Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLOW VELOCITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Using Ensemble Data Assimilation to Estimate Transient Hydrologic Exchange Flow Under Highly Dynamic Flow Conditions

Abstract Quantifying dynamic hydrologic exchange flows (HEFs) within river corridors that experience high‐frequency flow variations caused by dam regulations is important for understanding the biogeochemical processes at the river water and groundwater interfaces. Heat has been widely used as a tracer to infer steady‐state flow velocities through analytical solutions of heat transport defined by the diurnal temperature signals. Under sub‐daily dynamic flow conditions, however, such analytical solutions are not applicable due to the violation of their fundamental assumptions. In this study, we developed a data assimilation‐based approach to estimate the sub‐daily flux under highly dynamic flow conditions using multi‐depth temperature observations at a 5‐min resolution. If the hydraulic gradient is measured, Darcy's law was used to calculate the flux with permeability estimated from temperature responses below the riverbed. Otherwise, flux was estimated directly by assimilating multi‐depth temperature data at 1‐ or 2‐hr time intervals assuming one‐dimensional flow and heat transport governing equation. By comparing estimated fluxes with model‐generated synthetic truth, we demonstrated that both schemes have robust performance in estimating fluxes under highly dynamic flow conditions. This data assimilation‐based flux estimation method was able to capture the vertical sub‐daily fluxes using multi‐depth high‐resolution temperature data alone, even in the presence of multi‐dimensional flow. This approach has been successfully applied to real field temperature data collected at the Hanford site, which experiences highly dynamic HEFs. Our study shows the promise of adopting distributed 1‐D temperature monitoring to capture spatial and temporal exchange dynamics in river corridors at a watershed scale or beyond.

54 ENVIRONMENTAL SCIENCES↗

Experimental study of combustion in a turbulent free shear layer formed at a rearward facing step

A premixed propane-air flame is stabilized in a turbulent free shear layer formed at a rearward facing step. The mean and rms averages of the turbulent velocity flow field are determined by LDV for both reacting (equivalence ratio 0.57) and nonreacting flows (Reynolds number 15,000-37,000 based on step height). The effect of combustion is to shift the layer toward the recirculation zone and reduce the flame spread. For reacting flow, the growth rate is unchanged except very near the step. The probability density function of the velocity is bimodial near the origin of the reacting layer and single-peaked but often skewed elsewhere. Large-scale structures dominate the reacting shear layer. Measurements of their passing frequency from LDV are consistent with high-speed Schlieren movies of the reacting layer and indicate that the coalescence rate of the eddies in the shear layer is reduced by combustion.

Pitz, R. W.↗

Plasma regimes in the deep geomagnetic tail - ISEE 3

The spacecraft remained close to or within a previously unexplored part of the distant (60-220 earth radii) geomagnetic tail nearly continuously from January 1 to March 30, 1983. Analysis of the data reveals that all of the plasma regimes identified previously with near-earth measurements (plasma sheet, low-latitude boundary layer, plasma mantle, lobe, and magnetosheath) remain recognizable in the distant tail. These regimes, however, are found to be intermingled in a more chaotic fashion than near the earth. Within the plasma sheet at approximately 200 earth radii, typical flow velocities are about 500 km/s tailward, considerably higher than in the near-earth plasma sheet. Earthward flow within the plasma sheet is observed occasionally, indicating the temporary presence of a neutral line beyond 220 earth radii. Also found are strong bidirectional electron anisotropies throughout much of the distant plasma sheet, boundary layer, and magnetosheath.

Bame, S. J.↗

A Critical Assessment of Protein Crystal Growth in Microgravity

Experiments to grow higher diffraction quality protein crystals in the microgravity environment of an orbiting spacecraft are one of the most frequently flown space experiments. Ground-based research has shown that convective flows occur even about protein crystals growing in the Earth's gravitational field. Further, this research has shown that the resultant flow velocities can cause growth cessation, and probably affect the measured X-ray data quality obtained. How flow deleteriously affects protein crystal growth (PCG) is still not known, and is the subject of ongoing research. Failing a rational method for ameliorating flow effects on Earth, one can, through NASA and other nations space agency sponsored programs, carry out protein crystal growth in the microgravity environment of an orbiting spacecraft. Early first generation PCG hardware was characterized by a very low success rate and a steep design learning curve. Subsequent hardware designs have improved upon their predecessors. Now the crystal grower has a wide variety of hardware configurations and crystal growth protocols to choose from, many of which implement "standard" laboratory protein crystal growth methods. While many of these are first or early second generation hardware the success rate, defined as growing crystals giving data better than has been obtained on Earth, is at least 20% overall and may be considerably higher if one only considers latter experiments. There are a large number of protein crystals grown every year, with hundreds of structures determined. Those crystallized in microgravity represent a small proportion of this total, and there is concern that the costs of the microgravity PCG program(s) do not justify such limited returns. Empirical evidence suggests that optimum crystal growth conditions in microgravity differ from those determined on Earth, further exacerbating the chances of success. Microgravity PCG is probably best suited for "mature" crystallizations, where one has considerable experience with the particular macromolecular system and has reached an apparent limit in diffraction resolution. Under such circumstances the cost of one or two successful flight experiments may more than offset the equivalent cost of several years effort to obtain the same improvement in data quality.

Pusey, Marc↗

Ignition of n-heptane pool by heated stagnating oxidizing flow

The ignition temperature of a liquid pool of n-heptane by heated oxidizer in a stagnation flow was experimentally determined for system pressures of 0.61-3 atm and pressure-weighted strain rates of 60-350 s{sup -1}. The surface of the liquid pool was maintained at a fixed location through continuous replenishment. The state of ignition was brought about, and monitored, by gradually increasing the oxidizer temperature. The strain rate was determined by seeding and measuring the oxidizer flow velocity using laser Doppler velocimetry (LDV). Computational simulation of the ignition event with detailed chemistry and transport was conducted by using a stagnation-flow code. The kinetic mechanisms utilized are a high-temperature n-heptane oxidation model, with 130 species and 955 reactions, and a reduced one of 58 species derived from a detailed mechanism of 561 species and 2539 reactions. The former mechanism yielded better agreement with the experimental measurements in general over the conditions examined. It was also found that the mole fraction of n-heptane at the interface changed only slightly with pressure and strain rate, and can be considered to have minimal effect on the ignition responses studies herein. A recently developed explosive mode analysis (EMA) was conducted to identify the controlling radicals and reactions in the non-premixed ignition of n-heptane. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Numerical investigation on two-fluid model (micropolar-Newtonian) for pulsatile flow of blood in a tapered arterial stenosis with radially variable magnetic field and core fluid viscosity

In the present study, an unsteady two-fluid model of blood through a tapered arterial stenosis with variable viscosity in the presence of variable magnetic field has been investigated. In this model, blood in the core region is assumed to be micropolar and plasma in the peripheral layer as Newtonian. Finite difference method is employed in solving the governing equations. The solutions for velocity, flow rate, wall shear stress and flow resistance are computed numerically. A comparison between the velocity profiles obtained by the present study and the experimental data is made and a good agreement between them is found. The model is used to study the effect of parameters such as taper angle, radially variable viscosity, hematocrit, the coupling number, the micropolar parameter, magnetic field and plasma layer thickness on physiologically important parameters such as wall shear stress distribution in the stenotic region and flow resistance. The results in the case of constant magnetic field and variable magnetic field are compared to study the effects of magnetic field on the flow of blood. It is found that the magnitudes of wall shear stress and flow resistance are higher in the case of variable magnetic field. It is important to note that the flow resistance is higher for magneto-micropolar fluid than the micropolar fluid. The wall shear stress decreases with increasing hematocrit parameter whereas flow resistance increases with hematocrit when the applied pressure gradient is held fixed. The model clearly shows the situation of a patient with a tapered arterial stenosis under feverish condition. Due care has been taken to compare the present theoretical results with the existing ones including experimental results and good agreement between them has been observed both qualitatively and quantitatively.

42 ENGINEERING↗

Nonlinear kinetic simulation study of the ion–ion streaming instability in single- and multi-ion species plasmas

The nonlinear evolution of the ion–ion streaming instability (IISI) is studied using numerical techniques novel to this problem that afford direct insight into the evolution of the particle distributions of each species. Here, during the linear phase of the instability, we demonstrate quantitative agreement with linear kinetic theory. Subsequently, the electrostatic field generated by the IISI causes ring-like velocity distributions of ions to form that are both heated and slowed to varying degrees relative to their initial flows. Due to variation in the trapping conditions for ion species of differing charge-to-mass ratio, when flows of multiple species interact, the nonlinear evolution of each species can be starkly different: we show a case where a lighter ion species is completely stopped by a heavier ion species via the IISI alone (i.e., without collisions) and, for the first time, demonstrate how the IISI can introduce a relative flow between ion species that initially have the same flow velocities, thereby separating them.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Radial Flows in Supergranules

We determine the radial component of the supergranular flow velocity by examining the center-to-limb variation of the Doppler velocity signal. We acquire individual Doppler images obtained with the MDI instrument on the SOHO spacecraft and process them to remove the p-mode oscillation signal, the axisymmetric flows, the convective blueshift signal, and instrumental artifacts. The remaining Doppler signal contains only cellular flow structures. The Doppler signal from the horizontal flows in these cells varies like sin p, where p is the heliocentric angle from disk center. The Doppler signal from radial flows varies like cos p. We fit the center-to-limb variation of the mean squared velocity signal to a straight line in sin(exp 2) rho over the central portion of the disk. The intercept of this line at disk center gives the amplitude of the radial component of the flow. The slope of the line gives the amplitude of the horizontal component. We find that the radial flows for typical supergranules have speeds about 10% that of their associated horizontal flows or about 30 m/s. The ratio of the radial to horizontal flow speed increases from 9% to about 18% as the size of the cells decreases from > 60 Mm to approximately 5 Mm. We use data simulations to check these results and find a ratio that increases from 5% to only about 12% over the same range of cell sizes. These smaller ratios are attributed to an underestimation of the horizontal flow speeds due to the fact that, the transverse component of the horizontal flow is not detected by the Doppler measurements.

Hathaway, D. H.↗

Satellite Remote Sensing Estimation of River Discharge: Application to the Yukon River Alaska

A methodology based on general hydraulic relations for rivers has been developed to estimate the discharge (flow rate) of rivers using satellite remote sensing observations. The estimates of discharge, flow depth, and flow velocity are derived from remotely observed water surface area, water surface slope, and water surface height, and demonstrated for two reaches of the Yukon River in Alaska, at Eagle (reach length 34.7 km) and near Stevens Village (reach length 38.3 km). The method is based on fundamental equations of hydraulic flow resistance in rivers, including the Manning equation and the Prandtl-von Karman universal velocity distribution equation. The method employs some new hydraulic relations to help define flow resistance and height of the zero flow boundary in the channel. Estimates are made both with and without calibration. The water surface area of the river reach is measured by using a provisional version of the U.S. Geological Survey (USGS) Landsat based product named Dynamic Surface Water Extent (DSWE). The water surface height and slope measurements require a self-consistent datum, and are derived from observations from the Jason-2 satellite altimeter mission. At both reach locations, the Jason-2 radar altimeter non-winter heights consistently tracked the stage recorded at USGS streamgages with a standard deviation of differences (error) during the non-winter periods of less than 7%. Part of the error may be due to differences in the gage and altimeter crossing locations with respect to the range of stage change and the response to changes in discharge at the upstream and downstream locations. For the non-winter periods, the radar derived slope estimates (mean = 0.0003) were constant over the mission lifetime, and in agreement with previously measured USGS water surface slopes and slopes determined from USGS topographic maps. The accuracy of the mean of the uncalibrated daily estimates of discharge varied between reaches, ranging from 13% near Stevens Village (N = 90) to −21% at Eagle (N = 246) based on the absolute error, and 5% to −6% based on the error of the log of the estimates. Calibrating to the mean of USGS daily discharge estimates from the streamflow rating for the same period of record at each streamgage resulted in mean absolute errors ranging from 1% to 2%, and log errors ranging from 1% or less. The error pattern of the estimates shows that without calibration, even though the mean is well simulated, the high and low end values over the range of estimates may have significant bias.

Bjerklie, David M.↗

Expansion Behavior and Temperature Mapping of Thermites in Burn Tubes as a Function of Fill Length [Thermal Imaging of Thermite Flame Propagation]

The reaction of loosely-packed aluminum/copper oxide (Al/CuO) thermites in a 12 cm long acrylic burn tube was investigated as a function of the fill length from 2 to 10 cm. The velocity of the luminous front was measured both in the filled and unfilled region, and approached 1000 m s-1 in the unfilled region, independent of the fill length. This value is approximately a factor of two higher than the fastest velocity measured in the filled region, 606 m s-1, for the 10 cm filled tube. The velocity increase in the unfilled region ist likely due to the increased open porosity, which can support faster flow velocities for a given pressure gradient relative to that in the porous material. A high-speed color imaging pyrometer was used to thermally map the evolution of the flame in both regions. Near the luminous front in the filled section, the temperature was observed to rapidly increase in a 1–2 cm zone to a maximum value near 3200 K, and an average value near 3000 K was sustained in the wake well after the front passes and exits the tube. In partially-filled tubes, even for the lowest fill length of 2 cm, the intermediate and/or product species could be seen to expand forward and completely fill the tube with a sustained temperature of ca. 3000 K. This temperature did not decay during the expansion, suggesting that the material continues to react as it expands. The results raise several questions about what a burn tube experiment is really measuring; such as what fraction of the material has burned when the luminous front passes and what role open cracks or microstructures play in promoting transport. Lastly, these questions are critically important towards developing a predictive capability for confined, loosely packed deflagrations.

36 MATERIALS SCIENCE↗

The Potential of Computational Fluid Dynamics Simulation on Serial Monitoring of Hemodynamic Change in Type B Aortic Dissection

PurposeWe aimed to assess the potential of computational fluid dynamics simulation (CFD) in detecting changes in pressure and flow velocity in response to morphological changes in type B aortic dissection.Materials and MethodsPressure and velocity in four morphological models of type B aortic dissection before and after closure of the entry tear were calculated with CFD and analyzed for changes among the different scenarios. The control model (Model 1) was patient specific and built from the DICOM data of CTA, which bore one entry tear and three re-entry tears. Models 2–4 were modifications of Model 1, with two re-entry tears less in Model 2, one re-entry tear more in Model 3, and a larger entry tear in Model 4.ResultsThe pressure and velocity pertaining to each of the morphological models were unique. Changes in pressure and velocity findings were accountable by the changes in morphological features of the different models. There was no blood flow in the false lumen across the entry tear after its closure, the blood flow direction across the re-entry tears was reversed after closure of the entry tear.ConclusionCFD simulation is probably useful to detect hemodynamic changes in the true and false lumens of type B aortic dissection in response to morphological changes, it may potentially be developed into a non-invasive and patient-specific tool for serial monitoring of hemodynamic changes of type B aortic dissection before and after treatment.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Liquid crystal torons in Poiseuille-like flows

Three-dimensional (3D) simulations of the structure of liquid crystal (LC) torons, topologically protected distortions of the LC director field, under material flows are rare but essential in microfluidic applications. Here, we show that torons adopt a steady-state configuration at low flow velocity before disintegrating at higher velocities, in line with experimental results. Furthermore, we show that under partial slip conditions at the boundaries, the flow induces a reversible elongation of the torons, also consistent with the experimental observations. These results are in contrast with previous simulation results for 2D skyrmions under similar flow conditions, highlighting the need for a 3D description of this LC soliton in relation to its coupling to the material flow. These findings pave the way for future studies of other topological solitons, like hopfions and heliknotons, in flowing soft matter systems.

Science & Technology - Other Topics↗

Note: Flowing ion population from a resonance cavity source

The experimental low energy plasma for hemispherical analyzers nominal testing thermal plasma facility of Dartmouth College uses a microwave plasma source which generates an ionosphere-like plasma through a two-step process. The plasma is initially generated inside a cylindrical, insulated, resonance cavity. This initial plasma must pass through a sheath in order to enter the main experimental region. This process imparts a significant flow velocity to the ions which has been neglected in previous analysis of this plasma source. We predict the flow energy of the ions to be between 12-15 eV depending on conservation laws and show agreement with experimental results.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Shear flow aerodynamics - Lifting surface theory

A lifting surface theory based on a parallel shear flow model is presented for steady, incompressible flows. The theory is intended to account approximately for the presence of a boundary layer. The method of Fourier transforms is used to calculate the pressure on a surface of infinite extent and arbitrary contour. Immediately above the surface is a region of sheared flow (the boundary layer), outside of which the flow velocity is constant. The Fourier transform of the pressure on this surface is used to derive the shear flow equivalent to the kernel function of classical potential flow lifting surface theory. The kernel function provides an integral relation between the upwash at a given point on the surface and the pressure everywhere on the surface. This relation is treated as an integral equation for the pressure, and is solved numerically. Computations are presented for the lift and pitching moment on a flat plate in two-dimensional flow, and for flat, rectangular wings of aspect ratio 1, 2, and 5. As expected, the shear layer decreases the lift curve slope; however, the shear layer (whose thickness is constant along the wing chord) has little effect on the center of pressure.

Ventres, C. S.↗

Interaction between a normal shock wave and a turbulent boundary layer at high transonic speeds. Part 1: Pressure distribution. Part 2: Wall shear stress. Part 3: Simplified formulas for the prediction of surface pressures and skin friction

An asymptotic description is derived for the interaction between a shock wave and a turbulent boundary layer in transonic flow, for a particular limiting case. The dimensionless difference between the external flow velocity and critical sound speed is taken to be much smaller than one, but large in comparison with the dimensionless friction velocity. The basic results are derived for a flat plate, and corrections for longitudinal wall curvature and for flow in a circular pipe are also shown. Solutions are given for the wall pressure distribution and the shape of the shock wave. Solutions for the wall shear stress are obtained, and a criterion for incipient separation is derived. Simplified solutions for both the wall pressure and skin friction distributions in the interaction region are given. These results are presented in a form suitable for use in computer programs.

Adamson, T. C., Jr.↗

Shock-free configurations in two-and three-dimensional transonic flow

Efforts to replace Sobieczky's complicated analog computations of solutions to the hodograph equations by a fast elliptic solver in order to generate shock-free airfoil designs more effectively are described. The indirect design of airfoil and wing shapes that are free from shock waves even though the local flow velocity exceeds the speed of sound is described. The problem of finding an airfoil in two dimensional, irrotational flow that has a prescribed pressure distribution is as addressed. Sobieczky's suggestion to use a fictitious gas for finding shock-free airfoils directly in the physical plane was the basis for a more efficient procedure for achieving the same end.

Seebass, A. R.↗

Development of a spinning wave heat engine

A theoretical analysis and an experimental investigation were conducted to assess the feasibility of developing a spinning wave heat engine. Such as engine would utilize a large amplitude traveling acoustic wave rotating around a cylindrica chamber, and it should not suffer from the inefficiency, noise, and intermittent thrust which characterizes pulse jet engines. The objective of this investigation was to determine whether an artificially driven large amplitude spinning transverse wave could induce a steady flow of air through the combustion chamber under cold flow conditions. In the theoretical analysis the Maslen and Moore perturbation technique was extended to study flat cylinders (pancake geometry) with completely open side walls and a central opening. In the parallel experimental study, a test moel was used to determine resonant frequencies and radial pressure distributions, as well as oscillatory and steady flow velocities at the inner and outer peripheries. The experimental frequency was nearly the same as the theoretical acoustic value for a model of the same outer diameter but without a central hole. Although the theoretical analysis did not predict a steady velocity component, simulaneous measurements of hotwire and microphone responses have shown that the spinning wave pumps a mean flow radially outward through the cavity.

Zinn, B. T.↗