Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LUBRICATION - FRICTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Measurement of viscosity and elasticity of lubricants at high pressures

The oscillating quartz crystal viscometer has been used to investigate possible viscoelastic behavior in synthetic lubricating fluids and to obtain viscosity-pressure-temperature data for these fluids at temperatures to 300 F and pressures to 40,000 psig. The effect of pressure and temperature on the density of the test fluids was measured concurrently with the viscosity measurements. Viscoelastic behavior of one fluid, di-(2-ethylhexyl) sebacate, was observed over a range of pressures. These data were used to compute the reduced shear elastic (storage) modulus and reduced loss modulus for this fluid at atmospheric pressure and 100 F as functions of reduced frequency.

Rein, R. G., Jr.↗
NASA NTRS1976

Analysis of the gas-lubricated flat-sector-pad thrust bearing

A flat sector-shaped pad geometry for a gas-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. It is shown that maximum load capacity is achieved when the pad is tilted so as to create uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves, and a comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗
NASA NTRS1975

Isothermal elastohydrodynamic lubrication of point contacts. I - Theoretical formulation

The analysis of an isothermal elastohydrodynamic lubrication (EHL) point contact was evaluated numerically. This required the simultaneous solution of the elasticity and Reynolds equations. In the elasticity analysis the contact zone is divided into equal rectangular areas and it is assumed that a uniform pressure is applied over each element. In the numerical analysis of the Reynolds' equation a phi analysis where phi is equal to the pressure times the film thickness to the 3/2 power is used to help the relaxation process. The EHL point contact analysis is applicable for the entire range of elliptical parameters and is valid for any combination of rolling and sliding within the contact.

Hamrock, B. J.↗
NASA NTRS1977

Infrared temperature maps of EHD lubrication

Technique uses an infrared detector with two specially selected infrared filters, in separately mapping the contact-surface temperature and average oil-film temperature in an elastohydrodynamic conjunction. Apparatus includes conventional four-ball bearing tester and temperature controlled lubricant system.

Sanborn, D. M.↗
NASA NTRS1978

Determining minimum lubrication film for machine parts

Formula predicts minimum film thickness required for fully-flooded ball bearings, gears, and cams. Formula is result of study to determine complete theoretical solution of isothermal elasto-hydrodynamic lubrication of fully-flooded elliptical contacts.

Hamrock, B. J.↗
NASA NTRS1976

Isothermal elastohydrodynamic lubrication of point contacts. III: Fully flooded results

The influence of the ellipticity parameter and the dimensionless speed U, load W, and material G parameters on minimum film thickness was investigated. The ellipticity parameter k was varied from 1 (a ball-on-plate configuration) to 8 (a configuration approaching a line contact). The dimensionless speed parameter was varied over a range of nearly two orders of magnitude. And the dimensionless load parameter was varied over a range of one order of magnitude. Conditions corresponding to the use of solid materials of bronze, steel, and silicon nitride and lubricants of paraffinic and naphthenic mineral oils were considered in obtaining the exponent on the dimensionless material parameter.

Hamrock, B. J.↗
NASA NTRS1977

Design charts for arbitrarily pivoted, liquid-lubricated flat-sector-pad thrust bearing

A flat, sector-shaped geometry for a liquid-lubricated thrust bearing is analyzed considering both the pitch and roll of the pad. Results are presented in design charts that enable a direct approach to the design of point- and line-pivoted, tilting pad bearings. A comparison is made with the Mitchell bearing approximation and it is found that this approximation always overestimates load capacity.

Etsion, I.↗
NASA NTRS1977

Elastohydrodynamic lubrication of elliptical contacts for materials of low elastic modulus. 1: Fully flooded conjunction

Elastohydrodynamic lubrication concepts of conjunctions of elliptical form are applied to materials of low elastic modulus. The influence of the ellipticity parameter and the dimensionless speed, load, and material parameters on minimum film thickness for these materials has been investigated. The ellipticity parameter was varied from a ball on plate configuration to a configuration approaching a line contact. The dimensionless speed and load parameters were varied by 1 order of magnitude. Seventeen different cases were used to generate minimum and central film thickness relations. Contour plots are presented that illustrate the pressure distribution and film thickness in the conjunction.

Hamrock, B. J.↗
NASA NTRS1977

Study of Lubricant Jet Flow Phenomena in Spur Gears: Out of Mesh Condition

Oil jet lubrication on the disengaging side of a gear mesh was analyzed. Results of the analysis were computerized and used to determine the oil jet impingement depth for several gear ratios and oil jet to pitch line velocity ratios. A gear test rig using high speed photography was used to experimentally determine the oil jet impingement depth on the disengaging side of mesh. Impingement depth reached a maximum at gear ratio near 1.5 where chopping by the leading gear tooth limited impingement depth. The pinion impingement depth is zero above a gear ratio of 1.172 for a jet velocity to pitch time velocity ration of 1.0 and is similar for other velocity ratios. The impingement depth for gear and pinion are equal and approximately one half the maximum at a gear ration of 7.0.

Townsend, D. P.↗
NASA NTRS1976

An accurate solution of the gas lubricated, flat sector thrust bearing

A flat sector shaped pad geometry for gas lubricated thrust bearings is analyzed considering both pitch and roll angles of the pad and the true film thickness distribution. Maximum load capacity is achieved when the pad is tilted so as to create a uniform minimum film thickness along the pad trailing edge. Performance characteristics for various geometries and operating conditions of gas thrust bearings are presented in the form of design curves. A comparison is made with the rectangular slider approximation. It is found that this approximation is unsafe for practical design, since it always overestimates load capacity.

Etsion, I.↗
NASA NTRS1978

Bearing, gearing, and lubrication technology

Results of selected NASA research programs on rolling-element and fluid-film bearings, gears, and elastohydrodynamic lubrication are reported. Advances in rolling-element bearing material technology, which have resulted in a significant improvement in fatigue life, and which make possible new applications for rolling bearings, are discussed. Research on whirl-resistant, fluid-film bearings, suitable for very high-speed applications, is discussed. An improved method for predicting gear pitting life is reported. An improved formula for calculating the thickness of elastohydrodynamic films (the existence of which help to define the operating regime of concentrated contact mechanisms such as bearings, gears, and cams) is described.

Anderson, W. J.↗
NASA NTRS1978

Statistical model for asperity-contact time fraction in elastohydrodynamic lubrication

Relations for the asperity contact time fraction during elastohydrodynamic (EHD) lubrication of a typical ball bearing are presented. The analysis is based on a two-dimensional random surface model, and actual profile traces of the bearing surfaces were used as statistical sample records. The results of the analysis show that transition from 90 percent contact to 1 percent contact occurs within a dimensionless film thickness range of approximately 4 to 5. This thickness ratio is several times larger than reported in the literature where one-dimensional random surface models were used.

Sidik, S. M.↗
NASA NTRS1978

Principles of ESCA and application to metal corrosion, coating and lubrication

The principles of ESCA (electron spectroscopy for chemical analysis) were described by comparison with other spectroscopic techniques. The advantages and disadvantages of ESCA as compared to other surface sensitive analytical techniques were evaluated. The use of ESCA was illustrated by actual applications to oxidation of steel and Rene 41, the chemistry of lubricant additives on steel, and the composition of sputter deposited hard coatings. A bibliography of material that was useful for further study of ESCA was presented and commented upon.

Wheeler, D. R.↗
NASA NTRS1978

Hydrodynamic air lubricated compliant surface bearing for an automotive gas turbine engine. 1: Journal bearing performance

A 38.1 mm (1.5 inch) diameter Hydresil Compliant Surface Air Lubricated Journal Bearing was designed and tested to obtain bearing performance characteristics at both room temperature and 315 C (600 F). Testing was performed at various speeds up to 60,000 rpm with varying loads. Rotating sensors provided an opportunity to examine the film characteristics of the compliant surface bearing. In addition to providing minimum film thickness values and profiles, many other insights into bearing operation were gained such as the influence of bearing fabrication accuracy and the influence of smooth foil deflection between the bumps.

Ruscitto, D.↗
NASA NTRS1978

Hydrodynamic air lubricated compliant surface bearing for an automotive gas turbine engine. 2: Materials and coatings

Material coatings for an air-lubricated, compliant journal bearing for an automotive gas turbine engine were exposed to service test temperatures of 540 C or 650 C for 300 hours, and to 10 temperature cycles from room temperatures to the service test temperatures. Selected coatings were then put on journal and partial-arc foils and tested in start-stop cycle tests at 14 kPa (2 psi) loading for 2000 cycles. Half of the test cycles were performed at a test chamber service temperature of 540 C (1000 F) or 650 C (1200 F); the other half were performed at room temperature. Based on test results, the following combinations and their service temperature limitations are recommended: HL-800 TM (CdO and graphite) on foil versus chrome carbide on journal up to 370 C (700 F); NASA PS 120 (Tribaloy 400, silver and CaF2 on journal versus uncoated foil up to 540 C (1000 F); and Kaman DES on journal and foil up to 640 C (1200 F). Kaman DES coating system was further tested successfully at 35 kPa (5 psi) loading for 2000 start-stop cycles.

Bhushan, B.↗
NASA NTRS1977

Study of lubricant jet flow phenomena in spur gears - Out of mesh condition

An analysis was conducted for oil jet lubrication on the disengaging side of a gear mesh. Results of the analysis were computerized and used to determine the oil jet impingement depth for several gear ratios and oil jet to pitch line velocity ratios. An experimental program was conducted on the NASA gear test rig using high-speed photography to experimentally determine the oil jet impingement depth on the disengaging side of mesh. Impingement depth reaches a maximum at gear ratio near 1.5 where chopping by the leading gear tooth limits the impingement depth. The pinion impingement depth is zero above a gear ratio of 1.172 for a jet velocity to pitch time velocity ratio of 1.0 and is similar for other velocity ratios. The impingement depth for gear and pinion are equal and approximately one-half the maximum at a gear ratio of 1.0. Impingement depth on either the gear or pinion many be improved by relocation of the jet from the pitch line or by changing the jet angle. Results of the analysis were verified by experimental results using a high-speed camera and a well lighted oil jet.

Townsend, D. P.↗