Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “F STACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Test results of a 60 volt bipolar nickel-hydrogen battery

In July 1986, a high-voltage nickel-hydrogen battery was assembled at the NASA Lewis Research Center. This battery incorporated bipolar construction techniques to build a 50-cell stack with approximately 1.0 A-hr capacity (C) and an open-circuit voltage of 65 V. The battery was characterized at both low and high current rates prior to pulsed and nonpulsed discharges. Pulse discharges at 5 and 10 C were performed before placing the battery on over 1400, 40-percent depth-of-discharge, low-earth-orbit cycles. The successful demonstration of a high-voltage bipolar battery in one containment vessel has advanced the technology to where nickel-hydrogen high-voltage systems can be constructed of several modules instead of hundreds of individual cells.

Cataldo, Robert L.↗

Miniature Piezoelectric Macro-Mass Balance

Mass balances usually use a strain gauge that requires an impedance measurement and is susceptible to noise and thermal drift. A piezoelectric balance can be used to measure mass directly by monitoring the voltage developed across the piezoelectric balance, which is linear with weight or it can be used in resonance to produce a frequency change proportional to the mass change (see figure). The piezoelectric actuator/balance is swept in frequency through its fundamental resonance. If a small mass is added to the balance, the resonance frequency shifts down in proportion to the mass. By monitoring the frequency shift, the mass can be determined. This design allows for two independent measurements of mass. Additionally, more than one sample can be verified because this invention allows for each sample to be transported away from the measuring device upon completion of the measurement, if required. A piezoelectric actuator, or many piezoelectric actuators, was placed between the collection plate of the sampling system and the support structure. As the sample mass is added to the plate, the piezoelectrics are stressed, causing them to produce a voltage that is proportional to the mass and acceleration. In addition, a change in mass delta m produces a change in the resonance frequency with delta f proportional to delta m. In a microgravity environment, the spacecraft could be accelerated to produce a force on the piezoelectric actuator that would produce a voltage proportional to the mass and acceleration. Alternatively, the acceleration could be used to force the mass on the plate, and the inertial effects of the mass on the plate would produce a shift in the resonance frequency with the change in frequency related to the mass change. Three prototypes of the mass balance mechanism were developed. These macro-mass balances each consist of a solid base and an APA 60 Cedrat flextensional piezoelectric actuator supporting a measuring plate. A similar structure with 3 APA 120 Cedrat flextensional piezoelectric actuators spaced equidistantly at 120 degrees supporting the plate and a softer macro balance with an APA 150 actuator/sensor were developed. These flextensional actuators were chosen because they increase the sensitivity of the actuator to stress, allow the piezoelectric to be pre-stressed, and the piezoelectric element is a stacked multilayer actuator, which has a considerably lower input impedance than a monolithic element that allows for common instruments (e.g., input impedance of 10 megohms) to measure the voltage without rapidly discharging the charge/voltage on the piezoelectric actuator.

Sherrit, Stewart↗

Suppression of the valence transition in solution-grown single crystals of Eu 2 Pt 6 Al 15

Here, the study of Eu intermetallic compounds has allowed the exploration of valence fluctuations and transitions in 4⁢𝑓 electron systems. Recently, a Eu 2 ⁢Pt 6 ⁢Al 15 phase synthesized by arc-melting followed by a thermal treatment was reported M. Radzieowski et al. [J. Am. Chem. Soc. 140, 8950 (2018)], which undergoes a transition upon cooling below 45 K that was interpreted as a valence transition from Eu 2+ to Eu 3+ . In this paper, we present the discovery of another polymorph of Eu 2 ⁢Pt 6 ⁢Al 15 obtained by high temperature solution growth, which presents different physical properties than the arc-melted polycrystalline sample. Despite the similarities in crystal structure and chemical composition, the Eu valence transition is almost fully suppressed in the solution-grown crystals, allowing the moments associated with the Eu 2+ state to order antiferromagnetically at around 14 K. A detailed analysis of the crystal structure using single crystal x-ray diffraction reveals that, although the solution grown crystals are built from the same constituent layers as the arc-melted samples, these layers present a different stacking. The effect of different thermal treatments is also studied. Different anneal procedures did not result in significant changes in the intrinsic properties, and only by arc-melting and quenching the crystals we were able to convert them into the previously reported polymorph.

Schmidt, Juan [Ames Laboratory, and Iowa State Uni↗

The compressive failure of graphite/epoxy plates with circular holes

The results of an experimental investigation of the compressive behavior of T300/5203 graphite/epoxy laminated plates measuring 127.0 by 254.0 mm and containing circular holes ranging to 38.1 mm are reported. Two thicknesses, 24-ply and 48-ply, were chosen to differentiate between stability failures resulting from buckling and strength failures caused by the hole. Both quasi-isotropic and orthotropic stacking arrangements were used. The critical buckling load of the 24-ply panels was independent of hole size. Bifurcation occurred in the two half-wave mode longitudinally and one half-wave mode laterally in the quasi-isotropic panels. For the orthotropic 24-ply panels, bifurcation began in the one half-wave mode shape in each direction, but changed to the two half-wave mode before failure. Consistent post-buckling strength was exhibited by both laminated configurations. Panels with hole diameters below 3.175 mm displayed buckling before failure; those with holes larger than 6.35 mm experienced material failure around the hole before panel collapse.

Knauss, J. F.↗

Flight Test of an Intelligent Flight-Control System

The F-15 Advanced Controls Technology for Integrated Vehicles (ACTIVE) airplane (see figure) was the test bed for a flight test of an intelligent flight control system (IFCS). This IFCS utilizes a neural network to determine critical stability and control derivatives for a control law, the real-time gains of which are computed by an algorithm that solves the Riccati equation. These derivatives are also used to identify the parameters of a dynamic model of the airplane. The model is used in a model-following portion of the control law, in order to provide specific vehicle handling characteristics. The flight test of the IFCS marks the initiation of the Intelligent Flight Control System Advanced Concept Program (IFCS ACP), which is a collaboration between NASA and Boeing Phantom Works. The goals of the IFCS ACP are to (1) develop the concept of a flight-control system that uses neural-network technology to identify aircraft characteristics to provide optimal aircraft performance, (2) develop a self-training neural network to update estimates of aircraft properties in flight, and (3) demonstrate the aforementioned concepts on the F-15 ACTIVE airplane in flight. The activities of the initial IFCS ACP were divided into three Phases, each devoted to the attainment of a different objective. The objective of Phase I was to develop a pre-trained neural network to store and recall the wind-tunnel-based stability and control derivatives of the vehicle. The objective of Phase II was to develop a neural network that can learn how to adjust the stability and control derivatives to account for failures or modeling deficiencies. The objective of Phase III was to develop a flight control system that uses the neural network outputs as a basis for controlling the aircraft. The flight test of the IFCS was performed in stages. In the first stage, the Phase I version of the pre-trained neural network was flown in a passive mode. The neural network software was running using flight data inputs with the outputs provided to instrumentation only. The IFCS was not used to control the airplane. In another stage of the flight test, the Phase I pre-trained neural network was integrated into a Phase III version of the flight control system. The Phase I pretrained neural network provided realtime stability and control derivatives to a Phase III controller that was based on a stochastic optimal feedforward and feedback technique (SOFFT). This combined Phase I/III system was operated together with the research flight-control system (RFCS) of the F-15 ACTIVE during the flight test. The RFCS enables the pilot to switch quickly from the experimental- research flight mode back to the safe conventional mode. These initial IFCS ACP flight tests were completed in April 1999. The Phase I/III flight test milestone was to demonstrate, across a range of subsonic and supersonic flight conditions, that the pre-trained neural network could be used to supply real-time aerodynamic stability and control derivatives to the closed-loop optimal SOFFT flight controller. Additional objectives attained in the flight test included (1) flight qualification of a neural-network-based control system; (2) the use of a combined neural-network/closed-loop optimal flight-control system to obtain level-one handling qualities; and (3) demonstration, through variation of control gains, that different handling qualities can be achieved by setting new target parameters. In addition, data for the Phase-II (on-line-learning) neural network were collected, during the use of stacked-frequency- sweep excitation, for post-flight analysis. Initial analysis of these data showed the potential for future flight tests that will incorporate the real-time identification and on-line learning aspects of the IFCS.

Davidson, Ron↗

Layer size polydispersity in hydrated montmorillonite creates multiscale porosity networks

The aluminosilicate layers of the swelling clay mineral montmorillonite, and the saturated pores they delineate, control the mechanical properties and the transport of solutes in many natural and engineered environments. However, the structural basis of montmorillonite porosity remains poorly characterized due to the difficulty in visualizing hydrated samples in their native state. Here in this paper, we used cryogenic transmission electron microscopy (cryo-TEM) and cryo electron tomography (cryo-ET) to show that stacking defects within minimally altered, fully hydrated montmorillonite particles define multiscale porosity networks. Variations in layer lateral dimensions over tens to thousands of nanometers cause a range of topological and dynamic defects that generate pervasive curvature and introduce previously uncharacterized solute transport pathways. Observations of long-range rotational order between neighboring layers indicate that the layer-layer interactions that govern clay swelling involve three dimensional orienting forces that operate across nanoscale pores. These direct observations of the hierarchical structure of hydrated montmorillonite pore networks with nanoscale resolution reveal potentially general aspects of colloidal interactions in fluid-saturated clay minerals.

36 MATERIALS SCIENCE↗

Crystal structure, morphotropic phase transition and luminescence in the new cyclosilicates Sr{sub 3}R{sub 2}(Si{sub 3}O{sub 9}){sub 2}, R=Y, Eu-Lu

A new series of promising luminescent materials, cyclosilicates Sr{sub 3}R{sub 2}(Si{sub 3}O{sub 9}){sub 2}, R=Y, Eu-Lu, has been synthesized via a solid-state reaction. X-ray and neutron powder diffraction studies show that these oxides crystallize in the monoclinic crystal system (S.G. C2/c, Z=4) and have a morphotropic phase transition between Er and Tm compounds followed by a step-like change of the unit cell constants. Isolated [Si{sub 3}O{sub 9}] rings located in layers are basic building units and stack with Sr/R layers along the [1 0 1{sup Macron }] direction. The rare earth atoms are distributed among three independent Sr/R sites coordinated by 8, 7 and 6 oxygen atoms, and the Sr-R populations change from mixed to 0.5/0.5 over site (1) and full occupation of sites (2) and (3) by Sr and R, respectively, at the transition. Changes of the conformation and mutual arrangement of [Si{sub 3}O{sub 9}] rings, as well as exchange of oxygen atoms from the first and the second coordination sphere of two Sr/R sites also feature the phase transition. Luminescence in Sr{sub 3}Y{sub 2}(Si{sub 3}O{sub 9}){sub 2}:Eu{sup 3+} under ultraviolet (UV) excitation has been discussed. - Graphical abstract: The change of the [Si{sub 3}O{sub 9}] ring conformation in Sr{sub 3}R{sub 2}(Si{sub 3}O{sub 9}){sub 2}, R=Eu, Er, Tm and Lu. Highlights: Black-Right-Pointing-Pointer A new group of cyclosilicates Sr{sub 3}R{sub 2}(Si{sub 3}O{sub 9}){sub 2}, R=Y, Eu-Lu, was first synthesized. Black-Right-Pointing-Pointer Isolated [Si{sub 3}O{sub 9}] rings located in layers are basic building units and stack with Sr/R layers along the [1 0 1{sup Macron }] direction. Black-Right-Pointing-Pointer The rare earth atoms are distributed among three independent Sr/R sites coordinated by 6, 7 and 8 oxygen ligands. Black-Right-Pointing-Pointer A step-like change of the unit cell parameters is observed in the Sr{sub 3}R{sub 2}(Si{sub 3}O{sub 9}){sub 2} structure for R=Er{yields}Tm. Black-Right-Pointing-Pointer Sr{sub 3}Y{sub 2}(Si{sub 3}O{sub 9}){sub 2}:Eu{sup 3+} demonstrates intense multiband orange-red photoluminescence.

36 MATERIALS SCIENCE↗

Direct imaging of thermally-activated grain-boundary diffusion in Cu/Co/IrMn/Pt exchange-bias structures using atom-probe tomography

Magnetic devices are often subject to thermal processing steps, such as field cooling to set exchange bias and annealing to crystallize amorphous magnetic electrodes. These processing steps may result in interdiffusion and the subsequent deterioration of magnetic properties. In this study, we investigated thermally-activated diffusion in Cu/Co/IrMn/Pt exchange biased polycrystalline thin-film structures using atom probe tomography. Images taken after annealing at 400 °C for 60 min revealed Mn diffusion into Co grains at the Co/IrMn interface and along Pt grain boundaries for the IrMn/Pt stack, i.e., a Harrison type C regime. Annealing at 500 °C showed further Mn diffusion into Co grains. At the IrMn/Pt interface, annealing at 500 °C led to a type B behavior since Mn diffusion was detected both along Pt grain boundaries and also into Pt grains. The deterioration of the films' exchange bias properties upon annealing was correlated to the observed diffusion. In particular, the topmost Pt capping layer thickness turned out to be crucial since a faster deterioration of the exchange bias properties for thicker caps was observed. This is consistent with the idea that Pt acts as a getter for Mn, drawing Mn out of the IrMn layer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The boron-tailing myth in hydrogenated amorphous silicon solar cells

The boron-tailing effect in hydrogenated amorphous silicon (a-Si:H) solar cells describes the reduced charge collection specifically in the blue part of the spectrum for absorber layers deposited above a critical temperature. This effect limits the device performance of state-of-the art solar cells: For enhanced current density (reduced bandgap), the deposition temperature should be as high as possible, but boron tailing gets detrimental above 200 °C. To investigate this limitation and to show potential paths to overcome it, we deposited high-efficiency a-Si:H solar cells, varying the deposition temperatures of the p-type and the intrinsic absorber (i) layers between 150 and 250 °C. Using secondary ion mass spectroscopy, we study dedicated stacks of i-p-i layers deposited at different temperatures. This allows us to track boron diffusion at the p-i and i-p interfaces as they occur in the p-i-n and n-i-p configurations of a-Si:H solar cells for different deposition conditions. Finally, we prove step-by-step that the common explanation for boron tailing—boron diffusion from the p layer into the i layer leading to enhanced recombination—is not generally true and propose an alternative explanation for the experimentally observed drop in the external quantum efficiency at short wavelengths.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Demonstration of a time-integrated short line of sight neutron imaging system for inertial confinement fusion

The Neutron Imaging System (NIS) is an important diagnostic for understanding implosions of deuterium-tritium capsules at the National Ignition Facility. While the detectors for the existing system must be positioned 28 m from the source to produce sufficient imaging magnification and resolution, recent testing of a new short line of sight neutron imaging system has shown sufficient resolution to allow reconstruction of the source image with quality similar to that of the existing NIS on a 11.6 m line of sight. The new system used the existing pinhole aperture array and a stack of detectors composed of 2 mm thick high-density polyethylene converter material followed by an image plate. In these detectors, neutrons enter the converter material and interact with protons, which recoil and deposit energy within the thin active layer of the image plate through ionization losses. The described system produces time-integrated images for all neutron energies passing through the pinhole. We present details of the measurement scheme for this novel technique to produce energy-integrated neutron images as well as source reconstruction results from recent experiments at NIF.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Determination of stack plume properties from satellite imagery

LANDSAT imagery data were analyzed to determine the quantitative properties of a stack plume emitted from a moderate-sized pulp mill. Overlapping, consecutive-day MSS data provided plume/no plume radiances upwelling from the area of interest. These values from both the plume and its shadow were used to evaluate plume radius, height, particle concentration and scattering function, and total particle loading. Imagery data from a 10 by 10 km region in the vicinity of the mill were normalized to correct for minor atmospheric, solar and viewing angle changes for the two observation days, and cloud shadow data were used to evaluate sky radiance. The effects of the Sun angle, surface reflectance, SNR and spatial resolution are treated in the paper.

Staylor, W. F.↗

The Norma arm region Chandra survey catalog: X-ray populations in the spiral arms

We present a catalog of 1415 X-ray sources identified in the Norma Arm Region Chandra Survey (NARCS), which covers a 2° × 0.°8 region in the direction of the Norma spiral arm to a depth of ≈20 ks. Of these sources, 1130 are point-like sources detected with ≥3σ confidence in at least one of three energy bands (0.5-10, 0.5-2, and 2-10 keV), five have extended emission, and the remainder are detected at low significance. Since most sources have too few counts to permit individual classification, they are divided into five spectral groups defined by their quantile properties. We analyze stacked spectra of X-ray sources within each group, in conjunction with their fluxes, variability, and infrared counterparts, to identify the dominant populations in our survey. We find that ∼50% of our sources are foreground sources located within 1-2 kpc, which is consistent with expectations from previous surveys. Approximately 20% of sources are likely located in the proximity of the Scutum-Crux and near Norma arm, while 30% are more distant, in the proximity of the far Norma arm or beyond. We argue that a mixture of magnetic and nonmagnetic cataclysmic variables dominates the Scutum-Crux and near Norma arms, while intermediate polars and high-mass stars (isolated or in binaries) dominate the far Norma arm. We also present the cumulative number count distribution for sources in our survey that are detected in the hard energy band. A population of very hard sources in the vicinity of the far Norma arm and active galactic nuclei dominate the hard X-ray emission down to f{sub X} ≈ 10{sup –14} erg cm{sup –2} s{sup –1}, but the distribution curve flattens at fainter fluxes. We find good agreement between the observed distribution and predictions based on other surveys.

79 ASTRONOMY AND ASTROPHYSICS↗

Self characterization of a coded aperture array for neutron source imaging

The neutron imaging system at the National Ignition Facility (NIF) is an important diagnostic tool for measuring the two-dimensional size and shape of the neutrons produced in the burning deuterium-tritium plasma during the stagnation stage of inertial confinement fusion implosions. Since the neutron source is small (∼100 μm) and neutrons are deeply penetrating (>3 cm) in all materials, the apertures used to achieve the desired 10-μm resolution are 20-cm long, triangular tapers machined in gold foils. These gold foils are stacked to form an array of 20 apertures for pinhole imaging and three apertures for penumbral imaging. These apertures must be precisely aligned to accurately place the field of view of each aperture at the design location, or the location of the field of view for each aperture must be measured. In this paper we present a new technique that has been developed for the measurement and characterization of the precise location of each aperture in the array. We present the detailed algorithms used for this characterization and the results of reconstructed sources from inertial confinement fusion implosion experiments at NIF.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Low Cost Propulsion Technology Testing at the Stennis Space Center: Propulsion Test Article and the Horizontal Test Facility

The need for low cost access to space has initiated the development of low cost liquid rocket engine and propulsion system hardware at the Marshall Space Flight Center. This hardware will be tested at the Stennis Space Center's B-2 test stand. This stand has been reactivated for the testing of the Marshall designed Fastrac engine and the Propulsion Test Article. The RP-1 and LOX engine is a turbopump fed gas generator rocket with an ablative nozzle which has a thrust of 60,000 lbf. The Propulsion Test Article (PTA) is a test bed for low cost propulsion system hardware including a composite RP-I tank, flight feedlines and pressurization system, stacked in a booster configuration. The PTA is located near the center line of the B-2 test stand, firing vertically into the water cooled flame deflector. A new second position on the B-2 test stand has been designed and built for the horizontal testing of the Fastrac engine in direct support of the X-34 launch vehicle. The design and integration of these test facilities as well as the coordination which was required between the two Centers is described and lessons learned are provided. The construction of the horizontal test position is discussed in detail. The activation of these facilities is examined and the major test milestones are described.

Fisher, Mark F.↗

Results from the Martian Radiation Environment Experiment MARIE

One of the three science instruments aboard the 2001 Mars Odyssey spacecraft is the Martian Radiation Environment Experiment, MARIE. MARIE consists of a stack of silicon detectors, augmented by a Cerenkov detector. MARIE is designed to measure a portion of the particle spectrum of the Galactic Cosmic Rays (GCR), as well as the high fluxes of low-energy protons (energies less than about 100 MeV) that are intermittently produced by active regions on the sun in Solar Particle Events (SPE). MARIE is providing the first detailed information about the radiation environment near Mars.measurements. MARIE has been operating successfully for nearly a year. Solar particle events of considerable interest have been observed, and data have been obtained that will yield GCR spectra from a novel observation point in the solar system.

Zeitlin, C.↗

Self-Assembly Behavior of an Oligothiophene-Based Conjugated Liquid Crystal and Its Implication for Ionic Conductivity Characteristics

Here, a joint experimental and computational study on the synthesis, selfassembly and ionic conduction characteristics of a new conjugated liquid crystal quaterthiophene/poly(ethylene oxide) (PEO4) consisting of terminal tetraethyleneglycol monomethyl ether groups on both ends of a quaterthiophene core. In agreement with molecular dynamic simulations, temperature-dependent grazing-incidence wide angle X-ray scattering and X-ray diffraction indicate that the molecule spontaneously forms a smectic phase at ambient temperature as characterized both in bulk and thin film configurations. Significantly, this smectic phase is maintained upon blending with bis(trifluoro-methanesulfonyl)imide (LiTFSI) as ion source at a concentration ratio up to r = [Li + ]/[EO] = 0.05. Nanosegregation between oligothiophene and PEO moieties and π-π stacking of thiophene rings led to the formation of efficient 2D pathways for ion transport, resulting in thin film in-plane ionic conductivity as high as 5.2 x 10 -4 S/cm -1 at 70°C and r = 0.05 as measured by electrochemical impedance spectroscopy (EIS). Upon heating the samples above a transition temperature around 95 °C, a less ordered phase forms associated with a pronounced drop in ionic conductivity. Finally, upon cooling, partial and local reordering of the conducting smectic domains leads to an ionic conductivity decrease compared to the as-cast state.

36 MATERIALS SCIENCE↗

Improved modeling of photoluminescent and electroluminescent coupling in multijunction solar cells

The performance of tandem stacks of Group III-V multijunction solar cells continues to improve rapidly, both through improved performance of the individual cells in the stack and through increase in the number of stacked cells. As the radiative efficiency of these individual cells increases, radiative coupling between the stacked cells becomes an increasingly important factor not only in cell design, but also in accurate efficiency measurement and in determining performance of cells and systems under varying spectral conditions in the field. Past modeling has concentrated on electroluminescent coupling between the cells, although photoluminescent coupling is shown to be important for cells operating near their maximum power point voltage or below or when junction defect recombination is significant. Extension of earlier models is proposed to allow this non-negligible component of luminescent coupling to be included. The refined model is validated by measurement of the closely related external emission from both single and double junction cells.

14 SOLAR ENERGY↗

Moiré-Assisted Strain Transfer in Vertical van der Waals Heterostructures

Strain provides a powerful method to study 2D monolayers and to tune their properties. The same approach also has great potential for van-der-Waals (vdW) heterostructures. However, we need to understand how strain can be applied to vertically stacked vdW structures, for which strain transfer from one layer to the next remains little explored. In our experiment, we fabricated vertical heterostructures consisting of transition metal dichalcogenides (TMDCs) monolayers that were deposited on a flexible substrate. These TMDC heterostructures allowed us to read out separately the strain in each monolayer by photoluminescence measurements. We find that, in TMDC heterostructures with large twist angles (>5°), strain transfer is limited. However, for aligned heterostructures with small twist angles (≤5°), near unity strain transfer efficiency is observed. Here, we correlate this finding with the moiré domains formed in the aligned heterostructures by reconstruction.

2D materials↗