Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cost reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

White Earth Community Facilities Solar PV Project (Final Report)

Funded project was for the design, installation, and performance monitoring of 2 - 11.4 kW AC and 1-38.0 kW AC ground-mount solar installations for three tribal community facilities, for a total 60.8 kW AC, including a daycare facility and two community centers. Of in excess of 120 tribal buildings these facilities had showed the best promise for implementing solar, based upon site characteristics, roof loads, roof orientation and building size. The White Earth Nation seeks to move forward proactively to address the following project goals and objectives: 1) Reduction of energy costs, 2) Increasing energy security for Indian Tribes and tribal members, 3) Adding 60.8 KW in renewable energy generation (solar PV), 4) Offsets, reduces coal-fired electric energy demand by 76,397 kWh, 817,448 Source Energy Btu annually, and S) Meets the overall solar PV target set in the FOA.

14 SOLAR ENERGY↗
DOE OSTI2020

Survivability Enhancement of a Multi-Mode Point Absorber (CRADA CRD-16-631 Final Report)

The overall goal of the project is to design and validate a survival mode for the Triton wave energy converter (WEC), as shown in Figure 1, which allows for a reduction in system peak structural stresses by 50% compared to those experienced when the heave-plate is deployed in the operational configuration, while simultaneously allowing for a reduction of capital cost by 15% due to the elimination of overdesign to account for uncertainty. In addition, the project will seek to carefully understand performance of the design without survival mode engaged under extreme wave conditions so as to better understand how system loads vary and hence determine conditions where survival mode.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Predicting Deformation of Parts from HP Printers due to Sintering with Modeling and Simulation (CRADA NFE-18-07363)

This work proposes to leverage Oak Ridge National Laboratory’s (ORNL) sintering simulation software developed at the Manufacturing Demonstration Facility to 1) investigate the deformation of sintered parts and 2) to develop fast surrogate-based optimization methods for HP Inc. This includes the development of ORNL’s software on HP systems, integration and testing with HP part geometries and material properties, the development of surrogate models based on the results of the simulation, and modifications to the software based on feedback from HP. The expected impacts of this work are a drastic reduction in print costs, an increase in printer throughput, and the identification of novel, possibly exotic materials for 3D printing. This work will also decrease the time to market for HP’s print technology by decreasing the amount of resources and type dedicated to physical testing.

42 ENGINEERING↗
DOE OSTI2021

Deployment of Community Scale Solar Photovoltaic Energy Systems in Forest County Potawatomi Community

FCPC is a federally recognized tribe with a membership of more than 1400. The Tribe has a reservation in Forest County, Wisconsin, and tribal trust lands in Milwaukee County, Wisconsin, with significant governmental and business operations in both areas. Until relatively recently, FCPC was one of the poorest tribes in the Midwest. Due to its successful gaming operations, it now has improved its financial situation and is using its resources to benefit both its members and the general public through environmental and other community efforts, many of which are long-delayed because of the extended period of abject poverty. The Tribe has developed the long-term goal of becoming energy independent using renewable resources. In order to meet this goal, the Tribe has taken several important steps. As an interim step, FCPC is purchasing nearly 55 million kilowatt hours of renewable energy certificates (“RECs”) annually from certified renewable energy facilities in the United States. These RECs offset more than 100% of the present electricity use at all of the Tribe’s facilities. The Tribe is currently ranked number 11 on the Environmental Protection Agency’s (EPA) Top 20 Local Government list of green power purchasers and is a member of the EPA’s Green Power Partnership. The original project suggested small scale installations on tribal homes and certain government buildings. The Tribe suggested that the project would result in 730 kw installed. By revising the project, the Tribe was able to install 938 kw and owns the largest installation in Northern Wisconsin with the 800 kW installation at the Potawatomi Carter Casino Hotel (“PCCH”). The PCCH installation, in summer months, can provide near 90% of the use during daylight hours. Although tracking was not immediately available FCPC has since confirmed significant production with certain quarterly savings nearing $210,000. These installations provide a reduction in facility costs providing more revenue for Tribal services including cultural, health, sustainable food sources, environmental preservation and other Tribal initiatives. Further, the installations have resulted in positive steps towards the Tribe’s goals of energy sovereignty and the use of 100% renewable clean energy. Finally, the PCCH project, specifically, has had the additional benefit of providing a likely area for a microgrid. The size of the installation and offset achieved have pushed the Tribe toward planning for storage and a microgrid system that would both further the Tribe’s energy goals and provide a safe haven for the Community during times of need.

14 SOLAR ENERGY↗
DOE OSTI2021

Peridynamic Model for Single-Layer Graphene Obtained from Coarse Grained Bond Forces

An ordinary state-based peridynamic material model is proposed for single sheet graphene. The model is calibrated using coarse grained molecular dynamics simulations. The coarse graining method allows the dependence of bond force on bond length to be determined, including the horizon. The peridynamic model allows the horizon to be rescaled, providing a multiscale capability and allowing for substantial reductions in computational cost compared with molecular dynamics. The calibrated peridynamic model is compared to experimental data on the deflection and perforation of a graphene monolayer by an atomic force microscope probe.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Comprehensive Material Characterization and Simultaneous Model Calibration for Improved Computational Simulation Credibility

Computational simulation is increasingly relied upon for high-consequence engineering decisions, and a foundational element to solid mechanics simulations is a credible material model. Our ultimate vision is to interlace material characterization and model calibration in a real-time feedback loop, where the current model calibration results will drive the experiment to load regimes that add the most useful information to reduce parameter uncertainty. The current work investigated one key step to this Interlaced Characterization and Calibration (ICC) paradigm, using a finite load-path tree to incorporate history/path dependency of nonlinear material models into a network of surrogate models that replace computationally-expensive finite-element analyses. Our reference simulation was an elastoplastic material point subject to biaxial deformation with a Hill anisotropic yield criterion. Training data was generated using either a space-filling or adaptive sampling method, and surrogates were built using either Gaussian process or polynomial chaos expansion methods. Surrogate error was evaluated to be on the order of 10 ⁻5 and 10 ⁻3 percent for the space-filling and adaptive sampling training data, respectively. Direct Bayesian inference was performed with the surrogate network and with the reference material point simulator, and results agreed to within 3 significant figures for the mean parameter values, with a reduction in computational cost over 5 orders of magnitude. These results bought down risk regarding the surrogate network and facilitated a successful FY22-24 full LDRD proposal to research and develop the complete ICC paradigm.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Closing the Loop on Automotive Carbon Fiber Prepreg Manufacturing Scrap

The project demonstrated how to “close the loop” on carbon fiber by integrating industrial carbon fiber scrap into new functional components in an automotive lightweighting application. The project serves as a validation of discontinuous recycled carbon fiber in a commercial context, while generating comprehensive material data throughout the production chain. To this end, the project exhibited increasing complexity as material evaluation progressed from benchtop to commercial scale through full-scale part production, with key material properties thoroughly characterized throughout the process. Of particular focus was the form of the fiber that was fed into compounding, as recycled fiber has historically been problematic to feed at commercial-scale. Carbon fiber is energy-intensive to manufacture, so reuse of existing fiber material can reduce costs and increase sustainability. Additionally, by integrating recovered short fiber into a thermoplastic, regrind processes can be used to provide feedstock for later generations of product. While regrind plastics are not “infinitely recyclable”, reusing the manufacturing scrap over several generations of products can greatly increase material sustainability and lower the fractional embodied energy of each successive product. As such, this project supports the IACMI technical goals of (1) 25% lower carbon fiber-reinforced polymer (CFRP) cost, (2) 50% reduction in CFRP embodied energy, and (3) 80% composite recyclability into useful products. The initial stage of the project involved down selecting surface treatment (sizing) chemistries. Sizing evaluations were performed on Vartega’s chemically recycled intermediate modulus fiber along with standard modulus dry scrap which was oversized with sizing provided by Michelman. More dramatic improvements from sizing were found on the standard rather than the intermediate modulus fibers. The strength of the chemically recycled individual fibers were evaluated by Michelman and ORNL through single fiber testing and found to be comparable to similarly evaluated virgin fibers. UDRI’s mechanical testing on injection molded test specimens identified similar mechanical properties and fiber distribution relative to benchmark specimens. Additional surface chemistry tests and visualizations were performed by the Colorado School of Mines to confirm close conformance between the benchmark and recycled-fiber specimens. As the mechanical test results exceeded the 80% threshold established as the go/no-go(GNG), the project scale was increased to use commercial-scale equipment that would both better characterize the manufacturing utility of the target product format and allow qualitative assessment of a complex commercial part. An upscaled compounding evaluation was performed with a 27 mm twin-screw compounding extruding using oversized standard modulus fibers that were formatted to improve bulk solids transfer. The project team anticipated that milestone mechanical benchmarks could be achieved given the favorable performance of the sized standard modulus material identified in the initial micro-compounding trials. While the mechanical performance did meet the milestone target for that phase of the project, mechanical properties for this standard modulus-based compound were still less than those of the Ford specification. To compare the performance, the project team oversized intermediate modulus dry fibers and compounded them with the project resin at BASF using a 40 mm compounder. Test specimen mechanical performance exceeded the targets laid out in both the project milestone and the Ford specification. A series of prototype parts were successfully molded, albeit with instances of short shot components due to the high thermal conductivity of the carbon fiber compared to glass fiber for which the prototype tool was designed for. The project demonstrated that recycled carbon fiber is a viable option in fiber reinforced compound, providing greatly increased strength and modulus for applications that require them. The “agglomerated” format that facilitated effective bulk solids transfer of recovered fiber showed promise for industrial application.

36 MATERIALS SCIENCE↗
DOE OSTI2022

PACE: Producing Algae for Co-Products and Energy (Final Report)

The PACE (Producing Algae for Co-Products and Energy) consortium was comprised of scientists from national laboratories (Los Alamos National Laboratory, Pacific Northwest National Laboratory), research institutions (New Mexico Consortium), academic institutions (Arizona State University, Colorado School of Mines, Colorado State University, Washington State University) and private companies (Reliance Industries, PanPacific, Genifuel and Sonosop) dedicated to making process improvements in algal biotechnology, with an emphasis on renewable fuels and co-products from biomass. The scope of work was focused on improving algal cultivation and processing to achieve an overall energy return on investment (EROI) >3, a carbon index less than 55 grams carbon dioxide per megajoule (gCO2/MJ) and a nearly two-fold reduction in fuel cost to ≤$5 per gallon of gasoline equivalent (gge). The PACE project was originally focused on using two strains of Chlorella sorokiniana (Cs1412 and Cs1230), but later grew to encompass marine strains of Nannochloropsis and algal production strains from Reliance Industries Limited (RIL).

09 BIOMASS FUELS↗
DOE OSTI2022

Transition Metal Oxide Powders Made from Flame Spray Pyrolysis for Li-Ion Batteries

In 2012 the U.S. Department of Energy introduced its EV Everywhere Grand Challenge, with a stated goal of enabling “plug-in electric vehicles (PEVs) that are as affordable and convenient for the American family as gasoline-powered vehicles by 2022.” This requires a reduction in battery costs from the current $500/kWh to around $125/kWh. Most approaches have been to eliminate vehicle weight through lightweighting and to improve the energy density of battery materials. But what if we were able to just make the materials cheaper instead? To this end we introduce a green, low-cost method of producing cathode materials using an integrated flame spray pyrolysis process.

25 ENERGY STORAGE↗
DOE OSTI2022

Synergistic Coating-Alloy Development for Harsh Environments

The primary objective of the work was to demonstrate model alloy-coating combinations with: A. Improved oxidation resistance with a barrier coating by at least 2x vs. uncoated alloy; B. Uniform coating on a greater than 100:1 aspect ratio structure; and C. Expected reduction of lifecycle cost of a component of >25% based on customer inputs. All three objectives have been achieved.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cross-Cutting Metrology Tools for In Operando Characterization of Carrier Dynamics in Photovoltaic Devices (Final Technical Report)

Understanding the nature of recombination and its dependence on defects and interfaces is essential for engineering materials and contacts for higher V oc and photovoltaic (PV) efficiency. Time-resolved photoluminescence (TRPL) has conventionally been used to evaluate recombination, but not all materials are strongly emissive or otherwise suitable. Time-resolved terahertz spectroscopy is a pump – probe method that presents valuable complementary information, wherein an optical pump pulse photoexcites carriers within the absorber and the transient photoconductivity is probed with a terahertz pulse. Until now, experimental constraints have prohibited the use of terahertz probes to interrogate full device stacks, and measurements were instead made on exfoliated films or films grown on unconventional substrates. However, interfaces are critical to the behavior of photoexcited carriers in solar cells, and the substrates themselves often influence the film growth and bulk properties. Therefore, it is important to probe the behavior of PV absorbers as close as possible to their normal operating conditions. Here we have developed cross-cutting metrology that enable in operando characterization of carrier dynamics and recombination mechanisms in working PV devices. Through a combination of complementary non-contact TRTS and TRPL experiments and modeling, we have obtained key parameters including photoexcited carrier bulk lifetime and interface and back surface recombination velocities with greater precision and accuracy than can be achieved with conventional TRPL alone. By varying pulsed photoexcitation conditions, the contributions of interface and bulk recombination mechanisms can be determined. We have developed and refined this characterization approach by investigating CdTe PVs, which is a well-established technology but with significant margin for further improvements in efficiency. Results were published in Journal of Applied Physics (DOI: 10.1063/5.0064730) and Proceedings of the IEEE PVSC (DOI: 10.1109/PVSC43889.2021.9518559). After validating the approach, we have applied it to correlate recombination rates to processing conditions and material properties, including composition and defects as well as interfaces and surface treatments. Such feedback can inform processing and design choices to enable higher PV efficiency, not only for CdTe, but also CdSe x Te 1-x , CIGS, perovskites, kesterites, and future technologies. A perspective on predicting solar cell performance from terahertz spectroscopy was published in Advanced Energy Materials (DOI: 10.1002/aenm.202102776). The cross-cutting metrology tools developed here will enable determination of the locus and mechanism of performance-limiting recombination in thin film PV devices. This feedback can guide the engineering of PV devices with higher V oc and efficiency, thereby leading to reductions in levelized cost of electricity to meet the SunShot 2030 target of $0.03/kWh for utility-scale PV. Lower costs will enable rapid expansion of renewable electricity generation that is nearly free of carbon emissions. Reducing carbon emissions of the electricity sector is one of the most important solutions to climate change. The project’s specific focus on CdTe PV can benefit First Solar, the US company that is the global leader in CdTe technology, through both technology and workforce development.

14 SOLAR ENERGY↗
DOE OSTI2022

High Strength Steel-Aluminum Components by Vaporizing Foil Actuator Welding

This project aimed to address the challenge of effectively welding dissimilar materials—high-strength steel and high-strength aluminum for creating lightweight, multi-material automotive components. For automotive companies, reducing weight of a vehicle is critical task regulated by the government to solve the issue of greenhouse gas emissions. Production of lightweight cars and trucks can be achieved by substitution of current all-steel structures with multi-material lightweight structures that include high strength-to-weight-ration materials such as high-strength steels, aluminum alloys, magnesium alloys, titanium alloys, coupled with lightweight designs. This requires dissimilar metal welding, which is challenging for state of the art joining processes such as resistance spot welding. The cycle of melting-cooling-freezing during traditional welding that can easily ruin the designed outstanding properties of the advanced base metals, such as aluminum alloys, making the welded area much weaker than the base metals. To weld two different metals with great difference in melting points, such as aluminum and steel, it’s even more difficult or impossible because of the formation of brittle intermetallic compounds at the welded interface. In this project, a novel welding method, developed at OSU, was selected for validation and development. This novel technology enables welding by impact without melting and proves to be robust to join various dissimilar lightweight metals. Termed as vaporizing foil actuator welding or VFAW, the technology uses a thin aluminum foil that is rapidly vaporized by a high current pulse to produce an explosive-like pressure pulse to drive one metallic piece into another at the high speed required for impact welding. This project entailed development of the early-stage welding technology in terms of (a) the consumables, the welding apparatus and the power sources, (b) coupon scale screening of many material combinations including corrosion studies, (c) computational modeling and design of the welded interface as well as of the multi-material prototype component, and (d) mechanical testing for strength and durability at coupon scale and to a certain extent the prototype scale. The all-steel engine cradle of 2016 Chevrolet Cruze was chosen as the baseline prototype component. The target set for the project was to demonstrate a 20% weight reduction at a cost premium of less than $\$ $5/lb saved without compromising on baseline mechanical properties. At project completion, a 12% lighter prototype component was demonstrated with an estimated cost premium of $\$ $9.8/lb saved. Besides prototype level demonstration of the technology, this project also enabled elevation of the technology’s readiness level to where a hydraulically actuated welding head was developed and made ready for deployment at a research and development facility for Tier 1 automotive supplier.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Technology Maturation of Wireless Harsh Environment Sensors For Improved Condition Based Monitoring Of Coal Fired Power Generation

The overall goal of this project was to demonstrate and develop the usage of high-temperature (HT) harsh-environment (HE) wireless surface acoustic wave resonator (SAWR) sensor technology to promote reliable maintenance through condition-based maintenance (CBM) for field applications in harsh service conditions associated with power plant environments. The project aimed to advance the HT HE wireless SAWR sensor technology from TRL 5 to TRL 7. In addition to HT HE wireless temperature sensing, efforts were dedicated during this project to investigate, develop and increase the TRL from 3 to 5 for the following technologies: (a) HT HE strain sensors to address additional CBM monitoring needs, such as boiler tube mechanical / thermal stresses, which can provide early indications for boiler tube cracking and failure; and (b) HT aluminum nitride (AlN) and scandium aluminum nitride (ScAlN) based piezoelectric thin film fabrication and implementation of SAW sensors, with the goal of releasing the need to use single crystal piezoelectric materials for SAWRs and thus broaden possible technology applications to non-planar and harder to modify surfaces. To achieve the goals mentioned above, UMaine and its partner, Environetix Technologies Corporation, established partnerships with the following power plants: Longview Power (Maidsville, WV), a coal-fired power plant; Penobscot Energy Recovery Corp (PERC, Orrington, ME), a waste-to-energy power plant; and the UMaine Steam Plant (Orono, ME), an oil / natural gas power plant. To realize wireless HT HE SAWR sensor systems in these harsh service conditions, the University of Maine research team worked with Environetix and these power plants to define, design, fabricate, test and validate a mature prototype wireless temperature SAWR sensor system for boiler tube applications within the HT HE of the reheater pass damper chamber to directly and wirelessly monitor the temperature at eighteen independent boiler tube locations. The system included three levels, or “tiers”, of wireless communication to enable remote monitoring: Tier 1, the wireless link in the reheater pass damper chamber directly accessing the sensors on the boilers; Tier 2, the wireless local area network link, transmitting processed sensor information within the power plant to the Tier 3, a commercial wireless signal carrier company for secure remote data monitoring outside of the power plant. Regarding the wireless sensor system installed at Longview Power, temperature information from the boilers was continuously transmitted from the Longview boilers at Maidsville, WV, to Environetix headquarters, Orono, ME, over a 34 month period, when the system was finally decommissioned. Strain sensors and piezoelectric ScAlN thin film sensors were successfully installed on the exhaust duct at the UMaine Steam Power plant. The advances in wireless strain sensors and thin film piezoelectric film fabrication and testing were performed mostly in UMaine laboratories and field tested at the UMaine Steam Plant, due to its close proximity to UMaine/Environetix, access to the plant facility, and due to difficulties in accessing the other power plants during the COVID shut-down period. The project accomplished the TRL level increase of the targeted CBM technologies through the successful fabrication, installation, test, and validation of dedicated and commercial wireless sensor systems, utilizing the three different power plants. The outcomes of this project, including the wireless sensor data capability, are expected to yield an advance for CBM in harsh power plant environments. The reduction of maintenance costs, improved safety during plant operation, and increased power plant efficiency will lead to increased revenues (i.e., fewer forced outages) due to better process monitoring enabled by the wireless HT HE SAWR temperature sensor technology.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2023

Development of a Novel Magnesium Alloy for Thixomolding® of Automotive Components (Final Report)

Magnesium (Mg) alloy die-castings are increasingly used in the automobile industry to achieve cost effective mass reduction, especially in systems where multiple components can be integrated into a single thin wall die-casting. However, there are several component quality restrictions in thin-walled Mg die castings, including variability in dimensional accuracy, part-to-part variation in mechanical properties, and porosity in the final part, which has limited the continued growth of die-cast components in the automobile industry. An alternative to die-casting is the process of thixomolding®. While the die-casting process relies on filling a mold at high speeds with the alloy in the completely molten state, the thixomolding® process fills a mold with a thixotropic alloy in a semi-solid slurry state at a temperature between the liquidus and solidus temperatures. Ideally, the material should be ~30–65% solid rather than being completely liquid at the beginning of the injection process. Advantages of the thixomolding® process include a finer grain structure, lower porosity, improved dimensional accuracy, improved part-to part consistency, improved mechanical properties, particularly ductility in the component, the ability to reduce wall thickness for mass savings, and longer tool life due to lower process temperatures. The objective of this collaborative project between Oak Ridge National Laboratory, FCA US LLC, and Leggera Technologies was to develop one or more novel Mg alloys more suitable for thixomolding® automotive structural components than the current die-casting alloys used for this process. The primary interest was to improve ductility while maintaining tensile and fatigue strengths, as these are properties that are critical for use in body and chassis structural applications. Since good corrosion resistance is also desirable for this application, this property was also considered when evaluating promising alloy compositions. An initial evaluation of existing components thixomolded® using AM60 was performed and microstructure, and tensile properties were evaluated for the baseline alloy. Targets were established for ease of processing (characterized by the melting range defined as the difference between the liquidus and the solidus), strength, and ductility. Computational modeling was used to identify promising alloys and selected alloys were cast in laboratory scale heats. Properties measured from laboratory scale heats were used to down-select two alloys for further evaluation and component fabrication. Two alloys were prepared in industrial scale heats, cut into small pieces (chips), and thixomolding® trials were initiated. Trial components were successfully fabricated using one alloy composition, but it was concluded that further refinement of the thixomolding® process parameters are required to successfully fabricate component using second alloy. Microstructure and mechanical properties were evaluated on the material removed from the fabricated component and properties were compared to the baseline alloy. Although mechanical properties of the alloys showed improvement over the baseline alloy, it was determined that modifications to the thixomolding® process would result in better microstructure control with further improvement in properties leading to successful commercialization. A provisional patent application has already been filed on the new alloys developed as part of the project.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Annual report for DOE VTO

Carbon fiber (CF)/polymer composites are a transformative class of high-performance, lightweight material, where high aspect-ratio CFs reinforce a polymer matrix and exceed the strength of steel alloys at a fraction of the density. Despite the advantages of such a class of material, the broader implementation of CF composites in a range of automotive, aerospace, and energy applications is hindered by limitations of current manufacturing methods. These current techniques (e.g., hand lay-up, wet filament winding) are costly and impose severe limitations on fiber placement, orientation, and angle, and thus a composite’s ultimate properties. Today’s CF composites are expensive to manufacture, limited in form factor, and utilize costly and sub-optimal continuous filament CF. Advanced additive manufacturing (AM) processes, combined with computational design optimization and new approaches to resin development, offer alternative design and manufacturing paradigms that have the realistic potential to lift these constraints. Such integrated AM approaches could thus help to realize the full potential of CF composite materials. One relevant application of CF composite materials where manufacturing constraints limit the cost-benefit ratio is in the manufacture of high-performance composite pressure vessels for onboard compressed natural gas (CNG) storage. Current CNG storage vessels (Types 3–5) are made from load-bearing filament-wound carbon-fiber composite and are ~3.5 times as expensive as an all-metallic Type-1 vessel. This cost is invariably tied to the complex and labor-intensive nature of conventional filament winding processes and the large volumes of expensive high tensile-strength CF tow feedstock required in manufacture. Our proposed approach to CNG storage vessel manufacture is based on a combination of AM technologies for CF composite printing and design optimization tools that were pioneered at Lawrence Livermore National Laboratory (LLNL), with advances in resin/composite formulation enabled by chemical and nano-material modification. Through the successful development of this technology, LLNL seeks to demonstrate the capability for advanced CNG storage vessel manufacture at reduced cost with no reduction in performance versus the most advanced, extant Type-5 designs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Accelerated Scaling to Rapid Open-Air Fabrication of Durable Perovskite Solar Modules

The goals of this SETO project (DE-EE0008559, Accelerated Scaling to Rapid Open-Air Fabrication of Durable Perovskite Solar modules) are to address the principal challenges towards the successful commercialization of perovskite solar modules utilizing scalable, high-throughput open-air spray deposition. The successful outcome of the project will provide the foundation of an all open-air spray deposited perovskite solar module with hole transport layer (HTL), perovskite, electron transport layer (ETL), and barrier layer development while establishing a fundamental understanding of perovskite device behavior under accelerated aging conditions. Through this program, we have made significant progress towards a commercializable pathway for perovskites. (1) We’ve demonstrated the successful open-air deposition of perovskite and transport layer materials. These deposition methods were chosen for their inherent scalability, and open-air processing enables a significant reduction in processing costs. These methods are also compatible with high throughputs, demonstrating the fastest perovskite film deposition at these performance levels. (2) Development of a unique all-fiber laser scribing procedure provides a high-performance, low-cost method for further improvements in scalability. (3) Our group has also placed a unique emphasis on device stability. The development of testing standards for perovskite modules is required to thoroughly evaluate potential candidates for commercialization, and we’ve taken inspiration from current industry standards to provide an honest insight into the performance and reliability of our devices. (4) An extensive cost model detailing the specific contributions of each device layer and production component provides the most thorough evaluation of any perovskite technology against conventional silicon and compound semiconductor solar devices. The cost model is a critical advancement that will provide the foundation for evaluating the levelized cost of energy (LCOE) of this technology.

14 SOLAR ENERGY↗
DOE OSTI2023

Modeling of High Solids Biomass Liquefaction, Techno-economic Assessment and Life Cycle Assessment for Industrial Scale UP

Biomass liquefaction improves corn-stover slurry transport within a biorefinery, and reduces challenges associated with solids handling. Slurries, formed with yield stresses (i.e., viscosities) that are low enough to facilitate pumping from one unit operation to the next, and that enable mixing at reasonable power inputs in large fermentation vessels, enable scaling of cellulose fermentations. Three liquefaction methods: enzyme, enzyme mimetic, and a hybrid approach were analyzed by a combination of techno-economic and life-cycle analyses, resulting in an assessment of cost-effectiveness and environmental impact. Of the three scenarios, enzyme-based processes emerged as the most efficient, both in cost and emissions reduction (gCO2-equivalent/kg slurry).

Ramirez, Jorge↗
DOE OSTI2024

Natural Gas Combined Cycle Power Plants with Carbon Capture and Exhaust Gas Recycle

This is a presentation given at the 3rd International Conference on Energy and Environment. The presentation highlights analysis work conducted by NETL to assess the cost and performance for natural gas combined cycle (NGCC) power plants that incorporate solvent-based post combustion carbon dioxide (CO2) capture and exhaust gas recycle (EGR). Increasing the inlet CO2 concentration by EGR is expected to improve the efficiency of the capture system and reduce its cost, however the analysis results show that the cost improvement is minimal as is the cost of capture reduction.

Hackett, Gregory↗