Results for “Flow Conditions” — Page 38

NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper presents the results of an ongoing study into the linear stability characteristics of the boundary layer flow over the common research model with natural laminar flow (CRMNLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work involving parallel stability computations of a boundary layer flow based on the conical flow approximation has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien- Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. Here, we examine the effects of the simplifying approximations in both basic state computation and the stability analysis, with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, the basic states are computed by using full Navier-Stokes equations and the stability analysis is performed by using a nonorthogonal coordinate system that allows a clear distinction between planar TS and CF instabilities. Furthermore, the effects of curvature and nonparallel mean flow have been included in the stability computations based on the parabolized stability equations (PSE). The fully turbulent Reynolds-Averaged-Navier-Stokes (RANS) mean flow solutions show good agreement with the measured wall pressure distribution. Viscous-inviscid interactive effects are observed to be important because the shock fronts along the suction surface are influenced by the imposed transition front. The stability results confirm the previous findings related to TS amplification within the inboard region of the wing and the dominance of stationary CF modes in the outboard region. However, given the close proximity of the measured transition front and the dual shock system within the outer part of the wing, the onset of transition may well be shock limited within the outboard region. In general, the transition criterion based on the dual N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at Re MAC = 15 million and AoA = 1.5, 2 degrees; however, the low values of the correlating N-factors at Re MAC = 17.5 million support the hypothesis that the measured transition at the higher Reynolds number may have been strongly influenced by the merging of turbulent wedges that originate from surface imperfections near the leading edge.

Boundary layer transition↗

NASA NTRS2021

Transition Analysis for the CRM-NLF Wind Tunnel Configuration

This paper presents the results of an ongoing study into the linear stability characteristics of the boundary layer flow over the common research model with natural laminar flow (CRMNLF) aircraft configuration. The flow conditions match selected test conditions from a recent wind tunnel experiment in the National Transonic Facility at the NASA Langley Research Center. Previous work involving parallel stability computations of a boundary layer flow based on the conical flow approximation has shown that the measured onset of laminar-turbulent transition during the experiments can be correlated with the linear amplification of Tollmien- Schlichting (TS) and stationary crossflow (CF) instabilities in the swept wing boundary layer. Here, we examine the effects of the simplifying approximations in both basic state computation and the stability analysis, with the goal of quantifying the resulting changes in the N-factor correlations. Specifically, the basic states are computed by using full Navier-Stokes equations and the stability analysis is performed by using a nonorthogonal coordinate system that allows a clear distinction between planar TS and CF instabilities. Furthermore, the effects of curvature and nonparallel mean flow have been included in the stability computations based on the parabolized stability equations (PSE). The fully turbulent Reynolds-Averaged-Navier-Stokes (RANS) mean flow solutions show good agreement with the measured wall pressure distribution. Viscous-inviscid interactive effects are observed to be important because the shock fronts along the suction surface are influenced by the imposed transition front. The stability results confirm the previous findings related to TS amplification within the inboard region of the wing and the dominance of stationary CF modes in the outboard region. However, given the close proximity of the measured transition front and the dual shock system within the outer part of the wing, the onset of transition may well be shock limited within the outboard region. In general, the transition criterion based on the dual N-factor method with N TS = N CF = 6 is reasonably successful at correlating with the measured transition fronts at Re MAC = 15 million and AoA = 1.5, 2 degrees; however, the low values of the correlating N-factors at Re MAC = 17.5 million support the hypothesis that the measured transition at the higher Reynolds number may have been strongly influenced by the merging of turbulent wedges that originate from surface imperfections near the leading edge.

Boundary layer transition↗

NASA NTRS1992

Radiative energy transfer in molecular gases

Basic formulations, analyses, and numerical procedures are presented to study radiative interactions in gray as well as nongray gases under different physical and flow conditions. After preliminary fluid-dynamical considerations, essential governing equations for radiative transport are presented that are applicable under local and nonlocal thermodynamic equilibrium conditions. Auxiliary relations for relaxation times and spectral absorption models are also provided. For specific applications, several simple gaseous systems are analyzed. The first system considered consists of a gas bounded by two parallel plates having the same temperature. Within the gas there is a uniform heat source per unit volume. For this system, both vibrational nonequilibrium effects and radiation conduction interactions are studied. The second system consists of fully developed laminar flow and heat transfer in a parallel plate duct under the boundary condition of a uniform surface heat flux. For this system, effects of gray surface emittance are studied. With the single exception of a circular geometry, the third system is considered identical to the second system. Here, the influence of nongray walls is also studied.

Tiwari, Surendra N.↗

NASA NTRS1975

Transonic buffet behavior of Northrop F-5A aircraft

Flight tests were performed on an extensively instrumented F-5A aircraft to investigate the dynamic buffet pressure distribution on the wing surfaces and the responses during a series of transonic maneuvers called the windup turns. The maneuvers to maximum lift were performed at three Mach number-altitude combinations with a constant 'q' of approximately 14,360 N/sq m (300 psf). The fluctuating buffet pressure data at 24 stations on the right wing of the F-5A were acquired by miniaturized semiconductor type pressure transducers mounted on the wing. A new transducer mounting and wiring technique was applied where the interference with the natural flow condition was minimized. The data acquired in this manner were found adequate to trace the shock origin, the movement of the shock front and the development of the separated flow (shock induced or leading edge induced) on the wing surface.

Hwang, C.↗

NASA NTRS1975

Northrop F-5A aircraft transonic buffet pressure data acquisition and response analysis

Flight tests were performed on an extensively instrumented F-5A aircraft to investigate the dynamic buffet pressure distribution on the wing surfaces and the responses during a series of transonic maneuvers called the windup turns. The maneuvers were performed at three Mach number-altitude combinations with a constant q of approximately 14,360 N/sq m (300 psf). The fluctuating buffet pressure data at 24 stations on the right wing of the F-5A were acquired by miniaturized semiconductor type pressure transducers mounted on the wing. A new transducer mounting and wiring technique was applied where the interference with the natural flow condition was minimized. The data acquired in this manner were found adequate to trace the shock origin, the movement of the shock front and the development of the separated flow (shock-induced or leading-edge induced) on the wing surface. An analytical procedure, called a 'segmentwise stationary procedure', was introduced to compute the aircraft response spectra based on the measured buffet pressures. The analytical response data computed in this manner are correlated with the test response data obtained in the same flights.

Hwang, C.↗

NASA NTRS1993

Dynamic localization and second-order subgrid-scale models in large eddy simulations of channel flow

The objective here is to test the Dynamic Localization (DL) model in a wall-bounded channel flow for numerical stability and accuracy of results. Algebraic stress models suggest that the model for the residual subgrid-scale (SGS) Reynolds stress and scalar flux should generally have terms comprising most of the unique products of the resolved strain (S) and rotation (R) tensors with S and the resolved scalar gradient. The standard dynamic SGS model uses a simple (Smagorinsky) base model for the residual Reynolds stress, which is made proportional to S, and down-gradient base models for residual scalar fluxes; these correspond to the lowest, 'first-order' terms in algebraic stress models. Temporal scaling terms in these base models are formed from the magnitude of the resolved strain rate. While this is appropriate for simple shear flows, it may not be appropriate for more complicated flows (relevant to geophysical and astrophysical problems) that include any combination of shear, rotation, buoyancy, etc. On the other hand, the coefficient in the dynamic SGS model readily adjusts itself to different flow conditions and may adequately take account of these effects without the need for more complicated base models. Cabot (1993) has begun to test the dynamic SGS model in buoyant flows (Rayleigh-Benard and internally heated convection) with and without buoyancy terms explicitly included in the scaling terms of the base model; no great differences were found in large eddy simulation (LES) results for the different base model scalings. The second objective in this work is to test base models with additional, 'second-order' terms (e.g., S(sup 2) and RS for the residual Reynolds stress). These terms have been found to improve large-scale flow predictions by kappa-epsilon models in the presence of rotation and shear. Second-order base models will be tested here in the LES of channel flow with and without solid-body rotation and compared with results from the standard first-order base models to determine if there are significant differences or improvements in results that would warrant the added complexity of the second-order base models.

Cabot, William H.↗

NASA NTRS1988

Hypersonic blunt body computations including real gas effects

The recently developed second-order explicit and implicit total variation diminishing (TVD) shock-capturing methods of the Harten and Yee, Yee, and van Leer types in conjunction with a generalized Roe's approximate Riemann solver of Vinokur and the generalized flux-vector splittings of Vinokur and Montagne for two-dimensional hypersonic real gas flows are studied. A previous study on one-dimensional unsteady problems indicated that these schemes produce good shock-capturing capability and that the state equation does not have a large effect on the general behavior of these methods for a wide range of flow conditions for equilibrium air. The objective of this paper is to investigate the applicability and shock resolution of these schemes for two-dimensional steady-state hypersonic blunt body flows. The main contribution of this paper is to identify some of the elements and parameters which can affect the convergence rate for high Mach numbers or real gases but have negligible effect for low Mach number cases for steady-state inviscid blunt body flows.

Montagne, J.-L.↗

NASA NTRS1987

Remote noncontacting measurements of heat transfer coefficients for detection of boundary layer transition in wind tunnel tests

An infrared measurement system is used that consists of a laser heating source, an infrared camera for data acquisition, and a video recorder for data storage. A laser beam is scanned over an airfoil, heating its surface to a few degrees above ambient. An infrared camera then measures the temperature of the airfoil over a two-dimensional field, and these temperatures are stored as a function of time on a video recorder. The resulting temperature pictures are digitized and an iterative approximation algorithm is used to extract the heat transfer coefficient. The resulting values are normalized to the natural convection condition. The technique has been applied in low-speed wind tunnel tests and compared to well-established hot-film measurements which were made simultaneously to confirm the flow conditions. Heat transfer coefficients were determined using a linear scanning pattern, to indicate the position of natural and of artificially induced transition on an airfoil, at various wind speeds. The technique is shown to be sensitive to transition at low Mach numbers. The advantages of the technique are discussed.

Heath, D. Michele↗

NASA NTRS1989

Capabilities of wind tunnels with two-adaptive walls to minimize boundary interference in 3-D model testing

An initial wind tunnel test was made to validate a new wall adaptation method for 3-D models in test sections with two adaptive walls. First part of the adaptation strategy is an on-line assessment of wall interference at the model position. The wall induced blockage was very small at all test conditions. Lift interference occurred at higher angles of attack with the walls set aerodynamically straight. The adaptation of the top and bottom tunnel walls is aimed at achieving a correctable flow condition. The blockage was virtually zero throughout the wing planform after the wall adjustment. The lift curve measured with the walls adapted agreed very well with interference free data for Mach 0.7, regardless of the vertical position of the wing in the test section. The 2-D wall adaptation can significantly improve the correctability of 3-D model data. Nevertheless, residual spanwise variations of wall interference are inevitable.

Rebstock, Rainer↗

NASA NTRS1934

Investigation of a Rateau Supercharger for a 700-horsepower Airplane Engine

The Rateau supercharger investigated had, under normal operating conditions, an adiabatic efficiency of 52 percent, the CINA constant-pressure altitude being 6,240 m and the corresponding CINA compression ratio being 2.22. In order to understand the flow conditions in the supercharger, the air velocities at various points, the theoretical delivery heads and a few characteristics were calculated.

Oestrich, Hermann↗

NASA NTRS2019

The Effect of Incoming Boundary Layer Characteristics on the Performance of a Distributed Propulsion System

An experimental study is conducted in an effort to advance the understanding of flow physics associated with a boundary layer ingesting, distributed propulsion system. The influence of incoming boundary layer thickness and flow distortions are studied on the flow downstream and the overall performance of the system. The propulsion model, fabricated using additive manufacturing and integrated with electrical fans, is mounted on a flat plate and tested at subsonic speeds. Detailed characterization of the incoming boundary layer and subsequent assessment of the downstream flow field is performed using hotwire anemometry. Modification of the incoming boundary layer is achieved by placing tripping devices, such as rods and vortex generating ramps, near the leading edge of the flat plate. The overall performance of the system for different incoming flow conditions is analyzed by comparing magnitudes of exhaust velocities as well as estimated propulsive power to the corresponding baseline values. For a constant input power to the fans, smaller upstream flow distortions and moderately thickened boundary layers result in marginal changes in the flow field downstream. On the other hand, notable reductions in downstream flow velocities and propulsive power are observed in the case of a significantly thicker and/or distorted incoming boundary layer. It is hoped that this study will serve as a database for this technologically relevant flow field that has not been explored adequately before.

Propulsion↗

NASA NTRSDate not supplied

Simulation of Dust-Laden Flow in the DLR L2K Facility

An integrated CFD-particle trajectory code called US3D-DUST is used to simulate the dusty flow environments performed in the German Aerospace Center (DLR) L2K arcjet facility. The particle trajectory code uses a Lagrangian approach, where the particle trajectories through the shock layer can be computed using a set of coupled ordinary differential equations. The L2K experiments measured mass loss to flat-face shaped samples of the Norcoat-Liège thermal protection system material. The US3D-DUST simulations were able to reproduce particle velocity and stagnation point heating rate data. When applied to the L2K dusty flow conditions, the US3D-DUST predictions of mass loss due to particle impacts and surface recession rates over-predicted the experimental values. It is recommended to perform additional dusty flow tests in the L2Kto provide and improve the surface damage model for Norcoat-Liège.

Thermal protection systems↗

NASA NTRSDate not supplied

Transition prediction in hypersonic regime on complex geometries with RANS-based models

In the near future, RANS computations will continue to play a significant role in the design of hypersonic vehicles with complex geometries. Therefore, it is imperative to continue testing, benchmarking, and refining the RANS models. In the present study, we evaluate RANS-like, transport equations-based models for predicting laminar-turbulent transition over a full-scale scale model of the BOLT flight configuration that was tested in the CUBRC LENS-II wind tunnel test facility. Based on the availability of the experimental results, comparisons are made between computations from several pre-existing transition models and Computational Fluid Dynamics (CFD) codes, with an emphasis on using the same computational meshes and flow conditions for all computations. The analysis covers the sensitivity of the transition predictions to the input parameters for five different transition models (four mainstream models designed for low-speed flows and a uniquely high-speed model), grid resolution, and the details of model implementation across three different flow solvers. The results show that the phenomenological models can describe significant aspects of the measured transition front. However, a number of additional improvements are required before these models can offer more reliable estimates of transition in high-speed flows.

CFD↗

NASA NTRSDate not supplied

Transition Prediction in Hypersonic Regime on Complex Geometries With Rans-Based Models

In the near future, RANS computations will continue to play a significant role in the design of hypersonic vehicles with complex geometries. Therefore, it is imperative to continue testing, benchmarking, and refining the RANS models. In the present study, we evaluate RANS-like, transport equations-based models for predicting laminar-turbulent transition over a full-scale scale model of the BOLT flight configuration that was tested in the CUBRC LENS-II wind tunnel test facility. Based on the availability of the experimental results, comparisons are made between computations from several pre-existing transition models and Computational Fluid Dynamics (CFD) codes, with an emphasis on using the same computational meshes and flow conditions for all computations. The analysis covers the sensitivity of the transition predictions to the input parameters for five different transition models (four mainstream models designed for low-speed flows and a uniquely high-speed model), grid resolution, and the details of model implementation across three different flow solvers. The results show that the phenomenological models can describe significant aspects of the measured transition front. However, a number of additional improvements are required before these models can offer more reliable estimates of transition in high-speed flows.

CFD↗

NASA NTRSDate not supplied

Wall-Modeled Large-Eddy Simulations of Jet Noise in Flight Conditions

A campaign of wall-modeled large-eddy simulations (WMLES) using structured curvilinear overlapping grids has been performed with the Launch Ascent and Vehicle Aerodynamics (LAVA) computational fluid dynamics (CFD) software to predict jet noise for single-stream axisymmetric round jets. The simulations address the new Prediction Uncertainty Reduction (PUR) technical challenge within the context of NASA’s Commercial Supersonic Technology (CST) project. The focus of this effort is to generate a simulation database for single-stream axisymmetric round nozzles at several operating points both for static (no ambient co-flow), and in-flight (M ͚ =0.3 co-flow) conditions. The operating conditions range in jet exit Mach number from 0.38 to 1.1 with nozzle temperature ratios (NTR) from 0.84 to 2.7. The effect of the flight-stream on far-field noise sound spectra is assessed. Comparison of LES predictions to microphone array measurements demonstrate good agreement within the resolved frequency range. A dip in the predicted low frequency noise spectra for observers between 120° and 145° is observed. This dip is smaller for lower Mach numbers and seems to be correlated to the Mach wave radiation angle. The Mach 1.1 jet shows broadband-shock associated noise. While the onset of BBSN appears to be captured correctly in WMLES, some differences in its magnitude and the prominent frequency at which it occurs persist between the experiment and the simulations. The effect of the outer nozzle boundary layer state created by the co-flow is assessed and shows to be important for accurate comparisons with experiments. A change of 2.5dB between a slip-wall condition and a artificially thickened turbulent boundary layer was observed. In addition, simulations were performed with an alternative nozzle geometry that includes a internal plug and has twice the nozzle exit diameter. These two configurations resulted in very comparable spectra which is consistent with experimental observations. A generally stronger deviation from experimental results is observed for in-flight cases compared to static conditions. The applicability and correct usage of acoustic analogies used for far-field propagation with strong turbulent co-flows needs to be investigated more systematically using canonical problems to improve comparisons between experiments and WMLES. This is especially true for coherent noise sources seen in BBSN.

CST↗

NASA NTRS1948

Investigation of X24C-2 10-Stage Axial-Flow Compressor. III - Surge Characteristics

Compressor operation at low air flows for a given speed is limited by unstable flow conditions, commonly called surge. An investigation of surge in centrifugal compressors (reference 1) showed that the pulsation of pressures and velocities occurred when the slope of the compressor characteristic curve was positive and that the magnitude and frequency, as well as the incidence of surge, depended on the capacity and resistance of the total system. Although the theory presented in reference 1 is applicable to axial-floe compressors, little experimental information is available on the surge characteristics of the individual stages of axial-flow compressors, or on the variation of the surge characteristics with operating conditions. During the investigation to determine the performance of the X24C-2 compressor (references 2 and 3), instrumentation was added to study the surge characteristics and to determine the effect of speed and inlet pressure on the frequency, amplitude, and phase relation of the pressure pulsations behind each stage.

Buckner, Howard A., Jr.↗

NASA NTRS2002

Experimental Investigation of Separated and Transitional Boundary Layers Under Low-Pressure Turbine Airfoil Conditions

Modern low-pressure turbine airfoils are subject to increasingly stronger pressure gradients as designers impose higher loading in an effort to improve efficiency and to reduce part count. The adverse pressure gradients on the suction side of these airfoils can lead to boundary-layer separation, particularly under cruise conditions. Separation bubbles, notably those which fail to reattach, can result in a significant degradation of engine efficiency. Accurate prediction of separation and reattachment is hence crucial to improved turbine design. This requires an improved understanding of the transition flow physics. Transition may begin before or after separation, depending on the Reynolds number and other flow conditions, has a strong influence on subsequent reattachment, and may even eliminate separation. Further complicating the problem are the high free-stream turbulence levels in a real engine environment, the strong pressure gradients along the airfoils, the curvature of the airfoils, and the unsteadiness associated with wake passing from upstream stages. Because of the complicated flow situation, transition in these devices can take many paths that can coexist, vary in importance, and possibly also interact, at different locations and instances in time. The present work was carried out in an attempt to systematically sort out some of these issues. Detailed velocity measurements were made along a flat plate subject to the same nominal dimensionless pressure gradient as the suction side of a modern low-pressure turbine airfoil ('Pak-B'). The Reynolds number based on wetted plate length and nominal exit velocity, Re, was varied from 50;000 to 300; 000, covering cruise to takeoff conditions. Low, 0.2%, and high, 7%, inlet free-stream turbulence intensities were set using passive grids. These turbulence levels correspond to about 0.2% and 2.5% turbulence intensity in the test section when normalized with the exit velocity. The Reynolds number and free-stream turbulence level do not have a significant effect on the location of boundary-layer separation unless they are high enough to induce transition upstream of separation. The location and extent of the transition zone, in contrast, depend strongly on Re and TI. The beginning of reattachment closely follows the onset of transition. Under low free-stream turbulence conditions the boundary layer is laminar at separation and then begins to exhibit fluctuations in a finite frequency band in the shear layer over the separation bubble. These fluctuations are due to instability waves. The fluctuations grow in magnitude, higher harmonics are generated, and finally lead to a breakdown to turbulence. Transition begins in the shear layer, but quickly spreads to the near wall region and causes the boundary layer to reattach. The transition is rapid and the resulting turbulence contains a full range of high and low frequencies. Under high free-stream turbulence conditions, slowly growing low-frequency fluctuations are induced in the pretransitional boundary layer by the free-stream. The separation bubbles are considerably thinner than in the low TI cases, resulting in thinner boundary layers at the end of the test wall. At Re=50,000 and 100,000, the pre-transitional boundary layer separates at about the same location as in the low TI cases. Transition occurs through a bypass mode, begins upstream of the corresponding low-TI location, and proceeds in a manner similar to that of an attached boundary layer. Under high TI at Re=200,000 and 300,000, transition begins before separation. The boundary layer may separate, but if it does the separation bubble is very short and does not significantly affect the downstream development of the boundary layer. A comparison is made to previous work in a simulated cascade.

Hultgren, Lennart S.↗

NASA NTRS1978

Comparison of aerodynamic data measured in air and Freon-12 wind-tunnel test mediums

An experimental investigation was carried out to measure two dimensional static aerodynamic characteristics of a 65 sub l-213 airfoil in air and Freon-12 (dichlorodifluoromethane) test mediums at corresponding test conditions. The purpose of the tests was to compare measurements in the two test mediums and to evaluate reported methods of converting Freon-12 data to equivalent air values. The test article was a two dimensional wing instrumented to measure chordwise surface pressure distributions. The parameters considered were Mach numbers from 0.6 to 1.0, angles of attack of zero deg and 1 deg, and Reynolds numbers based on model chord from 2,000,000 to 21,000,000. The agreement between data measured in the two test mediums is further improved by application of the transonic or area ratio similarity laws. Where flow conditions are characterized by surface shocks or stall, the effects of flow separation may not be identically reflected in the Freon-12 data, even when converted in accordance with existing similarity laws.

Weller, W. H.↗