Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Combustion modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Testing- and Model- Based Optimization of Coal-fired Primary Heater Design for Indirect Supercritical CO 2 Power Cycles (Final Scientific and Technical Report)

The overall objective of this project was to perform the R&D necessary to mitigate the risk associated with the design of a primary heat exchanger for a solid-fired combustion system coupled with an indirect-fired closed-loop Brayton Cycle utilizing supercritical CO 2 . The key technological hurdle was the coupling of a solid-fuel firing system with the primary heater, which poses a singular challenge, which is the management of burner performance and operational conditions in a way to manage heat exchanger tube metal temperatures and temperature ramp rates in the absence of fluid phase change on the inside of the tubes. We designed and built the first ever pseudo power system employing a simple recuperated supercritical CO 2 closed-loop Brayton Cycle coupled to a solid-fuel fired system. Advanced coupled CFD and process modeling were used to design the primary heat exchanger (PHX), which consisted of both radiative and convective sections, to limit tube metal temperatures resulting from the heat release profile of the solid fuel flame near the radiative tubes. The heat exchanger was designed to produce finished CO 2 temperatures of 600 °C a pressure of 20.7 MPa and CO 2 flow of 5.5 kg/s. The constructed PHX was capable of 1.2 MWth heat uptake. During design of the PHX, the modeling showed that most variables influencing flame shape (burner stoichiometric ratio and register velocities and swirl) were not suitable to manage heat flux to the metal surfaces. This is because they substantially increased adiabatic flame temperature through the influence of localized stoichiometric ratio. Excess air and firing rate were the two most powerful variables that could be used to control tube surface temperatures. The coupled system was operated for a total of 407 hours, with the longest continuous run of 248 hours. For 62% of the operational time, the unit was unmanned and in automatic control. The fuels used for the testing included natural gas, two Utah Bituminous coals, woody biomass, and bagasse. During the testing we were able to verify the 1.2 MWth heat uptake and we operated at a finished CO 2 temperature of 607 °C and a pressure of 20.3 MPa simultaneously. The real-time corrosion rate of the Super 304H tube CO 2 surface in the region of the radiative section of the PHX were measured, at an approximate temperature of 550 °C. The two key variables related to corrosion rate are the pressure and flow rate of the CO 2 . A technoeconomic analysis was performed at a scale of 120 MWE. The updated analysis showed that the efficiency of an sCO 2 power producing plant will be related to the pressure drop of the PHX.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

FLEX-FUEL MIXING CONTROLLED COMBUSTION ENABLED BY PRECHAMBER IGNITION

There is an imminent need to displace fossil diesel fuel with cleaner burning, domestically produced, renewable fuels for use in heavy-duty engines. Bioethanol is a prime candidate as it widely adopted in the U.S. as a gasoline additive ranging in volume percentage from 10% (E10) up to 85% (E85). Direct substitution of market available ethanol-gasoline blends for diesel fuel is not plausible as the stark reactivity differences would not constitute the same ignition quality nor achieve auto-ignition at all. This work focuses on the development of prechamber enabled mixing-controlled combustion (PC-MCC) as an advanced combustion strategy to facilitate reliable ignition and diffusion style combustion ethanol-gasoline fuel blends. PC-MCC involves integration of an actively fueled prechamber (PC) into a conventional compression ignition combustion system. When ignited, the PC ejects hot turbulent jets into the main combustion chamber that then interact with the direct injected fuel, prompting immediate ignition. The PC jet flames provide a robust thermal ignition source that allows the engine to operate agnostic of fuel composition, or flex-fuel. Computational fluid dynamics (CFD) modeling was used to assess critical design features of the PC while garnering insights into the ignition strategies that facilitate robust performance. A key finding was the ignition performance benefits of fuel-rich PC operation which yield exothermic jets. Based on the numerical findings, a prototype igniter was tested experimentally on both single and multi-cylinder engine platforms at a variety of operating conditions. The experimental results indicate flex-fuel PC-MCC is well capable of diesel-like combustion processes by demonstrating matched or improved gross thermal efficiencies and load variability within 2%. Fuel grade ethanol (E98) exhibited consistently lower NOx and immeasurable soot across the load space. E98 also demonstrated a significant improvement in thermal efficiency at light loads.

Zeman, Jared↗
DOE OSTI2021

Effects of non-thermal termolecular chemistry on detonation development in hydrogen (H2) / methane (CH4) - air mixtures

In combustion simulations, it is usually assumed that highly-energized collision complexes (either radical or stable species) formed in exothermic reactions are always under thermal equilibrium as they evolve through competing networks of reactions. However, in practical flames, non-trivial amounts of reactive radicals such as H, O and OH are present apart from O2. As a result, collisions of these reactive species with the energized collision complexes have been shown in recent studies to induce non-thermal reactivity. These studies have also demonstrated that such non-thermal reactions can be suitably represented in macroscopic kinetics models as chemically termolecular reactions. The present work was focused on identifying and quantifying the effects of including such reactions on the evolution of an initial deflagration front to a developing detonation in H2/CH4-air mixtures under boosted internal combustion (IC) engine conditions. Specifically, fully resolved simulations, with and without non-thermal reactivity, were performed for a constant volume reactor containing stoichiometric H2/CH4-air mixture. It was found that inclusion of termolecular chemistry resulted in a delayed onset of end-gas auto-ignition. Concurrently, the developing detonation intensity was observed to be significantly higher. Chemical explosive mode analysis (CEMA) was performed to identify the dominant species/reactions responsible for the observed variation in the results.

Detonation↗
DOE OSTI2024

Exploring Grid-Interactive Efficient Building Strategies for Laboratories Through Energy Modeling

Laboratories are often overlooked in demand flexibility research due to constraints on their operations as mission critical facilities, despite the major role they play in an organization's emissions. Laboratories consume 3-4 times more energy than a typical office building and are commonly the largest energy users on any campus. Consequently, most laboratories in the United States are significant contributors to their organization's carbon footprint if their energy needs are met through the combustion of fossil fuels. As part of the initiative to decarbonize laboratories, this report documents an analysis on specifically grid-interactive efficient building (GEB) opportunities for reducing energy costs and emissions associated with laboratory operations. The goal of this initiative was to provide a case study and guidance on how to use OpenStudio and REopt as modeling tools for GEB technologies and strategies in laboratory environments across different climate zones in the United States. The analysis found that efficiency-based GEB strategies had the most significant impact on laboratory operations, while load-shedding and load-shifting GEB strategies produced smaller results. The culmination of these approaches applied across all five climate zones generated on average: 1) 28% energy cost savings and 30% greenhouse gas (GHG) emissions reductions, and 2) 4% enhanced energy cost savings under a time-of-use (TOU) pricing schedule compared to traditional pricing schemes. Grid-interactive efficiency building measures were found to produce the greatest energy savings in both electricity and natural gas, particularly in regions with high electrical loads, such as warm climates for cooling. Laboratories that had high levels of natural gas consumption, meanwhile, experienced the greatest emission reductions. The report concludes with an analysis on the opportunities for flexible loads in lab spaces and how small-scale measures in addition to opaque pricing structures for peak demand could become barriers to demand flexibility planning. The report also explores how electrifying laboratory buildings with heat pumps could reduce energy costs and GHG emissions.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Laminar Burning Speed Measurements of Hydrogen/Natural Gas Mixtures

Abstract To address the shortage of fossil fuels and the environmental impact of exhaust emissions, research efforts in combustion seek to identify candidates for sustainable fuels. Hydrogen is an example, from which water is produced as the main combustion product. However, when used as neat hydrogen, it is very difficult to control hydrogen combustion due to its high flame speed, pre-ignition propensity, and flashback characteristics. One method to control hydrogen combustion is to blend it with a well-established fuel. Natural gas is a common fuel for use in engines or gas turbines. Natural gas is characterized by slow flame speeds and poor lean-burn ability; thus, engine power is decreased in the lean-burn region. Consequently, natural gas engines are typically operated at stoichiometric conditions to maximize output. Blending hydrogen to natural gas has several advantages: (i) Control of hydrogen’s ignition characteristics, (ii) extension of Natural gas’s lower flammability limit — making it easier to ignite, and (iii) reduced greenhouse gas emissions. In this study, the laminar burning speed (LBS) for neat natural gas and natural gas/hydrogen mixtures at 5 atm and 296 K were measured. Schlieren optical imaging was utilized to validate laminar flame conditions and further investigate the structure of natural gas/hydrogen flames. Results indicate that replacing 50% of natural gas with hydrogen increases the peak laminar burning velocity by a factor of ∼1.6 times. LBS simulations were conducted with NUI 1.1 and UCF NG/H2 mechanisms; Predictions by both mechanisms were found to be satisfactory for neat NG mixtures. However, for 50% NG/ 50% H2 mixture, the true LBS for fuel-lean conditions was under-predicted by both models, while predictions for fuel-rich conditions were satisfactory. Additionally, a literature review and similar experimental analysis will be performed for methane, ammonia, and hydrogen fuel blends to better understand the combustion phenomena of natural gas fuels.

Yovino, Louis↗
DOE OSTI2020

Thermodynamics and kinetics of solution combustion synthesis: Ni(NO 3 ) 2 + fuels systems

Solution combustion synthesis (SCS) utilizes exothermic self-propagating reactions to prepare nanoscale materials that can be used widely in energy, electronics, and biomedical technologies and other applications. SCS is a specific variety of a more general combustion synthesis (CS) method. Investigations of the thermodynamics, kinetics, and the mechanisms of SCS reactions, are not as well studied as the other CS processes. This work reports on a systematic study of the thermodynamics and kinetics of SCS reactions involving Ni(NO 3 ) 2 , an oxidizer, and either glycine (C 2 H 5 NO 2 ) or hexamethylenetetramine (HMT, C 6 H 12 N 4 ) as fuels. A thermodynamic modeling approach, based on the Gibbs free energy minimization principle, is applied to the simultaneous calculations of the adiabatic temperatures and compositions of the equilibrium products. Our calculations reveal the influence of fuel-to-oxidizer ratio, amount of water, and the oxygen in air on the combustion temperature under adiabatic conditions and the composition of the resulting products. We have, in turn, measured the combustion temperature and phase composition of products and compared them with the calculations. Variations of drying times for the solutions yield precursor gels with varying water contents. This approach enables the manipulation of combustion parameters and confirms the use of calculated activation energies for reactions using the Merzhanov-Khaikin method. Here, the results show that SCS reactions in fuel-lean solutions producing NiO have higher activation energy in contrast to reactions with fuel-rich solutions that form Ni. Reduction of activation energies due to the increase in the fuel-to-oxidizer ratio could be related to the observed change of the rate-limiting stages of the endothermic decomposition of the individual reactants to the exothermic decomposition of coordinate compounds formed between the reactants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Fuel molecular structure effect on autoignition of highly branched iso-alkanes at low-to-intermediate temperatures: Iso-octane versus iso-dodecane

Highly branched iso-alkanes are an important class of hydrocarbons found in conventional petroleum-derived and alternative renewable fuels used for combustion applications. Recognizing that chemical kinetics for most of these iso-alkanes, especially at low-to-intermediate temperatures, has not been well studied, an experimental and modeling investigation of two selected iso-alkanes, iso-octane (2,2,4-trimethylpentane, iC8) and iso-dodecane (2,2,4,6,6-pentamethylheptane, iC12), is conducted to understand the fuel molecular structure effect on their autoignition characteristics. Using a rapid compression machine (RCM), the ignition responses of iC8 and iC12 at varying pressures, temperatures, and equivalence ratios are characterized and compared. The newly-acquired experimental ignition delay times have been compared with the literature RCM and shock tube data, demonstrating the complementary nature of the current dataset. Further comparison of the experimental pressure traces and ignition delay times illustrates the reactivity crossover between iC8 and iC12. Namely, there exists a temperature window in the negative temperature coefficient regime within which iC12 is less reactive than iC8, but iC12 becomes more reactive outside this temperature window. Furthermore, a chemical kinetic model of iso-alkanes including both iC8 and iC12 is developed. Simulated results using this model are then compared to the experimental data obtained in this study and available in the literature, showing its ability to predict the experimental trends. Chemical kinetic analyses have also been conducted to identify the important reaction pathways controlling autoignition at varying conditions, and to elucidate the underlying mechanism leading to different reactivity trends between iC8 and iC12.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Pixel-Resolved Long-Context Learning for Turbulence at Exascale: Resolving Small-scale Eddies Toward the Viscous Limit

Turbulence plays a crucial role in multiphysics applications, including aerodynamics, fusion, and combustion. Accurately capturing turbulence's multiscale characteristics is essential for reliable predictions of multiphysics interactions, but remains a grand challenge even for exascale supercomputers and advanced deep learning models. The extreme-resolution data required to represent turbulence, ranging from billions to trillions of grid points, pose prohibitive computational costs for models based on architectures like vision transformers. To address this challenge, we introduce a multiscale hierarchical Turbulence Transformer that reduces sequence length from billions to a few millions and a novel RingX sequence parallelism approach that enables scalable long-context learning. We perform scaling and science runs on the Frontier supercomputer. Our approach demonstrates excellent performance up to 1.1 EFLOPS on 32,768 AMD GPUs, with a scaling efficiency of 94\%. To our knowledge, this is the first AI model for turbulence that can capture small-scale eddies down to the dissipative range in three-dimensional turbulence at high Reynolds numbers.

Yin, Junqi [ORNL] (ORCID:0000000338435520)↗
DOE OSTI2020

Computationally efficient evaluation of optimum homogeneous charge compression ignition operating range with accelerated multizone engine cycle simulation

The very intensive calculations necessary to define a performance map requiring evaluation of over a hundred individual operating points can be efficiently conducted with accelerated multizone for engine cycle simulation, leading to a definition of regions of acceptable and optimum homogeneous charge compression ignition operation. Accelerated multizone for engine cycle simulation has the virtue of enabling accurate evaluation of many operating conditions based on thermal stratification data from a single fluid mechanics run at motored conditions. This is possible because thermal stratification is more sensitive to engine geometry than to operating conditions. In this article, accuracy of accelerated multizone for engine cycle simulation is demonstrated by comparison with experimental data for iso-octane homogeneous charge compression ignition operation over a broad range of lean equivalence ratios (0.14–0.28). The validated accelerated multizone for engine cycle simulation model is then applied to generating a performance map for an engine controlled by appropriately adjusting equivalence ratio and internal exhaust gas recirculation. Regions of acceptable and optimum combustion are identified. It is finally demonstrated that while indicated mean effective pressure remains low for optimum homogeneous charge compression ignition operation (1–4 bar), this is sufficient for a large fraction of typical driving in light-duty vehicles. Much driving including idle can therefore be done in homogeneous charge compression ignition mode at high efficiency and low (essentially zero) NOx and particulate matter emissions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Sensor System and Observer Algorithm Co-Design For Modern Internal Combustion Engine Air Management Based on H2 Optimization

This paper outlines a novel sensor selection and observer design algorithm for linear time-invariant systems with both process and measurement noise based on H 2 optimization to optimize the tradeoff between the observer error and the number of required sensors. The optimization problem is relaxed to a sequence of convex optimization problems that minimize the cost function consisting of the H 2 norm of the observer error and the weighted l 1 norm of the observer gain. An LMI formulation allows for efficient solution via semi-definite programing. The approach is applied here, for the first time, to a turbo-charged spark-ignited engine using exhaust gas circulation to determine the optimal sensor sets for real-time intake manifold burnt gas mass fraction estimation. Simulation with the candidate estimator embedded in a high fidelity engine GT-Power model demonstrates that the optimal sensor sets selected using this algorithm have the best H 2 estimation performance. Sensor redundancy is also analyzed based on the algorithm results. This algorithm is applicable for any type of modern internal combustion engines to reduce system design time and experimental efforts typically required for selecting optimal sensor sets.

Zhang, Xu↗
DOE OSTI2022

Numerical and Experimental Investigations on the Ignition Behavior of OME

On the path towards climate-neutral future mobility, the usage of synthetic fuels derived from renewable power sources, so-called e-fuels, will be necessary. Oxygenated e-fuels, which contain oxygen in their chemical structure, not only have the potential to realize a climate-neutral powertrain, but also to burn more cleanly in terms of soot formation. Polyoxymethylene dimethyl ethers (PODE or OMEs) are a frequently discussed representative of such combustibles. However, to operate compression ignition engines with these fuels achieving maximum efficiency and minimum emissions, the physical-chemical behavior of OMEs needs to be understood and quantified. Especially the detailed characterization of physical and chemical properties of the spray is of utmost importance for the optimization of the injection and the mixture formation process. The presented work aimed to develop a comprehensive CFD model to specify the differences between OMEs and dodecane, which served as a reference diesel-like fuel, with regards to spray atomization, mixing and auto-ignition for single- and multi-injection patterns. The simulation results were validated against experimental data from a high-temperature and high-pressure combustion vessel. The sprays’ liquid and vapor phase penetration were measured with Mie-scattering and schlieren-imaging as well as diffuse back illumination and Rayleigh-scattering for both fuels. To characterize the ignition process and the flame propagation, measurements of the OH* chemiluminescence of the flame were carried out. Significant differences in the ignition behavior between OMEs and dodecane could be identified in both experiments and CFD simulations. Liquid penetration as well as flame lift-off length are shown to be consistently longer for OMEs. Zones of high reaction activity differ substantially for the two fuels: Along the spray center axis for OMEs and at the shear boundary layers of fuel and ambient air for dodecane. Additionally, the transient behavior of high temperature reactions for OME is predicted to be much faster.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Informed Critical Mineral Recovery from Fossil Energy Waste Feedstocks

Critical minerals (CM), such as rare earth elements (REE), cobalt, nickel, and lithium, have important uses in modern energy and technologies, yet are vulnerable to potential supply chain disruptions. One potential domestic CM source is fossil energy wastes, such as coal combustion ash, acid mine drainage (AMD) and treatment solids (AMD solids), and Oil and Gas (O&G) drilling wastes (drill cuttings and produced waters). CM recovery from these feedstocks is promising due to their abundant quantity and fast availability as waste products. To develop informed and effective CM recovery, DOE’s National Energy Technology Laboratory (NETL) have collected and analyzed CM data for aforementioned fossil energy wastes, and utilized advanced geochemical characterization (e.g., synchrotron microprobe, sequential extraction and geochemical modeling) to identify the CM speciation and binding environments. Novel methods that recover multiple CMs while co-producing other valuable byproducts from these feedstocks have been developed. Successful examples include: (1) the discovery of easily mobile REE phases in Ca-rich coal combustion ash resulted in a patented REE recovery process from the ash feedstock while producing zeolite sorbents from the extraction wastes; (2) the successful identification of REE/Co/Ni/Zn hosting phases in acid mine drainage treatment solids (AMD solids) has informed the sequential CM recovery from AMD solids and has inspired lithium sorbent development from the extraction wastes; (3) the recovery potential of Li and other CMs in O&G produced waters and drill cuttings has been explored while the extraction residuals have been demonstrated to support plant growth as soil supplements. The innovations driven by characterization information have the potential to maximize CM recovery revenue, offset the cost of waste management and wastewater treatments while reducing the cost and environmental footprint of CM extraction.

characterization and extraction of rare earth elem↗
DOE OSTI2023

Design and Modeling of a Demonstration-scale ORC Cycle for the Liquid Air Combined Cycle

Energy storage is becoming an increasing focus for the future energy markets. One potential hybrid system for ling duration energy storage is the Liquid Air Combined Cycle (LACC). The LACC utilizes excess renewable energy to liquefy and store air during the charge cycle. During its discharge cycle, the system uses the exhaust heat from a conventional combustion turbine and an ORC bottoming cycle to vaporize and superheat the stored air that has been pressurized, which is subsequently expanded to atmosphere through a turbine. During the development of the cycle, it has been identified that the main technologies to advance the cycle are the ORC bottoming cycle machinery and the coupled operation between the liquified air subsystem and the ORC subsystem. This paper presents modeling and simulation of the LACC that involves ORC conditions that fall outside the operating regime of more common applications. Due to the low temperatures of liquified air, the ORC system operates on the order of -70°C for the pump, and the turbine has a pressure ratio around 40. The conceptual design of a demonstration system has been developed that focuses on these challenges in order to advance the overall system.

Pryor, Owen↗
DOE OSTI2020

Combined Experimental/Numerical Study of the Soot Formation Process in a Gasoline Direct-Injection Spray in the Presence of Laser-Induced Plasma Ignition

Here, combustion issued from an eight-hole, direct-injection spray was experimentally studied in a constant-volume pre-burn combustion vessel using simultaneous high-speed diffused back-illumination extinction imaging (DBIEI) and OH* chemiluminescence. DBIEI has been employed to observe the liquid-phase of the spray and to quantitatively investigate the soot formation and oxidation taking place during combustion. The fuel-air mixture was ignited with a plasma induced by a single-shot Nd:YAG laser, permitting precise control of the ignition location in space and time. OH* chemiluminescence was used to track the high-temperature ignition and flame. The study showed that increasing the delay between the end of injection and ignition drastically reduces soot formation without necessarily compromising combustion efficiency. For long delays between the end of injection and ignition (1.9 ms) soot formation was eliminated in the main downstream charge of the fuel spray. However, poorly atomized and large droplets formed at the end of injection (dribble) eventually do form soot near the injector even when none is formed in the main charge. The quantitative soot measurements for these spray and ignition scenarios, resolved in time and space, represents a significant new achievement. Reynolds-averaged Navier-Stokes (RANS) simulations were performed to assess spray mixing and combustion. An analysis of the predicted fuel-air mixture in key regions, defined based upon experimental observations, was used to explain different flame propagation speeds and soot production tendencies when varying ignition timing. The mixture analysis indicates that soot production can be avoided if the flame propagates into regions where the equivalence ratio (Φ) is already below 2. Reactive RANS simulations have also been performed, but with a poor match against the experiment, as the flame speed and heat-release rate are largely over estimated. This modeling weakness appears related to a very high level of turbulent viscosity predicted for the high-momentum spray in the RANS simulations, which is an important consideration for modeling ignition and flame propagation in mixtures immediately created by the spray.

42 ENGINEERING↗
DOE OSTI2021

CFD-Guided Evaluation of Spark-Assisted Gasoline Compression Ignition for Cold Idle Operation

A closed-cycle, three-dimensional (3D) computational fluid dynamics (CFD) analysis campaign was conducted to evaluate the performance of using spark plugs to assist gasoline compression ignition (GCI) combustion during cold idle operations. A conventional spark plug using single-sided J-strap design was put at a location on the cylinder head to facilitate spray-guided spark assistance. Ignition was modeled with an L-type energy distribution to depict the breakdown and the arc-to-glow phases during the energy discharge process. Several key design parameters were investigated, including injector clocking, number of nozzle holes, spray inclusion angle, number of fuel injections, fuel split ratio, and fuel injection timings. The study emphasized the region around the spark gap, focusing on flame kernel formation and development and local equivalence ratio distribution. Flame kernel development and the ignition process were found to correlate strongly with the fuel stratification and the flow velocity near the spark gap. The analysis results showed that the flame kernel development followed the direction of the local flow field. In addition, the local fuel stratification notably influenced early-stage flame kernel development due to varying injection spray patterns and the fuel injection strategies. Among these design parameters, the number of nozzle holes and fuel injection timing had the most significant effects on the engine combustion performance.

42 ENGINEERING↗
DOE OSTI2021

Oxidation Behavior of Candidate NiCr Alloys for Engine Exhaust Valves: Part I—Effect of Minor Alloying Elements

Oxidation-induced degradation of structural materials employed as exhaust valves within internal combustion engines (ICEs) will be a relevant life-limiting mechanism, in addition to creep and mechanical fatigue, due to ever-increasing severity of operating temperatures and pressures. Ni–Cr-based alloys, which form external chromia-based scales at the relevant operating temperatures are being considered as suitable candidate materials. Thermal cycling of these alloys in water vapor-containing atmospheres, such as those present during hydrocarbon fuel combustion within ICEs, can considerably influence their oxidation behavior. Here, the role of typical alloying additions such as Mn, Si, Al and Ti on the cyclic oxidation behavior of model NiCr–X (X = Mn,Si,Al,Ti) alloys exposed in dry air and air + 10% H 2 O at 800°C and 950°C was investigated. Combined additions of Mn and Si reduced scaling rates compared to binary Ni–22Cr alloys. The presence of water vapor possibly suppressed formation of NiMnCr spinel and thereby the Cr depletion in the alloy. Combined Al and Ti additions mainly resulted in accelerated oxidation kinetics due to the Ti doping of chromia scales. More porous external scales were observed in water vapor leading to a much deeper depth of nitridation in the Ni–22Cr–Al–Ti alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Group additivity values for the heat of formation of C 2 –C 8 alkanes, alkyl hydroperoxides, and their radicals

A set of 58 group additivity values (GAV) for the calculation of the heat of formation is derived from an extensive and accurate database of 192 ab initio heats of formation. The ab initio values are from companion calculations at the CCSD(T)–F12/cc-pVTZ-F12//B2PLYPD3/cc-pVTZ level of theory employing second order connectivity based hierarchy reference reactions with ANL energies for the reference species. This database of 192 species consists of alkanes (RH), alkyl radicals ($\dot{\text {R}}$), alkyl hydroperoxides (RO 2 H), alkyl-peroxy (R$\dot{\text {O}}$ 2 ) radicals, and hydroperoxy-alkyl ($\dot{\text {Q}}$OOH) radicals of all of the isomers of C 2 –C 5 alkane fuels and a select set of C 6 –C 8 isomers. The GAV and ab initio based enthalpies for this dataset show excellent agreement, with an estimated 2σ uncertainty of 0.9 kcal mol –1 . Among the 58 GAV terms, 40 are refinements of previously reported terms, while 18 are newly developed. These new GAV terms are mainly non-next-nearest neighbor interactions (NNI) and β-corrections. The inclusion of these new groups significantly improves the accuracy of the GAV estimates of the heats of formation. Finally, the updated GAVs can be used with increased confidence to estimate the heats of formation of combustion relevant hydrocarbons and oxygenated hydrocarbons and their corresponding radicals, which are important in predicting low-temperature chemistry and are critical in the development of accurate chemical kinetic models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Comprehensive Kinetics on the C 7 H 7 Potential Energy Surface under Combustion Conditions

The automated kinetics workflow code, KinBot, was used to explore and characterize the regions of the C 7 H 7 potential energy surface that are relevant to combustion environments and especially soot inception. We first explored the lowest-energy region, which includes the benzyl, fulvenallene + H, and cyclopentadienyl + acetylene entry points. We then expanded the model to include two higher-energy entry points, vinylpropargyl + acetylene and vinylacetylene + propargyl. The automated search was able to uncover the pathways from the literature. In addition, three important new routes were discovered: a lower-energy pathway connecting benzyl with vinylcyclopentadienyl, a decomposition mechanism from benzyl that results in side-chain hydrogen atom loss to produce fulvenallene + H, and shorter and lower energy routes to the dimethylene-cyclopentenyl intermediates. We systematically reduced the extended model to a chemically relevant domain composed of 63 wells, 10 bimolecular products, 87 barriers, and 1 barrierless channel and constructed a master equation using the CCSD(T)-F12a/cc-pVTZ//ωB97X-D/6-311++G(d,p) level of theory to provide rate coefficients for chemical modeling. Our calculated rate coefficients show excellent agreement with measured ones. We also simulated concentration profiles and calculated branching fractions from the important entry points to provide an interpretation of this important chemical landscape.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗