Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Boundary Layer Profiles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Convection wave studies over land and sea

Preliminary results of recent case studies conducted over land and sea are given. Two dimensional convection (roll vortex/cloudstreet) and three dimensional convection in the underlying boundary layer are dealt with. Vertical momentum flux profiles and time series of important parameters and vertical soundings taken in the experiment area are shown. The three cases described show that convection waves occur over land and over ocean, over three dimensional convection and over two dimensional convection.

Kuettner, Joachim↗
NASA NTRS1993

Application of CFD to a generic hypersonic flight research study

Computational analyses have been performed for the initial assessment of flight research vehicle concepts that satisfy requirements for potential hypersonic experiments. Results were obtained from independent analyses at NASA Ames, NASA Langley, and Sandia National Labs, using sophisticated time-dependent Navier-Stokes and parabolized Navier-Stokes methods. Careful study of a common problem consisting of hypersonic flow past a slightly blunted conical forebody was undertaken to estimate the level of uncertainty in the computed results, and to assess the capabilities of current computational methods for predicting boundary-layer transition onset. Results of this study in terms of surface pressure and heat transfer comparisons, as well as comparisons of boundary-layer edge quantities and flow-field profiles are presented here. Sensitivities to grid and gas model are discussed. Finally, representative results are presented relating to the use of Computational Fluid Dynamics in the vehicle design and the integration/support of potential experiments.

Green, Michael J.↗
NASA NTRS1956

Investigation at supersonic and subsonic Mach numbers of auxiliary inlets supplying secondary air flow to ejector exhaust nozzles

The results indicated increases in auxiliary-inlet pressure recovery with increases in scoop height relative to the boundary-layer thickness. The pressure recovery increased at about the same rate as theoretically predicted for an inlet in a boundary layer having a one-seventh power profile, but was only about 0.68 to 0.75 of the theoretically obtainable values. Under some operating conditions, flow from the primary jet was exhausted through the auxiliary inlet. This phenomenon could be predicted from the ejector pumping characteristics.

Hearth, Donald P↗
NASA NTRS1994

Budget analysis of FIFE 1987 sonde data

Mean thermodynamic profiles are presented for the daytime convective boundary layer evolution for three groups of sunny days in late June and early July, August, and October using data from the First International Satellite Land Surface Climatology Project (ISLSCP) Field Experiment (FIFE) 1987 Kansas experiment. Budget models for the mixed layer evolution and the boundary layer rise are used to estimate the boundary layer top entrainment parameter. A value of A(sub R) = 0.44 +/- 0.21 is found for the mean ratio of the inversion level virtual heat flux to the surface virtual heat flux.

Betts, Alan K.↗
NASA NTRS2001

Flow-Tagging Velocimetry for Hypersonic Flows Using Fluorescence of Nitric Oxide

We investigate a new type of flow-tagging velocimetry technique for hypersonic flows. The technique involves exciting a thin line of nitric oxide molecules with a laser beam and then, after some delay, acquiring an image of the displaced line. One component of velocity is determined from the time of flight. This method is applied to measure the velocity profile in a Mach 8.5 laminar, hypersonic boundary layer in the Australian National Universities T2 free-piston shock tunnel. The velocity is measured with an uncertainty of approximately 2%. Comparison with a CFD simulation of the flow shows reasonable agreement.

Danehy, P. M.↗
NASA NTRS2002

Airborne Lidar Measurements of Aerosol Optical Properties During SAFARI-2000

The Cloud Physics Lidar (CPL) operated onboard the NASA ER-2 high altitude aircraft during the SAFARI-2000 field campaign. The CPL provided high spatial resolution measurements of aerosol optical properties at both 1064 nm and 532 nm. We present here results of planetary boundary layer (PBL) aerosol optical depth analysis and profiles of aerosol extinction. Variation of optical depth and extinction are examined as a function of regional location. The wide-scale aerosol mapping obtained by the CPL is a unique data set that will aid in future studies of aerosol transport. Comparisons between the airborne CPL and ground-based MicroPulse Lidar Network (MPL-Net) sites are shown to have good agreement.

McGill, M. J.↗
NASA NTRS2008

Demonstration of Aerosol Property Profiling by Multi-wavelength Lidar Under Varying Relative Humidity Conditions

The feasibility of using a multi-wavelength Mie-Raman lidar based on a tripled Nd:YAG laser for profiling aerosol physical parameters in the planetary boundary layer (PBL) under varying conditions of relative humidity (RH) is studied. The lidar quantifies three aerosol backscattering and two extinction coefficients and from these optical data the particle parameters such as concentration, size and complex refractive index are retrieved through inversion with regularization. The column-integrated, lidar-derived parameters are compared with results from the AERONET sun photometer. The lidar and sun photometer agree well in the characterization of the fine mode parameters, however the lidar shows less sensitivity to coarse mode. The lidar results reveal a strong dependence of particle properties on RH. The height regions with enhanced RH are characterized by an increase of backscattering and extinction coefficient and a decrease in the Angstrom exponent coinciding with an increase in the particle size. We present data selection techniques useful for selecting cases that can support the calculation of hygroscopic growth parameters using lidar. Hygroscopic growth factors calculated using these techniques agree with expectations despite the lack of co-located radiosonde data. Despite this limitation, the results demonstrate the potential of multi-wavelength Raman lidar technique for study of aerosol humidification process.

Whiteman, D.N.↗
NASA NTRS2003

Flow-Tagging Velocimetry for Hypersonic Flows Using Fluorescence of Nitric Oxide

We demonstrate a new variation of molecular-tagging velocimetry for hypersonic flows based on laser-induced fluorescence. A thin line of nitric-oxide molecules is excited with a laser beam and then, after a time delay, a fluorescence image of the displaced line is acquired. One component of velocity is determined from the time of flight. This method is applied to measure the velocity profile in a Mach 8.5 laminar, hypersonic boundary layer in the Australian National University s T2 free-piston shock tunnel. The single-shot velocity measurement uncertainty in the freestream was found to be 3.5%, based on 90% confidence. The method is also demonstrated in the separated flow region forward of a blunt fin attached to a flat plate in a Mach 7.4 flow produced by the Australian National University s T3 free-piston shock tunnel. The measurement uncertainty in the blunt fin experiment is approximately 30%, owing mainly to low fluorescence intensities, which could be improved significantly in future experiments. This velocimetry method is applicable to very high-speed flows that have low collisional quenching of the fluorescing species. It is particularly convenient in facilities where planar laser-induced fluorescence is already being performed.

Danehy, Paul M.↗
NASA NTRS2015

Application of FLEET Velocimetry in the NASA Langley 0.3-meter Transonic Cryogenic Tunnel

Femtosecond laser electronic excitation and tagging (FLEET) velocimetry is demonstrated in a large-scale transonic cryogenic wind tunnel. Test conditions include total pressures, total temperatures, and Mach numbers ranging from 15 to 58 psia, 200 to 295 K, and 0.2 to 0.75, respectively. Freestream velocity measurements exhibit accuracies within 1 percent and precisions better than 1 m/s. The measured velocities adhere closely to isentropic flow theory over the domain of temperatures and pressures that were tested. Additional velocity measurements are made within the tunnel boundary layer; virtual trajectories traced out by the FLEET signal are indicative of the characteristic turbulent behavior in this region of the flow, where the unsteadiness increases demonstrably as the wall is approached. Mean velocities taken within the boundary layer are in agreement with theoretical velocity profiles, though the fluctuating velocities exhibit a greater deviation from theoretical predictions.

Burns, Ross A.↗
NASA NTRS1987

A model of the wall boundary layer for ducted propellers

The objective of the present study is to include a representation of a wall boundary layer in an existing finite element model of the propeller in the wind tunnel environment. The major consideration is that the new formulation should introduce only modest alterations in the numerical model and should still be capable of producing economical predictions of the radiated acoustic field. This is accomplished by using a stepped approximation in which the velocity profile is piecewise constant in layers. In the limit of infinitesimally thin layers, the velocity profile of the stepped approximation coincides with that of the continuous profile. The approach described here could also be useful in modeling the boundary layer in other duct applications, particularly in the computation of the radiated acoustic field for sources contained in a duct.

Eversman, Walter↗
NASA NTRS1990

Thermal advection and stratification effects on surface winds and the low level meridional mass transport

Statistical tests are performed on the Seasat scatterometer observations to examine if and to what degree thermal advection and stratification effects manifest themselves in these remotely sensed measurements of mean wind and wind stress over the ocean. On the basis of a two layer baroclinic boundary layer model which is presented, it is shown that the thermal advection and stratification of the entire boundary layer as well as the geostrophic forcing influence the modeled near surface wind and wind stress profiles. Evidence of diurnal variation in the stratification under barotropic conditions is found in the data, with the daytime marine boundary layer being more convective than its nighttime counterpart. The temporal and spacial sampling pattern of the satellite makes it impossible to recover the full diurnal cycle, however. The observed effects of the thermal advection are shown to be statistically significant during the day (and presumed more convective) hours, causing a systematic increase in the poleward transport of mass and heat. The statistical results are in a qualitative agreement with the model simulations and cannot be reproduced in randomized control tests.

Levy, Gad↗
NASA NTRS1973

Modeling of turbulent transport in the surface layer

The turbulence equations as written by Donaldson using the method of invariant modeling have been applied to the following limiting cases of the surface or constant flux layer of the planetary boundary layer: (1) Neutrally stable; (2) stable (above influence of surface roughness); (3) nearly neutrally stable; and (4) very unstable (free convection). For the neutrally stable case, the equations are shown to admit as a solution the familiar logarithmic profile. By use of this result, boundary conditions suitable for the surface layer are defined and are simple to apply to rough surfaces.

Smith, G. L.↗
DOE OSTI2020

Simulation of Continental Shallow Cumulus Populations Using an Observation-Constrained Cloud-System Resolving Model

Continental shallow cumulus (ShCu) clouds observed on 30 August 2016 during the Holistic Interactions of Shallow Clouds, Aerosols, and Land-Ecosystems (HI-SCALE) field campaign are simulated by using an observation-constrained cloud-system resolving model. On this day, ShCu forms over Oklahoma and southern Kansas and some of these clouds transition to deeper, precipitating convection during the afternoon. We apply a four-dimensional ensemble-variational (4DEnVar) hybrid technique in the Community Gridpoint Statistical Interpolation (GSI) system to assimilate operational data sets and unique boundary layer measurements including a Raman lidar, radar wind profilers, radiosondes, and surface stations collected by the U.S. Department of Energy's (DOE) Atmospheric Radiation Measurement (ARM) Southern Great Plains (SGP) atmospheric observatory into the Weather Research and Forecasting (WRF) model to ascertain how improved environmental conditions can influence forecasts of ShCu populations and the transition to deeper convection. Independent observations from aircraft, satellite, as well as ARM's remote sensors are used to evaluate model performance in different aspects. Several model experiments are conducted to identify the impact of data assimilation (DA) on the prediction of clouds evolution. The analyses indicate that ShCu populations are more accurately reproduced after DA in terms of cloud initiation time and cloud base height, which can be attributed to an improved representation of the ambient meteorological conditions and the convective boundary layer. Extending the assimilation to 18 UTC (local noon) also improved the simulation of shallow-to-deep transitions of convective clouds.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1985

Preliminary study of inphase gusts and moment force wind loads over the first 150 meters at KSC, Florida

A mathematical/statistical analysis of inphase gusts and wind velocity moment forces over the first 150 m at the Kennedy Space Center (KSC) is presented. The wind velocity profile data were acquired at the KSC 150 m ground wind tower. The results show that planetary boundary layer (PBL) winds can sustain near peak speeds for periods up to 60 sec and longer. This is proven from calculating the autocorrelation functions of moment forces for several 10 min cases of wind profile data. The results show that lower atmospheric planetary boundary layer winds have periodic variations for long periods of time. This flow characteristic is valuable as aerospace vehicle engineering and design criteria where wind loading must be determined.

Kaufman, J. W.↗
DOE OSTI2022

On the enhancement of boundary layer skin friction by turbulence: an angular momentum approach

Turbulence enhances the wall shear stress in boundary layers, significantly increasing the drag on streamlined bodies. Other flow features such as free stream pressure gradients and streamwise boundary layer growth also strongly influence the local skin friction. In this paper, an angular momentum integral (AMI) equation is introduced to quantify these effects by representing them as torques that alter the shape of the mean velocity profile. This approach uniquely isolates the skin friction of a Blasius boundary layer in a single term that depends only on the Reynolds number most relevant to the flow's engineering context, so that other torques are interpreted as augmentations relative to the laminar case having the same Reynolds number. The AMI equation for external flows shares this key property with the so-called FIK relation for internal flows (Fukagata et al. , Phys. Fluids , vol. 14, 2002, pp. L73–L76). Without a geometrically imposed boundary layer thickness, the length scale in the Reynolds number for the AMI equation may be chosen freely. After a brief demonstration using Falkner–Skan boundary layers, the AMI equation is applied as a diagnostic tool on four transitional and turbulent boundary layer direct numerical simulation datasets. Regions of negative wall-normal velocity are shown to play a key role in limiting the peak skin friction during the late stages of transition, and the relative strengths of terms in the AMI equation become independent of the transition mechanism a very short distance into the fully turbulent regime. The AMI equation establishes an intuitive, extensible framework for interpreting the impact of turbulence and flow control strategies on boundary layer skin friction.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1980

Investigation of blown boundary layers with an improved wall jet system

Measurements were made in a two dimensional incompressible wall jet submerged under a thick upstream boundary layer with a zero pressure gradient and an adverse pressure gradient. The measurements included mean velocity and Reynolds stresses profiles, skin friction, and turbulence spectra. The measurements were confined to practical ratios (less than 2) of the jet velocity to the free stream velocity. The wall jet used in the experiments had an asymmetric velocity profile with a relatively higher concentration of momentum away from the wall. An asymmetric jet velocity profile has distinct advantages over a uniform jet velocity profile, especially in the control of separation. Predictions were made using Irwin's (1974) method for blown boundary layers. The predictions clearly show the difference in flow development between an asymmetric jet velocity profile and a uniform jet velocity profile.

Saripalli, K. R.↗
NASA NTRS1994

High-lift flow-physics flight experiments on a subsonic civil transport aircraft (B737-100)

As part of the subsonic transport high-lift program, flight experiments are being conducted using NASA Langley's B737-100 to measure the flow characteristics of the multi-element high-lift system at full-scale high-Reynolds-number conditions. The instrumentation consists of hot-film anemometers to measure boundary-layer states, an infra-red camera to detect transition from laminar to turbulent flow, Preston tubes to measure wall shear stress, boundary-layer rakes to measure off-surface velocity profiles, and pressure orifices to measure surface pressure distributions. The initial phase of this research project was recently concluded with two flights on July 14. This phase consisted of a total of twenty flights over a period of about ten weeks. In the coming months the data obtained in this initial set of flight experiments will be analyzed and the results will be used to finalize the instrumentation layout for the next set of flight experiments scheduled for Winter and Spring of 1995. The main goal of these upcoming flights will be: (1) to measure more detailed surface pressure distributions across the wing for a range of flight conditions and flap settings; (2) to visualize the surface flows across the multi-element wing at high-lift conditions using fluorescent mini tufts; and (3) to measure in more detail the changes in boundary-layer state on the various flap elements as a result of changes in flight condition and flap deflection. These flight measured results are being correlated with experimental data measured in ground-based facilities as well as with computational data calculated with methods based on the Navier-Stokes equations or a reduced set of these equations. Also these results provide insight into the extent of laminar flow that exists on actual multi-element lifting surfaces at full-scale high-life conditions. Preliminary results indicate that depending on the deflection angle, the slat and flap elements have significant regions of laminar flow over a wide range of angles of attack. Boundary-layer transition mechanisms that were observed include attachment-line contamination on the slat and inflectional instability on the slat and fore flap. Also, the results agree fairly well with the predictions reported in a paper presented at last year's AIAA Fluid Dynamics Conference. The fact that extended regions of laminar flow are shown to exist on the various elements of the high-lift system raises the question what the effect is of loss of laminar flow as a result of insect contamiantion, rain or ice accumulation on high-life performance.

Vandam, Cornelis P.↗