Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38

A Low-Temperature, Solution-Processable, Cu-Doped Nickel Oxide Hole-Transporting Layer via the Combustion Method for High-Performance Thin-Film Perovskite Solar Cells

The promising photophysical properties of the emerging organometallic halide perovskites, such as intense broadband absorption, high charge carrier mobility, and long charge diffusion length, have enabled the rapid development in solar cells reaching over 20% power conversion effi ciency (PCE) recently. Especially, the low material cost and facile solution processability of perovskites are very attractive as next-generation photovoltaic materials for sustainable energy.

14 SOLAR ENERGY↗

Gasoline fuels properties for multi-mode operation – Observations in a GDI and the CFR engine

The combustion behavior of five full boiling range RON98 gasoline blends was evaluated for multi-mode operation in a GDI and the CFR octane rating engine. The GDI engine tests were conducted with stoichiometric air-fuel ratio in spark-ignition (SI), and with air-diluted homogeneous charge compression ignition (HCCI) mode. In the CFR engine, the knocking combustion was analyzed under standard RON testing conditions at both peak knocking lambda and stoichiometric air-fuel ratios, whereas compression ignited operation was characterized by utilizing the HCCI number test protocol. Disparate knock limited SI and HCCI combustion behavior was observed for the test fuels, despite four of the fuels having the same RON and octane sensitivity. It was found that knock-limited combustion phasing in the GDI engine did not align well with the RON. However, a detailed comparison of knock-limited SI operation in the GDI and CFR engine revealed that a more appropriate effective RON based on a common knock intensity metric (MAPO) and stoichiometric air-fuel ratio resulted in comparable knock characterization between the two engine platforms. Furthermore, the critical intake air temperature and the critical compression ratio were proposed to characterize knock-limited SI operation, while the minimum intake air heating and compression ratio were used to define a fuel's autoignition propensity for compression ignition operation in the GDI and CFR engine, respectively. Finally, each fuel's characteristic compression ratio needed to obtain knock-limited SI (KLSI) and HCCI operation was used to calculate an effective multi-mode octane number (MM-ON) based on the primary reference fuel blends.

33 ADVANCED PROPULSION SYSTEMS↗

Climatological Aspects of the Optical Properties of Fine/Coarse Mode Aerosol Mixtures

Aerosol mixtures composed of coarse mode desert dust combined with fine mode combustion generated aerosols (from fossil fuel and biomass burning sources) were investigated at three locations that are in and/or downwind of major global aerosol emission source regions. Multiyear monitoring data at Aerosol Robotic Network sites in Beijing (central eastern China), Kanpur (Indo-Gangetic Plain, northern India), and Ilorin (Nigeria, Sudanian zone of West Africa) were utilized to study the climatological characteristics of aerosol optical properties. Multiyear climatological averages of spectral single scattering albedo (SSA) versus fine mode fraction (FMF) of aerosol optical depth at 675 nm at all three sites exhibited relatively linear trends up to 50% FMF. This suggests the possibility that external linear mixing of both fine and coarse mode components (weighted by FMF) dominates the SSA variation, where the SSA of each component remains relatively constant for this range of FMF only. However, it is likely that a combination of other factors is also involved in determining the dynamics of SSA as a function of FMF, such as fine mode particles adhering to coarse mode dust. The spectral variation of the climatological averaged aerosol absorption optical depth (AAOD) was nearly linear in logarithmic coordinates over the wavelength range of 440-870 nm for both the Kanpur and Ilorin sites. However, at two sites in China (Beijing and Xianghe), a distinct nonlinearity in spectral AAOD in logarithmic space was observed, suggesting the possibility of anomalously strong absorption in coarse mode aerosols increasing the 870 nm AAOD.

Eck, T. F.↗

Broad Specification Fuels Combustion Technology Program, Phase 2

An experimental evaluation of two advanced technology combustor concepts was conducted to evolve and assess their capability for operation on broadened properties fuels. The concepts were based on the results of Phase 1 of the Broad Specification Fuel Combustor Technology Program which indicated that combustors with variable geometry or staged combustion zones had a flexibility of operation that could facilitate operation on these fuels. Emphasis in defining these concepts included the use of single pipe as opposed to duplex or staged fuels systems to avoid the risk of coking associated with the reduction in thermal stability expected in broadened properties fuels. The first concept was a variable geometry combustor in which the airflow into the primary zone could be altered through valves on the front while the second was an outgrowth of the staged Vorbix combustor, evolved under the NASA/P&W ECCP and EEE programs incorporating simplified fuel and air introduction. The results of the investigation, which involved the use of Experimental Referee Broad Specification (ERBS) fuel, indicated that in the form initially conceived, both of these combustor concepts were deficient in performance relative to many of the program goals for performance emissions. However, variations of both combustors were evaluated that incorporated features to simulate conceptual enhancement to demonstrate the long range potential of the combustor. In both cases, significant improvements relative to the program goals were observed.

Lohmann, R. P.↗

Synthesis of submicron CaZrO{sub 3} in combustion reactions

Submicron CaZrO{sub 3} powder is obtained in combustion reactions (solution combustion synthesis—SCS) with glycine. It is found that SCS reduces the sintering temperature of CaZrO{sub 3} powders. The dielectric properties of calcium zirconate ceramics are studied by the electrochemical impedance method. It is shown that a ceramics of powders obtained by the SCS method has high dielectric characteristics.

36 MATERIALS SCIENCE↗

Combustion-related pollutants of polydisperse single-composition aerosols and advection fog formation

The most noticeable effect of air pollution on the properties of the atmosphere is the reduction in visibility, with and without the occurrence of condensation, which frequently accompanies polluted air. The present study concerns the formation of advection fog associated with aerosols, due to combustion-related pollutants, with a polydisperse population distribution and a single composition model. The results show that an aerosol population with high particle concentration-shifted distribution provides a more favorable condition for the formation of dense fog than an aerosol population with a low particle concentration-shifted distribution if the value of the mass concentration of the aerosols is kept constant.

Hung, R. J.↗

Structure and Reactivity of Low-Rank Coal Chars Prepared from Fluidized Bed and Moving Bed Pyrolyzers and the Potential for Using Them in Pulverized Coal Injection (PCI)

Utilizing pyrolysis chars as the injection fuel in a blast furnace can reduce the dependence on high-quality pulverized coal injection (PCI) coal. In this study, the physical properties and reaction characteristics of chars prepared from two different industrial-scale pyrolyzers (fluidized bed and moving bed) are investigated. The results reveal remarkable component segregation in the char particles with different particle sizes. The properties of large-size char particles are found to better satisfy the PCI fuel requirement in a blast furnace. Compared with PCI coal, the char particles exhibit a rough surface, well-developed pore structure, and less-ordered chemical structure of carbon. Results from isothermal combustion, isothermal gasification, and drop tube furnace experiments show that both types of chars exhibit a better reactivity than PCI coal. The excellent reactivity of chars is closely related to its high Brunauer–Emmett–Teller surface area and relatively poor chemical ordering during conversion. Based on these characteristics, both fluidized bed char (FBC) and moving bed char (MBC) have a great potential to be used as PCI fuels. The application method of chars for PCI in a blast furnace is proposed finally.

01 COAL, LIGNITE, AND PEAT↗

A perspective on the range of gasoline compression ignition combustion strategies for high engine efficiency and low NOx and soot emissions: Effects of in-cylinder fuel stratification

Many research studies have shown that low temperature combustion in compression ignition engines has the ability to yield ultra-low NOx and soot emissions while maintaining high thermal efficiency. To achieve low temperature combustion, sufficient mixing time between the fuel and air in a globally dilute environment is required, thereby avoiding fuel-rich regions and reducing peak combustion temperatures, which significantly reduces soot and NOx formation, respectively. It has been demonstrated that achieving low temperature combustion with diesel fuel over a wide range of conditions is difficult because of its properties, namely, low volatility and high chemical reactivity. On the contrary, gasoline has a high volatility and low chemical reactivity, meaning it is easier to achieve the amount of premixing time required prior to autoignition to achieve low temperature combustion. In order to achieve low temperature combustion while meeting other constraints, such as low pressure rise rates and maintaining control over the timing of combustion, in-cylinder fuel stratification has been widely investigated for gasoline low temperature combustion engines. The level of fuel stratification is, in reality, a continuum ranging from fully premixed (i.e. homogeneous charge of fuel and air) to heavily stratified, heterogeneous operation, such as diesel combustion. However, to illustrate the impact of fuel stratification on gasoline compression ignition, the authors have identified three representative operating strategies: partial, moderate, and heavy fuel stratification. Thus, this article provides an overview and perspective of the current research efforts to develop engine operating strategies for achieving gasoline low temperature combustion in a compression ignition engine via fuel stratification. In this paper, computational fluid dynamics modeling of the in-cylinder processes during the closed valve portion of the cycle was used to illustrate the opportunities and challenges associated with the various fuel stratification levels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantitative measurement of oxygen in microgravity combustion

This research combines two innovations in an experimental system which should result in a new capability for quantitative, nonintrusive measurement of major combustion species. Using a newly available vertical cavity surface-emitting diode laser (VCSEL) and an improved spatial scanning method, we plan to measure the temporal and spatial profiles of the concentrations and temperatures of molecular oxygen in a candle flame and in a solid fuel (cellulose sheet) system. The required sensitivity for detecting oxygen is achieved by the use of high frequency wavelength modulation spectroscopy (WMS). Measurements will be performed in the NASA Lewis 2.2-second Drop Tower Facility. The objective of this research is twofold. First, we want to develop a better understanding of the relative roles of diffusion and reaction of oxygen in microgravity combustion. As the primary oxidizer species, oxygen plays a major role in controlling the observed properties of flames, including flame front speed (in solid or liquid flames), extinguishment characteristics, flame size, and flame temperature. The second objective is to develop better diagnostics based on diode laser absorption which can be of real value in microgravity combustion research. We will also demonstrate diode lasers' potential usefulness for compact, intrinsically-safe monitoring sensors aboard spacecraft. Such sensors could be used to monitor any of the major cabin gases as well as important pollutants.

Silver, Joel A.↗

Demonstration of Multi-Gamma Based Sensor Technology for As-Fired Coal Property Measurement

This project demonstrated the application of the use of an advanced multigamma attenuation (MGA) sensor to accurately and precisely measure coal properties at the point of injection into burners. Accurate and precise coal property information at the burner provides the opportunity to adjust burner parameters to better follow changing load condition, optimize flame stability, and decrease nitrogen oxide formation at each burner. In addition, coal property information at the burner will assist in managing slag flow behavior, fireside ash related deposition, corrosion, and erosion issues. The advantage of having multiple gamma emitters is that the atomic/elemental interaction with the gamma energy takes place at several energies and the resulting attenuation is dependent upon the atomic number of the atom/element encountered in the coal.

01 COAL, LIGNITE, AND PEAT↗

Optimization and purification of magnesium borides fabricated by combustion synthesis and by high-temperature sintering

Hydrogen as a fuel provides several benefits over the use of fossil fuels; however, one challenge in utilizing hydrogen as an energy carrier revolves around its storage. Achieving sufficient volumetric hydrogen density in a storage solution will facilitate hydrogen’s adoption for use in both stationary and mobile applications. Solid-state hydrogen storage provides a promising pathway to solving this problem. However, the hydrogenation of these materials is characterized by slow kinetics and extreme thermodynamic conditions. Magnesium borohydride (Mg(BH4)2) is a promising material in hydrogen storage due to its reversible properties and a theoretical hydrogen capacity of 14.9 wt.%. To synthesize this material, combustion synthesis of magnesium borides (MgBx) has been implemented with the aim to further lower thermodynamic requirements for direct hydrogenation. A drawback of this process is the potential formation of oxide contaminants, which decrease hydrogenation/dehydrogenation and recyclability performance. The present work focuses on identifying parameters useful for reducing contamination and evaluating potential pathways to the purification of magnesium borides with the goal of improving their quality.

Camarena, Miguel Joaquin↗

Hybrid rocket combustion study

The objectives of this study of 'pure' or 'classic' hybrids are to (1) extend our understanding of the boundary layer combustion process and the critical engineering parameters that define this process, (2) develop an up-to-date hybrid fuel combustion model, and (3) apply the model to correlate the regression rate and scaling properties of potential fuel candidates. Tests were carried out with a hybrid slab window motor, using several diagnostic techniques, over a range of motor pressure and oxidizer mass flux conditions. The results basically confirmed turbulent boundary layer heat and mass transfer as the rate limiting process for hybrid fuel decomposition and combustion. The measured fuel regression rates showed good agreement with the analytical model predictions. The results of model scaling calculations to Shuttle SRM size conditions are presented.

Strand, L. D.↗

Low-Temperature Magnetic Properties of Vanadium-Doped ZnO Nanoparticles

Low-temperature magnetic study of transition metal-doped ZnO nanoparticles tends to spring ambiguities of magnetic phases due to defect states, environment of doped ions, and anisotropy. Interestingly, vanadium doping in ZnO brings out versatile magnetic ordering which offers more room for basic understanding of the underlying mechanism. Vanadium-doped ZnO nanoparticles are prepared using a simple cost-effective approach of solution combustion method. Macroscopic and microscopic aspects of the samples have been unraveled using structural and morphological studies with the implications on the exhibited magnetic behavior. Development of antiferromagnetic, ferromagnetic, and ferrimagnetic interactions in the material illustrated by low-temperature magnetic measurements preludes the possible interplay of dopant-initiated defect correlation and morphological and interfacial secondary phases. The grain boundary reformation due to vanadium in the ZnO nanograins is exploited through a systematic correlation of structural and morphological studies in order to gain more insight into the portrayed magnetic signatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Numerical study on the spark ignition characteristics of a methane-air mixture using detailed chemical kinetics. Effect of equivalence ratio, electrode gap distance, and electrode radius on MIE, quenching distance, and ignition delay

The minimum ignition energy (MIE) is an important property for designing safety standards and understanding the ignition process of combustible mixtures. Even though the formation of flame kernels in quiescent methane-air mixtures has been simulated numerically, the ignition mechanism has never been satisfactorily explained. This study investigated the spark ignition of methane-air mixtures through a numerical analysis using detailed chemical kinetics consisting of 53 species and 325 elementary reactions while considering the heat loss to the electrode. The simulation was used to investigate the quenching distance and the effects on the MIE of the electrode size, electrode gap distance, ignition duration, and equivalence ratio. The effect of the equivalence ratio on the ignition delay time was also examined. The simulated results showed the same trend as previous experimental results. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Fractional condensation of pyrolysis vapors produced from Nordic feedstocks in cyclone pyrolysis

Pyrolysis oil is a complex mixture of different chemical compounds with a wide range of molecular weights and boiling points. Due to its complexity, an efficient fractionation of the oil may be a more promising approach of producing liquid fuels and chemicals than treating the whole oil. In this work a sampling system based on fractional condensation was attached to a cyclone pyrolysis pilot plant to enable separation of the produced pyrolysis vapors into five oil fractions. The sampling system was composed of cyclonic condensers and coalescing filters arranged in series. Our objective was to characterize the oil fractions produced from three different Nordic feedstocks and suggest possible applications. The oil fractions were thoroughly characterized using several analytical techniques including water content; elemental composition; heating value, and chemical compound group analysis using solvent fractionation, quantitative 13 C NMR and 1 H NMR and GC x GC - TOFMS. The results show that the oil fractions significantly differ from each other both in chemical and physical properties. The first fractions and the fraction composed of aerosols were highly viscous and contained larger energy-rich compounds of mainly lignin-derived material. The middle fraction contained medium-size compounds with relatively high concentration of water, sugars, alcohols, hydrocarbonyls and acids and finally the last fraction contained smaller molecules such as water, aldehydes, ketones and acids. But, the properties of the respective fractions seem independent on the studied feedstock types, i.e. the respective fractions produced from different feedstock are rather similar. Furthermore, this promotes the possibility to vary the feedstock depending on availability while retaining the oil properties. Possible applications of the five fractions vary from oil for combustion and extraction of the pyrolytic lignin in the early fractions to extraction of sugars from the early and middle fractions, and extraction of acids and aldehydes in the later fractions.

09 BIOMASS FUELS↗

A Theoretical Study of Methanol Oxidation on RuO 2 (110): Bridging the Pressure Gap

Partial oxidation catalysis is often fraught with selectivity problems, largely because there is a tendency of oxidation products to be more reactive than the starting material. One industrial process that has successfully overcome this problem is partial oxidation of methanol to formaldehyde. This process has become a global success, with an annual production of 30 million tons. Although ruthenium catalysts have not shown activity as high as the current molybdena or silver-based industrial standards, the study of ruthenium systems has the potential to elucidate which catalyst properties facilitate the desired partial oxidation reaction as opposed to deep combustion due to a pressure-dependent selectivity “switch” that has been observed in ruthenium-based catalysts. In this work, we find that we are able to successfully rationalize this “pressure gap” using near-ab initio steady-state microkinetic modeling on RuO 2 (110). We obtain molecular desorption prefactors from experiment and determine all other energetics using density functional theory. We show that, under ambient pressure conditions, formaldehyde production is favored on RuO 2 (110), whereas under ultrahigh vacuum pressure conditions, full combustion to CO 2 takes place. We glean from our model several insights regarding how coverage effects, oxygen activity, and rate-determining steps influence selectivity and activity. As a result, we believe the understanding gained in this work might advise and inspire the greater partial oxidation community and be applied to other catalytic processes which have not yet found industrial success.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A machine learning approach for determining temperature-dependent bandgap of metal oxides utilizing Allen–Heine–Cardona theory and O’Donnell model parameterization

To evaluate the high temperature sensing properties of metal oxide and perovskite materials suitable for use in combustion environments, it is necessary to understand the temperature dependence of their bandgaps. Although such temperature-driven changes can be calculated via the Allen–Heine–Cardona (AHC) theory, which assesses electron–phonon coupling for the bandgap correction at given temperatures, this approach is computationally demanding. Another approach to predict bandgap temperature-dependence is the O’Donnell model, which uses analytical expressions with multiple fitting parameters that require bandgap information at 0 K. This work employs data-driven Gaussian process regression (GPR) to predict the parameters employed in the O’Donnell model from a set of physical features. We use a sample of 54 metal oxides for which density functional theory has been performed to calculate the bandgap at 0 K, and the AHC calculations have been carried out to determine the shift in the bandgap at non-zero temperatures. As the AHC calculations are impractical for high-throughput screening of materials, the developed GPR model attempts to alleviate this issue by predicting the O'Donnell parameters purely from physical features. To mitigate the reliability issues arising from the very small size of the dataset, we apply a Bayesian technique to improve the generalizability of the data-driven models as well as quantify the uncertainty associated with the predictions. The method captures well the overall trend of the O’Donnell parameters with respect to a reduced feature set obtained by transforming the available physical features. Quantifying the associated uncertainty helps us understand the reliability of the predictions of the O’Donnell parameters and, therefore, the bandgap as a function of temperature for any novel material.

36 MATERIALS SCIENCE↗

Integrating plant physiology into simulation of fire behavior and effects

Summary Wildfires are a global crisis, but current fire models fail to capture vegetation response to changing climate. With drought and elevated temperature increasing the importance of vegetation dynamics to fire behavior, and the advent of next generation models capable of capturing increasingly complex physical processes, we provide a renewed focus on representation of woody vegetation in fire models. Currently, the most advanced representations of fire behavior and biophysical fire effects are found in distinct classes of fine‐scale models and do not capture variation in live fuel (i.e. living plant) properties. We demonstrate that plant water and carbon dynamics, which influence combustion and heat transfer into the plant and often dictate plant survival, provide the mechanistic linkage between fire behavior and effects. Our conceptual framework linking remotely sensed estimates of plant water and carbon to fine‐scale models of fire behavior and effects could be a critical first step toward improving the fidelity of the coarse scale models that are now relied upon for global fire forecasting. This process‐based approach will be essential to capturing the influence of physiological responses to drought and warming on live fuel conditions, strengthening the science needed to guide fire managers in an uncertain future.

54 ENVIRONMENTAL SCIENCES↗