Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yield strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fiber orientation and porosity in large-format extrusion process: The role of processing parameters

Controlling fiber orientation and porosity in short-fiber thermoplastic composites is important for enhancing mechanical, electrical and thermal properties in large-format additive manufacturing. This study employs a factorial design of experiments (DoE) to assess the effects of nozzle diameter (5.08 mm–10.16 mm), temperature (230–250 °C), and extruder screw speed (150–280 rpm) on flow rate, shear rate, porosity, fiber orientation, fiber length and tensile strength in 20 % carbon fiber-filled acrylonitrile butadiene styrene. ANOVA results show that screw speed significantly impacts flow rate, while nozzle diameter and temperature have lesser effects. Shear rate increases with smaller nozzles and higher speeds. Porosity decreases from 5.58 % with a 10.16 mm nozzle to 3.11 % with a 5.08 mm nozzle at 150 rpm due to increased shear rates, which induce shear thinning, reducing viscosity and facilitating gas escape. Larger nozzles (10.16 mm) produce larger, more heterogeneous pores, while smaller nozzles (5.08 mm) yield smaller, uniform pores. Beads produced with the 5.08 mm nozzle exhibit longer fiber lengths due to reduced residence time, lower shear stress, and better alignment. Fiber orientation improves with smaller nozzles due to higher shear rates but decreases with higher screw speeds (280 rpm) due to shorter residence times. The highest fiber alignment (A xx ∼ 0.65) and low porosity (∼3%) were achieved with a 5.08 mm nozzle at 150 rpm, while equivalent additive manufacturing-compression molding samples exhibited better tensile strength (∼93 MPa) under these conditions. In conclusion, these findings emphasize the importance of optimizing processing parameters to enhance fiber alignment and reduce porosity for improved mechanical performance.

Design of experiments↗
DOE OSTI2023

Controlling the Plastic Anisotropy of Magnesium Alloy by Tailoring the Grain Size and Yttrium Content

Hexagonal close-packed (HCP) magnesium alloys are widely used in automotive and aerospace industries due to their low density and high specific-strength. Their applicability is mainly restricted due to poor formability and pronounced plastic anisotropy. The formability is usually improved by altering the chemistry (adding rare-earth elements like Y) or modulating the microstructure (e.g., grain refinement). However, grain refinement alone cannot yield the desired ductility, and the scarcity of rare-earth elements also limits the extent to which the alloying strategy can be used. To overcome these issues, in this work, it is proposed that the formability of Mg alloys can be improved by combining the grain refinement and alloying approaches. To quantitively explore this possibility, a crystal-plasticity-based constitutive model, which is sensitive to both alloying concentration and grain sizes, is developed. To demonstrate, the model is applied to study the combined effect of Y content and grain size on the mechanical responses of Mg alloy. The calculations are used to build maps of plastic anisotropy measures, such as tension–compression asymmetry ratio and Lankford coefficients, for a wide range of Y content and grain sizes. From these maps, the grain size that would yield the desired performance of Mg alloy for a fixed Y content can be identified. This work provides an accelerated pathway to optimize both the microstructure and chemistry simultaneously to achieve formability and to reduce the dependence on alloying.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High spatial resolution neutron imaging of lithium-ion batteries: Correlating microstructure and lithium transport

Thick electrodes for lithium-ion batteries can increase the overall energy density, but increasing the electrode thickness introduces charge transport limitations. These limitations may be mitigated through proper electrode structuring. Here, high spatial resolution neutron imaging was used to understand the correlation between microstructure and lithium transport in lithium-ion anodes. Batteries with distinct graphite anode microstructures were produced and studied with high spatial resolution in operando neutron radiography to observe the effects of structure on transport. High spatial resolution neutron computed tomography was performed following in operando neutron radiography. X-ray computed tomography and scanning electron microscopy were used to observe the finer scale anode structure to complement neutron imaging. Solvent-free anodes containing a tightly-packed layered structure confined lithium movement close to the separator. This structure limited capacity, but supported better rate capability. Conversely, a more open pore structure in the wet cast anodes yielded higher capacity with reduced rate capability. Together, these results show that lithium distributions can be controlled by the macroscopic structure of the electrodes, the microstructural pore network, and the microscale active areas that support electrochemical reactions. Furthermore, multimodal imaging applying the complementary strengths of neutron and X-ray methods is shown as a tool for advancing battery design.

25 ENERGY STORAGE↗
DOE OSTI2026

Upcycling waste PET into functional multiblock copolymers through controlled macromolecular design

Poly(ethylene terephthalate) (PET) oligomers derived from glycolysis depolymerization were converted into multiblock copolymers through diisocyanate-mediated coupling with dihydroxy-terminated oligomers, enabling precise control over copolymer sequence distribution, connectivity, and mechanical performance. Here, we demonstrate that telechelic PET oligomers isolated directly from depolymerized consumer waste can serve as reactive building blocks for the formation of segmented multiblock copolymers, eliminating the need to revert to monomeric feedstocks. Dihydroxy-terminated PET oligomers (Mw ≈ 8 kg mol−1) were coupled with poly(ethylene oxide) (PEO, Mw ≈ 4 kg mol−1) to form PET-PEO multiblock copolymers with high molar mass (Mw ≈ 160 kg mol−1). We further show that the timing of end-capping reactions provides a key control parameter that governs the competition between chain extension and termination, thereby dictating the resulting multiblock architecture and molecular-weight evolution. Evaluation of their mechanical properties reveals that virgin PET exhibits high modulus (∼3 GPa) and strength (43 MPa) but limited ductility (<10% elongation). In contrast, PET–PEO multiblock copolymers retain comparable tensile strength (44 MPa), albeit while exhibiting dramatically enhanced ductility (>90% elongation), forming tougher materials with efficient stress transfer between the rigid PET domains and the flexible PEO segments. When incorporated into PET/PEO blends at low loadings, the multiblock copolymers serve as effective compatibilizers, yielding materials with an intermediate modulus (1.1–1.2 GPa) and improved elongation compared to uncompatibilized blends. Furthermore, the presence of PEO blocks increases water uptake and gas permeability relative to virgin PET, reflecting the tunability of molecular transport through the copolymeric blocks. To our knowledge, this represents the first report of PET–PEO multiblock copolymers derived from post-consumer PET for gas transport applications. These results demonstrate that multiblock copolymer formation from telechelic PET oligomers provides a versatile platform for tailoring the mechanical and transport behavior of polyester-based materials through controlled macromolecular design and establishes a generalizable strategy for transforming consumer plastic waste into functional segmented polymers without requiring complete depolymerization to monomers.

Watson-Sanders, Shelby [Department of Chemistry, U↗
DOE OSTI2021

Atomistic processes of surface-diffusion-induced abnormal softening in nanoscale metallic crystals

Abstract Ultrahigh surface-to-volume ratio in nanoscale materials, could dramatically facilitate mass transport, leading to surface-mediated diffusion similar to Coble-type creep in polycrystalline materials. Unfortunately, the Coble creep is just a conceptual model, and the associated physical mechanisms of mass transport have never been revealed at atomic scale. Akin to the ambiguities in Coble creep, atomic surface diffusion in nanoscale crystals remains largely unclear, especially when mediating yielding and plastic flow. Here, by using in situ nanomechanical testing under high-resolution transmission electron microscope, we find that the diffusion-assisted dislocation nucleation induces the transition from a normal to an inverse Hall-Petch-like relation of the strength-size dependence and the surface-creep leads to the abnormal softening in flow stress with the reduction in size of nanoscale silver, contrary to the classical “alternating dislocation starvation” behavior in nanoscale platinum. This work provides insights into the atomic-scale mechanisms of diffusion-mediated deformation in nanoscale materials, and impact on the design for ultrasmall-sized nanomechanical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Altered post-fracture systemic bone loss in a mouse model of osteocyte dysfunction

Femur fracture leads to loss of bone at uninjured skeletal sites, which may increase risk of subsequent fracture. Osteocytes, the most abundant bone cells, can directly resorb bone matrix and regulate osteoclast and osteoblast activity, but their role in systemic bone loss after fracture remains poorly understood. In this study we used a transgenic (TG+) mouse model that overexpresses human B-cell lymphoma 2 (BCL-2) in osteoblasts and osteocytes. This causes enhanced osteoblast proliferation, followed by disruption in lacunar-canalicular connectivity and massive osteocyte death by 10 wk of age. We hypothesized that reduced viable osteocyte density would decrease the magnitude of systemic bone loss after femur fracture, reduce perilacunar remodeling, and alter callus formation. Bone remodeling was assessed using serum biomarkers of bone formation and resorption at 5 d post-fracture. We used micro-computed tomography, high resolution x-ray microscopy, mechanical testing, and Raman spectroscopy to quantify the magnitude of systemic bone loss, as well as changes in osteocyte lacunar volume, bone strength, and bone composition 2 wk post-fracture. Fracture was associated with a reduction in circulating markers of bone resorption in non-transgenic (TG-) animals. TG+ mice exhibited high bone mass in the limbs, greater cortical elastic modulus and reduced post-yield displacement. After fracture, TG+ mice lost less trabecular bone than TG- mice, but conversely TG+ mice exhibited trends toward a lower yield point and reduced femoral cortical thickness after fracture, though these were not statistically significant. Lacunar density was greater in TG+ mice, but fracture did not alter lacunar volume in TG+ or TG- mice. These findings suggest that osteocytes potentially play a significant role in the post-traumatic systemic response to fracture, though the effects differ between trabecular and cortical bone.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Critical Literature Review of Quantitative Sustainability Assessment Methods for the Circular Economy

The circular economy (CE) has been proposed to be an operational framework for sustainable development that decouples economic growth from resource consumption. The CE ambition is to maximize the retention of value in products, materials, and resources in the economy over time with the help of CE strategies such as selling a service rather than a product, reusing and repairing products or their components, and recycling. The social, economic, and environmental performances of CE strategies need to be measured against their linear counterparts to avoid strategies that increase circularity but have other unintended externalities. However, there is currently no tool specifically designed to compare circular to linear systems and, thus, various methods from different fields have been applied. This session aims at reviewing, contrasting, and critiquing different methods that have been applied to assess the CE until now, along with an up to date state of the science in this field. Methods from the industrial ecology field have most often been applied to study the CE. However, the transition to CE involves both technological improvements as well as social changes. New business models such as collaborative consumption models (e.g., Uber or Airbnb) are examples of the new patterns of production and consumption of the CE, which may be difficult to analyze from a purely industrial ecology perspective. Methods from complexity science and humanities could therefore complement the industrial ecology perspective to extend the scope of the analysis. Such an approach could also answer a longstanding criticism of the CE which, in contrast with sustainability, solely focuses on the environment and the economy. Moreover, the hybridization of two or more existing methods can yield additional capabilities, which may enable the exploration of additional CE-related research questions. The 90 minutes session will have several presentations and conclude with a moderated, interactive panel discussion on how methods from different fields could be combined to harness their relative strengths.

circular economy↗
DOE OSTI2026

Selective Amnesia using Contrastive Subnet Erasure for Class Level Unlearning in Vision Models

We study concept-level forgetting in pretrained vision models: removing an entire semantic category so the system no longer recognizes that object in unseen images and contexts, rather than merely forgetting specific training examples. Prior work either applies blunt global projections or fine-tunes parameters, which can introduce collateral damage to unrelated features, add compute, and become unstable as forgetting strength increases. We introduce Contrastive Subnet Erasure (CSE), a training-free, encoder-centric edit that targets a compact set of channels most responsible for the class and attenuates them in a calibrated manner. The modification is algebraically folded into the subsequent layer, yielding no inference-time overhead and leaving task heads unchanged. To evaluate whether forgetting generalizes beyond the data used to specify the class, we introduce a cross dataset protocol in which the class is defined on a source dataset and performance is measured on a disjoint target dataset drawn from a different distribution with no shared images. This setup tests whether the model still fails to recognize the object when it looks different or appears in new scenes, and it helps avoid overfitting to patterns in the source dataset. Across CIFAR 10, CIFAR 100, and ImageNet under this protocol, CSE achieves stronger forgetting of the target class while better preserving non target utility than existing baselines in both single class and multi class settings. Overall, CSE provides a simple, stable, and deployment-ready mechanism for class-level unlearning in vision.

Kotevska, Olivera [ORNL] (ORCID:0000000316772243)↗
DOE OSTI2021

Adhesive Bonding of Copper Prepared by Laser-Interference near the Interference Structuring Limits

Adhesive bonding requires adequate surface preparation for ensuring an appropriate joint quality. The interest in adhesive joining has recently expanded to thermal systems having a large number of joints employed for manufacturing and assembly. This study presents surface topology of copper 110 produced by a laser-interference setup that would theoretically yield a periodicity of 1.7 μm, which is near the 1.6–2 μm structuring limit that was estimated based on thermal diffusion length scale for an 8 ns laser pulse. The results show that although the expected periodic interference structuring was not attained, the melt-induced texturing was affected by the laser-interference profile. Single-lap shear tests were performed with specimen surfaces prepared by traditional abrasion and laser-interference structuring methods. Several laser processing parameters, such as the laser spot size, density, number of pulses, and raster speed, were studied. Scanning electron microscope and profilometry measurements were used to characterize the processed surface microstructures. Web-like structures, which indicate widespread melting, were shown to be formed at different processing conditions. Based on the surface topologies investigated, two laser raster speeds were selected to make single-lap-joint specimens. Baseline joints were prepared by abrading joining specimens. The shear-lap strength and displacement at maximum load were shown to be higher by 16.8% and 43.8% for the laser-structured specimens than those of the baseline specimens, respectively. Moreover, the load-displacement curves indicated that the laser-structured joints were more ductile than those without laser-structuring. The increased ductility for the laser-structured joints was found to yield an increase in the energy absorbed during shear-lap testing of approximately of 80–90% over those measured for baseline joints. It is another indicator that laser-interference structuring enhanced the bonding performance of single-lap shear joints.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructure, compression properties, and oxidation behavior of Hf-25Ta-5Me alloys (Me is Mo, Nb, W, 0.5Mo + 0.5 W, Cr, or Zr)

Hf–Ta based alloys have recently been investigated as potential candidates for high-temperature structural applications. While most attentions have been given to the properties above ~1200 °C where the alloys are mainly single-phase BCC structures and have excellent oxidation performance due to formation of super-oxides, structural properties at lower temperatures are equally important for applications in which an alloy may experience a range of temperatures. In the present work, microstructure, phase composition, mechanical properties and oxidation behavior of six Hf-25Ta-5Me alloys (Me is Mo (HTM alloy), W (HTW), 0.5Mo + 0.5 W (HTMW), Cr (HTC) or Zr (HTZ), the compositions are in at.%) are reported at temperatures below the eutectoid transformation. The alloys were prepared by arc melting followed by hot isostatic pressing for 3 h at 1400 °C and 207 MPa. All the alloys display coarse grains of partially or fully transformed (by a eutectoid reaction) high-temperature BCC phase. The eutectoid regions consist of fine lamellae of Hf-rich HCP and Ta-rich BCC phases. The ternary alloys containing W or Cr also contained small amounts of a cubic Laves phase. At 25 °C, the HTW alloy was the strongest (yield stress σ y = 1966 MPa) but brittle and HTZ was the weakest (σ y = 1120 MPa) but ductile among the studied alloys. Other alloys showed intermediate behaviors. In general, the room temperature ductility of the alloys increased with decreasing σy. All alloys maintained high strength up to 800 °C, but displayed a noticeable strength decrease at 1000 °C. At 1000 °C, HTMW was the strongest alloy (σ y = 468 MPa) and HTC was the weakest alloy (σ y = 368 MPa). All alloys had excellent deformability at 1000 °C. Oxidation behavior of the alloys was studied at 800 °C and 1000 °C and compared with that of Hf–27Ta binary alloy. Although the ternary additions improved oxidation resistance, overall oxidation performance of the studied alloys at 800 °C and 1000 °C was poor.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Significantly Promoting the Thermal Conductivity and Machinability of Negative Thermal Expansion Alloy via In Situ Precipitation of Copper Networks

Rapid advancements in electronic devices yield an urgent demand for high-performance electronic packaging materials with high thermal conductivity, low thermal expansion, and great mechanical properties. However, it is a great challenge for current design philosophies to fulfill all the requirements simultaneously. Here, an effective strategy is proposed for significantly promoting the thermal conductivity and machinability of negative thermal expansion alloy (Zr,Nb)Fe 2 through eutectic precipitation of copper networks. The eutectic dual-phase alloy exhibits an isotropic chips-matched thermal expansion coefficient and a thermal conductivity enhancement exceeding 200% compared with (Zr,Nb)Fe 2 , along with an ultimate compressive strength of 550 MPa. The addition of copper reorganizes the composition of (Zr,Nb)Fe 2 , which smooths the magnetic transition and shifts it toward higher temperature, resulting in linear low thermal expansion in a wide temperature range. The highly fine eutectic copper lamellae construct high thermal conductivity networks within (Zr,Nb)Fe 2 , serving as highways for heat transfer electrons and phonons. The in situ forming of eutectic copper lamellae also facilitates the mechanical properties by enhancing interfacial bonding and bearing additional stress after yielding of (Zr,Nb)Fe 2 . This work provides a novel strategy for promoting thermal conductivity and mechanical properties of negative thermal expansion alloys via eutectic precipitation of copper networks.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermodynamic Analysis of Nano-Electrospray Induced Gas Jets

Nano-electrospray (nES) produces a plume of charged liquid droplets which have drag interactions with the surrounding gas after they are emitted from a source capillary. The resulting induced gas flow has often been considered unimportant, but we have demonstrated that a gas microjet of significant velocity up to 10s of m/s can be produced. In this work we present a thermodynamic framework that enables analysis of gas jet generation from electrosprays and introduce the important metrics for such analysis, effectiveness (a measure of momentum transfer from the electrosprayed aerosol to gas) and efficiency (a measure of energy conversion from electrical energy generating the electrospray to gas kinetic energy). This analytical framework is applicable to any two-phase flows consisting of discrete conservative-force-driven particles which exchange momentum with an inert, otherwise quiescent fluid medium to yield a co-flowing two-phase jet. Here, we apply this framework to sprays of water from nano-electrospray emitters to demonstrate that increasing the applied electrical potential difference, increasing liquid mass flowrate, and decreasing droplet size all can increase electrospray induced gas jet strength, but only the latter two do so while also increasing the momentum transfer effectiveness and energy conversion efficiency.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Dynamical friction in self-interacting ultralight dark matter

Here, we explore how dynamical friction in an ultralight dark matter (ULDM) background is affected by dark matter self-interactions. We calculate the force of dynamical friction on a point mass moving through a uniform ULDM background with self-interactions, finding that the force of dynamical friction vanishes for sufficiently strong repulsive self-interactions. Using the pseudospectral solver ultraDark.jl, we show with simulations that reasonable values of the ULDM self-interaction strength and particle mass cause $\mathcal{O}$(1) differences in the acceleration of an object like a supermassive black hole (SMBH) traveling near the center of a soliton, relative to the case with no self-interactions. For example, repulsive self-interactions with λ=10 -90 yield a deceleration due to dynamical friction ≈ 70% smaller than a model with no self-interactions. We discuss the observational implications of our results for SMBHs near soliton centers and for massive satellite galaxies falling into ultralight axion halos and show that outcomes are dependent on whether a self-interaction is present or not.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Additive manufacturing of mullite ceramic by digital light processing

Mullite material was successfully additively manufactured using digital light processing (DLP). The printed geometry involves a one-step process of pyrolysis, de-binding, and sintering under a plain atmosphere to achieve an average of 76 % ceramic yield and linear shrinkage of 12 %. Furthermore, the thermal profile was carefully controlled to obtain consistent phases in which the XRD shows a mullite phase. Here, in addition, the Weibull analysis was conducted on the sintered flexural specimens, showing a Weibull modulus (m) of 13.05 with a characteristic strength (σ 0 ) of 94.96 MPa. Synchrotron microtomography was performed on the sintered specimens, which showed two distinct porosity distributions (small and large). Large porosity (non-spherical elongated) is the primary cause of decreased material strength, while small porosity (spherical) is the sintering product. The measured thermal conductivity of the specimens was in the range of 2.7–3.1 W/m∙k and decreased with an increase in temperature. Lastly, large-scale prototypes were printed concurrently with a fine resolution of 25 μm without any compromise on the predetermined design and structure.

Additive manufacturing↗
DOE OSTI2025

Thermal and mechanical performance of gypsum composites containing fly ash cenosphere encapsulated phase change materials

Utilizing phase change materials (PCMs) within construction materials improves the thermal energy storage capabilities in the built environment. Notably, integrating PCMs into drywalls presents a promising avenue to reduce building energy use. However, incorporating PCMs into drywalls poses challenges, particularly reduced mechanical properties and workability limitations as it can adversely affect the hardening and cohesiveness of gypsum composites. To address these challenges, this study explores a novel strategy to incorporate PCMs into gypsum composites through fly ash cenosphere-encapsulated PCM, namely CenoPCM, aiming to enhance the mechanical properties and thermal conductivity over existing commercial counterparts. An experimental program was conducted to study the impact of the inclusion of CenoPCM on the mechanical and thermal performance of gypsum composites, and the results were compared to those of commercially available polymerencapsulated PCM benchmark (Micronal). The findings highlighted that PCM-charged samples exhibited up to 95.90 J/g (CenoPCM) of latent heat with 70 % CenoPCM loading. The results of mechanical tests also showed that CenoPCM outperformed its polymer-encapsulated counterpart, achieving 55 % higher mechanical strength on average. Here, this improvement is attributed to the rigid shell of fly ash cenosphere (FAC) serving as a PCM carrier, providing a skeleton-like structure to gypsum composites for higher load-bearing capacity. Additionally, hotbox tests demonstrated that the CenoPCM-charged wall panels yielded a 20 % higher thermal conductivity and a 22 % increased time lag compared to Micronal PCM-charged panels, indicating its potential to shift the peak load in buildings.

Ceno PCM↗
DOE OSTI2020

Robust PCA-Deep Belief Network Surrogate Model for Distribution System Topology Identification with DERs

With the expansion of distribution networks and increased penetration of distributed energy resources (DERs), it is becoming increasingly important to obtain accurate distribution network topology in real-time. In this paper, a robust principal component analysis coupled deep belief network (PCA-DBN) surrogate model is proposed for distribution system topology identification. It integrates the benefits of robust feature extraction from PCA to deal with data quality issues and filter out noise, and the strength of DBN in capturing the nonlinear relationship between voltage amplitudes and the binary states of switchable connections. This also significantly reduces the DBN training complexity without loss of accuracy. It is shown that the widely used standard deviation of voltage drop and the voltage covariance matrix features yield less accuracy as compared to that of the voltage amplitudes in presence of high penetration of DERs and ZIP loads. Comparison results with other alternatives, such as the random forest (RF), multi-output regression (MOR) and the traditional DBN methods demonstrate that the proposed method can achieve a much higher topology identification accuracy while maintaining robustness to missing data and measurement noise under various penetration levels of DERs.

deep belief network↗
DOE OSTI2025

Intercomparison of Deep Learning Model Architectures for Atmospheric River Prediction

With a rapid surge in the application of machine learning (ML) for a diverse range of tasks in climate science, the present study addresses a challenge for climate scientists when selecting the optimal ML or deep learning (DL) architecture for a given application. In particular, a DL intercomparison study was performed with a focus on forecasting the position of atmospheric rivers (ARs) on short-range time scales (up to 5-day lead times). AR predictions from multiple DL architectures, including various types of convolutional autoencoders and a vision transformer (ViT), were compared against ECMWF ERA5 reanalysis and hindcasts from a global climate model. DL models with similar trainable parameters were trained on ERA5 reanalysis data and AR positions derived from a thresholding algorithm to ensure a fair comparison among the DL models. Each model’s performance and accuracy in forecasting AR location and key input fields within a 5-day window were assessed using metrics of root-mean-square error, anomaly correlation, and mean intersection over union. The ViT architecture outperformed other autoencoder models in most of the metrics. Incorporating additional meteorological fields only yielded slight improvements in forecasting certain fields at longer lead times. The results also suggest that a smaller number of input time steps or smaller number of autoregressive steps can achieve better prediction skills, while also improving the overall computational efficiency. This research offers valuable insights into the strengths and weaknesses of different DL techniques for AR forecasting, hopefully guiding the development of improved models for forecasting this phenomenon.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Porous Polymer Structures with Tunable Mechanical Properties Using a Water Emulsion Ink

Recently, the manufacturing of porous polydimethylsiloxane (PDMS) with engineered porosity has gained considerable interest due to its tunable material properties and diverse applications. An innovative approach to control the porosity of PDMS is to use transient liquid phase water to improve its mechanical properties, which has been explored in this work. Adjusting the ratios of deionized water to the PDMS precursor during blending and subsequent curing processes allows for controlled porosity, yielding water emulsion foam with tailored properties. The PDMS-to-water weight ratios were engineered ranging from 100:0 to 10:90, with the 65:35 specimen exhibiting the best mechanical properties with a Young’s Modulus of 1.17 MPa, energy absorption of 0.33 MPa, and compressive strength of 3.50 MPa. This led to a porous sample exhibiting a 31.46% increase in the modulus of elasticity over a bulk PDMS sample. Dowsil SE 1700 was then added, improving the storage capabilities of the precursor. The optimal storage temperature was probed, with -60 °C resulting in great pore stability throughout a three-week duration. The possibility of using these water emulsion foams for paste extrusion additive manufacturing (AM) was also analyzed by implementing a rheological modifier, fumed silica. Fumed silica’s impact on viscosity was examined, revealing that 9 wt% of silica demonstrates optimal rheological behaviors for AM, bearing a viscosity of 10,290 Pa·s while demonstrating shear-thinning and thixotropic behavior. This study suggests that water can be used as pore-formers for PDMS in conjunction with AM to produce engineered materials and structures for aerospace, medical, and defense industries as sensors, microfluidic devices, and lightweight structures.

36 MATERIALS SCIENCE↗