Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Cell Fabrication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Development and pilot line production of lithium doped silicon solar cells

The work performed over the period of September 1971 to August 1972 to develop production processes for fabrication of lithium doped P/N cells is described. The BCl3 diffusion without 02 was selected as the optimum diffusion process for fabrication of lithium doped cells. An 8-2-7 (warm up - deposition - drive-in time in minutes) diffusion schedule at 1055 C was used for the first two lots (300 cells each) delivered to JPL. Cell efficiencies ranged from 11.0 to 13.7% based on an AMO of 135.3 mW/sq cm. These high efficiencies were obtained using from 10 to 40 cells per boron diffusion; increasing the quantity beyond 40 resulted in lower outputs. At this point, the emphasis was placed on investigation of a BCl3 with 02 diffusion. Through evaluation of the effects of diffusion time and temperature, gas flow rates, and desposition plus drive-in vs. continuous deposition and no drive-in cycles, diffusion parameters were determined which produced short circuit currents of 136 + or - 4 mA for ten cells spaced along 12 in. of the diffusion boat. The quantity was increased to 60, 100, and 150 cell diffusions with no more variation in cell short circuit current than observed with 10 cells.

Payne, P. A.↗
DOE OSTI2021

Direct Deposition of Nonaqueous SnO 2 Dispersion by Blade Coating on Perovskites for the Scalable Fabrication of p–i–n Perovskite Solar Cells

Tin(IV) oxide materials have been extensively used as electron transport materials in n–i–p perovskite solar cells (PSCs) due to their superior optoelectronic properties, low-temperature processability, and high chemical stability. However, solvent incompatibility and processing temperature have limited the direct deposition of fully solution-processed SnO 2 in p–i–n devices. In this study, we overcome this limitation by the functionalization of SnO 2 nanoparticles with acetate through ligand exchange, allowing their dispersion in anhydrous ethanol. The SnO 2 dispersion was deposited on the perovskite absorber by blade coating without damaging the underlying perovskite layer, as determined by X-ray diffraction and scanning electron microscopy. Photoluminescence spectroscopy confirmed effective electron extraction. The champion device shows 14.1% initial power conversion efficiency (PCE) which is unprecedented for a p–i–n device employing solution-phase SnO 2 . Finally, PSCs stored for 40 days in a nitrogen flow box retained an average of 95.8% of the initial PCE.

14 SOLAR ENERGY↗
NASA NTRS1978

Fabrication and testing of silver-hydrogen cells

The development and life testing of single electrode and multi electrode stacks to optimize the individual components and characterize the performance of a silver hydrogen battery system are described. A NASA-developed inorganic separator material was used as the main separator within the cells. Single electrode test cells were cycled at 75% of nominal capacity out through approximately 1,000 cycles in a number of cases where deterioration in performance was observed. This deterioration appears to be a decay in usable capacity of the silver electrode; but the exact mechanism is still unidentified. Twenty ampere-hour boilerplate test cells consisting of a stack of ten silver electrodes and twenty hydrogen electrodes were cycled also at 75% depth of discharge. The oldest stack achieved 522 stable cycles to the end of the program. Weight analysis of light-weight cells showed that 50 ampere-hour cells with improved components could be capable of as much as 40 watt hours per pound.

Klein, M. G.↗
DOE OSTI2020

Novel platinum group metal-free catalyst ink deposition system for combinatorial polymer electrolyte fuel cell performance evaluation

Here, a new system for rapid and precise fabrication of polymer electrolyte fuel cell (PEFC) membrane-electrode assemblies (MEAs) is introduced to facilitate rapid testing and characterization of platinum group metal-free (PGM-free) catalysts, with minimal waste of materials, using commercial combinatorial hardware and multi-channel potentiostat. The commercial combinatorial system, designed for high-throughput catalyst activity evaluation (i.e., low overpotential and current densities) using gas-diffusion electrodes (GDEs), has been further developed to enable simultaneous evaluation of the high current density performance on air of twenty-five cathodes prepared by coating catalyst-ionomer inks directly onto the membrane using a newly-developed deposition system. A nanopipette or micropipette coupled to a precise peristaltic pump is being used for precise and even catalyst ink deposition onto the membrane in each of twenty-five circular electrodes with areas of <1 cm 2 and in the precise locations required by the commercial combinatorial MEA hardware. The automated ink deposition system is coupled with a custom-designed heated vacuum table mounted on a computer-controlled XY stage to prevent deformation of the membrane and electrode layers during ink deposition onto the membrane. This system was utilized to evaluate the impact of ionomer to catalyst ratio on the hydrogen-air fuel cell performance of the PGM-free catalyst.

25 ENERGY STORAGE↗
NASA NTRS1986

Evaluation studies on carbon supported catalysts for oxygen reduction in alkaline medium

This paper describes tests designed to predict the performance of fuel cell electrodes, as applied to an alkaline oxygen-fuel cell having specially fabricated porous-carbon electrodes with various amounts of dispersed platinum or gold as active catalysts. The tests are based on information obtained from the techniques of cyclic voltammetry and polarization. The parameters obtained from cyclic voltammetry were of limited use in predicting fuel cell performance of the cathode. On the other hand, half-cell polarization measurements offered close simulation of the oxygen electrode, although a predictor of the electrode life is still lacking. The very low polarization of the Au-10 percent Pt catalytic electrode suggests that single-phase catalysts should be considered.

Srinivasan, Vakula S.↗
DOE OSTI2020

Emergent Degradation Phenomena Demonstrated on Resilient, Flexible, and Scalable Integrated Photoelectrochemical Cells

Photoelectrochemical (PEC) water splitting provides a pathway to generate sustainable clean fuels using the two most abundant resources on Earth: sunlight and water. Currently, most of the successful models of PEC cells are still fabricated on small scales near 1 cm 2 , which largely limits the mass deployment of solar-fuel production. Here, the scale-up to 8 cm 2 of an integrated PEC (IPEC) device is demonstrated and its performance compared to a 1 cm 2 IPEC cell, using state-of-the-art iridium and platinum catalysts with III–V photoabsorbers. The initial photocurrents at 1 sun are 8 and 7 mA cm -2 with degradation rates of 0.60 and 0.47 mA cm -2 day -1 , during unbiased operation for the 1 and 8 cm 2 devices, respectively. Additionally, evaluating under outdoor and indoor conditions at two U.S. National Laboratories reveals similar results, evidencing the reproducibility of this design's performance. Furthermore, the emerging degradation mechanisms during scale-up are investigated and the knowledge gained from this work will provide feedback to the broader community, since PEC device durability is a limiting factor in its potential future deployment.

25 ENERGY STORAGE↗
DOE OSTI2020

Water Splitting: Emergent Degradation Phenomena Demonstrated on Resilient, Flexible, and Scalable Integrated Photoelectrochemical Cells (Adv. Energy Mater. 48/2020)

We report Photoelectrochemical (PEC) water splitting provides a pathway to generate sustainable clean fuels using the two most abundant resources on Earth: sunlight and water. Currently, most of the successful models of PEC cells are still fabricated on small scales near 1 cm 2 , which largely limits the mass deployment of solar-fuel production. Here, the scale-up to 8 cm 2 of an integrated PEC (IPEC) device is demonstrated and its performance compared to a 1 cm 2 IPEC cell, using state-of-the-art iridium and platinum catalysts with III-V photoabsorbers. The initial photocurrents at 1 sun were 8 and 7 mA cm -2 with degradation rates of 0.60 and 0.47 mA cm -2 day -1 , during unbiased operation for the 1 and 8 cm 2 devices, respectively. Evaluating under outdoor and indoor conditions at two US National Laboratories revealed similar results, evidencing the reproducibility of this design’s performance. Furthermore, the emerging degradation mechanisms during scale-up are investigated and the knowledge gained from this work will provide feedback to the broader community, since PEC device durability is a limiting factor in its potential future deployment.

25 ENERGY STORAGE↗
NASA NTRS1971

Optimized silicon solar cells for space exploration power systems

A program is described aimed at designing and fabricating improved silicon solar cells for a range of missions extending from 0.1 to 15 astronomical units (Mercury to Jupiter). For missions lying inside Earth radius (Mercury, Venus) the major cell property required was very low series resistance, allowing high curve fill factor to be maintained at the higher intensities. For the Mercury mission, the temperature of the cell had to be kept low. This was achieved by reflecting more of the incident sunlight by use of large area front contacts. For the outer missions (Mars, the Asteroid belts and Jupiter) the formation of a Schottky barrier at the back contact had to be avoided (by use of a P+ layer under the back contact) and the excess leakage current of the PN junction had to be reduced. Optimum grid patterns were also derived and used for these missions.

Iles, P. A.↗
DOE OSTI2021

A chemical switch enabled autonomous two-stage crosslinking polymeric binder for high performance silicon anodes

Silicon (Si) is a promising high-capacity anode material for high-energy-density lithium-ion batteries. However, the drastic volumetric changes of Si upon lithiation/delithiation hinder the practical use of Si anodes. Although adhesive polymeric binders, such as poly(acrylic acid) (PAA), mitigate this issue, the cycling performance of the fabricated Si anodes is still far from meeting the criteria of practical applications. In this study, we present a novel polymeric binder system for Si anodes consisting of PAA, a chemical switch (ammonia, NH 3 ), and a crosslinker (branched polyethylenimine, PEI). The crosslinking between PAA and PEI is switched off in the slurry, which can then be turned on during electrode drying. Interestingly, the crosslinking reaction consists of two stages: ionic cross-linking (PAA-PEI-i) and covalent crosslinking (PAA-PEI-c) at a higher temperature (e.g., 130 °C). In half-cells, Si anodes fabricated using the PAA-PEI-c binder show a 67% increase in capacity retention compared to PAA anodes over 150 cycles at C/3 rate. The PAA-PEI-c binder also outperforms PAA in full cells. In addition, the chemical switch controlled crosslinking binder system also facilitates the slurry making process by avoiding early crosslinking. This system requires no additional steps compared to the conventional electrode lamination process, showing enormous potential for direct adoption in large-scale manufacturing.

25 ENERGY STORAGE↗
NASA NTRS1976

Optimization of contaminated oxide inversion layer solar cell

Contaminated oxide cells have been fabricated with efficiencies of 8.6% with values of I sub sc = 120 ma, V sub oc = .54 volts, and curve factor of .73. Attempts to optimize the fabrication step to yield a higher output have not been successful. The fundamental limitation is the inadequate antireflection coating afforded by the silicon dioxide coating used to hold the contaminating ions. Coatings of SiO, therefore, were used to obtain a good antireflection coating, but the thinness of the coatings prevented a large concentration of the contaminating ions, and the cells was weak. Data of the best cell were .52 volts V sub oc, 110 ma I sub sc, .66 CFF and 6.7% efficiency.

Call, R. L.↗
NASA NTRS1978

Conceptual approach study 200 watt per kilogram solar array, phase 3

Activities are described that were directed by JPL to support the earlier conceptual design work with proof of concept models on the one hand, and laboratory test and evaluation of alternate designs and materials that hold promise for further mass economies, on the other. In support of this advanced solar blanket technology the following work was accomplished: (1) preparation of an 80 cell solar module for a 1000 cycle thermal test (2) fabrication of a 660 cell solar panel and performance evaluation of this article after a '0' g flight test, (3) design improvement of the cell interconnect for further mass reduction, (4) completion of UV exposure and thermal cycle tests for a variety of cell cover material and adhesives and (5) preparation of a quantity of representative solar array test specimens for space flight on NASA's Long Duration Exposure Facility (LDEF).

Rayl, G. J.↗
NASA NTRS1980

Solar cell system having alternating current output

A monolithic multijunction solar cell was modified by fabricating an integrated circuit inverter on the back of the cell to produce a device capable of generating an alternating current output. In another embodiment, integrated curcuit power conditioning electronics was incorporated in a module containing a solar cell power supply.

Evans, J. C., Jr.↗
NASA NTRS1990

Monolithic and mechanical multijunction space solar cells

Monolithic and mechanically stacked tandem solar cells have been fabricated with encouraging AM0 efficiencies summarized as: monolithic GaAs/Ge: 19.1 percent (28 C, 4 sq cm); monolithic InP/Ga0.47In0.53As: 22.2 percent (25 C, 0.296 sq cm); monolithic AlGaAs/GaAs/InGaAs: 27.6 percent (80 C, 0.2 sq cm, 100 X); mechanically stacked GaAs/GaSb: 30.8 percent (25 C, 0.049 sq cm, 100 X); and mechanically stacked GaAs/CuInSe2: 23.1 percent (25 C, 4 sq cm). Significant improvement in tandem cell efficiencies nearing to theoretical predictions has been projected with the improvement in cell material quality and processing. Thin-film cells offer improved specific power. It is pointed out that both the monolithic and mechanically stacked cells have their own problems as to size, processing, current-voltage matching, weight, etc. More information is needed on the effect of temperature and radiation on the cell performance. Proper reference cells and full spectrum range simulators are required to measure efficiencies correctly.

Jain, Raj K.↗
NASA NTRS1981

Application of laser annealing to solar cell junction formation

The possibility of using high-energy Q-switched Nd:glass lasers to form pn junctions in solar cells by annealing ion-implanted substrates is investigated. The properties of laser annealed cells are analyzed by electrical, transmission electron microscopy, Rutherford backscattering and secondary ion mass spectrometry techniques. Tests indicate the laser annealed substrates to be damage-free and electrically active. Similar reference analysis of ion-implanted furnace-annealed substrates reveals the presence of residual defects in the form of dislocation lines and loops with substantial impurity redistribution evident for some anneal temperature/time regimes. Fabricated laser annealed cells exhibit excellent conversion efficiency. It is noted that additional improvements are anticipated once the anneal parameters for a back surface field are optimized.

Katzeff, J. S.↗
NASA NTRS2007

Ultra-Lightweight Hybrid Thin-Film Solar Cells: A Survey of Enabling Technologies for Space Power Applications

The development of hybrid inorganic/organic thin-film solar cells on flexible, lightweight, space-qualified, durable substrates provides an attractive solution for fabricating solar arrays with high mass specific power (W/kg). Next generation thin-film technologies may well involve a revolutionary change in materials to organic-based devices. The high-volume, low-cost fabrication potential of organic cells will allow for square miles of solar cell production at one-tenth the cost of conventional inorganic materials. Plastic solar cells take a minimum of storage space and can be inflated or unrolled for deployment. We will explore a cross-section of in-house and sponsored research efforts that aim to provide new hybrid technologies that include both inorganic and polymer materials as active and substrate materials. Research at University of Texas at Arlington focuses on the fabrication and use of poly(isothianaphthene-3,6-diyl) in solar cells. We describe efforts at Norfolk State University to design, synthesize and characterize block copolymers. A collaborative team between EIC Laboratories, Inc. and the University of Florida is investigating multijunction polymer solar cells to more effectively utilize solar radiation. The National Aeronautics and Space Administration (NASA)/Ohio Aerospace Institute (OAI) group has undertaken a thermal analysis of potential metallized substrates as well as production of nanoparticles of CuInS2 and CuInSe2 in good yield at moderate temperatures via decomposition of single-source precursors. Finally, preliminary work at the Rochester Institute of Technology (R.I.T.) to assess the impact on performance of solar cells of temperature and carbon nanotubes is reported. Technologies that must be developed to enable ultra-lightweight solar arrays include: monolithic interconnects, lightweight array structures, and new ultra-light support and deployment mechanisms. For NASA applications, any solar cell or array technology must not only meet weight and AMO efficiency goals, but also must be durable enough to survive launch conditions and space environments.

Hepp, Aloysius F.↗
DOE OSTI2023

Efficient and stable perovskite solar cells based on blade-coated CH 3 NH 3 PbI 3 thin films fabricated using “green” solvents under ambient conditions

Metal halide perovskites are considered the most promising candidates for solar cells of the decade due to their exceptional optical and electronic properties. The power conversion efficiency of metal halide perovskites, when incorporated as the active layer of solar cells, has become comparable to that observed for conventional silicon solar cells. However, the stability, scaleup, green solvent usage, and fabrication in ambient conditions of metal halide perovskites need to be solved for commercial applications. Here, in this work, we report the fabrication of blade-coated methylammonium lead iodide (MAPbI 3 ) perovskite thin films using methylamine and acetonitrile as “green” solvents under ambient conditions. Our perovskite films are initially prepared from low purity PbI2 (99%) and are blade-coated in dry air at relative humidity (RH) levels above 30%. A significant advantage of fabricating our perovskite thin films via blade-coating protocols is that there is a minimal amount of precursors (5 μL) used compared to spin-coating methods (50μL–60μL) for a 4 cm 2 substrate. With the addition of a small amount of an organic halide salt, namely, phenethylammonium chloride, the film crystallinity is improved and non-radiative recombination is suppressed, resulting in power conversion efficiencies over 20%. In addition, the device maintains more than 95% of its initial efficiency after 500 h under continuous light illumination of 1-sun at open circuit conditions, 50 °C and 60% RH. The above method leads a path towards the commercial fabrication of perovskite solar cells.

14 SOLAR ENERGY↗