Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AIRPLANE - PERFORMANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 685 records · Page 38
All sourcesNASA NTRSDOE OSTI
NASA NTRS1954

Hydrodynamic Investigation of the the Take-Off Characteristics of a 1/10-Scale Dynamic Model of the Convair XF2Y-1 Airplane

An investigation was made of the take-off characteristics of a 1/10-scale dynamic model of the Convair XF2Y-1 airplane. This airplane is a water-based, jet-propelled, delta-wing fighter incorporating a hydro-ski landing gear. Tests were made with the original configuration, with the beaching wheels removed, and with the wheels installed and fairings added in front of the wheels. Each configuration was tested at weight and balance conditions simulating 17,000 pounds gross weight with the moment due t o 7,600 pounds of thrust, 17,300 pounds gross weight with a 9,500-pound thrust condition, and 23,000 pounds gross weight with a 9,300-pound thrust condition. Constant-speed runs were made at various elevon settings and vertical ski-strut positions; and trim, rise, and resistance were measured. Accelerated runs were made with controlled elevons and scale shock struts which could be extended as desired, and the longitudinal stability and spray characteristics were observed and photographed.

McBridge, Ellis E.↗
NASA NTRS1954

A Transonic Wind-Tunnel Investigation of the Longitudinal Aerodynamic Characteristics of a Model of the Lockheed XF-104 Airplane

The transonic longitudinal aerodynamic characteristics of a 0.0858-scale model of the Lockheed XF-104 airplane have been obtained from tests at the Langley 16-foot transonic tunnel. The results of the investigation provide some general information applicable to the transonic properties of thin, low-aspect-ratio, unswept wing configurations utilizing a high horizontal tail . The model employs a horizontal tail mounted at the top of the vertical tail and a wing with an aspect ratio of 2.5, a taper ratio of 0.385, and 3.4-percent-thick airfoil sections. The lift, drag, and static longitudinal pitching moment were measured at Mach numbers from 0.80 t o 1.09 and angles of attack from -2.5 deg to 22.5 deg. Some of the dynamic longitudinal stability properties of the airplane have been predicted from the test results. In addition, some visual flow studies on the wing surfaces obtained at Mach numbers of 0.80 and 1.00 are included. Results of the investigation show that the transonic rise in drag coefficient at zero lift is about 0.030. At high angles of attack, the model becomes longitudinally unstable at Mach numbers from 0.80 t o 0.90, whereas a reduction in static stability is experienced when very high angles of attack are reached at Mach numbers above 0.90. Longitudinal dynamic stability calculations show that the longitudinal control is good at angles of attack below the unstable break in the static pitching-moment curves, but a typical corrective control applied after the occurrence of neutral stability has little effect in averting pitch-up.

Hieser, Gerald↗
NASA NTRS1953

Low-Speed Longitudinal Stability Characteristics of a 1/6-Scale Model of the Republic XF-84H Airplane with the Propeller Operating

A low-speed investigation was made of a 1/6-scale model of the Republic XF-84H airplane. The model had a single tractor propeller and a 40deg swept wing of aspect ratio 3.45. This investigation was undertaken to provide information on the effects of propeller operation on longitudinal stability characteristics for the XF -84H airplane and to provide an indication of slipstream effects that might be encountered on similar swept-wing configurations. Effects of propeller operation were generally destabilizing for all conditions investigated; however, the over-all stability characteristics with power on were greatly dependent on the power-off characteristics. With flaps and slats retracted, longitudinal instability was present at moderate angles of attack both with the propeller off and with power on. The longitudinal stability with flaps and slats deflected, which was satisfactory without power, was decreased by propeller operation, but no marked pitch-up tendency was indicated. Significant improvement in the power-on stability with flaps retracted was achieved by use of either a wing fence at 75 percent semispan, a leading-edge chord-extension from 65 to 94 percent semispan, or a raised horizontal tail located 65 percent semispan above the thrust line.

Sleeman, William C.↗
NASA NTRS1953

Drag and Longitudinal Trim at Low Lift of the North American YF-100A Airplane at Mach Numbers from 0.76 to 1.77 as Determined from the Flight Test of a 0.11-Scale Rocket Model

Drag and longitudinal trim at low lift of the North American YF-100A airplane at Mach numbers from 0.76 to 1.77 as determined from the flight test of a 0.11-scale rocket model are presented herein. Also included are some longitudinal stability and some qualitative pitch-damping data. The subsonic external-drag-coefficient level was about 0.012, and the supersonic level was about 0.043. The drag rise occurred at a Mach number of 0.95. The longitudinal trim change at low lift consisted basically of a mild nose-up tendency at a Mach number of 0.90. An indication of wing flutter was present at Mach numbers from 0.95 to 1.11. However, the full-scale airplane wing has approximately twice the scaled first-bending frequency as the model tested and, hence, will probably be free of this type of flutter. The aerodynamic-center location was 71 percent behind the leading edge of the mean aerodynamic chord at a Mach number of 1.03 and 62 percent at a Mach number of 1.74. Qualitative measurement of damping in pitch indicates that at low lift coefficients damping will be low at a Mach number of 1.03.

Blanchard, Willard S.↗
NASA NTRS1951

Supplementary Free-Spinning-Tunnel Investigation of a 1/30-Scale Model of the Grumman XF10F-1 Airplane in the Swept-Wing Configuration with Slats Extended

A supplementary investigation has been conducted in the Langley 20-foot free-spinning tunnel of a 1/30 -scale model of the Grumman XFlOF-1 airplane to determine what effect full-span slats would have on the spin-recovery characteristics of the swept-wing version of the XFlOF-1 airplane, which had previously been indicated as possessing undesirable spin-recovery characteristics without slats. The effects of extended nose-wheel doors and of fairing the air-duct inlets were also determined. The results indicated that, with slats fully extended, satisfactory recovery could be obtained by rudder reversal provided it was accompanied by movement of the trimmer ailerons to full with the spin (only up-going spoiler operative), Extension of the nose-wheel doors or fairing of the air-duct inlets did not improve the recovery characteristics.

Berman, Theodore↗
NASA NTRS1951

Investigation to Determine the Effectiveness of a Split-Aileron Type Emergency Spin-Recovery Device for the Northrop XF-89 Airplane

The present paper presents the results of a brief investigation made to determine the effectiveness of a proposed emergency spin-recovery device to be used during demonstration spins of the Northrop XF -89 airplane. The proposed device makes use of split-type ailerons deflected +/-60deg on the outboard wing (left wing in a right spin). Tests made on a model which represented the airplane to a scale of 7 indicated that, if an uncontrollable spin is obtained in the design gross--weight loading, the device is not sufficiently effective to insure recovery,

Neihouse, A. I.↗
NASA NTRS1947

Altitude Cooling Investigation of the R-2800-21 Engine in the P-47G Airplane. IV - Engine Cooling-Air Pressure Distribution

A study of the data obtained in a flight investigation of an R-2800-21 engine in a P-47G airplane was made to determine the effect of the flight variables on the engine cooling-air pressure distribution. The investigation consisted of level flights at altitudes from 5000 to 35,000 feet for the normal range of engine and airplane operation. The data showed that the average engine front pressures ranged from 0.73 to 0.82 of the impact pressure (velocity head). The average engine rear pressures ranged from 0.50 to 0.55 of the impact pressure for closed cowl flaps and from 0.10 to 0.20 for full-open cowl flaps. In general, the highest front pressures were obtained at the bottom of the engine. The rear pressures for the rear-row cylinders were .lower and the pressure drops correspondingly higher than for the front-row cylinders. The rear-pressure distribution was materially affected by cowl-flap position in that the differences between the rear pressures of the front-row and rear-row cylinders markedly increased as the cowl flaps were opened. For full-open cowl flaps, the pressure drops across the rear-row cylinders were in the order of 0.2 of the impact pressure greater than across the front-row cylinders. Propeller speed and altitude had little effect on the -coolingair pressure distribution, Increase in angle of inclination of the thrust axis decreased the front ?pressures for the cylinders at the top of the engine and increased them for the cylinders at the bottom of the engine. As more auxiliary air was taken from the engine cowling, the front pressures and, to a lesser extent, the rear pressures for the cylinders at the bottom of the engine decreased. No correlation existed between the cooling-air pressure-drop distribution and the cylinder-temperature distribution.

Kaufman, Samuel J.↗
NASA NTRS1949

The Effects of Horizontal-Tail Location and Wing Modifications on the High-Speed Stability and Control Characteristics of a 01.17-Scale Model of the McDonnell XF2H-1 Airplane (TED No, NACA DE336)

An additional series of high-speed wind-tunnel tests of a modified 0.17-scale model of the McDonnell XF2H-1 airplane was conducted to evaluate the effects of a reduction in the thickness-to-chord ratios of the tail planes, the displacement of the horizontal tail relative to the vertical tail, and the extension of the trailing edge of the wing. Two tail-intersection fairings designed to improve the flow at the tail were also tested. The pitching-moment characteristics of the model were improved slightly by the use of the thinner tail sections. Rearward or rearward and downward displacements of the horizontal tail increased the critical Mach number at the tail intersection from 0.725 to a maximum of 0.80, but caused an excessive change in pitching-moment coefficient at the higher Mach numbers. Extending the trailing edge of the wing did not improve the static longitudinal-stability characteristics, but increased the pitching-down tendency between 0.725 and 0.825 Mach numbers prior to the pitching-up tendency. The extended wing did, however, increase the Mach numbers at which these tendencies occurred. The increase in the Mach numbers of divergence and the tuft studies indicate a probable increase in the buffet limit of the prototype airplane. No perceptible improvement of flow at the tail intersection was observed with the two fairings tested on the forward tail configuration.

Emerson, Horace F.↗
NASA NTRS1949

Ditching Investigation of a 1/18-Scale Model of the North American B-45 Airplane

An investigation of a 1/18-scale dynamically similar model of the North American B-45 airplane was made to observe the ditching behavior and determine the proper landing technique to be used in an emergency water landing. Various conditions of damage were simulated to determine the behavior which probably would occur in a full-scale ditching. The behavior of the model was determined from high-speed motion-picture records, time-history acceleration records, and visual observations. It was concluded that the airplane should be ditched at the maximum nose-high attitude with the landing flaps full down for minimum landing speed. During the ditching, the nose-wheel and bomb-bay doors probably will be torn away and the rear of the fuselage flooded. A violent dive will very likely occur. Longitudinal decelerations of approximately 5g and vertical accelerations of approximately -6g (including gravity) will be experienced near the pilots' compartment. Ditching braces installed in the bomb bay will tend to improve the behavior slightly but will be torn away along with the bomb-bay doors. A hydroflap installed ahead of the nose-wheel doors will eliminate the dive and failure of the nose-wheel doors, and substantially reduce the motions and accelerations.

Fisher, Lloyd J.↗
NASA NTRS1949

Free-Spinning-Tunnel Investigation of a 1/20-Scale Model of the McDonnell XF2H-1 Airplane

A spin-recovery investigation has been conducted in the Langley 20-foot free-spinning tunnel on a 20-scale model modified to represent the McDonnell XF2H-1 airplane. The project included tests both with tip tanks installed and with the tanks removed. The results indicated that the recovery characteristics of the airplane would be satisfactory for all loadings by normal recovery technique (full reversal of the rudder, followed 1/2 turn later by movement of the elevator down). The rudder pedal and the elevator stick forces likely to be encountered in a spin should be within the capabilities of the pilot.

Berman, Theodore↗
NASA NTRS1954

Investigation of the Hydrodynamic Characteristics of the Panto-Base Chase C-123 Airplane

An investigation of a 1/14-scale dynamically similar model of a panto-base version of the Chase C-123 airplane was conducted to evaluate the hydrodynamic characteristics of the airplane. The resistance, longitudinal stability, and spray patterns during take-off and general behavior in calm- and rough-water landings were determined. Brief calm-water tests were made to compare the initial vertical impact accelerations of the model with and without hydro-skis. Take-off stability was satisfactory for calm-water operation. A ratio of gross load to maximum resistance of 3,6 was obtained. Heavy spray reached the propellers only during ski emergence. The landing behavior in calm water and in waves 3 feet by 150 feet (full scale) was satisfactory for a normal range of trim angles. Initial impacts in calmwater landings resulted in vertical accelerations of about 2 1/2 with the hydro-skis installed and about 4g with the hydro-skis removed,

Thompson, William C.↗
NASA NTRS2004

Solar-Powered Airplane with Cameras and WLAN

An experimental airborne remote sensing system includes a remotely controlled, lightweight, solar-powered airplane (see figure) that carries two digital-output electronic cameras and communicates with a nearby ground control and monitoring station via a wireless local-area network (WLAN). The speed of the airplane -- typically <50 km/h -- is low enough to enable loitering over farm fields, disaster scenes, or other areas of interest to collect high-resolution digital imagery that could be delivered to end users (e.g., farm managers or disaster-relief coordinators) in nearly real time.

Higgins, Robert G.↗
NASA NTRS1940

Tests of the XP-46 Airplane in the N.A.C.A. Full-Scale Wind Tunnel

An investigation has been conducted on a full-scale model of the proposed XP-46 airplane in the N. A. C. A. full-scale wind tunnel pursuant to the request of the Amy Air Corps, Materiel Division. The primary purpose of the investigation was to determine the optimum arrangement of the various component parts to obtain the maximum high speed and to provide adequate engine cooling. Additional tests included a determination of the stalling characteristics and the effectiveness of ailerons and elevators. The profile drag of the wing was ascertained by the momentum method; the location of the transition point on the wing and the critical compressibility velocities of the various airplane components were determined from surface pressure surveys.

Nickle, F. R.↗
NASA NTRS2014

Assessing V and V Processes for Automation with Respect to Vulnerabilities to Loss of Airplane State Awareness

Automation has contributed substantially to the sustained improvement of aviation safety by minimizing the physical workload of the pilot and increasing operational efficiency. Nevertheless, in complex and highly automated aircraft, automation also has unintended consequences. As systems become more complex and the authority and autonomy (A&A) of the automation increases, human operators become relegated to the role of a system supervisor or administrator, a passive role not conducive to maintaining engagement and airplane state awareness (ASA). The consequence is that flight crews can often come to over rely on the automation, become less engaged in the human-machine interaction, and lose awareness of the automation mode under which the aircraft is operating. Likewise, the complexity of the system and automation modes may lead to poor understanding of the interaction between a mode of automation and a particular system configuration or phase of flight. These and other examples of mode confusion often lead to mismanaging the aircraftâ€"TM"s energy state or the aircraft deviating from the intended flight path. This report examines methods for assessing whether, and how, operational constructs properly assign authority and autonomy in a safe and coordinated manner, with particular emphasis on assuring adequate airplane state awareness by the flight crew and air traffic controllers in off-nominal and/or complex situations.

Whitlow, Stephen↗
NASA NTRS1945

High-Speed Wind-Tunnel Tests of a 0.3-Scale Model of the P-47D Airplane

Presented in this report are the results of high-speed wind-tunnel tests of a 0.3-scale model of the P-47D airplane. Included are the aerodynamic characteristics of the model, pressure distributions on the wing and horizontal tail, elevator hinge moments, and tuft photographs showing the flow over the wing and horizontal tail. The results indicate that, at level-flight lift coefficients, the P-47D airplane will not exhibit a diving tendency below a Mach number of 0.78 at an altitude of 20,000 feet or below a Mach number of 0.72 at an altitude of 40,000 feet. The Mach number at which the lift, drag, and pitching-moment coefficients diverged rapidly from the low speed values is about C.15 higher than the critical Mach number. This is an unusually large margin.

William T Hamilton↗
NASA NTRS1942

Control-Surface Instability on High-Speed Airplanes

Tests of several modern airplanes indicate that control surfaces with a high degree of aerodynamic balance are likely to possess characteristics which make them unsatisfactory or dangerous in high-speed flight. Dive tests made in the spring of 1940 at the NACA on a naval fighter-type airplane illustrate one form of instability that may be encountered. During a dive at an indicated airspeed of 365 miles per hour, the ailerons suddenly overbalanced. The efforts of the pilot to bring the ailerons back to neutral resulted in a violent oscillation of the control stick from side to side. Fortunately, the force required to return the ailerons to neutral was within the pilot's capabilities. A time history of the maneuver is given in figure1 and typical frames from motion pictures of the cockpit and of the wing, taken during the maneuver, are given in figure 2. In the illustrated case, the occurrence of aerodynamic overbalance was attributed to a slight bulge, approximately 1/16 inch thick, on the lower surface of the leading edges of the ailerons, caused by the installation of additional mass balance ahead of the hinge line. A drawing showing the shape of the bulge is given in figure 3. After this slight protuberance had been eliminated, dives were successfully made at higher speeds.

Phillips, William H.↗
NASA NTRS1956

The Dynamic Response of a Large Airplane to Continuous Random Atmospheric Disturbances

The statistical approach to the gust-loads problem, which consists in considering flight th1ough turbulent air to be a stationary random process, is extended by including the effect of lateral variations of the instantaneous gust intensity on the aerodynamic forces and on the resultant motions and stresses of rigid and flexible airplanes. By means of some calculations of normal and rolling accelerations, as well as of the root bending moment, it is shown that these effects may be significant for large airplanes.

Aeroplane↗
NASA NTRS1942

Wind-Tunnel Tests of 1/6-Scale Model of Republic P-47C Airplane with External Wing Tank

In order to increase the range of the Republic P-47C airplane for ferrying purposes it has been proposed that the airplane be equipped with streamlined external wing tanks. This report presents the aerodynamic effect of such wing tanks as determined from tests of a l/6-scale model in the 7- by 10-foot tunnel of the Langley Memorial Aeronautical Laboratory.

Marvin J Schuldenfrei↗