Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polycrystalline material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Micro-cantilever beam experiments and modeling in porous polycrystalline UO 2

Understanding the impact of microstructure on the thermo-mechanical behavior of oxide nuclear fuels is vital to predicting their performance through multiscale models. Evaluating the mechanical properties at the sub-grain length scale is key to developing these multiscale models. In this work, 3D finite element (FE) models were constructed to simulate the micrometer-scale bending of micro-cantilever beams fabricated using porous polycrystalline uranium dioxide (UO 2 ) and tested at room temperature. Here, the results showed that the porosity and elastic anisotropy of individual grains can play a significant role in determining the effective mechanical properties of the material deduced from the tests. Specifically, the porosity had a non-negligible effect, given that the pore size was of the same order of magnitude as the dimensions of the micro-beams. Correlations between load-deflection data, pore location, and elastic properties (effective Young's modulus) were investigated using UO 2 micro-beam FE models, where pore clusters were included and placed at different locations along the length of the beam. Results indicated that the presence of pore clusters near the substrate, i.e., the clamp of the micro-cantilever beam, has the strongest effect on the load-deflection behavior, with the porosity leading to a reduction of stiffness that is the largest for any location of the pore clusters. Furthermore, it was also found that pore clusters located towards the middle of the span and close to the end of the beam have a comparatively small effect on the load-deflection behavior. Therefore, it is concluded that accurate estimates of Young's modulus can be obtained from micro-cantilever experiments after accounting for porosity on the one third of the beam length close to the clamp. This, in turn, provides an avenue to improve microscale experiments and their analysis in porous, anisotropic elastic materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Triplet Excitons in Pentacene Are Intrinsically Difficult to Dissociate via Charge Transfer

Singlet fission (SF) has the potential to bypass the Shockley–Queisser limit for solar cell efficiency through the production of two electron–hole pairs per photon. However, in polycrystalline pentacene this goal is hindered by slow charge transfer from triplets (=10 7 s –1 ) after SF. In this paper we demonstrate that slow charge transfer is an intrinsic property of triplet states in this material and most likely not connected with the triplet pair states that may result from singlet fission. We compare two perylene diimide/pentacene charge transfer systems that differ only by triplet generation mechanism: SF versus intersystem crossing (ISC), sensitized by using a soluble lead phthalocyanine derivative. We use time-resolved microwave conductivity (TRMC) to measure the charge yield in each system and transient absorption (TA) to follow the triplet population dynamics. These experiments are described by a single global kinetic model, with most of its parameters fixed via control experiments. While we observe modest differences in the charge-transfer rate constants between each sample, 4–10× as a function of triplet generation mechanism, all samples remain far below the predicted diffusion-limited rate constant of 10 7 –10 8 s –1 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Epitaxial Stabilization and Oxygen Evolution Reaction Activity of Metastable Columbite Iridium Oxide

Non-rutile polymorphs of binary iridium oxide such as columbite IrO 2 (α-IrO 2 ) are promising candidates for highly active acid-stable oxygen evolution reaction (OER) catalysts, yet their synthesis has been challenging due to the dominant thermodynamic stability of rutile IrO 2 (R-IrO 2 ). Here, we report the growth of α-IrO 2 via epitaxial thin films using pulsed laser deposition. We observe that, in competition with R-IrO 2 (100), the films can be optimized to be predominantly (100)-oriented α-IrO 2 . Surprisingly, the activity of α-IrO 2 shows a large discrepancy of ~0.2 V in the overpotential compared to its predicted activity, which is resolved via theoretical calculations to be a crystal orientation effect. This demonstrates that the electrocatalytic activity can be significantly varied upon crystal orientation, a parameter that is difficult to control in conventional polycrystalline systems but accessible in epitaxial thin films. In total, this study demonstrates epitaxial thin film growth as a powerful technique, which can overcome large energetic instabilities on the order of ~300 meV to stabilize metastable material structures inaccessible by bulk synthesis. As a result, this provides unique opportunities to effectively identify the atomic structure of active catalysts by combining investigations of metastable materials with theoretical predictions.

36 MATERIALS SCIENCE↗
NASA NTRS2000

Process to produce silicon carbide fibers using a controlled concentration of boron oxide vapor

A process for producing polycrystalline silicon carbide includes heating an amorphous ceramic fiber that contains silicon and carbon in an environment containing boron oxide vapor. The boron oxide vapor is produced in situ by the reaction of a boron containing material such as boron carbide and an oxidizing agent such as carbon dioxide, and the amount of boron oxide vapor can be controlled by varying the amount and rate of addition of the oxidizing agent.

Barnard, Thomas Duncan↗
NASA NTRS2001

Process to produce silicon carbide fibers using a controlled concentration of boron oxide vapor

A process for producing polycrystalline silicon carbide by heating an amorphous ceramic fiber that contains silicon and carbon in an environment containing boron oxide vapor. The boron oxide vapor is produced in situ by the reaction of a boron containing material such as boron carbide and an oxidizing agent such as carbon dioxide, and the amount of boron oxide vapor can be controlled by varying the amount and rate of addition of the oxidizing agent.

Barnard, Thomas Duncan↗
DOE OSTI2023

Bipolar transistor structure with collector on polycrystalline isolation layer and methods to form same

Embodiments of the disclosure provide a bipolar transistor structure with a collector on a polycrystalline isolation layer. A polycrystalline isolation layer may be on a substrate, and a collector layer may be on the polycrystalline isolation layer. The collector layer has a first doping type and includes a polycrystalline semiconductor. A base layer is on the collector layer and has a second doping type opposite the first doping type. An emitter layer is on the base layer and has the first doping type. A material composition of the doped collector region is different from a material composition of the base layer.

Holt, Judson R.↗
DOE OSTI2021

Atomistic Assessment of Solute-Solute Interactions during Grain Boundary Segregation

Grain boundary solute segregation is becoming increasingly common as a means of stabilizing nanocrystalline alloys. Thermodynamic models for grain boundary segregation have recently revealed the need for spectral information, i.e., the full distribution of environments available at the grain boundary during segregation, in order to capture the essential physics of the problem for complex systems like nanocrystalline materials. However, there has been only one proposed method of extending spectral segregation models beyond the dilute limit, and it is based on simple, fitted parameters that are not atomistically informed. In this work, we present a physically motived atomistic method to measure the full distribution of solute-solute interaction energies at the grain boundaries in a polycrystalline environment. We then cast the results into a simple thermodynamic model, analyze the Al(Mg) system as a case study, and demonstrate strong agreement with physically rigorous hybrid Monte Carlo/molecular statics simulations. This approach provides a means of rapidly measuring key interactions for non-dilute grain boundary segregation for any system with an interatomic potential.

36 MATERIALS SCIENCE↗
NASA NTRS2016

Dynamic Characterization of Galfenol (Fe81.6Ga18.4)

Galfenol has the potential to transform the smart materials industry by allowing for the development of multifunctional, load-bearing devices. One of the primary technical challenges faced by this development is the very limited experimental data on Galfenol's frequency-dependent response to dynamic stress, which is critically important for the design of such devices. This report details a novel and precise characterization of the constitutive behavior of polycrystalline Galfenol (Fe81.6Ga18.4) under quasi-static (1 Hz) and dynamic (4 to 1000 Hz) stress loadings. Mechanical loads are applied using a high-frequency load frame. Quasi-static minor and major hysteresis loop measurements of magnetic flux density and strain are presented for constant electromagnet currents (0 to 1.1 A) and constant magnetic fields 0 to 14 kA/m (0 to 180 Oe). The dynamic stress amplitude for minor and major loops is 2.88 and 31.4 MPa (418 and 4550 psi), respectively. Quasi-static material properties closely match published values for similar Galfenol materials. Quasi-static actuation responses are also measured and compared to quasi-static sensing responses; the high degree of reversibility seen in the comparison is consistent with published measurements and modeling results. Dynamic major and minor loops are measured for dynamic stresses up to 31 MPa (4496 psi) and 1 kHz, and the bias condition resulting in maximum, quasi-static sensitivity. Eddy current effects are quantified by considering solid and laminated Galfenol rods. Three key sources of error in the dynamic measurements are accounted for: (1) electromagnetic noise in strain signals due to Galfenol's magnetic response, (2) error in load signals due to the inertial force of fixturing, and (3) phase misalignment between signals due to conditioning electronics. For dynamic characterization, strain error is kept below 1.2 percent of full scale by wiring two collocated gauges in series (noise cancellation) and through leadwire weaving. Inertial force error is kept below 0.41 percent by measuring the dynamic force in the specimen using a nearly collocated piezoelectric load washer. The phase response of all conditioning electronics is explicitly measured and corrected for. In general, as frequency is increased, the sensing response becomes more linear because of an increase in eddy currents. As frequency increases above approximately 100 Hz, the elbow in the strain-versus-stress response disappears as the active (soft) regime stiffens toward the passive (hard) regime. Under constant-field conditions, the loss factors of the solid rod peak between 200 and 600 Hz, rather than exhibiting a monotonic increase. Compared to the solid rod, the laminated rod exhibits much slower increases in hysteresis with frequency, and its quasi-static behavior extends to higher frequencies. The elastic modulus of the laminated rod decreases between 100 and 300 Hz; this trend is currently unexplained.

Dynamic sensing↗
NASA NTRS2005

Synthesis, Characterization and Decomposition Studies of Tris(N,N-dibenzyldithiocarbamato) Indium(III): Chemical Spray Deposition of Polycrystalline CuInS2 on Copper Films

Tris(bis(phenylmethyl)carbamodithioato-S,S ), commonly referred to as tris(N,Ndibenzyldithiocarbamato) indium(III), In(S2CNBz2)3, was synthesized and characterized by single crystal X-ray crystallography. The compound crystallizes in the triclinic space group P1 bar with two molecules per unit cell. The material was further characterized using a novel analytical system employing the combined powers of thermogravimetric analysis, gas chromatography/mass spectrometry and Fourier-Transform infrared spectroscopy to investigate its potential use as a precursor for the chemical vapor deposition (CVD) of thin film materials for photovoltaic applications. Upon heating, the material thermally decomposes to release CS2 and benzyl moieties in to the gas phase, resulting in bulk In2S3. Preliminary spray CVD experiments indicate that In(S2CNBz2)3 decomposed on a Cu substrate reacts to produce stoichiometric CuInS2 films.

Hehemann, David G.↗
DOE OSTI2020

Vacancy and interstitial interactions with crystal/amorphous, metal/covalent interfaces

In this work, we use atomistic simulations to investigate the interaction of vacancies and interstitials with interfaces between a crystalline metal and an amorphous, covalently-bonded solid. We select the gold (Au)/silicon (Si) binary system as a model material and construct interface models along two different facets of crystalline Au and with amorphous Si (a-Si) created at three different quench rates. We compute formation energies of vacancies, self-interstitials, and interstitial impurities as a function of position relative to the interface and find that they have markedly lower values near the interface than in the interior of the adjoining phases. We conclude that crystal/amorphous, metal/covalent interfaces may be as effective at removing radiation-induced point defects as interfaces in polycrystalline metals composites. Moreover, irrespective of interface character, the average formation energies of all point defects at all the Au/a-Si interfaces we investigated are comparable. Thus, unlike in polycrystalline metals, where an interface’s crystallographic character has a marked effect on its interactions with point defects, all interface types in crystal/amorphous, metal/covalent composites may be equally effective at absorbing all radiation-induced defects.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ X-ray measurements over large Q-space to study the evolution of oxide thin films prepared by RF sputter deposition

Sputter deposition is a versatile and industrially important deposition technique for thin films, with increasing demand for matching the characteristics of thin film materials to specific requirements. Additionally, the actual film properties are largely determined by sputtering parameters such as pressure conditions, temperature and power settings. By means of various X-ray diffraction and scattering techniques, it is shown that the characterization of film formation and growth is feasible in real time at synchrotron sources, thus adding an important dimension to the fundamental understanding of the evolution of thin film microstructure. In particular, grazing incidence small-angle X-ray scattering, grazing incidence X-ray powder diffraction and X-ray reflectometry are used in a complementary manner to study the influence of deposition temperature and substrate choice on the crystallization kinetics and growth of polycrystalline BaTiO 3 films.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hydrogen and deuterium permeation in Hastelloy N

Hastelloy N was chosen as the fluoride salt-contacting structural material for the Molten Salt Reactor Experiment due to its excellent compatibility with the fuel salt FLiBe. FLiBe is currently investigated for several advanced fusion and fission reactor concepts where tritium generation in the FLiBe is anticipated. Knowledge of hydrogen transport properties through Hastelloy N is important to understand how tritium would permeate through this material and result in an unintentional release. In this study, the hydrogen and deuterium permeability, diffusivity, and solubility were measured from 500 to 700 °C at a primary-side pressure of 10 kPa in a well-characterized sample of Hastelloy N. The prepared polycrystalline Hastelloy N had C and O impurities present on the surface. These impurities were investigated using Auger Emission Spectroscopy and Ar depth profiling. Here, the adventitious C was removed upon the first Ar sputter cycle whereas O persisted deeper into the sample. For permeation experiments, applied deuterium pressures ranged from 13 Pa to 100 kPa and deuterium transport remained in the diffusion-limited regime (J ∝ P 0.5 ) throughout the pressure range examined. Two methods are employed to measure the effective hydrogen and deuterium diffusivity: rise and decline. The decline method produced improved statistical model fits for calculating the effective diffusion coefficient compared to the rise method. The resultant transport properties compared well to published values for other nickel alloys.

08 HYDROGEN↗
DOE OSTI2022

Measurement of grain boundary strength of Inconel X-750 superalloy using in-situ micro-tensile testing techniques in FIB/SEM system

Grain boundaries (GBs), known as two-dimensional defects, are omnipresent in polycrystalline metallic alloys and thus influence a wide range of mechanical properties under different environmental conditions like irradiation and corrosion. Therefore, quantifying the strength of individual GBs is critical for understanding the degradation of mechanical properties of materials under different conditions. In this study we developed an efficient approach for the fabrication of micro-tensile specimens with a GB almost perpendicular to the tensile direction, which is expected to advance the development of individual GB tensile testing at micro or nanoscale in a wide scope of materials. Further, an in-situ cantilever micro-tensile testing method was developed and used to quantify the strength of a Σ3 GB in Inconel X-750 with the combination of finite element modeling. The average ultimate tensile strength (UTS) of a non-irradiated Σ3 GB is estimated at around 1.4 GPa, comparable to that of a neutron-irradiated Σ3 GB with a dose of ~1.5 dpa (1.3 GPa). Moreover, the in-situ push-to-pull micro-tensile testing technique developed in this work provides valuable insights into the high-angle GB deformation and fracture behavior. This method generates qualitatively similar ductility behavior before and after neutron irradiation as the bulk material testing. However, the ductility and UTS values obtained from this method are different from bulk measurements due to vastly different specimen dimensions.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Experimental shock metamorphism of mono- and polycrystalline olivine - A comparative study

The paper reports on a series of controlled shock recovery experiments which have been performed on over 40 samples including monocrystalline, polycrystalline, dunite, and porous particulate olivine-bearing targets. Results of the mineralogical and petrological analyses of these samples are used to establish a general and comparative diagnosis of shock effects generated in various olivine-bearing materials. Finally, some experiments are conducted under different ambient pO2 conditions so that information on the distribution of observed impact features is derived as a function not only of peak pressure and texture of the target sample, but also of specific environmental conditions.

Bauer, J. F.↗
NASA NTRS1982

Optimization of solar cells for air mass zero operation and a study of solar cells at high temperatures

The power to weight ratio of GaAs cells can be reduced by fabricating devices using thin GaAs films on low density substrate materials (silicon, glass, plastics). A graphoepitaxy technique was developed which uses fine geometric patterns in the substrate to affect growth. Initial substrates were processed by etching 25 microns deep grooves into 100 oriented wafers; fine-grained polycrystalline GaAs layers 25-50 microns thick were then deposited on these and recrystallization was performed, heating the substrates to above the GaAs melting point in ASH3 atmosphere, resulting in large grain regrowth oriented along the groove dimensions. Experiments with smaller groove depths and spacings were initially encouraging; single large GaAs grains would totally cover one and often two groove fields of 14 groove each spanning several hundred microns. Dielectric coatings on the grooved substrates were also used to modify the growth.

Hovel, H. J.↗
NASA NTRS1989

Advances in thin-film solar cells for lightweight space photovoltaic power

The development of photovoltaic arrays beyond the next generation is discussed with attention given to the potentials of thin-film polycrystalline and amorphous cells. Of particular importance is the efficiency (the fraction of incident solar energy converted to electricity) and specific power (power to weight ratio). It is found that the radiation tolerance of thin-film materials is far greater than that of single crystal materials. CuInSe2 shows no degradation when exposed to 1-MeV electrons.

Landis, Geoffrey A.↗