Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Data Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

Investigation of Iso-octane Ignition and Validation of a Multizone Modeling Method in an Ignition Quality Tester

An ignition quality tester was used to characterize the autoignition delay times of iso-octane. The experimental data were characterized between temperatures of 653 and 996 K, pressures of 1.0 and 1.5 MPa, and global equivalence ratios of 0.7 and 1.05. A clear negative temperature coefficient behavior was seen at both pressures in the experimental data. These data were used to characterize the effectiveness of three modeling methods: a single-zone homogeneous batch reactor, a multizone engine model, and a three-dimensional computational fluid dynamics (CFD) model. A detailed 874 species iso-octane ignition mechanism (Mehl, M.; Curran, H. J.; Pitz, W. J.; Westbrook, C. K.Chemical kinetic modeling of component mixtures relevant to gasoline. Proceedings of the European Combustion Meeting; Vienna, Austria, April 14-17, 2009) was reduced to 89 species for use in these models, and the predictions of the reduced mechanism were consistent with ignition delay times predicted by the detailed chemical mechanism across a broad range of temperatures, pressures, and equivalence ratios. The CFD model was also run without chemistry to characterize the extent of mixing of fuel and air in the chamber. The calculations predicted that the main part of the combustion chamber was fairly well-mixed at longer times (> ~30 ms), suggesting that the simpler models might be applicable in this quasi-homogeneous region. The multizone predictions, where the combustion chamber was divided into 20 zones of temperature and equivalence ratio, were quite close to the coupled CFD-kinetics results, but the calculation time was ~11 times faster than the coupled CFD-kinetics model. Although the coupled CFD-kinetics model captured the observed negative temperature coefficient behavior and pressure dependence, discrepancies remain between the predictions and the observed ignition time delays, suggesting improvements are still needed in the kinetic mechanism and/or the CFD model. This approach suggests a combined modeling approach, wherein the CFD calculations (without chemistry) can be used to examine the sensitivity of various model inputs to in-cylinder temperature and equivalence ratios. In conclusion, these values can be used as inputs to the multizone model to examine the impact on ignition delay. Additionally, the speed of the multizone model also makes it feasible to quickly test more detailed kinetic mechanisms for comparison to experimental data and sensitivity analysis.

33 ADVANCED PROPULSION SYSTEMS↗

RAPID FLUCTUATIONS IN THE LOWER SOLAR ATMOSPHERE

The Rapid Oscillations in the Solar Atmosphere instrument reveals solar atmospheric fluctuations at high frequencies. Spectra of variations of the G-band intensity (I{sub G} ) and Ca II K-line intensity (I{sub K} ) show correlated fluctuations above white noise to frequencies beyond 300 mHz and 50 mHz, respectively. The noise-corrected G-band spectrum for f = 28-326 mHz shows a power law with exponent -1.21 {+-} 0.02, consistent with the presence of turbulent motions. G-band spectral power in the 25-100 mHz ('UHF') range is concentrated at the locations of magnetic bright points in the intergranular lanes and is highly intermittent in time. The intermittence of the UHF G-band fluctuations, shown by a positive kurtosis {kappa}, also suggests turbulence. Combining values of I{sub G} , I{sub K} , UHF power, and {kappa} reveals two distinct states of the solar atmosphere. State 1, including almost all the data, is characterized by low I{sub G} , I{sub K} , and UHF power and {kappa} Almost-Equal-To 6. State 2, including only a very small fraction of the data, is characterized by high I{sub G} , I{sub K} , and UHF power and {kappa} Almost-Equal-To 3. Superposed epoch analysis shows that the UHF power peaks simultaneously with spatio-temporal I{sub G} maxima in either state. For State 1, I{sub K} shows 3.5 minute chromospheric oscillations with maxima occurring 21 s after I{sub G} maxima implying a 150-210 km effective height difference. However, for State 2 the I{sub K} and I{sub G} maxima are simultaneous; in this highly magnetized environment sites of G-band and K-line emission may be spatially close together.

79 ASTRONOMY AND ASTROPHYSICS↗

Replication Data for: Automated Detection and Characterization of Surface Restructuring Events in Bimetallic Catalysts

The data underlying this published work have been made publicly available in this repository as part of the IMASC Data Management Plan. This work was supported as part of the Integrated Mesoscale Architectures for Sustainable Catalysis (IMASC), an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Basic Energy Sciences under Award # DE-SC0012573.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The accurate assessment of small-angle X-ray scattering data

Small-angle X-ray scattering (SAXS) has grown in popularity in recent times with the advent of bright synchrotron X-ray sources, powerful computational resources and algorithms enabling the calculation of increasingly complex models. However, the lack of standardized data-quality metrics presents difficulties for the growing user community in accurately assessing the quality of experimental SAXS data. Here, a series of metrics to quantitatively describe SAXS data in an objective manner using statistical evaluations are defined. These metrics are applied to identify the effects of radiation damage, concentration dependence and interparticle interactions on SAXS data from a set of 27 previously described targets for which high-resolution structures have been determined via X-ray crystallography or nuclear magnetic resonance (NMR) spectroscopy. Studies show that these metrics are sufficient to characterize SAXS data quality on a small sample set with statistical rigor and sensitivity similar to or better than manual analysis. The development of data-quality analysis strategies such as these initial efforts is needed to enable the accurate and unbiased assessment of SAXS data quality.

36 MATERIALS SCIENCE↗

Applying mobile technology to data collection for environmental characterization and remediation, beyond the science - 15453

The rapid advancements of our time bring us new methods of analysis that enhance the accuracy and sensitivity of measurement, improving the science used to solve problems and meet our objectives. What is often overlooked in our industry are the technology advancements that can dramatically improve the speed, accuracy and completeness by which those data can be collected, communicated, managed and reported. In addition, in the time used to generate and collect the analytical data, the technology collects, manages and reports other process data that can be used to better manage and facilitate our business process improving efficiency and communications as well as providing the information needed to track and manage cost and schedule. Good information management practices, including the use of innovative technology solutions like mobile data collection, are the drivers for project implementation. However, experience has highlighted key success factors that will maximize the level of success and benefit realized by the project. These factors include: -A comprehensive, working knowledge of operational objectives; - Detailed, documented process and data work-flows; - Effective technology selection and/or development (right tool for the job); - Complete integration of the technology into day to day work practice accomplished through effective training and implementation planning. Once this formula is in place, and executed consistently, it can be applied to any environmental investigation and/or remediation scenario. The proof is in the calculated return on investment and captured lessons learned for each project. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Characterization and classification of sea ice in polarimetric SAR data

A more detailed characterization of the apparent thin ice types in the multifrequency, multipolarization synthetic aperture radar (SAR) dataset acquired during a campaign for validation of the DMSP SSM/I radiometer ice products is given. The emphasis is on providing a more detailed characterization of the signatures of apparent thin ice types observed in this data and the utility of these signatures for ice type classification purposes. The statistical characteristics of these signatures and their dependence on system calibration are summarized. Implications of these observations for sea ice scattering models are briefly discussed.

Kwok, R.↗

Fractal Characterization of Multitemporal Remote Sensing Data

Scale is an "innate" concept in geographic information systems. It is recognized as something that is intrinsic to the capture, storage, manipulation, analysis, modeling, and output of space and time data within a GIS purview, yet the relative meaning and ramifications of scaling spatial and temporal data from this perspective remain enigmatic. As GISs become more sophisticated as a product of more robust software and more powerful computer systems, there is an urgent need to examine the issue of scale, and its relationship to the whole body of spatiotemporal data, as imparted in GISs. Scale is fundamental to the characterization of geo-spatial data as represented in GISs, but we have relatively little insight on how to measure the effects of scale in representing data that are acquired in different formats and exist in varying spatial, temporal and radiometric configurations. Moreover, the complexities associated with the integration of multiscaled data sets in a multitude of formats are exacerbated by the confusion of what the term "scale" is from a multidisciplinary perspective. "Scale" takes on significantly different meanings depending upon one's disciplinary background and spatial perspective which lead to substantial confusion in the input, manipulation, analysis, and output operations. Hence, we must begin to look at the universality of scale and begin to develop the theory, methods, and techniques necessary to advance knowledge on the "Science of Scale' across all disciplines that use GISs.

Quattrochi, Dale A.↗

Fractal Characterization of Multitemporal Remote Sensing Data

Scale is an 'innate' concept in geographical information systems (GIS). It is recognized as something that is intrinsic to the capture, storage, manipulation, analysis, modelling, and output of space and time data within a GIS purview, yet the relative meaning and ramifications of scaling spatial and temporal data from this perspective remain enigmatic. As GIS becomes more sophisticated as a product of more robust software and more powerful computer systems, there is an urgent need to examine the issue of scale, and its relationship to the whole body of spatiotemporal data, as imparted in GIS. Scale is fundamental to the characterization of geo-spatial data as represented in GIS, but we have relatively little insight on how to measure the effects of scale in representing data that are acquired in different formats and exist in varying spatial, temporal and radiometric configurations. Moreover, the complexities associated with the integration of multi-scaled data sets in a multitude of formats are exacerbated by the confusion of what the term 'scale' means from a multidisciplinary perspective. 'Scale' takes on significantly different meanings depending upon one's disciplinary background and spatial perspective, which can lead to substantial confusion in the input, manipulation, analysis, and output operations. Hence, we must begin to look at the universality of scale and begin to develop the theory, methods and techniques necessary to advance knowledge on the 'Science of scale' across all disciplines that use GIS.

Quattrochi, Dale A.↗

Performance Characterization of Digital Optical Data Transfer Systems for Use in the Space Radiation Environment

Radiation effects in photonic and microelectronic components can impact the performance of high-speed digital optical data link in a variety of ways. This segment of the short course focuses on radiation effects in digital optical data links operating in the MHz to GHz regime. (Some of the information is applicable to frequencies above and below this regime) The three basic component level effects that should be considered are Total Ionizing Dose (TID), Displacement Damage Dose (DDD) and Single Event Effects (SEE). In some cases the system performance degradation can be quantified from component level tests, while in others a more holistic characterization approach must be taken. In Section 2.0 of this segment of the Short Course we will give a brief overview of the space radiation environment follow by a summary of the basic space radiation effects important for microelectronics and photonics listed above. The last part of this section will give an example of a typical mission radiation environment requirements. Section 3.0 gives an overview of intra-satellite digital optical data link systems. It contains a discussion of the digital optical data link and it's components. Also, we discuss some of the important system performance metrics that are impacted by radiation effects degradation of optical and optoelectronic component performance. Section 4.0 discusses radiation effects in optical and optoelectronic components. While each component effect will be discussed, the focus of this section is on degradation of passive optical components and SEE in photodiodes (other mechanisms are covered in segment II of this short course entitled "Photonic Devices with Complex and Multiple Failure Modes"). Section 5.0 will focus on optical data link system response to the space radiation environment. System level SEE ground testing will be discussed. Then we give a discussion of system level assessment of data link performance when operating in the space radiation environment.

Reed, Robert A.↗

A survey of solar protons and alpha differential spectra between 1 and greater than 400 MeV/nucleon

Attempts to systematically measure and fit a large sample of flare spectra from IMP 7 and 8 satellite data to determine the spectral forms that characterize the data and the range of spectral slopes are reported. Proton spectra are constructed covering the range 0.9 to over 400 MeV, and alpha fluxes from 1.4-80 MeV/nucleon. The event spectra are composed of fluxes measured at different times at each energy, and fitting procedures were employed such as a power law in kinetic energy, an exponential in rigidity, an exponential in energy, and a Bessel function of momentum/nucleon. Best fits were obtained with the exponential in rigidity and the Bessel function, with the Bessel function having a better numerical accuracy for all 21 proton spectra considered.

Mcguire, R. E.↗

Evaluation of spacecraft product assurance requirements and flight performance history

The Jet Propulsion Laboratory (JPL) has undertaken a task to relate long duration, space flight hardware performance to specific product assurance requirements established during the hardware development process. This paper describes the approach that JPL is using to correlate in-flight and ground test hardware failures to critical product assurance practices implemented on a given flight project. The first step in this effort has been to collect, and convert into a convenient format, in-flight problem, failure, and anomaly data. A characterization of a subset of this anomaly data base, focusing on anomaly causes, time dependence, and subsystem affected is presented.

Gonzalez, Charles C.↗

MeV ion-beam analysis of optical data storage films

Our objectives are threefold: (1) to accurately characterize optical data storage films by MeV ion-beam analysis (IBA) for ODSC collaborators; (2) to develop new and/or improved analysis techniques; and (3) to expand the capabilities of the IBA facility itself. Using H-1(+), He-4(+), and N-15(++) ion beams in the 1.5 MeV to 10 MeV energy range from a 5.5 MV Van de Graaff accelerator, film thickness (in atoms/sq cm), stoichiometry, impurity concentration profiles, and crystalline structure were determined by Rutherford backscattering (RBS), high-energy backscattering, channeling, nuclear reaction analysis (NRA) and proton induced X-ray emission (PIXE). Most of these techniques are discussed in detail in the ODSC Annual Report (February 17, 1987), p. 74. The PIXE technique is briefly discussed in the ODSC Annual Report (March 15, 1991), p. 23.

Leavitt, J. A.↗

Improved Characterization and Modeling of Tight Oil Formations for CO 2 Enhanced Oil Recovery Potential and Storage Capacity Estimation

Tight oil formations such as those in the Bakken petroleum system are known to hold hundreds of billions of barrels of oil in place; however, the primary recovery factor for these plays is typically less than 10%. Tight oil formations, including the Bakken Formation, therefore, may be attractive candidates for enhanced oil recovery (EOR) using CO 2 . Multiphase fluid behavior and flow in fluid-rich shales can vary substantially depending on the size of pore throats, and properties such as fluid viscosity and density are much different in nanoscale pores than in macroscale pores. Thus it is critical to understand the nature and distribution of nano-, micro-, and macroscale pores and fracture networks. To address these issues, the Energy & Environmental Research Center (EERC) has been conducting a research program entitled “Improved Characterization and Modeling of Tight Oil Formations for CO 2 Enhanced Oil Recovery Potential and Storage Capacity Estimation.” The objectives of the project are 1) the use of advanced characterization methods to better understand and quantify the petrophysical and geomechanical factors that control CO 2 and oil mobility within tight oil formation samples, 2) the determination of CO 2 permeation and oil extraction rates in tight reservoir rocks and organic-rich shales of the Bakken, and 3) the integration of the laboratory-based CO 2 permeation and oil extraction data and the characterization data into geologic models and dynamic simulations to develop predictions of CO 2 storage resource and EOR in the Bakken tight oil formation. A combination of standard and advanced petrophysical characterization techniques were applied to characterize samples of Bakken Formation tight reservoir rock and shales from multiple wells. Techniques included advanced computer tomography (CT) imaging, scanning electron microscopy (SEM) techniques, whole-core and micro x-ray CT imaging, field emission (FE) SEM, and focused ion beam (FIB) SEM. Selected samples were also analyzed for geomechanical properties. X-ray CT imaging yielded information on the occurrence of fractures, bedding planes, fossils, and bioturbation in core, as well as data on bulk density and photoelectric factor logs, which were used to interpret porosity, organic content, and mineralogy. FESEM was used for characterization of nano- and microscale features, including nanoscale pore visualization and micropore and pore throat mineralogy. FIBSEM yielded micro- to nanoscale visualization of fracture networks, porosity and pore-size distribution, connected versus isolated porosity, and distribution of organics. Results from the characterization activities provide insight on nanoscale fracture properties, pore throat mineralogy and connectivity, rock matrix characteristics, mineralogy, and organic content. Laboratory experiments demonstrated that CO 2 can permeate the tight matrix of Bakken shale and nonshale reservoir samples and mobilize oil from those samples. Geologic models were created at scales ranging from the core plug to the reservoir, and dynamic simulations were conducted. The data from the characterization and laboratory-based activities were integrated into modeling research activities to determine the fundamental mechanisms controlling fluid transport in the Bakken, which support EOR scheme design and estimation of CO 2 storage potential in tight oil formations. Simulation results suggest a CO 2 storage resource estimate range of 169 million to 1.5 billion tonnes for the Bakken in North Dakota, possibly resulting in 1.8 billion to 16 billion barrels of incremental oil.

04 OIL SHALES AND TAR SANDS↗

Generating multi-scale Li-ion battery cathode particles with radial grain architectures using stereological generative adversarial networks

Abstract Understanding structure-property relationships of Li-ion battery cathodes is crucial for optimizing rate-performance and cycle-life resilience. However, correlating the morphology of cathode particles, such as in LiNi0.8Mn0.1Co0.1O2 (NMC811), and their inner grain architecture with electrode performance is challenging, particularly, due to the significant length-scale difference between grain and particle sizes. Experimentally, it is not feasible to image such a high number of particles with full granular detail. A second challenge is that sufficiently high-resolution 3D imaging techniques remain expensive and are sparsely available at research institutions. Here, we present a stereological generative adversarial network-based model fitting approach to tackle this, that generates representative 3D information from 2D data, enabling characterization of materials in 3D using cost-effective 2D data. Once calibrated, this multi-scale model can rapidly generate virtual cathode particles that are statistically similar to experimental data, and thus is suitable for virtual characterization and materials testing through numerical simulations. A large dataset of simulated particles with inner grain architecture has been made publicly available.

25 ENERGY STORAGE↗

Using AVIRIS Data to Map and Characterize Subaerially and Subaqueously Erupted BasalticVolcanic Tephras: The Challenge of Mapping Low-Albedo Materials

Increases in the signal-to-noise ratio (SNR) in AVIRIS has enabled the mapping and characterization of low albedo materials. Low albedo materials of interest include certain soils, man-made materials (asphalt, certain building materials, tires, etc.), and basaltic lava flows and ashes. Early in its history, the response of the AVIRIS sensor was not sensitive enough so that these low albedo materials could be reliably mapped. However, as indicated by Green and Pavri (2002) the noise equivalent delta radiance (NEdL) of AVIRIS in the 2001 flight season was below 0.010 in all but the shortest wavelength channels. This is approximately a ten-fold improvement from the 1989 flight season when NEdL was closer to 0.1 (Green et al., 1990). In the current investigation, AVIRIS data from the 2002 flight season collected over the Pavant Butte tuff cone, Tabernacle Hill tuff ring, and an associated lava flow in the Black Rock Desert of west central Utah were examined to determine how well these generally low albedo volcanic lavas and tephras could be discriminated from background materials. The Pavant Butte tuff cone was examined by the author in an earlier study with a 1989 AVIRIS dataset (Farrand and Singer,

Farrand, William H.↗

Temporal Characterization and Filtering of Sensor Data to Support Anomaly Detection

Here, we present an approach for characterizing complex temporal behavior in the sensor measurements of a system in order to support detection of anomalies in that system. We first characterize typical behavior by extending a hidden Markov model-based approach to time series alignment. We then use a trace of that learned behavior to develop a particle filter that enables efficient estimation of the filtering distribution on the state space. This produces filtered residuals that can then be used in an anomaly detection framework. Our motivating example is the daily behavior of a building’s heating, ventilation, and air conditioning (HVAC) system, using sensor measurements that arrive every minute and induce a state space with 15,120 states. We provide an end-to-end demonstration of our approach showing improved performance of anomaly detection after application of alignment and filtering compared to the unaligned data. The proposed model is implemented as a computationally efficient R package alignts (align time series) built with R and Fortran 95 with OpenMP support.

47 OTHER INSTRUMENTATION↗

Power Hardware-in-the-Loop Evaluation of PV Inverter Grid Support on Hawaiian Electric Feeders

As more grid-connected photovoltaic (PV) inverters become compliant with evolving interconnections requirements, there is increased interest from utilities in understanding how to best deploy advanced grid-support functions (GSF) in the field. One efficient and cost-effective method to examine such deployment options is to leverage power hardware-in-the-loop (PHIL) testing methods, which combine the fidelity of hardware tests with the flexibility of computer simulation. This paper summarizes a study wherein two Hawaiian Electric feeder models were converted to real-time models using an OPAL-RT real-time digital testing platform, and integrated with models of GSF capable PV inverters based on characterization test data. The integrated model was subsequently used in PHIL testing to evaluate the effects of different fixed power factor and volt-watt control settings on voltage regulation of the selected feeders using physical inverters. Selected results are presented in this paper, and complete results of this study were provided as inputs for field deployment and technical interconnection requirements for grid-connected PV inverters on the Hawaiian Islands.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Itô-SDE MCMC method for Bayesian characterization of errors associated with data limitations in stochastic expansion methods for uncertainty quantification

This paper is concerned with the characterization and the propagation of errors associated with data limitations in polynomial-chaos-based stochastic methods for uncertainty quantification. Such an issue can arise in uncertainty quantification when only a limited amount of data is available. When the available information does not suffice to accurately determine the probability distributions that must be assigned to the uncertain variables, the Bayesian method for assigning these probability distributions becomes attractive because it allows the stochastic model to account explicitly for insufficiency of the available information. In previous work, such applications of the Bayesian method had already been implemented by using the Metropolis–Hastings and Gibbs Markov Chain Monte Carlo (MCMC) methods. In this paper, we present an alternative implementation, which uses an alternative MCMC method built around an Itô stochastic differential equation (SDE) that is ergodic for the Bayesian posterior. We draw together from the mathematics literature a number of formal properties of this Itô SDE that lend support to its use in the implementation of the Bayesian method, and we describe its discretization, including the choice of the free parameters, by using the implicit Euler method. We demonstrate the proposed methodology on a problem of uncertainty quantification in a complex nonlinear engineering application relevant to metal forming.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗