Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Finite Element Modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Crystal plasticity modeling of β phase deformation in Ti-6Al-4V

Ti-6Al-4V is an alloy of titanium that dominates titanium usage in applications ranging from mass-produced consumer goods to high-end aerospace parts. The material's structure on a microscale is known to affect its mechanical properties but these effects are not fully understood. Specifically, this work will address the effects of low volume fraction intergranular β phase on Ti-6Al-4V's mechanical response during the transition from elastic to plastic deformation. A crystal plasticity-based finite element model is used to fully resolve the deformation of the β phase for the first time. This high fidelity model captures mechanisms difficult to access via experiments or lower fidelity models. Lastly, the results are used to assess lower fidelity modeling assumptions and identify phenomena that have ramifications for failure of the material.

36 MATERIALS SCIENCE↗

Spectroscopic and Computational Analysis of Chemical Pollutants Interactions on Steel - 18409

There is limited understanding of the scientific interaction of the chemical contaminants to DOE facility materials which can alter the stability of the materials, affecting the general safety. The resulting studies will have a direct impact towards developing an enhanced cost-effective decontamination method and understanding the negative effects caused by the chemical waste on the structural integrity of the solid surface in contact. First order kinematic models provide a better fit to the experimental data, implying that one layer of Hg adsorbs to the steel surface. Energy dispersive X-ray analysis confirmed that stainless steel samples are mainly composed of Fe, Ni, and Cr, and have a low carbon content. Objective: To determine the physiochemical interactions of Mercury (Hg) and Cesium (Cs) to steel and concrete using spectroscopic, adsorption and computational studies. To develop a multiscale simulation that shows the effects of adsorption and diffusion of alkali metals on the mechanical performance of steel alloys used in nuclear power plants. Approach: Molecular Dynamics (MD) simulations were used to compute the stress gradient generated in steel due to Hg adsorption. Finite element models were developed for simulating the effects of temperature and pressure in a diffusion analysis. Based on experimental data, one layer of Hg was used for the MD simulations. Material properties at the atomic level were determined from the MD simulations The stress gradient from the MD simulations is used as an input parameter in the FE simulation. Conclusions and Future Work: Computational methods such as MD and FE simulations were used to determine the effects of mercury adsorption in stainless steel samples. The adsorption process induces a stress gradient in the facility materials, which can affect the mechanical performance of facility materials under service. Tensile stresses help the diffusion process while compressive have the opposite effect. Temperature has a positive effect in the mass diffusion process. Future work will evaluate the effects of temperature on the material properties at the molecular level using both experimental and MD methods. Future work will evaluate the mechanical performance of facility materials at a wide range of environmental variables.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A static analysis of three-dimensional functionally graded beams through hierarchical one-dimensional finite elements

In this paper, the static response of three-dimensional beams made of functionally graded materials is investigated through a family of hierarchical one-dimensional finite elements. A wide variety of elements is proposed differing by the kinematic formulation and the number of nodes per elements along the beam axis. Elements’ stiffness matrix and load vector are derived in a unified nuclear form that does not depend upon the a priori expansion order over the cross-section nor the finite element approximation along the beam axis. Results are validated towards three-dimensional finite element models as well as equivalent Navier-type analytical solutions. The numerical investigations show that accurate and efficient solutions (when compared with full three-dimensional FEM solutions) can be obtained by the proposed family of hierarchical one-dimensional elements’ family.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Novel application of the modal strain energy technique for state-of-the-art damping predictions

Structural damping, which measures the energy dissipation of a vibrating structure, is a key modeling input for lightweight structures but is notoriously hard to predict. This work utilizes vibration-based measurements of centimeter-scale coupons and the modal strain energy approach to predict structural damping of a lightly damped structure. The approach was originally validated with panels shorter than a meter in length. This work extends the validation to a 2.75 m beam made of unidirectional and biaxial glass fiber laminates bonded by adhesive. The comparison between three-dimensional finite element model predictions and full-scale experimental measurements of damping show an average error of 5.2% for the first five modes. Additionally, the modal strain energy approach is newly applied with a one-dimensional geometrically exact beam theory model and a two-dimensional sectional analysis solver. This beam approach accurately predicts the damping behavior of the first bending modes but loses accuracy for higher order modes that are dominated by three-dimensional effects. This novel approach provides faster simulations while allowing arbitrary beam cross sections. The paper also investigates traditional and high-force dynamic mechanical analysis to measure structural damping of coupons. Both alternatives show significant errors in attempted validation against the theoretical thermoelastic damping of aluminum coupons.

17 WIND ENERGY↗

Mechanical Design Studies of the MQXF Long Model Quadrupole for the HiLumi LHC

The Large Hadron Collider Luminosity upgrade (HiLumi) program requires new low-β triplet quadrupole magnets, called MQXF, in the Interaction Region (IR) to increase the LHC peak and integrated luminosity. The MQXF magnets, designed and fabricated in collaboration between CERN and the U.S. LARP, will all have the same cross section. The MQXF long model, referred as MQXFA, is a quadrupole using the Nb3Sn superconducting technology with 150 mm aperture and a 4.2 m magnetic length and is the first long prototype of the final MQXF design. The MQXFA magnet is based on the previous LARP HQ and MQXFS designs. In this paper we present the baseline design of the MQXFA structure with detailed 3D numerical analysis. A detailed tolerance analysis of the baseline case has been performed by using a 3D finite element model, which allows fast computation of structures modelled with actual tolerances. Tolerance sensitivity of each component is discussed to verify the actual tolerances to be achieved by vendors. In conclusion, tolerance stack-up analysis is presented in the end of this paper.

43 PARTICLE ACCELERATORS↗

Theoretical and experimental studies of combined therapy of tumours with application of ultrasound

The article presents novel method of combined therapy of superficial tumours based on excitation of ultrasonic waves in tumour tissues by means of ring-shaped waveguide with subsequent radiotherapy and results of its theoretical and experimental studies. Harmonic analysis of forced flexural vibration of the waveguide using ANSYS software and APDL (ANSYS Parametric Design Language) was implemented for determination of waveguide geometric parameters providing its resonance for the given excitation frequency. The developed finite element model accounts for interaction between the waveguide and tumour tissue as well as initial prestressing of tissue radially compressed by the waveguide. Resonant curves of the waveguide in terms of its thickness and diameter are calculated and presented. Experimental studies were performed in vivo on white rats with inoculated sarcoma M-1 tumours. Treatment was performed using ultrasound with frequency 22-23 kHz and intensity about 2 W/cm{sup 2}. Ultrasonic treatment was proved to be an efficient modifier of radiotherapy.

60 APPLIED LIFE SCIENCES↗

Meissner-London Susceptibility of Superconducting Right Circular Cylinders in an Axial Magnetic Field

Analysis of magnetic susceptibility of nonellipsoidal samples is a long-standing problem in experimental studies of magnetism and superconductivity. Here the quantitative description of the Meissner-London response (no Abrikosov vortices) of right circular cylinders in an axial magnetic field is given. Three-dimensional adaptive finite-element modeling is used to calculate the total magnetic moment ( m ) in a wide range of London penetration depth ( λ ) to sample size ( a ) ratios, λ /a. Furthermore, by fitting numerical solutions, the closed-form empirical magnetic susceptibility is obtained involving only sample dimensions and λ, thus providing a recipe for determining the London penetration depth from the precision measurements of the magnetic susceptibility. Detailed protocols of the experimental data analysis using the developed approach are given. The results can be readily extended to the most frequently used cuboid-shaped samples.

3-dimensional systems↗

Mechanical Modeling of a WIPP Drum Under Pressure

Mechanical modeling was undertaken to support the Waste Isolation Pilot Plant (WIPP) technical assessment team (TAT) investigating the February 14th 2014 event where there was a radiological release at the WIPP. The initial goal of the modeling was to examine if a mechanical model could inform the team about the event. The intention was to have a model that could test scenarios with respect to the rate of pressurization. It was expected that the deformation and failure (inability of the drum to contain any pressure) would vary according to the pressurization rate. As the work progressed there was also interest in using the mechanical analysis of the drum to investigate what would happen if a drum pressurized when it was located under a standard waste package. Specifically, would the deformation be detectable from camera views within the room. A finite element model of a WIPP 55-gallon drum was developed that used all hex elements. Analyses were conducted using the explicit transient dynamics module of Sierra/SM to explore potential pressurization scenarios of the drum. Theses analysis show similar deformation patterns to documented pressurization tests of drums in the literature. The calculated failure pressures from previous tests documented in the literature vary from as little as 16 psi to 320 psi. In addition, previous testing documented in the literature shows drums bulging but not failing at pressures ranging from 69 to 138 psi. The analyses performed for this study found the drums failing at pressures ranging from 35 psi to 75 psi. When the drums are pressurized quickly (in 0.01 seconds) there is significant deformation to the lid. At lower pressurization rates the deformation of the lid is considerably less, yet the lids will still open from the pressure. The analyses demonstrate the influence of pressurization rate on deformation and opening pressure of the drums. Analyses conducted with a substantial mass on top of the closed drum demonstrate that the drums will still open provided the pressure is high enough. Investigation teams should look for displaced drum lids when searching for drums that have pressurized and failed. The mechanical modeling study for this program is summarized in the following memo. Following a brief introduction, there is a summary of a brief literature review of previous pressure testing of drums, an explanation of the model, presentation of the key results, some discussion, and concluding with a summary and key points.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Simulating the effect of grain structure and porosity on creep for powder bed fusion 316H

This report details results from modeling studies focused on identifying the potential factors influencing creep performance of 316H stainless steel manufactured using Laser Powder Bed Fusion (LPBF), with a focus on experimentally-observed and predicted differences between the response of the AM material and conventionally manufactured wrought 316H. The studies presented here systematically look at the role of grain structure, porosity and texture in the anisotropic creep behavior of the material under conditions expected in high temperature advanced nuclear reactors. A physics-based Crystal Plasticity Finite Element modeling approach has allowed us to look at these factors in isolation and study their role in the material's long-term deformation behavior. An update to the precipitation model used in the constitutive framework for 316H is also presented here, with the aim of improving the accuracy of our results from this modeling effort. This work is a step in the direction of gaining mechanistic understanding of the long-term deformation behavior of LPBF 316H, helping us model its long term performance and reducing the qualification time for the material.

36 MATERIALS SCIENCE↗

First in-core simultaneous measurements of nuclear heating and thermal neutron flux obtained with the innovative mobile calorimeter CALMOS inside the OSIRIS reactor

Nuclear heating inside a MTR reactor has to be known in order to design and to run irradiation experiments which have to fulfill target temperature constraints. This measurement is usually carried out by calorimetry. The innovative calorimetric system, CALMOS, has been studied and built in 2011 for the 70 MWth OSIRIS reactor operated by CEA. Thanks to a new type of calorimetric probe, associated to a specific displacement system, it provides measurements along the fissile height and above the core. This development required preliminary modelling and irradiation of mock-ups of the calorimetric probe in the ex-core area, where nuclear heating rate does not exceed 2 W.g{sup -1}. The calorimeter working modes, the different measurement procedures allowed with such a new probe, the main modeling and experimental results and expected advantages of this new technique have been already presented. However, these first in-core measurements were not performed beyond 6 W.g{sup -1}, due to an inside temperature limitation imposed by a safety authority requirement. In this paper, we present the first in-core simultaneous measurements of nuclear heating and conventional thermal neutron flux obtained by the CALMOS device at the 70 MW nominal reactor power. For the first time, this experimental system was operated in nominal in-core conditions, with nominal neutron flux up to 2.7 10{sup 14} n.cm{sup -2}.s{sup -1} and nuclear heating up to 12 W.g{sup -1}. A comprehensive measurement campaign carried out from 2013 to 2015 inside all accessible irradiation locations of the core, allowed to qualify definitively this new device, not only in terms of measurement ability but also in terms of reliability. After a brief reminder of the calorimetric cell configuration and displacement system specificities, first nuclear heating distributions at nominal power are presented and discussed. In order to reinforce the heating evaluation, a systematic comparison is made between results obtained by different methods, the probe calibration coefficient and the zero method. Thermal neutron flux evaluation from the SPND signal processing required a specific TRIPOLI-4 Monte Carlo calculation which has been performed with the precise CALMOS cell geometry. In addition, the Finite Element model for temperatures map prediction inside the calorimetric cell has been upgraded with the recent experimental data obtained up to 12 W.g{sup -1}. The Kc coefficient, taking into account nonlinearities with regard to the calibration, has been reevaluated so as to make relevant measurements up to the nominal reactor power. Finally, the experience feedback acquired until now with this first CALMOS version led us to improvement perspectives. A second device is currently under manufacturing and main technical options chosen for this second version are presented. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Finite-element analysis of transverse compressive and thermal loads on Nb 3 Sn wires with voids

High-field superconducting magnets play a very important role in many large-scale physics experiments, particularly particle colliders and fusion confinement devices such as Large Hadron Collider (LHC) and International Thermonuclear Experimental Reactor (ITER). The two most common superconductors used in these applications are NbTi and Nb 3 Sn. Nb 3 Sn wires are favored because of their significantly higher J c (critical current density) for higher field applications. The main disadvantage of Nb 3 Sn is that the superconducting performance of the wire is highly strain sensitive and it is very brittle. This strain sensitivity is strongly influenced by two factors: plasticity and cracked filaments. Cracks are induced by large stress concentrators that can be traced to the presence of voids in the wire. We develop detailed 2-D and 3-D finite-element models containing wire filaments and different possible distributions of voids in a bronze-route Nb 3 Sn wire. We apply compressive transverse loads for various cases of void distributions to simulate the stress and strain response of a Nb 3 Sn wire under the Lorentz force. Furthermore, this paper improves our understanding of the effect voids have on the Nb 3 Sn wire's mechanical properties, and in so, the connection between the distribution of voids and performance degradation such as the correlation between irreversible strain limit and the void-induced local stress concentrations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Strain and lattice orientation distribution in SiN/Ge complementary metal–oxide–semiconductor compatible light emitting microstructures by quick x-ray nano-diffraction microscopy

This paper presents a study of the spatial distribution of strain and lattice orientation in CMOS-fabricated strained Ge microstripes using high resolution x-ray micro-diffraction. The recently developed model-free characterization tool, based on a quick scanning x-ray diffraction microscopy technique can image strain down to levels of 10{sup −5} (Δa/a) with a spatial resolution of ∼0.5 μm. Strain and lattice tilt are extracted using the strain and orientation calculation software package X-SOCS. The obtained results are compared with the biaxial strain distribution obtained by lattice parameter-sensitive μ-Raman and μ-photoluminescence measurements. The experimental data are interpreted with the help of finite element modeling of the strain relaxation dynamics in the investigated structures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural Characterization of a Toppling Rock Slab From Array-Based Ambient Vibration Measurements and Numerical Modal Analysis

Accurate assessments of the internal structure and boundary conditions of unstable rock slopes are imperative for evaluating landslide hazard scenarios. However, instability characterization at depth remains challenging and is often limited by costly or invasive subsurface investigations. Here, we develop a new approach coupling array-based ambient vibration modal analysis and numerical modeling to improve structural characterization of rock slope instabilities at depth. We used ambient noise cross-correlation on 4 hr of seismic data recorded by an array of 30 nodal geophones at a 500-m-long toppling rock slab in Utah, USA to identify modal frequencies between 0.8 and 3.5 Hz and derive modal displacements. We show that transverse and longitudinal bending modes span the length of the instability, indicating an interconnected slab. Further, statistical comparison of field results with outputs from >1,000 finite element models with varying boundary conditions showed that the instability depth varies between 40–70 and 10–20 m in the middle and lateral regions, respectively. Our approach yields new information on the structural conditions of rock cliff and column instabilities at depth, which is not easily obtained by other means but is imperative for change detection monitoring and improved hazard assessments.

58 GEOSCIENCES↗

Thermoelectric power generator module of 16x16 Bi{sub 2}Te{sub 3} and 0.6%ErAs:(InGaAs){sub 1-x}(InAlAs){sub x} segmented elements

We report the fabrication and characterization of thermoelectric power generator modules of 16x16 segmented elements consisting of 0.8 mm thick Bi{sub 2}Te{sub 3} and 50 {mu}m thick ErAs:(InGaAs){sub 1-x}(InAlAs){sub x} with 0.6% ErAs by volume. An output power up to 6.3 W was measured when the heat source temperature was at 610 K. The thermoelectric properties of (InGaAs){sub 1-x}(InAlAs){sub x} were characterized from 300 up to 830 K. The finite element modeling shows that the performance of the generator modules can further be enhanced by improving the thermoelectric properties of the element materials, and reducing the electrical and thermal parasitic losses.

36 MATERIALS SCIENCE↗

Colocalized Raman spectroscopy – scanning electrochemical microscopy investigation of redox flow battery dialkoxybenzene redoxmer degradation pathways

Non-aqueous redox flow batteries offer high voltages for grid-level energy storage technologies. However, decomposition of the redoxmers - redox-active molecules that make up the anolyte and catholyte in the negative and positive cell compartments - is an important challenge to overcome for long-term storage. Here, we present a spectroelectrochemical study of the catholyte candidate 2,3-dimethyl-1,4-dialkoxybenzene (C7) and its decomposition mechanisms in the presence of a model nucleophilic base, pyridine. We utilize colocalized Raman microscopy and scanning electrochemical microscopy (Raman-SECM) to quantify the chemical rates of decom-position and qualitatively identify the reaction intermediates and products. A detailed study on how the Raman-SECM parameters (electrode distance, substrate electrode, and laser focal height) influence the Raman signal of the charged catholyte C7 ∙+ is presented. Using optimized conditions, we monitored the deprotonation of C7 ∙+ via Raman spectroscopy and the subsequent hydrogen abstraction from solvent molecules to regenerate C7 via electrochemistry. Finite element modeling was used to fit electrochemical and spectroscopic data, quantifying the deprotonation rates as k dep = 2000 and 700 L mol -1 s -1 and abstraction rates as k abs = 0.5 and 0.2 s - 1 in propylene carbonate and acetonitrile solvents, respectively. Our results show the value of spatiotemporal reso-lution in evaluating the chemical and electrochemical behavior of materials for redox flow batteries.

25 ENERGY STORAGE↗

Mechanical Performance of the First Two Prototype 4.5 m Long Nb$_3$Sn Low-$β$ Quadrupole Magnets for the Hi-Lumi LHC Upgrade

The U.S. High-Luminosity LHC Accelerator Upgrade Project (HL-LHC AUP) team is collaborating with CERN in the design and fabrication of the first 4.5 m long MQXFA magnets, a 150 mm aperture high-field Nb$_3$Sn quadrupole magnet that uses the aluminum shell-based bladder-and-key technology. The first two prototype magnets, MQXFAP1 and MQXFAP2, were assem-bled and tested while the first pre-series structure (MQXFA03) was in fabrication. This paper summarizes the mechanical perfor-mance of these prototype structures based on the comparison of measured strain gauge data with finite element model analyses from all load steps to powering. The MQXFAP1 magnet almost reached ultimate current before a short to ground was detected and the test was stopped. The MQXFAP2 magnet experienced a low training performance due to a fractured aluminum shell. MQXFAP1b was rebuilt with a new replacement coil, but an old coil limited the magnet from achieving the ultimate current. The mitigations and analyses of these prototype magnets are discussed in the context of the transition to pre-series production.

43 PARTICLE ACCELERATORS↗

Surface orientation ambiguity for single molecules at dielectric interfaces

Fluorescent molecules emit light in a dipole radiation pattern that can be used to infer their orientation through defocused fluorescence microscopy. Proper measurement of the orientation requires mathematical modeling of the radiation pattern expected for a dipole in the geometry of interest and subsequent comparison against experimental data. We point out an ambiguity in common calculations of these patterns that appears to compromise orientation measurements for molecules that are especially near dielectric surfaces. This results in a rotation of the measured emission dipole toward the surface for near-interface molecules, which can be mistaken for a preferentially horizontal orientation among the emitters. The proper treatment for on-surface emitters requires consideration of finite-sized current elements between two dielectric media, and we show that the theoretical ambiguity can be lifted via finite-element modeling. A prescription is provided for correcting measured orientations at arbitrary interfaces.

Dey, E. [University of Texas, Arlington, TX (Unite↗

ASSESSMENT OF RESIDUAL STRESSES ON U10MO ALLOY BASED MONOLITHIC MINI-PLATES DURING HOT ISOSTATIC PRESSING

This article presents an assessment of the residual stress field on U10Mo alloy based monolithic fuel plates and their elasto-plastic response to the thermo-mechanical fabrication process. Monolithic plate-type fuel for research and test reactors is a new fuel form proposed and developed by Idaho National Laboratory (INL) to accomplish higher uranium densities in the reactor core and allow multi-fold reduction of fuel enrichment. Identification of the 3D residual field is critical for benchmarking the new design and understanding the overall performance of the new plate-type fuels. To define fuel-cladding stress-strain characteristics, a new thermo-mechanical finite element model was developed. Material properties at high temperatures and material plasticity were considered carefully to improve the accuracy as the Hot Pressing temperature reaches the melting temperature of the cladding material. By using elasto-thermo-plastic material models, it was determined that the cladding material (AL6061-TO) is exposed to tensile stress field and exceeds its proportional limits, while the fuel foil (U10Mo) is under compression and remains below its yield limit. It was shown that the residual stresses would govern the overall behavior of the plates, and therefore, should not be neglected. In particular, the simulations have revealed the existence of stress gradients at the fuel/cladding interface, thus emphasizing the necessity of excellent bonding quality at the bond region for mechanical endurance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗