Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “modules”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Potential-Induced Degradation-Delamination Mode in Crystalline Silicon Modules: Preprint

A test sequence producing potential-induced degradation-delamination (PID-d) in crystalline silicon modules has been tested and found comparable under visual inspection to cell/encapsulant delamination seen in some fielded modules. Four commercial modules were put through this sequence, 85 degrees C, 85%, 1000 h damp heat, followed by an intensive PID stress sequence of 72 degrees C, 95% RH, and -1000 V, with the module face grounded using a metal foil. The 60 cell c-Si modules exhibiting the highest current transfer (4.4 center dot 10-4 A) exhibited PID-d at the first inspection after 156 h of PID stress. Effects promoting PID-d are reduced adhesion caused by damp heat, sodium migration further reducing adhesion to the cells, and gaseous products of electrochemical reactions driven by the applied system voltage. A new work item proposal for an IEC test standard to evaluate for PID-d is anticipated.

14 SOLAR ENERGY↗
DOE OSTI2024

PV Modules Temperature Variation and Patterns in Medium and Utility-Scale Floating PV Systems

This paper presents the preliminary results and findings of the four operational Floating PV systems across the USA. At each site, temperature of five PV modules located at North-West, North-East, Middle, South-West, and, South-East have been monitored through the Resistant Temperature Detector (RTD) sensors. Three RTDs were attached to each PV module on the rear-side along the diagonal at top, middle and bottom cells. The preliminary results reveal wide temperature differences among the inter and intra PV modules. Besides this, wave pattern temperatures were observed in a few PV modules. The final results, findings, and, factors responsible will be investigated during the next few months. Index Terms - photovoltaic module, floating PV systems, string, array, temperature, mismatch, utility scale.

ENGINEERING,SOLAR ENERGY↗
DOE OSTI2025

Thermal Optimization and Experimental Demonstration of a Silicon Carbide, Half-Bridge Power Module

This paper describes modeling and experimental work to design and demonstrate a silicon carbide (SiC), single-side-cooled power module. Two SiC metal-oxide-semiconductor field-effect transistors (MOSFET) were used for each switch position and packaged on a metalized ceramic substrate. Thermal modeling was first conducted to optimize the module packaging to minimize junction-to-fluid thermal resistance and device temperature variations. This procedure identified the optimal device placement and baseplate thickness to maximize thermal performance. A heat exchanger - incorporating impinging jets of water-ethylene glycol - was designed to cool the module's baseplate to minimize thermal resistance and pumping power. The heat exchanger used relatively low fluid velocities (<1.5 m/s) to minimize erosion-corrosion effects and relatively large fluid channel sizes (>=1 mm) to prevent clogging. The power module concept was fabricated, and experiments were conducted to measure its thermal performance. Direct current was used to power the module devices, and junction temperatures were measured via device temperature-sensitive parameters. The experimental results were found to be in good agreement with model predictions (within 2%) and yielded junction-to-fluid thermal resistance values as low as about 15 mm2 K/W at relatively low pumping power values. The results demonstrate the improved performance associated with jet impingement cooling and represent an improvement over existing channel-flow-type cold plates, which can enable improvements to power density and reliability.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Tectonic tremor on Vancouver Island, Cascadia, modulated by the body and surface waves of the M w 8.6 and 8.2, 2012 East Indian Ocean earthquakes: Tectonic Tremor on Vancouver Island

The 2012 East Indian Ocean earthquake (M w 8.6), so far the largest intraoceanic plate strike-slip event ever recorded, modulated tectonic tremors in the Cascadia subduction zone. The rate of tremor activity near Vancouver Island increased by about 1.5 times from its background level during the passage of seismic waves of this earthquake. In most cases of dynamic modulation, large-amplitude and long-period surface waves stimulate tremors. However, in this case even the small stress change caused by body waves generated by the 2012 earthquake modulated tremor activity. The tremor modulation continued during the passage of the surface waves, subsequent to which the tremor activity returned to background rates. Similar tremor modulation is observed during the passage of the teleseismic waves from the M w 8.2 event, which occurs about 2 h later near the M w 8.6 event. We show that dynamic stresses from back-to-back large teleseismic events can strongly influence tremor sources.

58 GEOSCIENCES↗
DOE OSTI2018

Hot‐Electron‐Assisted Femtosecond All‐Optical Modulation in Plasmonics

Abstract The optical Kerr nonlinearity of plasmonic metals provides enticing prospects for developing reconfigurable and ultracompact all‐optical modulators. In nanostructured metals, the coherent coupling of light energy to plasmon resonances creates a nonequilibrium electron distribution at an elevated electron temperature that gives rise to significant Kerr optical nonlinearities. Although enhanced nonlinear responses of metals facilitate the realization of efficient modulation devices, the intrinsically slow relaxation dynamics of the photoexcited carriers, primarily governed by electron–phonon interactions, impedes ultrafast all‐optical modulation. Here, femtosecond (≈190 fs) all‐optical modulation in plasmonic systems via the activation of relaxation pathways for hot electrons at the interface of metals and electron acceptor materials, following an on‐resonance excitation of subradiant lattice plasmon modes, is demonstrated. Both the relaxation kinetics and the optical nonlinearity can be actively tuned by leveraging the spectral response of the plasmonic design in the linear regime. The findings offer an opportunity to exploit hot‐electron‐induced nonlinearities for design of self‐contained, ultrafast, and low‐power all‐optical modulators based on plasmonic platforms.

Taghinejad, Mohammad↗
DOE OSTI2023

Solvent‐free Synthesis of Multi‐Module Pore‐Space‐Partitioned Metal‐Organic Frameworks for Gas Separation

Abstract Multi‐module design of framework materials with multiple distinct building blocks has attracted much attention because such materials are more amenable to compositional and geometrical tuning and thus offer more opportunities for property optimization. Few examples are known that use environmentally friendly and cost‐effective solvent‐free method to synthesize such materials. Here, we report the use of solvent‐free method (also modulator‐free) to synthesize a series of multi‐module MOFs with high stability and separation property for C 2 H 2 /CO 2 . The synthesis only requires simple mixing of reactants and short reaction time (2 h). Highly porous and stable materials can be made without any post‐synthetic activation. The success of solvent‐free synthesis of multi‐module MOFs reflects the synergy between different modules, resulting in stable pore‐partitioned materials, despite the fact that other competitive crystallization pathways with simpler framework compositions also exist.

Xiao, Yuchen↗
DOE OSTI2017

Design of photovoltaics for modules with 50% efficiency

Abstract We describe a spectrum splitting solar module design approach using ensembles of 2–20 subcells with bandgaps optimized for the AM 1.5D spectrum. Device physics calculations and experimental data determine radiative efficiency parameters for III ‐V compound semiconductor subcells and enable modification of conventional detailed balance calculations to predict module efficiency while retaining computational speed for a wide search of the design space. Accounting for nonideal absorption and recombination rates due to realistic material imperfections allows us to identify the minimum subcell quantity, quality, electrical connection configuration, and concentration required for 50% module efficiency with realistic optical losses and modeled contact resistance losses. We predict a module efficiency of 50% or greater will be possible with 7–10 electrically independent subcells in a spectral splitting optic at 300–500 suns concentration, assuming a 90% optical efficiency and 98% electrical efficiency, provided the subcells can achieve an average external radiative efficiency of 3–5% and a short circuit current that is at least 90% of the ideal. In examining spectrum splitting solar cells with both series‐connected and electrically independent subcells, we identify a new design trade‐off independent of the challenges of fabricating optimal bandgap combinations. Series‐connected ensembles, having a single set of electrical contacts, are less sensitive to lumped series resistance losses than ensembles where each subcells are contacted independently. By contrast, ensembles with electrically independent subcells can achieve lower radiative losses when the subcells are designed for good optical confinement. Distributing electrically independent subcells in a concentrating receiver module allows flexibility in subcell selection and fabrication, and can achieve ultra‐high efficiency with conventional III ‐V cell technology.

Warmann, Emily C.↗
DOE OSTI2017

From cells to laminate: probing and modeling residual stress evolution in thin silicon photovoltaic modules using synchrotron X-ray micro-diffraction experiments and finite element simulations

Fracture of silicon crystalline solar cells has recently been observed in increasing percentages especially in solar photovoltaic (PV) modules involving thinner silicon solar cells (<200 μm). Many failures due to fracture have been reported from the field because of environmental loading (snow, wind, etc.) as well as mishandling of the solar PV modules (during installation, maintenance, etc.). However, a significantly higher number of failures have also been reported during module encapsulation (lamination) indicating high residual stress in the modules and thus more prone to cell cracking. Here in this paper we report through the use of synchrotron X-ray submicron diffraction coupled with physics-based finite element modeling, the complete residual stress evolution in mono-crystalline silicon solar cells during PV module integration process. For the first time, we unravel the reason for the high stress and cracking of silicon cells near soldered inter-connects. Our experiments revealed a significant increase of residual stress in the silicon cell near the solder joint after lamination. Moreover, our finite element simulations show that this increase of stress during lamination is a result of highly localized bending of the cell near the soldered inter-connects. Further, the synchrotron X-ray submicron diffraction has proven to be a very effective way to quantitatively probe mechanical stress in encapsulated silicon solar cells. Thus, this technique has ultimately enabled these findings leading to the enlightening of the role of soldering and encapsulation processes on the cell residual stress. This model can be further used to suggest methodologies that could lead to lower stress in encapsulated silicon solar cells, which are the subjects of our continued investigations.

14 SOLAR ENERGY↗
DOE OSTI2021

Standards development for modules in high temperature micro-environments

Photovoltaic (PV) module qualification standards, IEC 61215 and IEC 61730, were designed to apply to “general open-air climates” and IEC 61730 specifically indicated applicability of ambient air temperature of 40°C. Additionally, these standards provided allowances for so-called “open rack mounted PV modules” without a clear definition of “open-rack.” These implied restrictions and allowances meant that hotter climates or thermally restrictive installation methods may not be covered by these often customer-mandated certification standards. This is particularly salient for the significant growth regions of the Middle East and India that would be expected to operate at significantly higher temperatures. The applicability of these documents raised issues over the definition of “open rack” and the fact that the geographic location is just as important as the mounting configuration in assessing the impact of the micro-environment of a PV module. This work summarizes the scientific background for IEC Technical Specification 63126:2020 ED1, titled “Guidelines for qualifying PV modules components and materials for operation at high temperatures.” This standard was recently published by the IEC and is the first step in a systematic effort to rework these standards to address the question of temperature more directly. Instead of specifying a mounting condition, we specify different suites of tests suitable for a system (PV module, mounting style, and location) defined by the 98th percentile cell temperature. With a defined temperature regime to work from, this allowed us to use existing literature research combined with additional modeling work to determine, which tests would need to be modified. This resulted in suggested changes to material thermal indices, thermal cycling temperatures, hot spot testing, ultraviolet testing, and bypass diode testing among other tests and characteristics described in this study.

14 SOLAR ENERGY↗
DOE OSTI2022

Future-proofing photovoltaics module reliability through a unifying predictive modeling framework

Solar energy, especially photovoltaics (PV), plays a significant role in the global energy transition required for decarbonization. Technological advancements in increasing efficiencies coupled with cost reductions through economies of scale made PV a cost-competitive energy source set to exceed the milestone of 1 TW globally deployed capacity in 2022. However, ongoing downward price pressure coupled with increasing service life expectations creates tremendous challenges for reliability engineers in ensuring the safe and reliable operation of PV modules and systems over the anticipated service life. Today's reliability research efforts aim for module lifetimes of up to 50 years. Still, our current tools fall short in accurately assessing degradation mechanisms and failure modes over such extended periods. We argue that the well-established PV reliability learning cycle needs to be accelerated to keep up with the rapid technological advancements and high expectations that are put on PV and its role in the global energy transition. In this article, we explore the evolution of the PV reliability learning cycle and highlight the significance that predictive modeling capabilities will have on future PV module reliability. We propose creating a unifying modeling framework - which once established will enable the holistic assessment of PV module reliability, accelerate the PV reliability learning cycle, and bring us closer to quantitative service life predictions of PV modules.

14 SOLAR ENERGY↗
DOE OSTI2023

Quantifying optical loss of high-voltage degradation modes in photovoltaic modules using spectral analysis

The direct current bias for photovoltaic (PV) modules interconnected in series-strings may include both high voltage negative (“HV-”) and positive (“HV+”) polarity with respect to the electrical ground. Multiple degradation modes, resulting in quantifiable optical loss, were found to occur during HV-/HV+ sequential stress, including corrosion of the external glass surface, encapsulant delamination (at its interfaces with the glass and the PV cell), internal haze formation (resulting from a chemical interaction between the glass and the encapsulant), corrosion and migration of the gridlines, and corrosion of the silicon nitride (Si x N y ) antireflective coating on the cell. The effects of these separate modes were examined using monolithic (e.g., glass or PV cell) and laminated-coupon (glass/encapsulant/glass or glass/encapsulant/cell/encapsulant/backsheet) specimens. Characterizations during and after unbiased accelerated testing at 85°C/85% relative humidity included spectrophotometry, optical microscopy, electron microscopy, and ellipsometry. For some module components (i.e., the glass and the Si x N y coating), the optical performance was determined through iterative analysis of empirical measurements. Concentrating on just their spectral effect, a novel model was then developed to estimate the transfer of light to the PV cell and the return of light from the PV module with simultaneous degradation mechanisms, which was compared with a mini-module previously subjected to HV-/HV+ stress. Here the model suggests that one third of the current loss observed for the mini-module can be attributed to the optical degradation of the packaging materials. The dominant degradation modes include encapsulant delamination and corrosion of the Si x N y coating. Recommendations are given so that the optical model may be improved relative to accelerated testing and validated relative to field aging.

14 SOLAR ENERGY↗
DOE OSTI2024

Quantifying spectral albedo effects on bifacial photovoltaic module measurements and system model predictions

We provide a comprehensive analysis of the effect of spectral albedo on photovoltaic (PV) module measurements and system model predictions. We demonstrate how to account for albedo in indoor bifacial device measurements by adjusting the applied irradiance using the scaled rear irradiance method, exemplified on fabricated silicon heterojunction (SHJ) modules. System model performance is studied using a detailed 3D finite-element model, DUET, for fixed-tilt and horizontal single-axis tracked (SAT) arrays between 15 and 75°N. Spectral effects cause variations in measured SHJ module short-circuit current up to 2% and efficiency variation up to 0.3% abs. We further demonstrate that rear-side spectral mismatch factors (SMMs) resulting from including or omitting spectral albedo in PV system modeling vary between ±13%, while total (front+rear) SMMs vary up to 3%, depending on the deployment configuration and latitude. SAT array SMMs are weakly correlated with latitude, while fixed-tilt array SMMs increase with latitude, driven by an increasing proportion of ground-reflected light on the front-side of modules. Ground-reflections can constitute between 2% and 32% of total incident module irradiance, with notably high (>10%) contributions for fixed-tilt arrays at high latitude. Effects of spectral albedo are most significant for: (1) fixed-tilt deployments at high latitudes, (2) wide bandgap technologies such as perovskite and cadmium telluride cells, (3) albedos which vary steeply over the technology's absorption range, and (4) high albedo ground covers. Overall, we demonstrate that omitting spectral albedo effects can result in PV measurement and system-level modeling uncertainties on the order of several percent in these cases.

14 SOLAR ENERGY↗
DOE OSTI2019

Effects of insertion loss, laser profile and inhomogeneity of dots distribution on properties of all-optical modulator based on GaN/AlN quantum dots

This paper reports the effects of insertion loss, laser profile and inhomogeneity of dots distribution on properties of an all-optical modulator based on spherical quantum dot. The aim of this paper is to give a quantitative description for the variation of main properties of an all-optical quantum dot modulator such as, absorption, transmission and modulation depth regard to insertion loss, laser profile and inhomogeneity of dots. To realize these points, first, we extract the field distribution in optical fiber and channel waveguide (modulator) which are defined by their structure characteristics and boundary conditions. Using the electric field equations, input coupling efficiency and insertion loss and also role of laser profile are observable. Finally we investigate the effect of size distribution and inhomogeneity of quantum dots on the modulator performance. In this structure we used electromagnetically induced transparency (EIT) in GaN/AlN structure, associated with inter-sublevel transitions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Design and performance evaluation of a dual-circuit thermal energy storage module for air conditioners

We present experimental results and a validated numerical model of a dual-circuit phase-change thermal energy storage module for air conditioners. The module incorporates a phase-change material encapsulated in compressed expanded natural graphite foam. We used n-tetradecane as the PCM with a transition temperature (~4.5 °C) suitable for air-conditioning applications. Heat exchange to and from the module is accomplished through two fluid loops operating as a heat source and sink embedded inside multiple slabs of the composite material. This dual-circuit design enables easier integration with air-conditioning equipment and provides enhanced flexibility in system operation as compared to the state-of-the-art thermal storage systems. When integrated with an air-conditioner, this design will enable peak-load shaving and enhances operational efficiency. The thermal storage device was designed for a nominal storage capacity of ~ 3.5 kWh. We evaluated the heat transfer and energy storage performance of this device using standalone heat transfer experiments to estimate key thermal resistances and identify design improvements before integration with an air conditioner. The numerical model of the heat exchanger uses a combination of discretized and lumped parameter approaches to maintain a balance between accuracy and computational expense. Our analyses show that the geometric features and integration of fluid tubes are key contributors to the thermal contact resistance between the fluid and the thermal storage material, and consequently, to the overall performance of the thermal storage module. Our standalone experiments also identified important operating scenarios in which this thermal storage module can be used for air-conditioning in buildings.

25 ENERGY STORAGE↗
DOE OSTI2015

NDR1 modulates the UV-induced DNA-damage checkpoint and nucleotide excision repair

Nucleotide excision repair (NER) is the sole mechanism of UV-induced DNA lesion repair in mammals. A single round of NER requires multiple components including seven core NER factors, xeroderma pigmentosum A–G (XPA–XPG), and many auxiliary effector proteins including ATR serine/threonine kinase. The XPA protein helps to verify DNA damage and thus plays a rate-limiting role in NER. Hence, the regulation of XPA is important for the entire NER kinetic. We found that NDR1, a novel XPA-interacting protein, modulates NER by modulating the UV-induced DNA-damage checkpoint. In quiescent cells, NDR1 localized mainly in the cytoplasm. After UV irradiation, NDR1 accumulated in the nucleus. The siRNA knockdown of NDR1 delayed the repair of UV-induced cyclobutane pyrimidine dimers in both normal cells and cancer cells. It did not, however, alter the expression levels or the chromatin association levels of the core NER factors following UV irradiation. Instead, the NDR1-depleted cells displayed reduced activity of ATR for some set of its substrates including CHK1 and p53, suggesting that NDR1 modulates NER indirectly via the ATR pathway. - Highlights: • NDR1 is a novel XPA-interacting protein. • NDR1 accumulates in the nucleus in response to UV irradiation. • NDR1 modulates NER (nucleotide excision repair) by modulating the UV-induced DNA-damage checkpoint response.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2017

Crystal structure and thermodynamic dissection of chitin oligosaccharide binding to the LysM module of chitinase-A from Pteris ryukyuensis

Highlights: • Crystal structure of a LysM module from Pteris ryukyuensis chitinase-A (PrLysM2) was determined at a resolution of 1.8 Å. • LysM module recognizes chitin oligosaccharides in a shallow groove on the molecule. • Thermodynamic dissection of the binding energetics of (GlcNAc){sub 6} to PrLysM2 was carried out. • The binding site comprises of five sugar-binding subsites. We determined the crystal structure of a LysM module from Pteris ryukyuensis chitinase-A (PrLysM2) at a resolution of 1.8 Å. Structural and binding analysis of PrLysM2 indicated that this module recognizes chitin oligosaccharides in a shallow groove comprised of five sugar-binding subsites on one side of the molecule. The free energy changes (ΔG{sub r}°) for binding of (GlcNAc){sub 6}, (GlcNAc){sub 5}, and (GlcNAc){sub 4} to PrLysM2 were determined to be −5.4, −5,4 and −4.6 kcal mol{sup −1}, respectively, by ITC. Thermodynamic dissection of the binding energetics of (GlcNAc){sub 6} revealed that the driving force is the enthalpy change (ΔH{sub r}° = −11.7 ± 0.2 kcal/mol) and the solvation entropy change (−TΔS{sub solv}° = −5.9 ± 0.6 kcal/mol). This is the first description of thermodynamic signatures of a chitin oligosaccharide binding to a LysM module.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2018

Assessing the Performance of a Physically-Based Soil Moisture Module Integrated within the Soil and Water Assessment Tool

A Richards equation-based soil moisture module was developed and integrated within the Soil and Water Assessment Tool (SWAT). Four years of daily soil moisture measurements from 10 monitoring stations at three depths (i.e., 5, 10, and 50 cm) in the Choptank River watershed, Maryland, were used to test the module performance. Results show that, as compared with the original SWAT soil moisture module, the Richards-equation-based soil moisture module improved R2 from 0.12 to 0.45 and reduced soil moisture simulation bias from -0.10 to -0.02, averaged across the 10 stations at soil surface layer (i.e., 5 cm depth). Noticeable improvements were also observed for deeper soil layers, and for both dry and wet periods. Notably, the soil moisture coupling strength between different soil layers was substantially improved with the new module. The enhanced SWAT model is expected to better inform soil water and irrigation management.

land surface processes, soil water, modelling↗
DOE OSTI2021

First ITER CS module test results

The ITER Central Solenoid (CS) is under fabrication by the US ITER organization and its subcontractors. US ITER will supply seven modules to ITER IO, six of which will be assembled in a stack that forms the ITER Central Solenoid, with one as a spare. The first module fabrication has been completed by General Atomics (GA) at their facility and has begun testing including high voltage testing, Paschen testing in the vacuum and then testing at 4.5 K and up to 40 kA in order to demonstrate compliance of the coil to ITER requirements. In the paper we present the Test Plan and results of the CS Module performance tests, especially at 40 kA current. Herein, AC losses, joint resistances and hydraulic characteristics of the coil are all measured. Displacements of the coil height and hoop strain of the CS Module are also measured to verify structural and mechanical characteristics of the coil along with cooldown shrinkage of the coil. This information is used for verification of the stack behavior of CS in ITER operation. The test results and preliminary analyses results are presented, compared to expectations, and discussed. All measured parameters suggest that the CS module will perform well in ITER machine.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗