Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface breakdown”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Positive ion emission from oxidized aluminum during ultraviolet excimer laser irradiation

We report quadrupole mass-selected time-of-flight measurements of positive ions from oxidized aluminum metal (and for comparison, single-crystal sapphire) during pulsed excimer laser irradiation at 193 and 248 nm. This work focuses on laser fluences well below onset of rapid etching or optical breakdown. By far the most intense emissions are due to Al{sup +}. On previously unexposed material, the ion kinetic energies are initially well above the photon energy, consistent with the ejection of Al{sup +} sorbed at surface electron traps. During prolonged irradiation, the emission intensities and kinetic energies gradually fall. Emission from patches of oxide would account for previous reports of laser-induced Al{sup +} emission from metallic aluminum surfaces cleaned by ion etching if patches of thin oxide were to survive the etching treatment.

36 MATERIALS SCIENCE↗

Photocathode emission studies: Dark current and Schottky-enabled photo-electrons in a high-field RF gun

We report on dark current and Schottky-enabled photoemission from a copper photocathode surface. Field-emitted dark current is a major gradient-limiting factor in RF cavities. Field emission is generally attributed to geometrical projections on the bulk surface whose field enhancement factor ({beta}) and the emitting area (A{sub e}) can be extracted from the Fowler-Nordheim (FN) plot. Measurements were made at Tsinghua S-band RF gun facility in two separate experiments. Using the traditional FN formula for RF fields we discovered that field enhancement factor ({beta}) alone cannot explain the full data set. Instead, we found that a low work function at some sites is required. In addition, surface analysis of the cathode after the experiment shows that geometric {beta} indicated would be < 10. Thus we conclude that low work function sites with a small {beta} are responsible for dark current emission and subsequent breakdown in high-gradient structures. The origin of these sites is unclear but could be due to defects or impurities.

43 PARTICLE ACCELERATORS↗

Thermographic process monitoring in powderbed based additive manufacturing

Selective Laser Melting is utilized to build metallic parts directly from CAD-Data by solidification of thin powder layers through application of a fast scanning laser beam. In this study layerwise monitoring of the temperature distribution is used to gather information about the process stability and the resulting part quality. The heat distribution varies with different kinds of parameters including scan vector length, laser power, layer thickness and inter-part distance in the job layout which in turn influence the resulting part quality. By integration of an off-axis mounted uncooled thermal detector the solidification as well as the layer deposition are monitored and evaluated. Errors in the generation of new powder layers usually result in a locally varying layer thickness that may cause poor part quality. For effect quantification, the locally applied layer thickness is determined by evaluating the heat-up of the newly deposited powder. During the solidification process space and time-resolved data is used to characterize the zone of elevated temperatures and to derive locally varying heat dissipation properties. Potential quality indicators are evaluated and correlated to the resulting part quality: Thermal diffusivity is derived from a simplified heat dissipation model and evaluated for every pixel and cool-down phase of a layer. This allows the quantification of expected material homogeneity properties. Maximum temperature and time above certain temperatures are measured in order to detect hot spots or delamination issues that may cause a process breakdown. Furthermore, a method for quantification of sputter activity is presented. Since high sputter activity indicates unstable melt dynamics this can be used to identify parameter drifts, improper atmospheric conditions or material binding errors. The resulting surface structure after solidification complicates temperature determination on the one hand but enables the detection of potential surface defects on the other hand. These issues and proper key figures for thermographic monitoring of the Selective Laser Melting process are discussed in the paper. Even though microbolometric temperature measurement is limited to repetition rates in the Hz-regime and sub megapixel resolution, current results show the feasibility of process surveillance by thermography for a limited section of the building platform in a commercial system.

42 ENGINEERING↗

Experimental investigation of the flow on the suction side of a thin Delta wing

Surface oil flow patterns were photographed and pressure distribution measurements were carried out on a sharp edged delta wing of aspect ratio lambda = 1.0 in order to determine the influence of Reynolds number and of vortex breakdown on the flow on the suction side of the wing. The formation of the secondary vortex occurs due to separation of a laminar boundary layer in the front part of the wing and due to separation of a turbulent boundary layer in the rear part of the wing. In the case of turbulent separation, the secondary separation line is closer to the wing leading edge than in the laminar case. The position of the transition depends on the Reynolds number and on the angle of incidence. The breakdown of a vortex above the wing leads to a kink in the secondary separation line.

Hummel, D.↗

Contact method to allow benign failure in ceramic capacitor having self-clearing feature

A capacitor exhibiting a benign failure mode has a first electrode layer, a first ceramic dielectric layer deposited on a surface of the first electrode, and a second electrode layer disposed on the ceramic dielectric layer, wherein selected areas of the ceramic dielectric layer have additional dielectric material of sufficient thickness to exhibit a higher dielectric breakdown voltage than the remaining majority of the dielectric layer. The added thickness of the dielectric layer in selected areas allows lead connections to be made at the selected areas of greater dielectric thickness while substantially eliminating a risk of dielectric breakdown and failure at the lead connections, whereby the benign failure mode is preserved.

47 OTHER INSTRUMENTATION↗

Mathematical Modeling of Hydroxide-Exchange-Membrane Water Electrolyzer

Water electrolyzers can transform intermittent renewable energy like solar energy and wind energy into the chemical energy of hydrogen with zero greenhouse-gas emissions. The hydroxide-exchange membrane electrolyzer (HEME) combines the capability to produce pressurized hydrogen with the advantage of being able to use low or non-platinum group metal (PGM) electrocatalysts in the alkaline environment.1 Hydroxide salts, for example, KOH, are added to the HEME water feed on both anode and cathode to improve its performance. However, the specific mechanism of performance improvement still needs to be further understood. In addition, at high current densities, bubble evolution can result in mass-transport limitations, a less well studied phenomena. Mathematical modeling is ideal to explore these issues as it is cost and time efficient and can deconvolute the physics, processes, and observed phenomena and study the applied-voltage breakdown. In this work, we extend our previously developed 1D two-phase continuum model2 to study the varies processes in the HEME and provide insights on performance optimizations. First, the oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) kinetics at different hydroxide concentrations have been studied by rotating disk electrodes (RDE) and implemented in the model. Then, the model is calibrated and validated against experimental HEME polarization curves for different KOH concentrations as a liquid electrolyte. The model clearly shows a performance increase with increasing KOH concentrations, which is consistent with the experimental results. The reduced ohmic resistance and increased electrochemical active surface area (ECSA) are the two main reasons for performance increase. The large amount of hydroxide in the liquid electrolyte not only helps to distribute the reactant hydroxide throughout the catalyst layer (CL), which reduces ohmic loss, but also enables reaction at the interface between the liquid electrolyte and electrocatalyst, which increases the ECSA. Applied-voltage breakdown demonstrates that the electrolyzer performance is dominated by anode kinetics and ohmic loss. A comparison with the DI water feed shows a more uniform current distribution in the anode CL when KOH is added, which indicates a higher utilization of the CL. Second, we present modeling on the effects of bubble coverage. As gas evolves, part of the ECSA is minimized due to bubble coverage. To account for this effect, an empirical relationship between the fractional bubble coverage and the current density is implemented in the model.3 The model shows this bubble coverage effect is more pronounced at large current densities with DI water feed. Acknowledgements This work was funded under the HydroGEN Consortium by the Energy Efficiency and Renewable Energy, Hydrogen and Fuel Cell Technologies Office, of the U. S. Department of Energy under contract number DE-AC02-05CH11231. References R. Abbasi, B. P. Setzler, S. Lin, J. Wang, Y. Zhao, H. Xu, B. Pivovar, B. Tian, X. Chen, G. Wu and Y. Yan, 31, 1805876 (2019). L. N. Stanislaw, M. R. Gerhardt and A. Z. Weber, ECS Transactions, 92, 767 (2019). H. Vogt and R. J. Balzer, Electrochimica Acta, 50, 2073 (2005).

Liu, Jiangjin↗

Role of Surface Termination in the Metal–Insulator Transition of V 2 O 3 (0001) Ultrathin Films

Surface termination is known to play an important role in determining the physical properties of materials. It is crucial to know how surface termination affects the metal–insulator transition (MIT) of V 2 O 3 films for both fundamental understanding and its applications. By changing growth parameters, we achieved a variety of surface terminations in V 2 O 3 films that are characterized by low-energy electron diffraction (LEED) and photoemission spectroscopy techniques. Depending upon the terminations, our results show that MIT can be partially or fully suppressed near the surface region due to the different fillings of the electrons at the surface and subsurface layers and the change of screening length compared to the bulk. Across MIT, a strong redistribution of spectral weight and its transfer from a high-to-low-binding energy regime is observed in a wide energy scale. Our results show that the total spectral weight in the low-energy regime is not conserved across MIT, indicating a breakdown of the “sum rules of spectral weight”, signature of a strongly correlated system. Such a change in spectral weight is possibly linked to the change in hybridization, lattice volume (i.e., effective carrier density), and the spin degree of freedom in the system that occurs across MIT. We find that MIT in this system is strongly correlation-driven, where the electron–electron interactions play a pivotal role. Furthermore, our results provide better insight into the understanding of the electronic structure of strongly correlated systems and highlight the importance of accounting for surface effects during interpretation of the physical property data mainly using surface-sensitive probes, such as surface resistivity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

HVDC Surface Flashover in Compressed Air for Various Dielectrics

Here, this study measures the voltage at which flashover occurs in compressed air for a variety of dielectric materials and lengths in a uniform field for DC voltages up to 100 kV. Statistical time lag is recorded and characterized, displaying a roughly exponential dependence on breakdown voltage. Of the materials tested, acrylic is observed to be the most resistant to flashover. These data are intended to facilitate the design of compressed-air insulated high voltage systems as an alternative to SF 6 insulated systems.

42 ENGINEERING↗

F-18 high alpha research vehicle surface pressures: Initial in-flight results and correlation with flow visualization and wind-tunnel data

Pressure distributions measured on the forebody and the leading-edge extensions (LEX's) of the NASA F-18 high alpha research vehicle (HARV) were reported at 10 and 50 degree angles of attack and at Mach 0.20 to 0.60. The results were correlated with HARV flow visualization and 6-percent scale F-18 wind-tunnel-model test results. The general trend in the data from the forebody was for the maximum suction pressure peaks to first appear at an angle of attack (alpha) of approximately 19 degrees and increase in magnitude with angle of attack. The LEX pressure distribution general trend was the inward progression and increase in magnitude of the maximum suction peaks up to vortex core breakdown and then the decrease and general flattening of the pressure distribution beyond that. No significant effect of Mach number was noted for the forebody results. However, a substantial compressibility effect on the LEX's resulted in a significant reduction in vortex-induced suction pressure as Mach number increased. The forebody primary and the LEX secondary vortex separation lines, from surface flow visualization, correlated well with the end of pressure recovery, leeward and windward, respectively, of maximum suction pressure peaks. The flight to wind-tunnel correlations were generally good with some exceptions.

Fisher, David F.↗

Wettability of graphitic-carbon and silicon surfaces: MD modeling and theoretical analysis

The wettability of graphitic carbon and silicon surfaces was numerically and theoretically investigated. A multi-response method has been developed for the analysis of conventional molecular dynamics (MD) simulations of droplets wettability. The contact angle and indicators of the quality of the computations are tracked as a function of the data sets analyzed over time. This method of analysis allows accurate calculations of the contact angle obtained from the MD simulations. Analytical models were also developed for the calculation of the work of adhesion using the mean-field theory, accounting for the interfacial entropy changes. A calibration method is proposed to provide better predictions of the respective contact angles under different solid-liquid interaction potentials. Estimations of the binding energy between a water monomer and graphite match those previously reported. In addition, a breakdown in the relationship between the binding energy and the contact angle was observed. The macroscopic contact angles obtained from the MD simulations were found to match those predicted by the mean-field model for graphite under different wettability conditions, as well as the contact angles of Si(100) and Si(111) surfaces. Finally, an assessment of the effect of the Lennard-Jones cutoff radius was conducted to provide guidelines for future comparisons between numerical simulations and analytical models of wettability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

RF Choke for Standing Wave Structures and Flanges

SLAC participates in the U.S. High Gradient collaboration whose charter includes basic studies of rf breakdown properties in accelerating structures. These studies include experiments with different materials and construction methods for single cell standing wave accelerating structures. The most commonly used method of joining cells of such structures is the high temperature bonding and/or brazing in hydrogen and/or vacuum. These high temperature processes may not be suitable for some of the new materials that are under consideration. We propose to build structures from cells with an rf choke, taking the cell-to-cell junction out of the electromagnetic field region. These cells may be clamped together in a vacuum enclosure, the choke joint ensuring continuity of rf currents. Next, we propose a structure with a choke joint in a high gradient cell and a view port which may allow us microscopic, in-situ observation of the metal surface during high power tests. And third, we describe the design of a TM01 choke flange for these structures.

08 HYDROGEN↗

Capacitance-voltage characteristics of (Al/Ti)/Al{sub 2}O{sub 3}/n-GaN MIS structures

The capacitance-voltage characteristics of (Al/Ti)/Al{sub 2}O{sub 3}/n-GaN metal—insulator-semiconductor (MIS) structures are measured and analyzed. n-Type GaN films are grown on sapphire (0001) substrates by the metal-organic chemical vapor deposition method. An aluminum-oxide layer with a thickness of 60 nm is deposited onto the surface of GaN by the method of atomic-layer deposition from the gas phase. Metallic contacts are deposited by the electron-beam evaporation of titanium and aluminum in vacuum. According to the measurement results, the breakdown-field strength of the oxide, its dielectric constant, and the integrated electron density of states at the oxide-semiconductor interface are 5 × 10{sup 6} V/cm, 7.5, and 3 × 10{sup 12} cm{sup −2}, respectively.

36 MATERIALS SCIENCE↗

Midlatitude Oceanic Cloud and Precipitation Properties as Sampled By the ARM Eastern North Atlantic Observatory

Marine low clouds are critical to the climate system because of their extensive coverage and associated controls on boundary layer dynamics and radiative energy balance. The primary foci for this study are marine low cloud observations over a heavily instrumented site on the Azores archipelago in the eastern North Atlantic (ENA) and their associated raindrop size distribution (DSD) properties, relative low-cloud contributions to the precipitation, and additional sampling (instrument, environmental) considerations. The contribution from low clouds (e.g., cloud top < 4 km) to the overall precipitation over midlatitude oceans is poorly understood, in part because of the lack of coupled, high-quality measurements of precipitation and low-cloud properties. Cloud regime and precipitation breakdowns performed for a multi-year record emphasize the diurnal precipitation cycle and DSD characteristics for both low and deeper clouds. Results demonstrate that marine low clouds over this ENA location account for a significant (45%) contribution to the total rainfall and exhibit a diurnal cycle in cloud (thickness, top, base) and precipitation characteristics similar to satellite records. Additional controls on observed surface rainfall characteristics of low clouds allowed by the extended ground-based facility datasets are also explored. From those analyses, it is suggested that the synoptic state exerts a significant control on low-cloud and surface precipitation properties.

Giangrande, Scott↗

Laboratory simulation of irradiation-induced dielectric breakdown in spacecraft charging

The discharging of dielectric samples irradiated by a beam of monoenergetic electrons is investigated. The development of a model, or models, which describe the discharge phenomena occuring on the irradiated dielectric targets is discussed. The electrical discharge characteristics of irradiated dielectric samples are discussed and the electrical discharge paths along dielectric surfaces and within the dielectric material are determined. The origin and destination of the surface emitted particles is examined and the charge and energy balance in the system is evaluated.

Yadlowsky, E. J.↗

Simulating Underexpanded Jets in Martian and Lunar Environments

As part of the Game Changing Development (GCD) Program, funded by NASA’s Space Technology Mission Directorate (STMD), the development of simulation capability for the prediction of extra-terrestrial Plume Surface Interaction (PSI) environments has been undertaken by the Fluid Dynamics Branch at NASA/MSFC. The GCD PSI Project, planned to be accomplished over a four year period, contains a Predictive Simulation Capability (PSC) Element focused on creating simulation capability for the reliable and accurate prediction of PSI in Martian (~650 Pa) and Lunar (vacuum) ambient environments. In addition to the PSC Element, the PSI Project also contains a companion Ground Testing Element for development of focused datasets for validation of predictive capability as well as a Flight-focused Instrumentation Element. This paper describes the activities and accomplishments in the past year for the Prediction of Plume Flow in low pressure environments component of the PSI Project. While the Loci/Chem Computational fluid dynamics (CFD) application has been validated and used extensively for simulating launch environments in atmospheric conditions, use of this tool for simulating supersonic plumes at Mars-like ambient pressure requires further validation. CFD simulations of underexpanded jets have been performed using Loci/Chem for Mars-like conditions to predict several metrics for steady laminar, turbulent, and impinging plumes. The CFD results are compared with an experimental data set for low Reynolds number plumes at these conditions in order to evaluate the current capability of the Loci/Chem tool for these types of environments. The CFD validation results to date show reasonable agreement with the experimental data across all of the metrics of interest for the configurations considered. The Loci/Chem-Boltzmann CFD application is a hybrid continuum/rarefied flow solver which extends modeling capabilities to very low pressure environments such as those on the Moon. The Loci/Chem-Boltzmann solver uses a gradient-based continuum breakdown criterion to restrict solution of the computationally expensive Boltzmann equation to only a subset of the domain, while using the Navier-Stokes equations elsewhere. This CFD application is under active development, and current efforts toward establishing production ready capability for evaluating Lunar plume surface interactions are well under way. Initial simulations of an Apollo LEM indicate that several regions of the flow require solving the Boltzmann equations due to extreme rarefaction. Early simulations are promising, indicating reasonable overall computational time for a full 3D human scale lander simulation.

Thomas Shurtz↗

Wear modes active in angular contact ball bearings operating in liquid oxygen environment of the Space Shuttle turbopumps

Extensive experimental investigation has been carried out on used flight bearings of the high pressure oxidizer turbopumps (HPOTP) of the space shuttle main engine (SSME) in order to determine the dominant wear modes, their extent, and causes. The paper presents the methodology, various surface analysis techniques used, results, and discussion. The mode largely responsible for premature bearing wear has been identified as adhesive/shear peeling of the upper layers of bearing balls and rings. This mode relies upon the mechanisms of scale formation, breakdown, and removal, all of which are greatly enhanced by the heavy oxidation environment of the HPOTP. Major causes of the high wear rates appear to be lubrication and cooling, both inadequate for the imposed conditions of operation. Numerous illustrations and evidence are provided.

Chase, Thaddeus J.↗

Stationary Crossflow Breakdown due to Mixed Mode Spectra of Secondary Instabilities

Numerical simulations are used to study laminar breakdown characteristics associated with stationary crossflow instability in the boundary-layer flow over a subsonic swept-wing configuration. Previous work involving the linear and nonlinear development of individual, fundamental modes of secondary instability waves is extended by considering the role of more complex, yet controlled, spectra of the secondary instability modes. Direct numerical simulations target a mixed mode transition scenario involving the simultaneous presence of Y and Z modes of secondary instability. For the initial amplitudes investigated in this paper, the Y modes are found to play an insignificant role during the onset of transition, in spite of achieving rather large, O(5%), amplitudes of RMS velocity fluctuation prior to transition. Analysis of the numerical simulations shows that this rather surprising finding can be attributed to the fact that the Y modes are concentrated near the top of the crossflow vortex and exert relatively small influence on the Z modes that reside closer to the surface and can lead to transition via nonlinear spreading that does not involve interactions with the Y mode. Finally, secondary instability calculations reveal that subharmonic modes of secondary instability have substantially lower growth rates than those of the fundamental modes, and hence, are less likely to play an important role during the breakdown process involving complex initial spectra.

Li, Fei↗

Influence of Stationary Crossflow Modulation on Secondary Instability

A likely scenario for swept wing transition on subsonic aircraft with natural laminar flow involves the breakdown of stationary crossflow vortices via high frequency secondary instability. A majority of the prior research on this secondary instability has focused on crossflow vortices with a single dominant spanwise wavelength. This paper investigates the effects of the spanwise modulation of stationary crossflow vortices at a specified wavelength by a subharmonic stationary mode. Secondary instability of the modulated crossflow pattern is studied using planar, partial-differential-equation based eigenvalue analysis. Computations reveal that weak modulation by the first subharmonic of the input stationary mode leads to mode splitting that is particularly obvious for Y-type secondary modes that are driven by the wall-normal shear of the basic state. Thus, for each Y mode corresponding to the fundamental wavelength of results in unmodulated train of crossflow vortices, the modulated flow supports a pair of secondary modes with somewhat different amplification rates. The mode splitting phenomenon suggests that a more complex stationary modulation such as that induced by natural surface roughness would yield a considerably richer spectrum of secondary instability modes. Even modest levels of subharmonic modulation are shown to have a strong effect on the overall amplification of secondary disturbances, particularly the Z-modes driven by the spanwise shear of the basic state. Preliminary computations related to the nonlinear breakdown of these secondary disturbances provide interesting insights into the process of crossflow transition in the presence of the first subharmonic of the dominant stationary vortex.

Vortex structure↗