Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LOOPS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Experience with Chemical Looping Combustion of Coal in a 200 kW Dual Fluidized Bed Reactor

The University of Utah recently commissioned a dual fluidized bed process development unit (PDU) for investigating chemical looping combustion (CLC) and chemical looping with oxygen uncoupling (CLOU) of coal. The reactors and supporting systems were sized to support at least 200 kW of coal input based on available reaction rate data. Both the air reactor and fuel reactor are circulating fluidized beds and bed material passes between the reactors via loop seals. The reactors are refractory-lined rather than electrically heated, so the system must be preheated with natural gas before chemical looping combustion can begin. Air and steam are preheated through a combination of electric heating and natural gas burners and reactor product gas flows through heat exchangers and bag houses to cool and clean the gas of particulate. As is typical with pilot-scale systems, several operational challenges were encountered as the system was brought online and operation progressed from heatup and initial testing with gaseous fuels towards full CLOU processing of coal. The system hardware and operational procedures have undergone several modifications, but the PDU can now reliably be preheated to the operating temperature and coal can be fed at the target feed rate. This paper presents the PDU, describes the procedures for evaluating carbon conversion, CO2 capture and CO2 purity, and presents initial results from chemical looping combustion of coal with non-CLOU and CLOU carriers. General experience of operating the plant and notable challenges and solutions are also presented.

Whitty, Kevin J.↗

Development of a Small Liquid Sodium Purification Loop

Generation IV nuclear reactors provide management solutions to address spent fuel problems. The most researched Generation IV reactor is the sodium cooled fast reactor (SFR). Improved engineering is has allowed for systematic improvements in both the safety and efficiency of power production. However, before a SFR can be brought back online in the Untied States, constructive research must be pursued on numerous scales to ensure the capabilities of aforementioned reactors. While larger research facilities such as the one at Argonne National Laboratory or the University of Wisconsin - Madison address some of the larger scale studies surrounding the SFR, Fort Lewis College (FLC) is aiming to provide small scale studies on liquid sodium as a thermal hydraulic cooling system. The sodium diagnostic loop at FLC is constructed to conduct research that includes: analyzing pumping characteristics, thermal stratification, freeze plug analysis, and corrosion studies. The FLC loop is attached to an inert glovebox so these experiments can be conducted with an additional layer of safety. The objective of this sodium research apparatus is to combine the best features of each instrument commonly associated with sodium research loops in a cost effective manner while still obtaining high fidelity data. Furthermore, an innovative design of the loop maximizes the volume of available research space inside of the glovebox by mounting the diagnostic loop adjacent to the glovebox.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

6. Closed-Loop Toolpath Generation

Closed-loop paths, also known as closed-loop contours, are paths that start and stop at the same point and are typically used to define the perimeter or outermost boundary of the polygon that represents a given layer of an object, referred to as the “layer polygon.” Finding the location of a closed-loop path involves applying two offsetting steps to the edge of the layer polygon. The offsetting steps respectively serve to (1) find the area that contains the toolpath and (2) find the centerline of that area, to define the path itself. After finding the perimeter path, the remaining geometry from the layer polygon can be used for additional path-planning steps. This chapter will discuss how the location for a closed-loop path is found, including various problem scenarios, and the different types of closed-loop paths used in additive manufacturing.

Roschli, Alex↗

A novel approach to RF power coupling in Radio-Frequency Quadrupole (RFQ) structures: built-in coaxial double-loop coupling port

Efficient and reliable RF power couplers in accelerating cavities require precise impedance matching and mechanical stability to ensure optimal beam energy transfer. In radio-frequency quadrupole (RFQ) accelerators, power is commonly delivered using waveguide iris or coaxial loop couplers. Iris couplers can handle high RF power but lack tunability, while coaxial loop couplers offer tuning flexibility but are limited in power handling and thermal performance. We propose a new RFQ power coupling concept utilizing a single input coaxial center-fed double-loop antenna built into a vane in an RFQ structure . The design integrates back-to-back loops into the RFQ vanes, fed by a TEM coaxial transmission line with standard 50-Ω characteristic impedance. The configuration can allow straightforward and easy ceramic window replacement without retuning, and coupling strength is adjusted with protruding tuning rods. Numerical simulations, performed with both a simplified RFQ model and the Spallation Neutron Source RFQ, demonstrate improved RF performance and reduced dipole mode excitation. The results establish the coaxial double-loop coupler as a practical alternative for high-power RFQ coupling applications.

Lee, Sung-Woo [ORNL] (ORCID:000000030915835X)↗

Unprecedented irradiation resistance of nanocrystalline tungsten with equiaxed nanocrystalline grains to dislocation loop accumulation

Nanocrystalline metals are often postulated as irradiation tolerant materials due to higher grain boundary densities. The efficiency of these materials in mitigating irradiation damage is still under investigation. Here, we present an in-situ transmission electron microscopy with ion irradiation study on equiaxed 35 nm grained tungsten (NCW-35 nm) and compare its radiation tolerance, in terms of dislocation loop damage, to several other grades of tungsten with different grain sizes at two temperatures (RT and 1073 K). The NCW-35 nm was shown to possess significant higher radiation tolerance in terms of loop damage. As demonstrated by Kinetic Monte Carlo simulations, at least part of the higher radiation tolerance of the small grains is due to higher interstitial storage (at the grain boundaries) and defect recombination (in the grain interiors) in the small grain material. In addition, experimental observations reveal rapid and efficient dislocation loop absorption by the grain boundaries and this is considered the dominant factor for mass transport to the boundaries during irradiation, enabling the remarkable radiation tolerance of 35 nm grained tungsten. Furthermore, this study demonstrates the possibility of attaining high radiation tolerant materials, in terms of dislocation loop damage, by minimizing grain sizes in the nanocrystalline regime.

36 MATERIALS SCIENCE↗

Closed Loop Geothermal Working Group: GeoCLUSTER App, Subsurface Simulation Results, and Publications

To better understand the heat production, electricity generation performance, and economic viability of closed-loop geothermal systems in hot-dry rock, the Closed-Loop Geothermal Working Group -- a consortium of several national labs and academic institutions has tabulated time-dependent numerical solutions and levelized cost results of two popular closed-loop heat exchanger designs (u-tube and co-axial). The heat exchanger designs were evaluated for two working fluids (water and supercritical CO2) while varying seven continuous independent parameters of interest (mass flow rate, vertical depth, horizontal extent, borehole diameter, formation gradient, formation conductivity, and injection temperature). The corresponding numerical solutions (approximately 1.2 million per heat exchanger design) are stored as multi-dimensional HDF5 datasets and can be queried at off-grid points using multi-dimensional linear interpolation. A Python script was developed to query this database and estimate time-dependent electricity generation using an organic Rankine cycle (for water) or direct turbine expansion cycle (for CO2) and perform a cost assessment. This document aims to give an overview of the HDF5 database file and highlights how to read, visualize, and query quantities of interest (e.g., levelized cost of electricity, levelized cost of heat) using the accompanying Python scripts. Details regarding the capital, operation, and maintenance and levelized cost calculation using the techno-economic analysis script are provided. This data submission will contain results from the Closed Loop Geothermal Working Group study that are within the public domain, including publications, simulation results, databases, and computer codes. GeoCLUSTER is a Python-based web application created using Dash, an open-source framework built on top of Flask that streamlines the building of data dashboards. GeoCLUSTER provides users with a collection of interactive methods for streamlining the exploration and visualization of an HDF5 dataset. The GeoCluster app and database are contained in the compressed file geocluster_vx.zip, where the "x" refers to the version number. For example, geocluster_v1.zip is Version 1 of the app. This zip file also contains installation instructions. **To use the GeoCLUSTER app in the cloud, click the link to "GeoCLUSTER on AWS" in the Resources section below. To use the GeoCLUSTER app locally, download the geocluster_vx.zip to your computer and uncompress this file. When uncompressed this file comprises two directories and the geocluster_installation.pdf file. The geo-data app contains the HDF5 database in condensed format, and the GeoCLUSTER directory contains the GeoCLUSTER app in the subdirectory dash_app, as app.py. The geocluster_installation.pdf file provides instructions on installing Python, the needed Python modules, and then executing the app.

15 GEOTHERMAL ENERGY↗

Loop equation and exact soft anomalous dimension in $ \mathcal{N} $ = 4 super Yang-Mills

BPS Wilson loops in supersymmetric gauge theories have been the subjects of active research since they are often amenable to exact computation. So far most of the studies have focused on loops that do not intersect. In this paper, we derive exact results for intersecting 1/8 BPS Wilson loops in $ \mathcal{N} $ = 4 supersymmetric Yang-Mills theory, using a combination of supersymmetric localization and the loop equation in 2d gauge theory. The result is given by a novel matrix-model-like representation which couples multiple contour integrals and a Gaussian matrix model. We evaluate the integral at large N, and make contact with the string worldsheet description at strong coupling. As an application of our results, we compute exactly a small-angle limit (and more generally near-BPS limits) of the cross anomalous dimension which governs the UV divergence of intersecting Wilson lines. The same quantity describes the soft anomalous dimension of scattering amplitudes of W-bosons in the Coulomb branch.

't Hooftand Polyakov loops↗

Minimal area surfaces dual to Wilson loops and the Mathieu equation

The AdS/CFT correspondence relates Wilson loops in N=4 SYM to minimal area surfaces in AdS 5 × S 5 space. Recently, a new approach to study minimal area surfaces in AdS 3 c AdS 5 was discussed based on a Schroedinger equation with a periodic potential determined by the Schwarzian derivative of the shape of the Wilson loop. Here we use the Mathieu equation, a standard example of a periodic potential, to obtain a class of Wilson loops such that the area of the dual minimal area surface can be computed analytically in terms of eigenvalues of such equation. As opposed to previous examples, these minimal surfaces have an umbilical point (where the principal curvatures are equal) and are invariant under λ-deformations. In various limits they reduce to the single and multiple wound circular Wilson loop and to the regular light-like polygons studied by Alday and Maldacena. In this last limit, the periodic potential becomes a series of deep wells each related to a light-like segment. Small corrections are described by a tight-binding approximation. In the circular limit they are well approximated by an expansion developed by A. Dekel. In the particular case of no umbilical points they reduce to a previous solution proposed by J. Toledo. The construction works both in Euclidean and Minkowski signature of AdS 3 .

't Hooft and Polyakov loops↗

Carbon-Assisted, Continuous Syngas Production in a Chemical Looping Scheme

In the current energy and environment scenario, it is imperative to develop energy efficient routes for chemical manufacturing that also pave the way for mitigation of greenhouse gas emissions. This work presents an efficient pathway for continuous syngas production via a chemical looping conversion of the two most potent greenhouse gases—CH 4 , and CO 2 . The well-known dry-reforming process of converting CH 4 , and CO 2 to syngas is energy-intensive and suffers from catalyst deactivation. The chemical looping approach, on the other hand, provides avenues for mitigating catalyst deactivation and enabling improved energy efficiency. The key to such process enhancements lies in the intricate structure–function relationships of the catalyst and its correlation to the process variables. We present the reduction and oxidation characteristics of 5 wt.% Ni/Ce 1-x Zr x O 2 -based catalysts (x = 0, 0.4, and 0.625). We demonstrate low temperature CH4 activation over Ni-promoted samples as opposed to pure Ce 1-x Zr x O 2 . Moreover, our results depict an optimum regeneration of these catalysts when oxidized by CO 2 , and H 2 O, which allows for chemical looping operation of steam reforming of methane as well. Process variables were tuned to optimize the CH 4 conversion (over 80%), and H 2 /CO ratio at 650 °C. The critical surface reactions—carbon accumulation and gasification, and thermocatalytic CO 2 splitting were investigated to elucidate the dynamic nature of the catalyst surface. In conclusion, the impact of this work lies in showcasing the opportunities to design chemical looping reactors for energy efficient syngas production from waste greenhouse gases.

25 ENERGY STORAGE↗

Improved sensing of vertical velocity for vertical position control using loop voltage signals on EAST

Vertical position control of shaped plasma is critical for all elongated tokamaks to achieve safe and stable plasma discharge. In EAST, the in-vessel coil (IC) is employed for fast control of plasma vertical motion which power supply capabilities limits the controllability of vertical instability. Moreover, adequate signal-to-noise ratio of vertical position measurement can also realize an improvement in vertical control. In EAST, plasma vertical position Z p is produced nearly by all integrated magnetics, fast Z error signal is obtained by filtering from Zp. Then this fast Z error and its derivative term (dz/dt) are controlled by IC with a separate PD controller. Yet, it has a low signal-to-noise ratio which limits the gains that can be used successfully in the PD control loops. To provide less noisy dz/dt signal, the successful use of multiple up/down loop voltage pairs instead of derivative of z derived from magnetic probe signals will be discussed. Experiment show that even a single pair of loop voltage signal has better signal-to-noise ratio than differentiation of Z p . In addition, flux loop pickup signals from the IC current are also measured with series of positive and negative IC current pulses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interstitial loop transformations in FeCr

Here, we improve the Self-Evolving Atomistic Kinetic Monte Carlo (SEAKMC) algorithm by integrating the Activation Relaxation Technique nouveau (ARTn), a powerful open-ended saddle-point search method, into the algorithm. We use it to investigate the reaction of 37-interstitial 1/2[1 1 1] and 1/2[View the MathML source] loops in FeCr at 10 at.% Cr. They transform into 1/2[1 1 1], 1/2[View the MathML source], [1 0 0] and [0 1 0] 74-interstitial clusters with an overall barrier of 0.85 eV. We find that Cr decoration locally inhibits the rotation of crowdions, which dictates the final loop orientation. Moreover, the final loop orientation depends on the details of the Cr decoration. Generally, a region of a given orientation is favored if Cr near its interface with a region of another orientation is able to inhibit reorientation at this interface more than the Cr present at the other interfaces. Also, we find that substitutional Cr atoms can diffuse from energetically unfavorable to energetically favorable sites within the interlocked 37-interstitial loops conformation with barriers of less than 0.35 eV.

36 MATERIALS SCIENCE↗

Characterization of faulted dislocation loops and cavities in ion irradiated alloy 800H

Alloy 800H is a high nickel austenitic stainless steel with good high temperature mechanical properties which is considered for use in current and advanced nuclear reactor designs. The irradiation response of 800H was examined by characterizing samples that had been bulk ion irradiated at the Michigan Ion Beam Laboratory with 5 MeV Fe 2+ ions to 1, 10, and 20 dpa at 440 °C. Transmission electron microscopy was used to measure the size and density of both {111} faulted dislocation loops and cavities as functions of depth from the irradiated surface. The faulted loop density increased with dose from 1 dpa up to 10 dpa where it saturated and remained approximately the same until 20 dpa. The faulted loop average diameter decreased between 1 dpa and 10 dpa and again remained approximately constant from 10 dpa to 20 dpa. Cavities were observed after irradiation doses of 10 and 20 dpa, but not after 1 dpa. The average diameter of cavities increased with dose from 10 to 20 dpa, with a corresponding small decrease in density. Cavity denuded zones were observed near the irradiated surface and near the ion implantation peak. To further understand the microstructural evolution of this alloy, FIB lift-out samples from material irradiated in bulk to 1 and 10 dpa were re-irradiated in-situ in their thin-foil geometry with 1 MeV Kr 2+ ions at 440 °C at the Intermediate Voltage Electron Microscope. We observed that the cavities formed during bulk irradiation shrank under thin-foil irradiation in-situ while dislocation loops were observed to grow and incorporate into the dislocation network. The thin-foil geometry used for in-situ irradiation is believed to cause the cavities to shrink.

36 MATERIALS SCIENCE↗

Freeway Loop Detector Data Reconciliation Based on Vehicle Conservation

Loop detector is the most common source of traffic flow measurements on freeways. Though being a mature technology, loop detector is prone to miscounts even when it is properly deployed and adjusted. If a loop detectors systematically over- or under-counts, the estimation based on vehicle conservation leads to results that are not physically plausible such as negative density or density higher than the jam-density. Here we propose an optimization-based method in which plausible values of accumulation is guaranteed through explicit constraints. Compared to similar methods, the proposed method distinct in the following: (i) the optimization problem is convex therefore leads to shorter computational time; (ii) occupancy is also taken into account in order to estimate upper and lower bounds in the accumulation between stations; (iii) no modifications are required when data from one or multiple lanes are missing. The method is first validated using micro-simulation by disturbing the loop-detector from micro-simulation, applying the method and then comparing the results with the ground truth data. The results show the method is able to capture the average counts almost exactly while providing estimate of density with satisfactory accuracy. The method is also successfully applied in a scenario in which field-data is available.

data reconciliation↗

Enhancing subtilisin thermostability through a modified normalized B-factor analysis and loop-grafting strategy

Rational design–guided improvement of protein thermostability typically requires identification of residues or regions contributing to instability and introduction of mutations into these residues or regions. One popular method, B-FIT, utilizes B-factors to identify unstable residues or regions and combines them with other strategies, such as directed evolution. Here, we performed structure-based engineering to improve the thermostability of the subtilisin E-S7 (SES7) peptidase. The B-value of each residue was redefined in a normalized B-factor calculation, which was implemented with a refined bioinformatics analysis strategy to identify the critical area (loop 158–162) related to flexibility and to screen for suitable thermostable motif sequences in the Protein Data Bank that can act as transplant loops. In total, we analyzed 445 structures and identified 29 thermostable motifs as candidates. Using these motifs as a starting point, we performed iterative homologous modeling to obtain a desirable chimera loop and introduced five different mutations into this loop to construct thermostable SES7 proteins. Differential scanning fluorimetry revealed increases of 7.3 °C in the melting temperature of an SES7 variant designated M5 compared with the WT. The X-ray crystallographic structure of this variant was resolved at 1.96 Å resolution. The crystal structure disclosed that M5 forms more hydrogen bonds than the WT protein, consistent with design and molecular dynamics simulation results. In summary, the modified B-FIT strategy reported here has yielded a subtilisin variant with improved thermostability and promising industrial applications, supporting the notion that this modified method is a powerful tool for protein engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Observation and interpretation of negative remanent magnetization and inverted hysteresis loops in a thin film of La 0.7 Sr 0.3 MnO 3

The observation of inverted magnetic hysteresis loops and negative magnetic remanence (NRM) in a 7.6 nm thin film of La 0.7 Sr 0.3 MnO 3 grown on SrTiO 3 substrates is reported here. The film was grown employing pulsed laser deposition and characterized by reflection high-energy electron diffraction during growth and using x-ray reflectivity measurements post-growth. Magnetic properties of the film were measured from 5 K to 400 K under both the field-cooled (FC) and zero-field-cooled (ZFC) conditions. The observed results of inverted magnetic hysteresis loops and NRM are interpreted in terms of the co-existence of a magnetically inhomogeneous region consisting of superparamagnetic spin clusters with a blocking temperature $T_B$ = 240 K and the ferromagnetic state with an ordering temperature $T_C$ = 290 K. Hysteresis loop inversion is observed in the temperature region of $T_B < T < T_C$ whereas NRM appears in the mixed superparamagnetic and ferromagnetic states for $T < T_C$ down to 5 K. These observations of hysteresis loop inversion and NRM are related to the magneto-static interaction between the superparamagnetic and ferromagnetic phases leading to anti-alignment of spin of both magnetic phases with respect to each other.

inverted hysteresis loop↗

Analysis of Solar Receiver Performance for Chemical-Looping Integration With a Concentrating Solar Thermal System

This paper introduces a chemical-looping configuration integrated with a concentrating solar thermal (CST) system. The CST system uses an array of mirrors to focus sunlight, and the concentrated solar flux is applied to a solar receiver to collect and convert solar energy into thermal energy. The thermal energy then drives a thermal power cycle for electricity generation or provides an energy source to chemical processes for material or fuel production. Considerable interest in CST energy systems has been driven by power generation, with its capability to store thermal energy for continuous electricity supply or peak shaving. However, CST systems have other potential to convert solar energy into fuel or to support thermochemical processes. Thus, we introduce the concept of a chemical-looping configuration integrated with the CST system that has potential applications for thermochemical energy storage or solar thermochemical hydrogen production. The chemical-looping configuration integrated with a CST system consists of the following: a solar-receiver reactor for solar-energy collection and conversion, thermochemical energy storage, a reverse reactor for energy release, and system circulation. We describe a high-temperature reactor receiver that is a key component in the chemical-looping system. We also show the solar-receiver design and its performance analyzed by solar-tracing and thermal-modeling methods for integration within a CST system.

14 SOLAR ENERGY↗

Analysis of Solar Receiver Performance for Chemical-Looping Integration With a Concentrating Solar Thermal System

This paper introduces a chemical-looping configuration integrated with a concentrating solar thermal (CST) system. The CST system uses an array of mirrors to focus sunlight, and the concentrated solar flux is applied onto a solar receiver to collect and convert solar energy into thermal energy. The thermal energy then drives a thermal power cycle for electricity generation or provides an energy source to chemical processes for material or fuel production. Considerable interest in CST has been driven by power generation with its capability to store thermal energy for continuous electricity supply or peak shaving. However, CST systems have other potential to convert solar energy into fuel or support thermochemical processes. The chemical-looping configuration integrated with the CST system can be a platform for implementing various solar-thermochemical processes. The chemical-looping configuration integrated with a CST system has potential applications for thermochemical energy storage and solar thermochemical hydrogen production. To use the solar energy efficiently and effectively, a high-temperature reactor receiver is a key component in the chemical-looping system. This paper shows a novel planar-cavity receiver design and its performance analyzed by solar-tracing and thermal-modeling methods for solar integration in a CST system.

14 SOLAR ENERGY↗

Cusped light-like Wilson loops in gauge theories

We propose and discuss a new approach to the analysis of the correlation functions which contain light-like Wilson lines or loops, the latter being cusped in addition. The objects of interest are therefore the light-like Wilson null-polygons, the soft factors of the parton distribution and fragmentation functions, high-energy scattering amplitudes in the eikonal approximation, gravitational Wilson lines, etc. Our method is based on a generalization of the universal quantum dynamical principle by J. Schwinger and allows one to take care of extra singularities emerging due to lightlike or semi-light-like cusps. We show that such Wilson loops obey a differential equation which connects the area variations and renormalization group behavior of those objects and discuss the possible relation between geometrical structure of the loop space and area evolution of the light-like cusped Wilson loops.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗