources offers valuable information in time-resolved experiments and machine optimization in the spectral and temporal domains. We have developed a compact single-shot photon spectrometer to diagnose soft X-ray spectra. The spectrometer consists of an array of off-axis Fresnel zone plates (FZP) that act as transmission-imaging gratings, a Ce:YAG scintillator, and a microscope objective to image the scintillation target onto a two-dimensional imaging detector. This spectrometer operates in segmented energy ranges which covers tens of electronvolts for each absorption edge associated with several atomic constituents: carbon, nitrogen, oxygen, and neon. The spectrometer’s performance is demonstrated at a repetition rate of 120 Hz, but our detection scheme can be easily extended to 200 kHz spectral collection by employing a fast complementary metal oxide semiconductor (CMOS) line-scan camera to detect the light from the scintillator. This compact photon spectrometer provides an opportunity for monitoring the spectrum downstream of an endstation in a limited space environment with sub-electronvolt energy resolution.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Preliminary investigation of an improved metal-dielectric cathode for magnetically insulated transmission line oscillator

In order to explore the cathode with good repetition quality for the magnetically insulated transmission line oscillators, an improved metal-dielectric cathode is proposed and investigated experimentally. The cathode is designed to be step-like shape, and thin copper plated boards are periodically and compactly arrayed on the surface of the cathode base, which ensures the uniformity of the electrons emitted from the cusps of the copper plated boards. According to the numerical simulation results, the step-like shape is beneficial to convert the kinetic energy of the magnetic insulating current partially and enhance the beam-wave interaction efficiency. Finally, a preliminary experiment of an L-band magnetically insulated transmission line oscillator (MILO) with the improved metal-dielectric cathode is carried out. A high power microwave (HPM) with an average power of 1.95 GW is generated from the MILO, with an efficiency of 13.5%. Under the same experiment condition, the output power and main frequency with the presented cathode are almost the same to those with the velvet cathode. Apart from that, metal-dielectric cathode has the merits of small outgassing and long lifetime, and all of these make the improved metal-dielectric cathode significantly promising for the MILO repetition operation.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Operando Analysis of Gas Evolution in TiNb 2 O 7 (TNO)-Based Anodes for Advanced High-Energy Lithium-Ion Batteries under Fast Charging

TiNb 2 O 7 (TNO) is regarded as one of the promising next-generation anode materials for lithium-ion batteries (LIBs) due to its high rate capabilities, higher theoretical capacity, and higher lithiation voltage. Furthermore, this enables the cycling of TNO-based anodes under extreme fast charging (XFC) conditions with a minimal risk of lithium plating compared to that of graphite anodes. Here, the gas evolution in real time with TNO-based pouch cells is first reported via operando mass spectrometry. The main gases are identified to be CO 2 , C 2 H 4 , and O 2 . A solid–electrolyte interphase is detected on TNO, which continues evolving, forming, and dissolving with the lithiation and delithiation of TNO. The gas evolution can be significantly reduced when a protective coating is applied on the TNO particles, reducing the CO 2 and C 2 H 4 evolution by ~2 and 5 times, respectively, at 0.1C in a half-cell configuration. The reduction on gas generation in full cells is even more pronounced. The surface coating also enables 20% improvement in capacity under XFC conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modelling of radiative divertor operation towards detachment in experimental advanced superconducting tokamak

In order to actively control power load on the divertor target plates and study the effect of radiative divertor on plasma parameters in divertor plasmas and heat fluxes to the targets, dedicated experiments with Ar impurity seeding have been performed on experimental advanced superconducting tokamak in typical L-mode discharge with single null divertor configuration, ohmic heating power of 0.5 MW, and lower hybrid wave heating power of 1.0 MW. Ar is puffed into the divertor plasma at the outer target plate near the separatrix strike point with the puffing rate 1.26 Multiplication-Sign 10{sup 20} s{sup -1}. The radiative divertor is formed during the Ar puffing. The SOL/divertor plasma in the L-mode discharge with radiative divertor has been modelled by using SOLPS5.2 code package [V. Rozhansky et al., Nucl. Fusion 49, 025007 (2009)]. The modelling shows the cooling of the divertor plasma due to Ar seeding and is compared with the experimental measurement. The changes of peak electron temperature and heat fluxes at the targets with the shot time from the modelling results are similar to the experimental measurement before and during the Ar impurity seeding, but there is a major difference in time scales when Ar affects the plasma in between experiment and modelling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Buckling analysis of planar compression micro-springs

Large compression deformation causes micro-springs buckling and loss of load capacity. We analyzed the impact of structural parameters and boundary conditions for planar micro-springs, and obtained the change rules for the two factors that affect buckling. A formula for critical buckling deformation of micro-springs under compressive load was derived based on elastic thin plate theory. Results from this formula were compared with finite element analysis results but these did not always correlate. Therefore, finite element analysis is necessary for micro-spring buckling analysis. We studied the variation of micro-spring critical buckling deformation caused by four structural parameters using ANSYS software under two constraint conditions. The simulation results show that when an x-direction constraint is added, the critical buckling deformation increases by 32.3-297.9%. The critical buckling deformation decreases with increase in micro-spring arc radius or section width and increases with increase in micro-spring thickness or straight beam width. We conducted experiments to confirm the simulation results, and the experimental and simulation trends were found to agree. Buckling analysis of the micro-spring establishes a theoretical foundation for optimizing micro-spring structural parameters and constraint conditions to maximize the critical buckling load.

36 MATERIALS SCIENCE↗

Letter to the editor: Cone partitioned plate (CPP) vs circular couette

In geometries capable of producing uniform shear stress across the gap such as cone plate, it is a challenge to study the nonlinear rheology of well-entangled polymers without wall slip and edge fracture. The task to obtain meaningful steady-state information is particularly daunting. Significant insights are required in the design of experiments and choice of reliable apparatuses that could fulfill the objective to determine the constitutive behavior. In a recent published article, Hu J. Rheol. 54, 1307 1323 (2010) reported particle-imaging velocimetric measurements of two highly entangled polybutadiene solutions with a cocylinder geometry. One of the solutions was prepared and provided to Hu by Ravindranath from the University of Akron. Rheological and particletracking velocimetric studies have been carried out on the same sample in our laboratory. In this letter, we will compare Hu s results with our own measurements, clarify a few misrepresentations, and discuss several important issues concerning shear banding in entangled polymers.

Ravindranath, Sham↗

High performance computation of residual stress and distortion in laser welded 301L stainless sheets

Transient thermo-mechanical simulation of stainless plate laser welding process was performed by a highly efficient and accurate approach-hybrid iterative substructure and adaptive mesh method. Especially, residual stress prediction was enhanced by considering various heat effects in the numerical model. The influence of laser welding heat input on residual stress and welding distortion of stainless thin sheets were investigated by experiment and simulation. X-ray diffraction (XRD) and contour method were used to measure the surficial and internal residual stress respectively. Effect of strain hardening, annealing and melting on residual stress prediction was clarified through a parametric study. It was shown that these heat effects must be taken into account for accurate prediction of residual stresses in laser welded stainless sheets. Reasonable agreement among residual stresses by numerical method, XRD and contour method was obtained. Buckling type welding distortion was also well reproduced by the developed thermo-mechanical FEM.

36 MATERIALS SCIENCE↗

Slow slip source characterized by lithological and geometric heterogeneity

Slow slip events (SSEs) accommodate a significant proportion of tectonic plate motion at subduction zones, yet little is known about the faults that actually host them. The shallow depth (<2 km) of well-documented SSEs at the Hikurangi subduction zone offshore New Zealand offers a unique opportunity to link geophysical imaging of the subduction zone with direct access to incoming material that represents the megathrust fault rocks hosting slow slip. Two recent International Ocean Discovery Program Expeditions sampled this incoming material before it is entrained immediately down-dip along the shallow plate interface. Drilling results, tied to regional seismic reflection images, reveal heterogeneous lithologies with highly variable physical properties entering the SSE source region. These observations suggest that SSEs and associated slow earthquake phenomena are promoted by lithological, mechanical, and frictional heterogeneity within the fault zone, enhanced by geometric complexity associated with subduction of rough crust.

58 GEOSCIENCES↗

Material migration studies with an ITER first wall panel proxy on EAST

The ITER beryllium (Be) first wall (FW) panels are shaped to protect leading edges between neighbouring panels arising from assembly tolerances. This departure from a perfectly cylindrical surface automatically leads to magnetically shadowed regions where eroded Be can be re-deposited, together with co-deposition of tritium fuel. To provide a benchmark for a series of erosion/re-deposition simulation studies performed for the ITER FW panels, dedicated experiments have been performed on the EAST tokamak using a specially designed, instrumented test limiter acting as a proxy for the FW panel geometry. Carbon coated molybdenum plates forming the limiter front surface were exposed to the outer midplane boundary plasma of helium discharges using the new Material and Plasma Evaluation System (MAPES). Net erosion and deposition patterns are estimated using ion beam analysis to measure the carbon layer thickness variation across the surface after exposure. The highest erosion of about 0.8 µm is found near the midplane, where the surface is closest to the plasma separatrix. No net deposition above the measurement detection limit was found on the proxy wall element, even in shadowed regions. The measured 2D surface erosion distribution has been modelled with the 3D Monte Carlo code ERO, using the local plasma parameter measurements together with a diffusive transport assumption. In conclusion, excellent agreement between the experimentally observed net erosion and the modelled erosion profile has been obtained.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Coupling of the FUN3D Unstructured Flow Solver and the LASTRAC Stability Code to Model Transition

We develop an iterative automated method to predict transition locations in boundary-layer flows by using the FUN3D solver to perform flow simulations and the LASTRAC code for linear stability computations. The coupling of FUN3D and LASTRAC allows for a robust physics-based approach to model boundary-layer transition by analyzing the growth of different instability waves and then using that information to iteratively update the resulting transition location. There is no user involvement during the iterative computations. We apply this automated method to subsonic flow over a flat plate with a sharp leading edge. The final solution has regions of laminar and turbulent flow with a transition onset location that agrees with experiments and stability-based correlations. This iterative automated method is also applied to an NLF(1)-0416 airfoil for conditions with and without a separation bubble. Along with predicting transition locations, we compare the streamwise distributions of surface-pressure and skin-friction coefficients to a transport-equation-based model. We consider a 6:1 prolate spheroid at three angles of attack, namely, five, ten, and fifteen degrees, where mixed-mode transition occurs due to both Tollmien-Schlichting and crossflow instabilities. The skin-friction contours and transition fronts at every angle of attack from our iterative automated method show good agreement with past experimental and computational results in the literature for the 6:1 prolate spheroid.

Transition↗

Multiscale modeling of the influence of Fe content in a Al-Si-Cu alloy on the size distribution of intermetallic phases and micropores

A multiscale model was developed to simulate the formation of Fe-rich intermetallics and pores in quaternary Al-Si-Cu-Fe alloys. At the microscale, the multicomponent diffusion equations were solved for multiphase (liquid-solid-gas) materials via a finite difference framework to predict microstructure formation. A fast and robust decentered plate algorithm was developed to simulate the strong anisotropy of the solid/liquid interfacial energy for the Fe-rich intermetallic phase. The growth of porosity was controlled by local pressure drop due to solidification and interactions with surrounding solid phases, in addition to hydrogen diffusion. The microscale model was implemented as a subroutine in a commercial finite element package, producing a coupled multiscale model. This allows the influence of varying casting conditions on the Fe-rich intermetallics, the pores, and their interactions to be predicted. Synchrotron x-ray tomography experiments were performed to validate the model by comparing the three-dimensional morphology and size distribution of Fe-rich intermetallics as a function of Fe content. Large platelike Fe-rich {beta} intermetallics were successfully simulated by the multiscale model and their influence on pore size distribution in shape castings was predicted as a function of casting conditions.

36 MATERIALS SCIENCE↗

SU-E-T-283: Dose Perturbations Near Heterogeneity Junctions for Modulated-Scanning Protons

Purpose: To compare calculated and measured doses near heterogeneity junctions of tissue-substitute materials for modulated-scanning protons. Methods: Three heterogeneous phantoms were configured using slabs of various plastics to simulate lung, fat, soft-tissue (polystyrene), and bone with known relative linear stopping powers (RLSPs). Each phantom consisted of soft-tissue and a single heterogeneity of a 5 or 10 cm thickness of a non-soft-tissue material. CT images were loaded into a Syngo treatment planning system and each material contoured and assigned its RLSP. Planning target volumes (PTVs) were drawn such that a beam would partially traverse the heterogeneity and partially only soft-tissue. Lateral profiles were measured using EDR2 films at a minimum of six depths between the phantom surface and the depth corresponding to the beam range. Absolute doses were measured inside and distal to the PTV in all phantoms using either a parallel plate or thimble chamber. Additional dose measurements were made between two lung slabs. Results: Profiles measured by film generally agreed with calculations except for depths distal to lung and fat junctions. Measured lateral penumbras for depths at the distal junction of lung were found to be wider than calculated ones. Compared with calculated doses, measured doses in the PTVs were 5.19% and 2.51% lower for lung and fat respectively but for bone were 0.2% higher. Measured doses for depths distal to the PTV were up to 29.65% and 10.58% higher for lung and fat, respectively but 6.30% lower for bone. Conclusion: The low measured doses in the PTVs for lung and fat might be due to underestimation of lateral scattering of protons. The higher measured doses distal to the PTV for the lung and fat are a Result of a shortened calculated beam range whereas the higher dose distal to the bone junction is within uncertainties.

60 APPLIED LIFE SCIENCES↗

Tensile properties, strain rate sensitivity, and activation volume of additively manufactured 316L stainless steels [Tensile properties of 316L stainless steels made by laser powder-bed-fusion additive manufacturing]

The tensile properties of additively manufactured (AM) metals and alloys are among the most important variables that impact the potential applications of these materials. Here we examine and report on the tensile properties of AM 316L stainless steels fabricated by the laser powder-bed-fusion (L-PBF) technique, via twelve sets of optimized laser processing parameters that produce materials with density >98.8 ± 0.10%. A heterogeneous microstructure is observed in all L-PBF samples, including microscopic features such as dislocations, cellular walls, elemental segregations, local misorientations, impurities, precipitates, and a large fraction of low-angle grain boundaries (2-10°, ~40–60%). The derived average grain size defined by high-angle grain boundaries (>10°) is ~30–50 μm. Tensile testing reveals a yield strength ranging from 552 to 635 MPa and a tensile-elongation-to-failure (TEF) of 0.09–0.42 for directly-printed samples, whereas these values are 592–690 MPa and 0.29–0.50 for samples machined from the as-built rectangular thin plates. In all samples, we observe a variation of tensile yield strength within ~15% but not the TEF, suggesting marginal microstructural changes despite a wide range of laser processing parameters. The large scatter of TEF in directly-printed samples originates from the sensitivity of thin gauge geometry (~2 mm 2 cross-section area) to the built-in flaws. We measured a substantially higher strain rate sensitivity (m~0.02–0.03) of L-PBF 316L compared to the coarse-grained counterparts (~0.006), together with a small activation volume of ~20–30b3 (where b is the Burgers vector of 316L). In conclusion, these deformation kinetics parameters suggest that the tensile plasticity of L-PBF 316L is controlled by a much finer microstructural length scale than the measured grain size, consistent with the high strength and juxtaposed nano- to macro-structures seen in these materials. Strategies to optimize the tensile properties of AM materials are discussed.

36 MATERIALS SCIENCE↗

Patients with idiopathic endplate inflammation displayed aberrant Th17 responses resulting in proinflammatory monocyte activation

Endplate inflammation remains a difficult task to diagnose and treat, partly due to the absence of in-depth understanding of the cellular and molecular factors driving this condition. In the current study, we investigated the circulating immune cells in patients with idiopathic endplate inflammation. Compared to healthy controls, the patients with endplate inflammation presented a significant upregulation of Th17 cells, characterized by higher frequencies of circulating IL-17{sup +}CD4{sup +} T cells examined directly ex vivo and after PMA and ionomycin (PMA/I) stimulation. The frequency of Th17 cells in patients was not correlated with patient age, sex, or smoking status, but was significantly correlated with patient BMI. The total CD4{sup +} T cells from patients with end plate inflammation also presented significantly higher levels of IL-17 secretion directly ex vivo and after PMA/I stimulation. The IL-17 secretion was primarily mediated by CCR4{sup +}CCR6{sup +} CD4{sup +} T cells, followed by CCR4{sup -}CCR6{sup +} CD4{sup +} T cells and was nearly absent in CCR4{sup -}CCR6{sup -} CD4{sup +} T cells. Monocytes incubated with CCR4{sup +}CCR6{sup +} CD4{sup +} T cells presented significantly higher MHC class II expression, as well as higher CD80 and CD86 expression. The secretion of IL-6 and TNF was significantly higher in cell cultures containing CCR4{sup +}CCR6{sup +} CD4{sup +} T cells than in cell cultures containing CCR4{sup -}CCR6{sup -} CD4{sup +} T cells. These effects were reduced when the IL-17A cytokine was neutralized. Together, we identified a systemic upregulation of Th17 responses that could contribute to proinflammatory monocyte activation in patients with endplate inflammation.

60 APPLIED LIFE SCIENCES↗

Novel high-power subterahertz-range radial surface wave oscillator

A novel high-power subterahertz-range radial surface wave oscillator (SWO), in which the electron beam is emitted radially and interacts with the slow wave structure (SWS) machined on a planar plate, is presented in this paper. Compared to the axial SWO where the electron beam is emitted axially and interacts with the SWS machined on the inner wall of a cylindrical waveguide, the radial SWO has two advantages. One is that fabrication of the radial SWS is much easier than that of the axial SWO. The other is that the radial SWO is a low-impedance device, it can produce much higher current than the axial SWO when they are driven by the same driven voltage, and hence, it may generate much higher output power. Particle-in-cell simulation results demonstrate that the proposed radial SWO driven by the voltage of 312 kV can produce the terahertz wave with the mean output power of 680 MW at the frequency of 0.142 THz, it has a very pure TM{sub 01} mode and the higher modes can be effectively suppressed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Synthesis and characterization of 5-fluorocytosine intercalated Zn-Al layered double hydroxide

In this paper, the intercalation of 5-fluorocytosine (5-FC) into a layered inorganic host, Zn-Al layered double hydroxide (LDH), has been carried out using coprecipitation method to obtain 5-FC/LDH nanohybrids. The intercalated amount (A{sub In}) of 5-FC into the LDH is remarkably dependent on the molar ratio (R{sub F/M}) of 5-FC to metal ions and the pH of coprecipitation system. The morphology of 5-FC molecules in 5-FC/LDH nanohybrids is dependent on the A{sub In}. It is interestingly found that the morphology of the nanohybrid particles may be changed with the increase of R{sub F/M} from hexagonal plate particles to threadlike particles. The in vitro drug release from the nanohybrids is remarkably lower than that from the corresponding physical mixture and pristine 5-FC at either pH 4.8 or pH 7.5. In addition, the release rate of 5-FC from the nanohybrid at pH 7.5 is remarkably lower than that at pH 4.8, this is due to a possible difference in the release mechanism. The obtained results show these drug-inorganic nanohybrids can be used as a potential drug delivery system. - Graphical abstract: The 5-fluorocytosine (5-FC) has been intercalated into layered double hydroxide using coprecipitation method. The morphology of 5-FC molecules in obtained nanohybrids was dependent on the intercalated amount of 5-FC. The in vitro drug release from the nanohybrids was remarkably lower than that from the corresponding physical mixture, which shows these drug-inorganic nanohybrids can be used as a potential drug delivery system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗