Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Code Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Potential flow analysis of glaze ice accretions on an airfoil

The results of an analytical/experimental study of the flow fields about an airfoil with leading edge glaze ice accretion shapes are presented. Tests were conducted in the Icing Research Tunnel to measure surface pressure distributions and boundary layer separation reattachment characteristics on a general aviation wing section to which was affixed wooden ice shapes which approximated typical glaze ice accretions. Comparisons were made with predicted pressure distributions using current airfoil analysis codes as well as the Bristow mixed analysis/design airfoil panel code. The Bristow code was also used to predict the separation reattachment dividing streamline by inputting the appropriate experimental surface pressure distribution.

Zaguli, R. J.↗
NASA NTRS1984

Redesign and cascade tests of a supercritical controlled diffusion stator blade-section

A supercritical stator blade section, previously tested in cascade, and characterized by a flat-roof-top suction surface Mach number distribution, has been redesigned and retested. At near design conditions, the losses and air turning were improved over the original blade by 50 percent and 7 percent respectively. The key element in the improved performance was a small blade reshaping. This produced a continuous flow acceleration over the first one-third chord of the suction surface which successfully prevented a premature laminar separation bubble. Several recently available inviscid analysis and one fully viscous (Navier-Stokes) analysis code were used in the redesign process. The validity of these codes was enhanced by the test results.

Schmidt, J. F.↗
NASA NTRS1984

Development of MCAERO wing design panel method with interactive graphics module

A reliable and efficient iterative method has been developed for designing wing section contours corresponding to a prescribed subcritical pressure distribution. The design process is initialized by using MCAERO (MCAIR 3-D Subsonic Potential Flow Analysis Code) to analyze a baseline configuration. A second program DMCAERO is then used to calculate a matrix containing the partial derivative of potential at each control point with respect to each unknown geometry parameter by applying a first-order expansion to the baseline equations in MCAERO. This matrix is calculated only once but is used in each iteration cycle to calculate the geometry perturbation and to analyze the perturbed geometry. The potential on the new geometry is calculated by linear extrapolation from the baseline solution. This extrapolated potential is converted to velocity by numerical differentiation, and velocity is converted to pressure by using Bernoulli's equation. There is an interactive graphics option which allows the user to graphically display the results of the design process and to interactively change either the geometry or the prescribed pressure distribution.

Hawk, J. D.↗
NASA NTRS1984

Summary of recent NASA propeller research

Advanced high-speed propellers offer large performance improvements for aircraft that cruise in the Mach 0.7 to 0.8 speed regime. At these speeds, studies indicate that there is a 15 to near 40 percent block fuel savings and associated operating cost benefits for advanced turboprops compared to equivalent technology turbofan powered aircraft. Recent wind tunnel results for five eight to ten blade advanced models are compared with analytical predictions. Test results show that blade sweep was important in achieving net efficiencies near 80 percent at Mach 0.8 and reducing nearfield cruise noise by about 6 dB. Lifting line and lifting surface aerodynamic analysis codes are under development and some results are compared with propeller force and probe data. Also, analytical predictions are compared with some initial laser velocimeter measurements of the flow field velocities of an eightbladed 45 swept propeller. Experimental aeroelastic results indicate that cascade effects and blade sweep strongly affect propeller aeroelastic characteristics. Comparisons of propeller near-field noise data with linear acoustic theory indicate that the theory adequately predicts near-field noise for subsonic tip speeds but overpredicts the noise for supersonic tip speeds.

Mikkelson, D. C.↗
NASA NTRS1984

Aerodynamic design of the contoured wind-tunnel liner for the NASA supercritical, laminar-flow-control, swept-wing experiment

An overview is presented of the entire procedure developed for the aerodynamic design of the contoured wind tunnel liner for the NASA supercritical, laminar flow control (LFC), swept wing experiment. This numerical design procedure is based upon the simple idea of streamlining and incorporates several transonic and boundary layer analysis codes. The liner, presently installed in the Langley 8 Foot Transonic Pressure Tunnel, is about 54 ft long and extends from within the existing contraction cone, through the test section, and into the diffuser. LFC model testing has begun and preliminary results indicate that the liner is performing as intended. The liner design results presented in this paper, however, are examples of the calculated requirements and the hardware implementation of them.

Newman, P. A.↗
NASA NTRS1984

Steady state stresses in ribbon parachute canopies

An experimental study of the steady state stresses in model ribbon parachute canopies is presented. The distribution of circumferential stress was measured in the horizontal ribbons of two parachutes using Omega sensors. Canopy pressure distributions and overall drag were also measured. Testing was conducted in the University of Minnesota Low-Speed Wind Tunnel at dynamic pressures ranging from 1.0 to 1.5 inches of water. The stresses in the parachute canopies were calculated using the parachute structural analysis code, CANO. It was found that the general shape of the measured and calculated stress distributions was fairly similar; however, the measured stresses were somewhat less than the calculated stresses.

Garrard, W. L.↗
NASA NTRS1984

Analysis of axisymmetric body effects on rotor aerodynamics using modified slender body theory

A modified slender body theory was used in modelling the flowfield around an axisymmetric body at zero angle of attack. The model was defined in an attempt to characterize body-induced effects on helicopter rotor performance and loading using efficient computation methods. The streamfunction for an axial source distribution was applied in the body model, which was then adapted to the helicopter analysis code (CAMRAD). The body-induced velocities were calculated for separate locations on the rotor disk. Three different rotor models in nonuniform inflow with a free wake geometry were considered. Comparison of predictions with data on ellipsoidal and axisymmetric bodies showed good agreement for moderately thick ellipsoidal bodies. Oscillatory blade bending moments were increased by the presence of the body, but overall performance impact was negligible. Computational efficiency was 10-20 percent better than with a potential flow panel code.

Yamauchi, G. K.↗
NASA NTRS1984

Computer models and output, Spartan REM: Appendix B

A computer model of the Spartan Release Engagement Mechanism (REM) is presented in a series of numerical charts and engineering drawings. A crack growth analysis code is used to predict the fracture mechanics of critical components.

Marlowe, D. S.↗
NASA NTRS1984

Level of effort

The generation of a planar model of the ground test experiment structure is examined. This was done by adapting an in-house modal analysis code (Gimbalflex) to allow placement of sensors and actuators at certain locations on the structure. The next step in the development of this model was to adapt if for use with the control pole placement algorithm. The uncontrollable rigid body mode was removed from the model. This uncontrollable mode was due to the pointing of the gimbal. Control system design for the planar model was also initiated. A digital controller was planned utilizing the Control Pole Placement technique. The existence of rate of state feedback was assumed. Once this controller and other control algorithms were developed, it became necessary to conduct speed tests. A study was then made of additional hardware/software necessary to meet the speed requirement.

Source record↗
NASA NTRS1985

Summary of recent NASA propeller research

Advanced high speed propellers offer large performance improvements for aircraft that cruise in the Mach 0.7 to 0.8 speed regime. At these speeds, studies indicate that there is a 15 to near 40 percent block fuel savings and associated operating cost benefits for advanced turboprops compared to equivalent technology turbofan powered aircraft. Recent wind tunnel results for five eight to ten blade advanced models are compared with analytical predictions. Test results show that blade sweep was important in achieving net efficiencies near 80 percent at Mach 0.8 and reducing nearfield cruise noise about 6 dB. Lifting line and lifting surface aerodynamic analysis codes are under development and some results are compared with propeller force and probe data. Also, analytical predictions are compared with some initial laser velocimeter measurements of the flow field velocities of an eight bladed 45 swept propeller. Experimental aeroelastic results indicate that cascade effects and blade sweep strongly affect propeller aeroelastic characteristics. Comparisons of propeller nearfield noise data with linear acoustic theory indicate that the theory adequately predicts nearfield noise for subsonic tip speeds, but overpredicts the noise for supersonic tip speeds.

Mikkelson, D. C.↗
NASA NTRS1985

Burner liner thermal/structural load modeling: TRANCITS program user's manual

Transfer Analysis Code to Interface Thermal/Structural Problems (TRANCITS) is discussed. The TRANCITS code satisfies all the objectives for transferring thermal data between heat transfer and structural models of combustor liners and it can be used as a generic thermal translator between heat transfer and stress models of any component, regardless of the geometry. The TRANCITS can accurately and efficiently convert the temperature distributions predicted by the heat transfer programs to those required by the stress codes. It can be used for both linear and nonlinear structural codes and can produce nodal temperatures, elemental centroid temperatures, or elemental Gauss point temperatures. The thermal output of both the MARC and SINDA heat transfer codes can be interfaced directly with TRANCITS, and it will automatically produce stress model codes formatted for NASTRAN and MARC. Any thermal program and structural program can be interfaced by using the neutral input and output forms supported by TRANCITS.

Maffeo, R.↗
NASA NTRS1985

Computational wing design in support of an NLF variable sweep transition flight experiment

A natural laminar flow outer panel wing glove has been designed for a variable sweep fighter aircraft using state-of-the-art computational techniques. Testing of the design will yield wing pressure and boundary-layer data under actual flight conditions and environment. These data will be used to enhance the understanding of the interaction between crossflow and Tollmien-Schlichting disturbances on boundary-layer transition. The outer wing panel was contoured such that a wide range of favorable pressure gradients could be obtained on the wing upper surface. Extensive computations were performed to support the design effort which relied on two- and three-dimensional transonic design and analysis techniques. A detailed description of the design procedure that evolved during this study is presented. Results on intermediate designs at various stages in the design process demonstrate how the various physical and aerodynamic constraints were integrated into the design. Final results of the glove design analyzed as part of the complete aircraft configuration with a full-potential wing/body analysis code indicate that the aerodynamic design objectives were met.

Waggoner, E. G.↗
NASA NTRS1986

Divergence study of a high-aspect ratio, forward-swept wing

A study has been conducted in the NASA-Langley Transonic Dynamics wind tunnel to determine the divergence characteristics of a high aspect ratio forward swept wing of rectangular planform, for sweep angles of zero, -15, -30, -45, and -60 deg. In addition to a rectangular wingtip, a tip whose geometry lay parallel with the freestream flow was tested at a sweep angle of -45 deg. The primary objective was to obtain data that could be used to verify the divergence prediction capabilities of an aeroelastic analysis code employing kernel function aerodynamics. The analytical predictions of convergence were found to be conservative for all forward sweep angles, and the effect of the two tip shapes on divergence dynamic pressure were accurately predicted.

Cole, S. R.↗
NASA NTRS1986

Unified constitutive materials model development and evaluation for high-temperature structural analysis applications

Unified constitutive material models were developed for structural analyses of aircraft gas turbine engine hot section components with particular application to an isotropic material used for combustor liners. Differential forms of models independently developed were considered in this study. These models combine the interactions of time-dependent (creep) and time-independent (plasticity) inelastic behavior of a material. Predicted stress-strain responses from these models were evaluated against cyclic isothermal and nonisothermal test results for uniaxial specimens of a nickel-base superalloy. The unified models were implemented in a nonlinear structural analysis code. Two unique NASA Lewis test facilities were used in the evaluation of the models for complex geometry specimens and evaluation of advanced temperature and high-temperature strain measurement instrumentation. Predicted nonlinear structural responses from one of the models for a flat plate and a segment of a conventional combustor liner are presented.

Thompson, R. L.↗
NASA NTRS1987

Analysis of Solar Electrical and Thermal Systems

Report describes computer program for parametric analysis of alternative ways of generating heat and electrical power on satellite or spacecraft. Program, Solar Space Power Analysis Code (SOSPAC), examines changes in area, weight, and cost of generator system for changing conditions, in particular for changes in ratio of thermal to electrical outputs. Outlines execution procedure and presents sample set of input data. Gives example of mass and area calculations for sample data for each type of generator system and illustrates results with variety of charts.

Selcuk, M. Kudret↗
NASA NTRS1984

PIAS: A program for an iterative aeroelastic solution

A Program for an Iterative Aeroelastic Solution (PIAS) is discussed. This will be a modular computer program that combines the use of a finite-element structural analysis code with any linear or nonlinear aerodynamic code. At this point in time, PIAS has been designed but the software has not been written. The idea for this development originated with P. J. (Bud) Bobbitt of the NASA Langley Research Center. There was initial interest in an aeroelastic solution for a separation-induced leading-edge vortex. Some examples of the flow patterns for a low aspect ratio wing are shown. The Leading-Edge Vortex Program, which calculates pressure distributions including the effects of a separation-induced leading-edge vortex, uses an iterative solution method. This led to the concept of an iteration cycle on configuration shape external to the aerodynamic code.

Manro, M. E.↗
NASA NTRS1986

Stirling engine external heat system design with heat pipe heater

This final report presents the conceptual design of a liquid fueled external heating system (EHS) and the preliminary design of a heat pipe heater for the STM-4120 Stirling cycle engine, to meet the Air Force mobile electric power (MEP) requirement for units in the range of 20 to 60 kW. The EHS design had the following constraints: (1) Packaging requirements limited the overall system dimensions to about 330 mm x 250 mm x 100 mm; (2) Heat flux to the sodium heat pipe evaporator was limited to an average of 100 kW/m and a maximum of 550 kW/m based on previous experience; and (3) The heat pipe operating temperature was specified to be 800 C based on heat input requirements of the STM4-120. An analysis code was developed to optimize the EHS performance parameters and an analytical development of the sodium heat pipe heater was performed; both are presented and discussed. In addition, construction techniques were evaluated and scale model heat pipe testing performed.

Godett, Ted M.↗
NASA NTRS1987

Effects of local vibrations on the dynamics of space truss structures

The paper discusses the influence of local member vibrations on the dynamics of repetitive space truss structures. Several focus problems wherein local member vibration modes are in the frequency range of the global truss modes are discussed. Special attention is given to defining methods that can be used to identify the global modes of a truss structure amidst many local modes. Significant interactions between the motions of local member vibrations and the global behavior are shown to occur in truss structures when: (1) the natural frequencies of the individual members for clamped-clamped boundary conditions are in the vicinity of the global truss frequency; and (2) the total mass of the individual members represents a large portion of the mass of the whole structure. The analysis is carried out with a structural analysis code which uses exact member theory. The modeling detail required using conventional finite element codes to adequately represent such a class of problems is examined. The paper concludes with some practical considerations for the design and dynamic testing of structures which might exhibit such behavior.

Warnaar, Dirk B.↗