Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “progress report”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

MagMicro with Ultra-High Energy Resolution (Progress Report Q4 FY18)

We are performing extensive simulations of the MMC detector response to optimize their energy resolution, detection efficiency and count rate based on the data we took in FY17/18. The optimized layout separates the MMC detector chip from the SQUID preamplifier chips coupled to the MMCs through Al wire bonds to avoid heating the MMC with the power dissipation of the SQUID. The goal is to design MMC gamma detectors with a limiting energy resolution below ~25 eV FWHM up to >100 keV and ~1 ms decay times for maximum count rates of several tens of counts/s per pixel. The simulations, which were done at the Supercomputing Center of the University of New Mexico, are taking significantly longer than expected. The difficulty is that the device performance depends intricately on the design parameters, and each simulation is quite involved because it needs to cover the frequency range well into the GHz range to account for the ac Josephson effect. This is delaying the start of the detector array fabrication, and we have not been able to complete the fabrication and the testing of the 32-pixel MMC arrays by September 30. We have therefore requested a no-cost extension of the project to March 31, 2019.

42 ENGINEERING↗

Progress Report on Modified Burst Testing and Alternative Test Methodologies

Performance of accident-tolerant fuel candidates must be assessed during the pellet-cladding mechanical interaction (PCMI) phase of a design-basis reactivity-initiated accident (RIA). Therefore, in this report, we describe Fiscal Year (FY) 2019 research activities on the development of separate-effects testing for ATF cladding candidate iron-chromium-aluminum (FeCrAl) tube specimens under loading conditions comparable to the PCMI. The first section of this report provides modified-burst test (MBT) results of unirradiated FeCrAl tubes at various pressurization-rates and an RIA-relevant temperature (275°C). The failure strain of FeCrAl was observed and calculated using a high-speed digital-image correlation (DIC) technique developed recently under the Department of Energy (DOE)’s Advanced Fuel Campaign (AFC). To overcome the complexities of performing MBT in a hot-cell environment on irradiated samples, a “plane-strain tension” (PST) test was proposed as an alternative methodology for PCMI testing. The relevance of the PST test as an alternative to MBT for irradiated specimens was explicated using the data available in the literature. The design of hot-cell compatible PST fixtures and a specific holder for PST hot-cell specimen machining were developed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improving Fission Products at CARIBU: Near Field Detection (Q3/FY19 Quarterly Progress Report)

In the last quarter, Miguel Bencomo joined our group as a postdoc. Miguel got his PhD degree from Texas A&M University last December, where he was working on precision beta decay measurements, using techniques similar to the approach we use to measure branching ratios. We have been training him on how to use our analysis and simulation tools, as well as bringing him up to speed on the technical details of our experiment. The analysis and writing the manuscript for 95 Zr has been completed and are waiting for a feedback from Texas A&M collaborators. This process has been slightly delayed due to vacations and their obligations to other experiments at Texas A&M. We have begun working with Benjamin Schroeder (PhD student from Texas A&M), he is currently learning our analysis tools and looking at decay data of 95 Zr. Ben has just finalized his Master thesis and is very well positioned to start working with us, by first learning our analysis technique on 95 Zr proof-of-principle data, and next be responsible for analysis 156 Eu data that we plan to take later this year.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Gamma-ray Mirrors (Quarterly Progress Report Q2 FY2019)

Our main activity this quarter was focused on carrying out the experimental campaign with our mirror system at the Irradiated Fuel Examination Laboratory (IFEL) at ORNL. The experimental campaign took place from January 22 to February 7, 2019.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

The Quantum Nature and Mass of the Neutrino: FY19 Annual Laboratory Continuation Progress Report

Over the last 100 years we have learned a much about the neutrino, but there remain interesting questions about this weakly interacting particle. In particular, at LLNL we are developing experiments to measure short baseline oscillation, the mass and the quantum nature of the neutrino, the latter two are within the scope of DOE-SC NP and are the subject of this report. The 2015 long range plan recommended tonne-scale neutrinoless double beta decay experiments as the top new project priority and this experiment will target the quantum nature of the neutrino. The LLNL team is motivated and focused on developing the best technology for this experiment which is a liquid xenon time project chamber called nEXO. On a longer time scale, LLNL is also developing technology to measure the neutrino mass with tritium decay experiments.

42 ENGINEERING↗

Progress Report on the Investigation of Separable Floating Layers in Hanford Double-Shell Tank Supernates

A review of studies performed the last four years at 222-S Laboratory on separable floating solids including demonstration of the formation of a floating layer in the organic-bound simulated solids and investigation of floating solids found in AN-101 and AW-104 as well as carbonate precipitation floating on the surface of AN-107 grab samples. Demonstrated that semivolatile organic analysis can detect separable organics including tributyl phosphate, degradation products of Quintolubric hydraulic fluid, and hydrocarbon as tentatively identified compounds. In addition, an evaluation of the relationship of small organic acids to the total organic carbon is discussed in selected double-shell tank supernate. A systematic approach is presented to monitor separable organics and insoluble particulates in the double-shell tank waste.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Kelvin Probe Force Microscopy for High-Resolution Imaging of Hydrogen in Steel and Aluminum Alloys (Q3 Progress Report)

SRNL is working with Sandia NL, Pacific Northwest NL and Oak Ridge NL in the H-Mat consortium with the objective of developing materials with a higher resistance to hydrogen attack. Understanding the mechanism of hydrogen interactions in metal alloys is continually a topic of interest for applications which involve the long-term storage of hydrogen. Atomic hydrogen segregates to regions of extended defects, such as grain and phase boundaries, and can cause stress and premature cracking through a process known as hydrogen embrittlement. Advanced microstructural imaging techniques, with minimal sample preparation needs, that are capable of resolving hydrogen segregation at the nanometer scale is needed. Current imaging technologies to aid in understanding the effects of hydrogen in metals involve primarily fractography after mechanical testing. Hydrogen segregated at the surface and particularly at surface defect sites changes the local work function of the material. This can be measured by Kelvin Probe Force Microscopy, KPFM, a variant of atomic force microscopy (AFM). KPFM produces surface potential images and is capable of measuring the local change in work function of surfaces with very high spatial resolution. The spatial resolution of KPFM is optimally ~5 nm, yielding very high hydrogen concentration/microstructure coloration capabilities. By locating the presence of hydrogen and its relationship with extended defects, it may be possible to develop microstructures less susceptible to hydrogen embrittlement. The objective of this effort is to assess the utility of KPFM to determine the H 2 concentration profiles surrounding complex microstructural features in high strength steel and aluminum alloys subjected to high pressure hydrogen exposure.

08 HYDROGEN↗

MagMicro with Ultra-High Energy Resolution (FY19 Q3 Progress Report)

The fabrication of the MMC detector arrays involves two photolithographic procedures. The first is to fabricate the Nb magnetization coil and pick-up coils, the SQUID preamplifiers and the associated wiring. This is done on a full 4” Si wafer, which is subsequently diced into ~0.5 cm2 SQUID chips and ~1 cm2 detector chips. The detector chips are then processed separately by depositing and patterning the paramagnetic Ag:Er sensor and support structures and then electroplating the Au absorber. In Q3, we have successfully completed the full wafer processing for the 32-pixel MMC detector arrays, diced the 4” wafer into the smaller chips and tested the individual components. The coils have the required critical current, the heat switches have a critical temperature in the desired range, and the SQUIDs have the required low noise. Unfortunately, the sputter deposition of the paramagnetic Ag:Er sensor failed several times. We spent considerable time to trace the problem to contaminations of the purifier for the Ar sputtering gas that had been exposed to atmosphere for an extended time during an earlier clean room upgrade. We then determined that the purifier is not essential for high-quality Ag:Er sensor films (Fig. 1), and successfully deposited the Ag:Er sensor film on the ~1 cm 2 detector chip.

42 ENGINEERING↗

Quarterly Progress Report Q3 FY2019 Apr-Jun 2019

Our main activity this quarter was focused on carrying out the data analysis following the experimental campaign conducted at the Irradiated Fuel Examination Laboratory (IFEL) at ORNL. More specifically, we focused on the demonstration of hard X-rays two reflections, as well as the quantification of the background reduction and signal-to-noise-ratio (SNR) under different experimental conditions. Significant time and effort was spent developing data analysis tools using the Root software toolkit, and carefully checking data consistency across data sets and with simulations. Some results are presented below.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Wood-to-Fuel for California's Transportation Sector using Autothermal Pyrolysis (Progress Report)

We sent our updated draft Site License Agreement back to SPI on June 4 th , with redlines. Gary Blanc of SPI said he would circulate it internally to appropriate parties and get back to us. He did not return an accepted or redlined version to us before the end of the month of July, nor did he send us any questions/comments or updates, despite them being requested. He is currently traveling around visiting SPI’s various forestry locations and mills, so is difficult to reach. In working towards the commercialization strategy, during the month of July, further research was completed on understanding and evaluating the availability and potential availability of fire clearing forestry residue in California. In July, a meeting with Stephen Kaffka and Rob Williams who are both authors of the report “An Assessment of Biomass Resource in California, 2013” was attended. These individuals provided us with guidance and information about how to identify the availability and potential availability of forestry/wood resource biomass in California. Also, in the month of July, a meeting with Cal-Fire was attended in order to understand what Cal-Fire plans to do in terms of reducing the risk of wildfires and how much potential fire clearing forestry residue biomass this will produce for California. Additionally, the potential of a novel pathway of producing H2 from pyrolysis oil, maximizing the products’ value, as well as maximizing the carbon emission reduction potential by incorporating carbon capture onsite, was investigated. We continued with the process of subcontracting with Iowa State University and Frontline BioEnergy. We have our Contract Administrators working with their counterparts at each partner to get the details in place. Draft contracts with statements of work were provided to each partner, and updated schedules and budgets, broken down by task in the statements of work, have been requested from each.

09 BIOMASS FUELS↗

Progress Report on An Exascale Computational Simulation Capability for Pervasive Fracture & Failure

How does a structure fail in an explosion? Is there an engineering design opportunity to mitigate the effects of a blast? These are questions that may be addressed with simulation; however, a computational simulation capability to answer these questions must include developments in material physics modeling and numerical algorithms that we believe are possible, but do not yet exist. This LDRD project proposes to develop the physics models and computational approaches to create a computational simulation approach to answer these physics and engineering questions.

42 ENGINEERING↗

Automated Particle Classifier (Quarterly Progress Report Q4 FY19)

This is the fourth quarter of reporting for an extension after the final year of this project. Work during this quarter included developing a relationship with UK AWE in anticipation of advising and supporting the development of a fast neutron detector for UK MOD.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Hydrogen Quantitative Risk Assessment (Annual Progress Report)

DOE has identified consistent safety, codes, and standards as a critical need for the deployment of hydrogen technologies, with key barriers related to the availability and implementation of technical information in the development of regulations, codes, and standards. Advances in codes and standards have been enabled by risk-informed approaches to create and implement revisions to codes, such as National Fire Protection Association (NFPA) 2, NFPA 55, and International Organization for Standardization (ISO) Technical Specification (TS)-19880-1. This project provides the technical basis for these revisions, enabling the assessment of the safety of hydrogen fuel cell systems and infrastructure using QRA and physics-based models of hydrogen behavior. The risk and behavior tools that are developed in this project are motivated by, shared directly with, and used by the committees revising relevant codes and standards, thus forming the scientific basis to ensure that code requirements are consistent, logical, and defensible.

08 HYDROGEN↗

Gamma mirrors Quarterly Progress Report Y1Q4 FY2019

During the fourth quarter of FY19, we completed task 1.2 of Phase 1, the data analysis of the experimental campaign conducted at the Irradiated Fuel Examination Laboratory (IFEL) at ORNL. The best part of the analysis was conducted during the third quarter and the relevant findings can be found in the FY19 Q3 report. Phase II of the project was started during the month of September, more specifically Task 2. All experiments so far were conducted with ultrasmooth flat optics with a periodic multilayer coating with reflectivity of >80% in the 100 keV range. We have been determining the best available simulation tools to model X-ray focusing optics, typically made of quadratic surfaces, in order to survey the relevant parameter space and conduct the design study. Candidate focusing optics designs are Wolter I optics, Kirkpatrick-Baez or KB optics and Schmidt optics. Informed by the IFEL results, we are also considering a single-reflection concentrator design to attempt to quantify possible trade-off between bandpass multilayers overall reflectivity, multiple reflections and energy selectivity.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Improving Fission Products at CARIBU: Near Field Detection (Q4/FY19 Quarterly Progress Report)

We have been having ongoing discussions about the analysis and the text of the 95 Zr manuscript with our collaborators at Texas A&M University (TAMU). K. Kolos has travelled to Texas to discuss, once again, some details of our GEANT4 simulation used to determine the gas-counter efficiency. In that process, we discovered that there was a slight disagreement (~0.5%) between our results and the results obtained with the EGS code used by the TAMU group. We are currently working to determine and magnitude and source of the discrepancy. This has taken a considerable amount of time and, unfortunately, has hindered us from sending out the paper to all of our collaborators. We also recently found out that Benjamin Schroeder, the Texas A&M student supported by the CENTUAR Center of Excellence who joined our project earlier this year, has decided to leave graduate school after obtaining his Master Thesis. Although this is a loss for our team, we do not foresee this to cause a major disruption in the project. Our TAMU collaborators are still committed to the success of these measurements.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗