Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “sublimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Determination of convective diffusion heat/mass transfer rates to burner rig test targets comparable in size to cross-stream jet diameter

Two sets of experiments have been performed to be able to predict the convective diffusion heat/mass transfer rates to a cylindrical target whose height and diameter are comparable to, but less than, the diameter of the circular cross-stream jet, thereby simulating the same geometric configuration as a typical burner rig test specimen located in the cross-stream of the combustor exit nozzlle. The first set exploits the naphthalene sublimation technique to detetermine the heat/mass transfer coefficient under isothermal conditions for various flow rates (Reynolds numbers). The second set, conducted at various combustion temperatures and Reynolds numbers, utilized the temperature variation along the surface of the above-mentioned target under steady-state conditions to estimate the effect of cooling (dilution) due to the entrainment of stagnant room temperature air. The experimental information obtained is used to predict high temperature, high velocity corrosive salt vapor deposition rates in burner rigs on collectors that are geometrically the same. The agreement with preliminary data obtained from Na2S04 vapor deposition experiments is found to be excellent.

Gokoglu, S. A.↗

Encapsulating X-Ray Detectors

Vapor-deposited polymer shields crystals from environment while allowing X rays to pass. Polymer coating transparental to X rays applied to mercuric iodide detector in partial vacuum. Coating protects crystal from sublimation, chemical attack, and electrical degradation.

Conley, Joseph M.↗

Lidar measurement of stratospheric aerosol at Syowa Station, Antarctica

Lidar measurement on Antarctic aerosols were made during the Antarctic Middle Atmosphere (AMA) period, 1983 to 1985, at Syowa Station. Topics measured are winter enhancement aerosol layer and volcanic effect of El Chichon on the Antarctic stratosphere aerosols. The large depolarization ratio (maximum value was about 0.8) seems to support sublimation growth of ice crystals. The lidar measurements showed a meaningful time lag between aerosol content increase and depolarization ratio increase. Considering the balloon observations made in early winter, it was speculated that an increase in large particle number concentration also contributed to the winter enhancement. The El Chichon cloud spread to the Antarctic region by the beginning of 1983. The temporal change of integrated backscatter coefficient shows a clear decay pattern, although strong winter enhancement superposes.

Iwasaka, Y.↗

A continued program of planetary study at the University of Texas McDonald Observatory

The beginning of eclipses of the Pluto-Charon system was detected. The onset of coma formation of P/Halley at 5.4 au was detected and evidence of sublimation at 4.8 au when CN emission was detected. Extensive spatial maps of the gas in the comae of comets Halley and Giacobini-Zinner were obtained in fall 1985. Halley was time variable, and Giacobini-Zinner was depleted in C2 and C3 relative to CN. Comet Kopff was shown to have a pre-perihelion brightness maximum of its gas, consistent with mantle development if the comet is a high obliquity object. New Haser model scale lengths for CN, C3, and C2 were determined using results from the Faint Comet Survey. Spectra of 12 asteroids in unusual orbits showed no evidence of any comet-like emission features. In particular, 3200 Phaethon (1983 TB) has no gas or dust coma, in spite of the similarity of its orbit with the Geminid meteor stream. Data were analyzed on Saturn's H2 and CH4 bands for the recent southern summer using a Tomasko-Doose type of haze distribution. This haze model fits the data moderately well, giving a CH4 mixing ratio of (4.2 + or 0.4)x003. Simple functions were found to approximate the collision-induced rotation-translation thermal opacity of H2.

Smith, H. J.↗

On seasonal variations of Mars' gravitational field

A great quantity of CO2 is exchanged between the Martian atmosphere and polar caps in the course of a Martian year. This exchange occurs in seasonal cycles: CO2 condenses to form the polar caps in winter and sublimes into the atmosphere in summer. The mass involved is about 25% of the total mass of the Martian atmosphere. This paper studies the effects of the CO2 mass redistribution on the Mars' gravitational field. Two mechanisms are examined: (1) the waxing and waning of solid CO2 in the polar caps, and (2) the geographical distribution of gaseous CO2 in the atmosphere. The maximum changes produced by (1) in the low-degree zonal J sub l harmonics in the Mars gravitational field are found to be as much as 7.5 x 10 to the-9 power for J sub 2 (corresponding to 1.1 cm change in the geoid), and about half as much for J sub 3. The effect of (2) on some most prominent low-degree harmonics (for l =1-3) in the effective topography (defined as the departure of the true topography from the geoid) is also evaluated. Their magnitudes are large by Earth standards. Whether they can be observed by the upcoming Mars Observer is still uncertain.

Chao, B. Fong↗

Moisture driven convection on Jupiter: A mechanism to produce the equatorial plumes

Possible roles are explored for moist convection in the production of bright plume features in the Jupiter atmosphere. The features have been observed at least since 1881. A one-dimensional model is developed for a Jovian cloud and the conditions necessary for convection to occur on Jupiter are defined. The model is used to predict the vertical velocity and maximum altitude of moist clouds that are convected over a vertical extent of 100, 10 and 1 km. Convection within the ammonia layer would not produce sufficient buoyancy to sublime from the rising air parcel. Water rising from the 5 bar to 1 bar level could carry enough ammonia to the cooler region to form plume anvils in the stable layer above 700 mbar. If unpolluted during the convection, the water could be the source of high altitude haze above the entire equatorial zone.

Stoker, C.↗

Temperatures and minimum thickness of the inactive surface layer of comet Halley

The effects of a nonvolatile mantle on the thermal state of a comet nucleus are investigated. The original computer model was modified so that temperatures can be computed through a thin dust mantle to the center of a 5 km spherical nucleus in the orbit of P/Halley. No attempt is made to simulate the formation of the mantle. Results are obtained for various specified values of initial mantle thickness and thermal conductivity to determine their effects on temperature profiles through the mantle. The minimum thickness of mantle that can withstand ejection by sublimating gasses is also calculated as a function of mantle thermal conductivity. Calculations were performed for ten or more orbits until temperatures in the mantle reached a near steady state. Results indicate that mantles as thin as 4 cm and 14 cm, for thermal conductivities of 600 and 6000 ergs/cm/s K, respectively, will remain intact. Surface temperatures as high as 511 K at perihelion and 400 K at the position of spacecraft encounter were computed at 0 degree latitude for an upright, rotating nucleus. Ice interface temperatures were raised by different amounts during each orbit, depending on mantle thickness and thermal conductivity, until steady state was reached. These results imply that relatively small nonvolatile masses emplaced randomly in comet nuclei could produce an irregular, permanently mantled surface and could also account for the apparently random location of active areas.

Fanale, F. P.↗

Dynamics of long period comets

The appearance of Halley's Comet in 1985 to 1986 and the related emphasis on research on physical models of cometary nuclei, led to a more moderate pace for the dynamical studies of the Oort cloud and the motion of long-period comets this year. Specific areas studied included the dynamical evolution of cometary showers as a result of stars passages through the inner Oort cloud and the possible relationship to observed stepwise mass extinctions at geological boundaries, revised estimates for the total mass of comets in the Oort cloud as a result of lessons learned from the spacecraft encounters with Halley's Comet, and study of the possible dynamical sources for the short-period comets in the solar system as part of a wider study of physical processing of cometary nuclei prior to their becoming visible comets. The work on cometary showers used a Monte Carlo simulation of the evolution of cometary orbits under a combination of planetary, nongravitational, and stellar perturbations, and with physical removal by disruption, sublimation of all volatiles, and collision.

Weissman, Paul R.↗

Flow-separation patterns on symmetric forebodies

Flow-visualization studies of ogival, parabolic, and conical forebodies were made in a comprehensive investigation of the various types of flow patterns. Schlieren, vapor-screen, oil-flow, and sublimation flow-visualization tests were conducted over an angle-of-attack range from 0 deg. to 88 deg., over a Reynolds-number range from 0.3X10(6) to 2.0X10(6) (based on base diameter), and over a Mach number range from 0.1 to 2. The principal effects of angle of attack, Reynolds number, and Mach number on the occurrence of vortices, the position of vortex shedding, the principal surface-flow-separation patterns, the magnitude of surface-flow angles, and the extent of laminar and turbulent flow for symmetric, asymmetric, and wake-like flow-separation regimes are presented. It was found that the two-dimensional cylinder analogy was helpful in a qualitative sense in analyzing both the surface-flow patterns and the external flow field. The oil-flow studies showed three types of primary separation patterns at the higher Reynolds numbers owing to the influence of boundary-layer transition. The effect of angle of attack and Reynolds number is to change the axial location of the onset and extent of the primary transitional and turbulent separation regions. Crossflow inflectional-instability vortices were observed on the windward surface at angles of attack from 5 deg. to 55 deg. Their effect is to promote early transition. At low angles of attack, near 10 deg., an unexpected laminar-separation bubble occurs over the forward half of the forebody. At high angles of attack, at which vortex asymmetry occurs, the results support the proposition that the principal cause of vortex asymmetry is the hydrodynamic instability of the inviscid flow field. On the other hand, boundary-layer asymmetries also occur, especially at transitional Reynolds numbers. The position of asymmetric vortex shedding moves forward with increasing angle of attack and with increasing Reynolds number, and moves rearward with increasing Mach number.

Keener, Earl R.↗

Experimental studies on the stability and transition of 3-dimensional boundary layers

Three-dimensional unstable boundary layers were investigated as to their characteristic instabilities, leading to turbulence. Standing cross-flow instabilities and traveling waves preceding the transition were visualized with the hydrogen bubble technique in the boundary layer above the wall of a swept cylinder. With the sublimation method and hot film technique, a model consisting of a swept flat plate with a pressure-inducing displacement body in the 1 m wind tunnel was studied. Standing waves and traveling waves in a broad frequency are observed. The boundary layer of this model is close to the assumptions of the theory.

Nitschke-Kowsky, P.↗

Spectrophotometric observations of Comet Halley

Comet Halley was observed using an intensified dissector scanner spectrograph on the 2.7 m telescope at McDonald Observatory from Dec. 1984 through June 1986. Molecular emissions were first detected in February 1985 when CN was observed. Spatial maps probing different regions of the coma were made starting in November 1985. Haser model production rates were computed for each night's data. The brightness of Halley, and therefore the production rates, are variable on timescales of a day, with variations of a magnitude or more in this time period. Nonequilibrium chemical models were calculated using Giotto and Vega data as constraints and inputs. The variability of Halley cannot be explained solely by water sublimation, nor do the variations show the 52 to 53 hr period of rotation.

Cochran, A. L.↗

Measurement of the effect of manufacturing deviations on natural laminar flow for a single engine general aviation airplane

Renewed interest in natural laminar flow (NLF) had rekindled designer concern that manufacuring deviations may destroy the effectiveness of NLF for an operational aircraft. Experiments are summarized that attemtped to measure total drag changes associated with three different wing surface conditions on an aircraft typical of current general aviation high performance singles. The speed power technique was first used in an attempt to quantify the changes in total drag. Predicted and measured boundary layer transition locations for three different wing surface conditions were also compared, using two different forms of flow visualization. The three flight test phases included: assessment of an unpainted airframe, flight tests of the same aircraft after painstakingly filling and sanding the wings to design contours, and similar measurement after this aricraft was painted. In each flight phase, transition locations were monitored using with sublimating chemicals or pigmented oil. Two-dimensional drag coefficients were estimated using the Eppler-Somers code and measured with a wake rake in a method very similar to Jones' pitot traverse method. The net change in two-dimensional drag coefficient was approximately 20 counts between the unpainted aircraft and the hand-smoothed aircraft for typical cruise flight conditions.

Source record↗

Post-perihelion brightening of Halley's Comet: A case of nuclear summer

Increased brightness and gas production rates for Halley's comet after perihelion are explained as a result of seasonal effects on an obliquely rotating nucleus. The highly eccentric cometary orbit causes a rapid change in solar declination as the comet rounds perihelion, resulting in drastic changes in the insolation reaching the Northern and Southern Hemispheres of the nucleus. The rapid heating of the Northern Hemisphere post-perihelion likely results in substantial cracking of the non-volatile surface crust due to thermal stresses, exposing areas of fresh volatile ices. The orientation of the triaxial ellipsoid nucleus may also play a role in exposing more surface area to continuous sunlight and sublimation after perihelion. Post-perihelion brightening models based on heat flow and storage in sub-surface layers of the nucleus pre-perihelion are likely not viable because of the low thermal conductivities of porous, low density cometary surface materials.

Weissman, Paul R.↗

Experimental studies on Taylor-Goertler vortices

Taylor-Goertler vortices arise in boundary layer along concave surfaces due to centrifugal effects. These counter-rotating streamwise vortices are one of three known flow instabilities which lead to boundary layer transition. Coupled with Tollmien-Schlichting waves and cross flow vortices, Taylor-Goertler vortices can triggerr early transition to turbulence. The flow field patterns were studied by flow visualization using a sublimating chemical technique and a three component laser velocimeter was used to study the flow field in the test region. Results from these studies are given and briefly discussed.

Goglia, G. L.↗

Moist convection - A mechanism for producing the vertical structure of the Jovian equatorial plumes

Possible roles are explored for moist convection in the production of bright plume features in the Jupiter atmosphere. The features have been observed at least since 1881. A one-dimensional model is developed for a Jovian cloud and the conditions necessary for convection to occur on Jupiter are defined. The model is used to predict the vertical velocity and maximum altitude of moist clouds that are convected over a vertical extent of 100, 10 and 1 km. Convection within the ammonia layer would not produce sufficient buoyancy to sublime from the rising air parcel. Water rising from the 5 bar to 1 bar level could carry enough ammonia to the cooler region to form plume anvils in the stable layer above 700 mbar. If unpolluted during the convection, the water could be the source of high altitude haze above the entire equatorial zone.

Stoker, C. R.↗

A simple method for monitoring surface temperatures in plasma treatments

A method consisting of applying temperature markers on the specimen is described for measuring the highest temperature reached by very thin films in situ during deposition. In the first test setup, lowering the input power to 500 W only effected the 177-C marker, while increasing the input power to 1.25 kW effected the 274-C marker. In tests conducted in a dc plasma with markers placed on the uncooled cathode in Ar plasma, the maximum temperatures indicated by the thermocouple matched a change in color of the markers, and no effect of earlier sublimation or decomposition was noted.

Manory, R. R.↗

Influence of suction and curvature on the growth of Goertler vortices on an airfoil

Laser velocimetry (LV) was used to study the development of Goertler vortices in a laminar boundary layer on a 1.83 m chord airfoil model. The vortex pattern was visualized using a sublimating chemical technique. A fixed, essentially uniform vortex spacing was observed throughout the test region for any given freestream velocity but the vortex wavelength varied significantly with change in freestream velocity. An appreciable, abrupt decrease in streak contrast indicated vortex damping in the convex region and was confirmed by disturbance functions determined from LV measurements. Moderate variation in suction levels did not alter the vortex spacing but appreciably modified the vortex strength. The experimental results on the growth of Goertler vortices along the concave surface and the effect of suction are compared with results from linear stability theory.

Mangalam, S. M.↗

Thermal segregation of water ice on the Galilean satellites

The susceptibility of dirty ice surfaces to a water cold-trapping process in the Galilean satellites' local bright patches, in association with preferential removal from dark areas, is inferred on the basis of a consideration of the thermal sublimation of ice. A decade time-scale segregation of the surface into bright icy regions and dark ice-free lag deposit regions would be the main consequence of such a process. While ion sputtering and micrometeorite bombardment do not appear to be of sufficient magnitude for a prevention of the process on Callisto and Ganymede, sputtering on the trailing side of Europa may be able to prevent segregation.

Spencer, John R.↗