Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “shape analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Calculation of Hub Loads at Low Airspeeds with Active Control

The effect of individual blade control (IBC) on the full-scale, low airspeed, level flight UH-60A oscillatory fixed system 4P hub loads and the rotating system blade bending moments is studied. The effect of a single 3P IBC input has been considered in this analytical study. At the low speed under consideration, it has been found that convergence of the comprehensive analysis is important for obtaining good predictions. Good correlation has been obtained with the measured full-scale wind tunnel data for the shapes of the fixed system 4P hub loads variations with the 3P IBC input phase, and also for the "best" phase of the 3P input (for minimum hub loads). The blade bending moment comparison shows mixed results. The 3P lead lag and the 4P flap bending moment trends with the 3P IBC input phase are reasonably predicted, whereas the 5P lead lag bending moment trend is not predicted well. Finally, the prediction of the baseline (no IBC) bending moments needs further study.

Kottapalli, Sesi↗

Blocked Force and Loading Calculations for LaRC THUNDER Actuators

An analytic approach is developed to predict the performance of LaRC Thunder actuators under load and under blocked conditions. The problem is treated with the Von Karman non-linear analysis combined with a simple Raleigh-Ritz calculation. From this, shape and displacement under load combined with voltage are calculated. A method is found to calculate the blocked force vs voltage and spring force vs distance. It is found that under certain conditions, the blocked force and displacement is almost linear with voltage. It is also found that the spring force is multivalued and has at least one bifurcation point. This bifurcation point is where the device collapses under load and locks to a different bending solution. This occurs at a particular critical load. It is shown this other bending solution has a reduced amplitude and is proportional to the original amplitude times the square of the aspect ratio.

Campbell, Joel F.↗

Development and use of computational techniques in Army Aviation research and development programs for crash resistant helicopter technology

During the 1960's over 30 full-scale aircraft crash tests were conducted by the Flight Safety Foundation under contract to the Aviation Applied Technology Directorate (AATD) of the U.S. Army Aviation Systems Command (AVSCOM). The purpose of these tests were to conduct crash injury investigations that would provide a basis for the formulation of sound crash resistance design criteria for light fixed-wing and rotary wing aircraft. This resulted in the Crash Survival Design Criteria Designer's Guide which was first published in 1967 and has been revised numerous times, the last being in 1989. Full-scale aircraft crash testing is an expensive way to investigate structural deformations of occupied spaces and to determine the decelerative loadings experienced by occupants in a crash. This gave initial impetus to the U.S. Army to develop analytical methods to predict the dynamic response of aircraft structures in a crash. It was believed that such analytical tools could be very useful in the preliminary design stage of a new helicopter system which is required to demonstrate a level of crash resistance and had to be more cost effective than full-scale crash tests or numerous component design support tests. From an economic point of view, it is more efficient to optimize for the incorporation of crash resistance features early in the design stage. However, during preliminary design it is doubtful if sufficient design details, which influence the exact plastic deformation shape of structural elements, will be available. The availability of simple procedures to predict energy absorption and load-deformation characteristics will allow the designer to initiate valuable cost, weight, and geometry tradeoff studies. The development of these procedures will require some testing of typical specimens. This testing should, as a minimum, verify the validity of proposed procedures for providing pertinent nonlinear load-deformation data. It was hoped that through the use of these analytical models, the designer could optimize aircraft design for crash resistance from both a weight and cost increment standpoint, thus enhancing the acceptance of the design criteria for crash resistance.

Burrows, Leroy T.↗

On self-preserving, variable-density, turbulent free jets

Published experimental data on incompressible, compresible, free binary, and confined binary turbulent axisymmetric jet flows are compiled and characterized, and the effect of varying turbulent diffusivity across the mixing region of a free jet is investigated analytically, applying the similarity-solution approach of So and Hwang (1986) to the self-preserving region. It is shown that closed-form solutions, represented by Gaussian error functions and having the turbulent Reynolds number and a profile-shape factor as free parameters, can be obtained if the turbulent diffusivities of momentum, mass, or heat are assumed to be different and to vary in both the streamwise and radial directions. An entrainment function uniquely related to the turbulent Reynolds number is derived, and good agreement between theoretical predictions and experimental measurements is demonstrated in graphs.

So, R. M. C.↗

Cooling flows in ellipticals and the nature of radio galaxies

Analytical arguments are presented to demonstrate that the morphology of the host galaxy will influence the type of radio signature emitted by the nucleus, which is in many cases presumed to a black hole. The types of matter inflows and consequent shapes of the accretion disks around the nuclei of spiral and elliptical galaxies are discussed. If the inflowing matter is predominantly cold and clumpy, then stars will tend to form and only the available hot gas will descend into the center. Collimated radio jets will appear only in the presence of hot interstellar gas in elliptical galaxies and not in spiral galaxies. The implications of the predictions for the interpretation of observational data on, e.g., BL Lac objects and N galaxies are discussed.

Begelman, M. C.↗

Combustor-diffuser interaction program

A collection of empirical and analytical design methodology on combustor-diffuser systems was completed. A fully elliptic code was selected for analyzing the combustor-diffuser interaction. Analytical model predictions were obtained for all flow conditions at which Phase 2 tests will be conducted. These results will be compared with laser doppler velocimeter data. Furthermore, a generalized nonorthogonal grid system is being developed to accurately simulate complex wall shapes.

Srinivasan, R.↗

A method to design blended rolled edges for compact range reflectors

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameter is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Gupta, Inder J.↗

A method to design blended rolled edges for compact range reflectors

A method to design blended rolled edges for arbitrary rim shape compact range reflectors is presented. The reflectors may be center-fed or offset-fed. The method leads to rolled edges with minimal surface discontinuities. It is shown that the reflectors designed using the prescribed method can be defined analytically using simple expressions. A procedure to obtain optimum rolled edges parameters is also presented. The procedure leads to blended rolled edges that minimize the diffracted fields emanating from the junction between the paraboloid and the rolled edge surface while satisfying certain constraints regarding the reflector size and the minimum operating frequency of the system.

Gupta, Inder J.↗

Nonlinear Pressurization and Modal Analysis Procedure for Dynamic Modeling of Inflatable Structures

An introduction and set of guidelines for finite element dynamic modeling of nonrigidized inflatable structures is provided. A two-step approach is presented, involving 1) nonlinear static pressurization of the structure and updating of the stiffness matrix and 2) hear normal modes analysis using the updated stiffness. Advantages of this approach are that it provides physical realism in modeling of pressure stiffening, and it maintains the analytical convenience of a standard bear eigensolution once the stiffness has been modified. Demonstration of the approach is accomplished through the creation and test verification of an inflated cylinder model using a large commercial finite element code. Good frequency and mode shape comparisons are obtained with test data and previous modeling efforts, verifying the accuracy of the technique. Problems encountered in the application of the approach, as well as their solutions, are discussed in detail.

Smalley, Kurt B.↗

Structural Model Tuning Capability in an Object-Oriented Multidisciplinary Design, Analysis, and Optimization Tool

Updating the finite element model using measured data is a challenging problem in the area of structural dynamics. The model updating process requires not only satisfactory correlations between analytical and experimental results, but also the retention of dynamic properties of structures. Accurate rigid body dynamics are important for flight control system design and aeroelastic trim analysis. Minimizing the difference between analytical and experimental results is a type of optimization problem. In this research, a multidisciplinary design, analysis, and optimization [MDAO] tool is introduced to optimize the objective function and constraints such that the mass properties, the natural frequencies, and the mode shapes are matched to the target data as well as the mass matrix being orthogonalized.

Lung, Shun-fat↗

Structural Model Tuning Capability in an Object-Oriented Multidisciplinary Design, Analysis, and Optimization Tool

Updating the finite element model using measured data is a challenging problem in the area of structural dynamics. The model updating process requires not only satisfactory correlations between analytical and experimental results, but also the retention of dynamic properties of structures. Accurate rigid body dynamics are important for flight control system design and aeroelastic trim analysis. Minimizing the difference between analytical and experimental results is a type of optimization problem. In this research, a multidisciplinary design, analysis, and optimization (MDAO) tool is introduced to optimize the objective function and constraints such that the mass properties, the natural frequencies, and the mode shapes are matched to the target data as well as the mass matrix being orthogonalized.

Lung, Shun-fat↗

Objectives and Progress on Ground Vibration Testing for the Ares Launch Vehicles

NASA has conducted dynamic tests on each of its major launch vehicles during the past 45 years. Each test has provided invaluable data to correlate and correct analytical models used to predict structural responses to differing dynamics for these vehicles. With both Saturn V and Space Shuttle, hardware changes were also required to the flight vehicles to ensure crew and vehicle safety. The Ares I IVGVT will undoubtedly provide similar valuable test data to support successful flights of the Constellation Program. The IVGVT will provide test determined natural frequencies, mode shapes and damping for the Ares I. This data will be used to support controls analysis by providing this test data to reduce uncertainty in the models. The value of this testing has been proven by past launch vehicle successes and failures. Performing dynamic testing on the Ares vehicles will provide confidence that the launch vehicles will be safe and successful in their missions. In addition, IVGVT will provide the following benefits for the Ares rockets: a) IVGVT data along with Ares development flights like Ares I-X, Ares I-Y, Ares I-X Prime, and Orion-1 or others will reduce the risk to the Orion-2 crew. IVGVT will permit anchoring the various analytical and operational models used in so many different aspects of Ares operations. b) IVGVT data will permit better understanding of the structural and GN&C margins of the spacecraft and may permit mass savings or expanded day-of-launch opportunities or fewer constraints to launch. c) Undoubtedly IVGVT will uncover some of the "unknown unknowns" so often seen in developing, launching, and flying new spacecraft vehicles and data from IVGVT may help prevent a loss of vehicle or crew. d) IVGVT also will be the first time Ares I flight-like hardware is transported, handled, rotated, mated, stacked, and integrated. e) Furthermore, handling and stacking the IVGVT launch vehicle stacks will be an opportunity to understand certain aspects of vehicle operability much better (for example, handling procedures, touch-labor time to accomplish tasks, access at interfaces, access to stage mating bolts, access to avionics boxes, access to the Interstage, GSE functionality, and many other important aspects of Ares I operability). All of these results will provide for better vehicle safety and better stewardship of national resources as NASA begins its next phase of human space exploration.

Tuma, Margaret L.↗

Quantitative models of magnetic and electric fields in the magnetosphere

In order to represent the magnetic field B in the magnetosphere various auxiliary functions can be used: the current density, the scalar potential, toroidal and poloidal potentials, and Euler potentials -- or else, the components of B may be expanded directly. The most versatile among the linear representations is the one based on toroidal and poloidal potentials; it has seen relatively little use in the past but appears to be the most promising one for future work. Other classifications of models include simple testbed models vs. comprehensive ones and analytical vs. numerical representations. The electric field E in the magnetosphere is generally assumed to vary only slowly and to be orthogonal to B, allowing the use of a scalar potential which may be deduced from observations in the ionosphere, from the shape of the plasmapause, or from particle observations in synchronous orbits.

Stern, D. P.↗

Frequency domain solutions to multi-degree-of-freedom, dry friction damped systems under periodic excitation

The anticipated low damping level in large space structures (LSS) has been a major concern for the designers of these structures. Low damping degrades the free response and complicates the design of shape and attitude controllers for flexible spacecraft. Dry friction damping has been considered as a means of increasing the passive damping of LSS, by placing it in the joints and connecting junctures of structures. However, dry friction is highly nonlinear and, hence, analytical investigations are difficult to perform. Here, a multi-harmonic, frequency domain solution technique is developed and applied to a multi-DOF, dry friction damped system. It is seen that the multi-harmonic method is much more accurate than traditional, one harmonic solution methods. The method also compares well with time integration. Finally, comparisons are made with experimental results.

Ferri, A. A.↗

Large-Scale Advanced Prop-Fan (LAP) blade design

This report covers the design analysis of a very thin, highly swept, propeller blade to be used in the Large-Scale Advanced Prop-Fan (LAP) test program. The report includes: design requirements and goals, a description of the blade configuration which meets requirements, a description of the analytical methods utilized/developed to demonstrate compliance with the requirements, and the results of these analyses. The methods described include: finite element modeling, predicted aerodynamic loads and their application to the blade, steady state and vibratory response analyses, blade resonant frequencies and mode shapes, bird impact analysis, and predictions of stalled and unstalled flutter phenomena. Summarized results include deflections, retention loads, stress/strength comparisons, foreign object damage resistance, resonant frequencies and critical speed margins, resonant vibratory mode shapes, calculated boundaries of stalled and unstalled flutter, and aerodynamic and acoustic performance calculations.

Violette, John A.↗

Buoyancy effects of a growing, isolated dendrite

The buoyancy effect of a growing isolated dendrite on the solidification process in the undercooling liquid material was investigated by developing an analytic solution to the growth/convection problem in powers of a buoyancy parameter G. The solution depends on the Prandtl number P and the Stefan number S (undercooling) for the local velocity and thermal fields and also the buoyant alteration of the interface shape. Results suggest that buoyancy effect for metals (low P) may be qualitatively different from that for organics (high P).

Canright, D.↗

Constitutive Equations: Plastic and Viscoelastic Properties. (Latest citations from the Aerospace Database)

The bibliography contains citations concerning analytical techniques using constitutive equations, applied to materials under stress. The properties explored with these techniques include viscoelasticity, thermoelasticity, and plasticity. While many of the references are general as to material type, most refer to specific metals or composites, or to specific shapes, such as flat plate or spherical vessels.

VISCOELASTICITY↗

Constitutive Equations: Plastic and Viscoelastic Properties. (Latest Citations from the Aerospace Database)

The bibliography contains citations concerning analytical techniques using constitutive equations, applied to materials under stress. The properties explored with these techniques include viscoelasticity, thermoelasticity, and plasticity. While many of the references are general as to material type, most refer to specific metals or composites, or to specific shapes, such as flat plate or spherical vessels. (Contains 50-250 citations and includes a subject term index and title list.)

BIBLIOGRAPHIES↗