Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mobility system technology”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Agricultural Aircraft Aid

Farmers are increasingly turning to aerial applications of pesticides, fertilizers and other materials. Sometimes uneven distribution of the chemicals is caused by worn nozzles, improper alignment of spray nozzles or system leaks. If this happens, job must be redone with added expense to both the pilot and customer. Traditional pattern analysis techniques take days or weeks. Utilizing NASA's wind tunnel and computer validation technology, Dr. Roth, Oklahoma State University (OSU), developed a system for providing answers within minutes. Called the Rapid Distribution Pattern Evaluation System, the OSU system consists of a 100-foot measurement frame tied in to computerized analysis and readout equipment. System is mobile, delivered by trailer to airfields in agricultural areas where OSU conducts educational "fly-ins." A fly-in typically draws 50 to 100 aerial applicators, researchers, chemical suppliers and regulatory officials. An applicator can have his spray pattern checked. A computerized readout, available in five to 12 minutes, provides information for correcting shortcomings in the distribution pattern.

Source record↗
NASA NTRS2015

High Resolution Nature Runs and the Big Data Challenge

NASA's Global Modeling and Assimilation Office at Goddard Space Flight Center is undertaking a series of very computationally intensive Nature Runs and a downscaled reanalysis. The nature runs use the GEOS-5 as an Atmospheric General Circulation Model (AGCM) while the reanalysis uses the GEOS-5 in Data Assimilation mode. This paper will present computational challenges from three runs, two of which are AGCM and one is downscaled reanalysis using the full DAS. The nature runs will be completed at two surface grid resolutions, 7 and 3 kilometers and 72 vertical levels. The 7 km run spanned 2 years (2005-2006) and produced 4 PB of data while the 3 km run will span one year and generate 4 BP of data. The downscaled reanalysis (MERRA-II Modern-Era Reanalysis for Research and Applications) will cover 15 years and generate 1 PB of data. Our efforts to address the big data challenges of climate science, we are moving toward a notion of Climate Analytics-as-a-Service (CAaaS), a specialization of the concept of business process-as-a-service that is an evolving extension of IaaS, PaaS, and SaaS enabled by cloud computing. In this presentation, we will describe two projects that demonstrate this shift. MERRA Analytic Services (MERRA/AS) is an example of cloud-enabled CAaaS. MERRA/AS enables MapReduce analytics over MERRA reanalysis data collection by bringing together the high-performance computing, scalable data management, and a domain-specific climate data services API. NASA's High-Performance Science Cloud (HPSC) is an example of the type of compute-storage fabric required to support CAaaS. The HPSC comprises a high speed Infinib and network, high performance file systems and object storage, and a virtual system environments specific for data intensive, science applications. These technologies are providing a new tier in the data and analytic services stack that helps connect earthbound, enterprise-level data and computational resources to new customers and new mobility-driven applications and modes of work. In our experience, CAaaS lowers the barriers and risk to organizational change, fosters innovation and experimentation, and provides the agility required to meet our customers' increasing and changing needs

big data analysis↗
NASA NTRSDate not supplied

NASA Advanced Space Suit Pressure Garment System Status and Development Priorities 2024

This paper discusses the current focus of NASA’s Advanced Space Suit Pressure Garment Technology Development team’s efforts, the status of that work, and a summary of longer term technology development priorities and activities. The Exploration Extra-vehicular Activity Mobility Unit (xEMU) has been the team’s primary effort over the past several years. This paper documents the various tests executed with the xPGS to evaluate its performance, durability, and acceptability for microgravity and Lunar missions. An overview of ongoing and planned xEMU testing and training is provided. The PGS team’s efforts in supporting the Exploration Extravehicular Activity Services (xEVAS) vendors is discussed. In addition, technology development efforts in coordination with the EVA and Human Surface Mobility Program (EHP), the NASA Engineering Safety Council (NESC) and the Small Business Innovation Research (SBIR) Program will be discussed in the context of supporting sustaining EVA operations on the Lunar surface over the coming decade. Finally, a brief review of longer-term pressure garment challenges and technology gaps will be presented to provide an understanding of the advanced pressure garment team’s technology investment priorities and needs.

Shane M McFarland↗
NASA NTRSDate not supplied

NASA Advanced Space Suit Pressure Garment System Status and Development Priorities 2024

This paper discusses the current focus of NASA’s Advanced Space Suit Pressure Garment Technology Development team’s efforts, the status of that work, and a summary of longer term technology development priorities and activities. The Exploration Extra-vehicular Activity Mobility Unit (xEMU) has been the team’s primary effort over the past several years. This paper documents the various tests executed with the xPGS to evaluate its performance, durability, and acceptability for microgravity and Lunar missions. An overview of ongoing and planned xEMU testing and training is provided. The PGS team’s efforts in supporting the Exploration Extravehicular Activity Services (xEVAS) vendors is discussed. In addition, technology development efforts in coordination with the EVA and Human Surface Mobility Program (EHP), the NASA Engineering Safety Council (NESC) and the Small Business Innovation Research (SBIR) Program will be discussed in the context of supporting sustaining EVA operations on the Lunar surface over the coming decade. Finally, a brief review of longer-term pressure garment challenges and technology gaps will be presented to provide an understanding of the advanced pressure garment team’s technology investment priorities and needs.

Shane McFarland↗
NASA NTRSDate not supplied

Data and Reasoning Fabric (DRF) Phase I & Phase II Report

A Data & Reasoning Fabric (DRF) is envisioned to enable the full potential of advanced air mobility by providing all data and reasoning where they are needed. The DRF marketplace is based on an open foundational ecosystem of data and reasoning exchange between the many systems that must seamlessly interplay to manage the envisioned highly complex and dense airspace operations. DRF activities will identify, test and - as needed - research and develop critical core technologies, and collaboratively test these technologies, open standards and architectures, and the integrated framework with end-users so as to deliver reference designs and development environments that catalyze broad private and public sector buy-in and self-sustaining development of it and associated standards.

UAM↗
NASA NTRSDate not supplied

A Data & Reasoning Fabric to Enable Advanced Air Mobility

A Data & Reasoning Fabric (DRF) is envisioned to enable the full potential of advanced air mobility by providing all data and reasoning where they are needed. The DRF marketplace is based on an open foundational ecosystem of data and reasoning exchange between the many systems that must seamlessly interplay to manage the envisioned highly complex and dense airspace operations. DRF activities will identify, test and - as needed - research and develop critical core technologies, and collaboratively test these technologies, open standards and architectures, and the integrated framework with end-users so as to deliver reference designs and development environments that catalyze broad private and public sector buy-in and self-sustaining development of it and associated standards.

Urban Air Mobility↗
DOE OSTI2026

Interactions Between Climate Policy and Technology-influenced Travel Behavior: Mitigating Induced Demand from CACC

Advances in vehicle technology have influenced the development of automated vehicle systems, where vehicles that do not require human intervention are already deployed in the roadway networks. While these advances are proved to increase roadway safety and highway capacity, more research is needed to understand the long-term and regional-level impacts on mobility, land use, energy consumption, and emissions. This study proposes a multi-model approach to analyze the effect of vehicle automation and deep decarbonization policies over a period from 2020 to 2040 in Austin, Texas. We use the Global Change Analysis Model (GCAM) to develop internally the scenarios that are then passed to the SMART Mobility modeling workflow, a large-scale simulation framework combining the POLARIS activity-based travel demand model and mesoscopic traffic simulator with the Autonomie vehicle energy consumption model and the UrbanSim land use simulator. Results suggest that the introduction of vehicles with advanced automation could increase fuel consumption when no decarbonization policies are implemented. Also, advances in vehicle technology research and development could lead to a decline in energy use in the long-term. Energy pricing and vehicle electrification incentives could help reduce the impact of vehicle automation. Finally, our analysis indicates the relevance of introducing land use processes in longterm vehicle automation studies.

land use↗
NASA NTRS2011

Spacesuit Portable Life Support System Breadboard (PLSS 1.0) Development and Test Results

A multi-year effort has been carried out at NASA-JSC to develop an advanced Extravehicular Activity (EVA) PLSS design intended to further the current state of the art by increasing operational flexibility, reducing consumables, and increasing robustness. Previous efforts have focused on modeling and analyzing the advanced PLSS architecture, as well as developing key enabling technologies. Like the current International Space Station (ISS) Extravehicular Mobility Unit (EMU) PLSS, the advanced PLSS comprises of three subsystems required to sustain the crew during EVA including the Thermal, Ventilation, and Oxygen Subsystems. This multi-year effort has culminated in the construction and operation of PLSS 1.0, a test rig that simulates full functionality of the advanced PLSS design. PLSS 1.0 integrates commercial off the shelf hardware with prototype technology development components, including the primary and secondary oxygen regulators, ventilation loop fan, Rapid Cycle Amine (RCA) swingbed, and Spacesuit Water Membrane Evaporator (SWME). Testing accumulated 239 hours over 45 days, while executing 172 test points. Specific PLSS 1.0 test objectives assessed during this testing include: confirming key individual components perform in a system level test as they have performed during component level testing; identifying unexpected system-level interactions; operating PLSS 1.0 in nominal steady-state EVA modes to baseline subsystem performance with respect to metabolic rate, ventilation loop pressure and flow rate, and environmental conditions; simulating nominal transient EVA operational scenarios; simulating contingency EVA operational scenarios; and further evaluating individual technology development components. Successful testing of the PLSS 1.0 provided a large database of test results that characterize system level and component performance. With the exception of several minor anomalies, the PLSS 1.0 test rig performed as expected; furthermore, many system responses trended in accordance with pre-test predictions.

Vogel, Matt R.↗
NASA NTRS1987

Helicopter transmission testing at NASA Lewis Research Center

The helicopter has evolved into a highly valuable air mobile vehicle for both military and civilian needs. The helicopter transmission requires advanced studies to develop a technology base for future rotorcraft advances. A joint helicopter transmission research program between the NASA Lewis Research Center and the U.S. Army Aviation Systems Command has existed since 1970. Program goals are to reduce weight and noise and to increase life and reliability. The current experimental activities at Lewis consist of full-scale helicopter transmission testing, a base effort in gearing technology, and a future effort in noise reduction technology. The experimental facilities at Lewis for helicopter transmission testing are described. A description of each of the rigs is presented along with some significant results and near-term plans.

Lewicki, David G.↗
NASA NTRS1991

Enabling the Space Exploration Initiative - NASA's Exploration Technology Program in space power

Space power requirements for SEI are reviewed, including the results of a NASA 90-day study and reports by the National Research Council, AIAA, NASA, the Advisory Committee on the Future of the U.S. Space Program, and the Synthesis Group. The space power requirements for the SEI robotic missions, lunar spacecraft, Mars spacecraft, and human missions are summarized. Planning for the exploration technology is addressed, including: photovoltaic, chemical, and thermal energy conversion; power management; thermal management; space nuclear power; high-capacity power; power and thermal management for the surface, earth-orbiting platform, and spacecraft; laser power beaming; and mobile surface systems.

Bennett, Gary L.↗
NASA NTRS2005

Demonstration of Four Operating Capabilities to Enable a Small Aircraft Transportation System

The Small Aircraft Transportation System (SATS) project has been a five-year effort fostering research and development that could lead to the transformation of our country s air transportation system. It has become evident that our commercial air transportation system is reaching its peak in terms of capacity, with numerous delays in the system and the demand keeps steadily increasing. The SATS vision is to increase mobility in our nation s transportation system by expanding access to more than 3400 small community airports that are currently under-utilized. The SATS project has focused its efforts on four key operating capabilities that have addressed new emerging technologies and procedures to pave the way for a new way of air travel. The four key operating capabilities are: Higher Volume Operations at Non-Towered/Non-Radar Airports, En Route Procedures and Systems for Integrated Fleet Operations, Lower Landing Minimums at Minimally Equipped Landing Facilities, and Increased Single Pilot Performance. These four capabilities are key to enabling low-cost, on-demand, point-to-point transportation of goods and passengers utilizing small aircraft operating from small airports. The focus of this paper is to discuss the technical and operational feasibility of the four operating capabilities and demonstrate how they can enable a small aircraft transportation system.

Viken, Sally A.↗
NASA NTRS2017

Greased Lightning (GL-10) Performance Flight Research: Flight Data Report

Modern aircraft design methods have produced acceptable designs for large conventional aircraft performance. With revolutionary electronic propulsion technologies fueled by the growth in the small UAS (Unmanned Aerial Systems) industry, these same prediction models are being applied to new smaller, and experimental design concepts requiring a VTOL (Vertical Take Off and Landing) capability for ODM (On Demand Mobility). A 50% sub-scale GL-10 flight model was built and tested to demonstrate the transition from hover to forward flight utilizing DEP (Distributed Electric Propulsion)[1][2]. In 2016 plans were put in place to conduct performance flight testing on the 50% sub-scale GL-10 flight model to support a NASA project called DELIVER (Design Environment for Novel Vertical Lift Vehicles). DELIVER was investigating the feasibility of including smaller and more experimental aircraft configurations into a NASA design tool called NDARC (NASA Design and Analysis of Rotorcraft)[3]. This report covers the performance flight data collected during flight testing of the GL-10 50% sub-scale flight model conducted at Beaver Dam Airpark, VA. Overall the flight test data provides great insight into how well our existing conceptual design tools predict the performance of small scale experimental DEP concepts. Low fidelity conceptual design tools estimated the (L/D)( sub max)of the GL-10 50% sub-scale flight model to be 16. Experimentally measured (L/D)( sub max) for the GL-10 50% scale flight model was 7.2. The aerodynamic performance predicted versus measured highlights the complexity of wing and nacelle interactions which is not currently accounted for in existing low fidelity tools.

McSwain, Robert G.↗
NASA NTRSDate not supplied

An Initial Assessment of Variable Depth Liner Optimization for Ducted Proprotor Applications

The rise of the Urban Air Mobility market has spurred the design of a new generation of novel aircraft. To aid industry and researchers interested in these types of aircraft, the Revolutionary Vertical Lift Technology project at NASA has developed a fleet of reference vehicles for system studies. A new six-passenger reference vehicle has recently been added to the research portfolio that has ducted proprotors for propulsors. The ducts present an opportunity to apply acoustic treatment to the interior of the duct that could target both tonal and broadband noise, representative of the sound produced by this type of propulsor. In this paper, design methodologies are presented to design a variable depth liner for this application. An optimizer is used to design multiple liners with variable chamber depths. Experimental results from normal impedance testing are compared to numerical predictions using the optimizer model and a finite element model. Results show that an optimizer can be used to design an acoustic liner with favorable performance for a broad range of frequencies, which could be appropriate for a ducted proprotor application.

Matthew B Galles↗
NASA NTRSDate not supplied

Autonomous Contingency Management In Urban Air Mobility: The Communication Network Awareness Machine System

Next Generation Air Transportation System (NextGen) has begun the modernization of the nation’s air transportation system (NAS), with goals to improve system safety, increase operation efficiency and capacity, provide enhanced predictability, resilience and robustness [1]. The overall objective of the Air Traffic Management-eXploration (ATM-X) project is to facilitate the goals of NextGen by conducting research to enable the growing demand of new, mission variant, air vehicles with safe access to the NAS. The implementation and utilization of new and burgeoning technologies that are both flexible, scalable, and systematically user-focused are requisite for ATM-X to achieve its intention of NAS safe entry [2]. Researchers from NASA Langley’s Flight Deck Integration Team have developed a system architecture that would allow ATM-X to leverage the necessary capabilities of an Increasingly Autonomous System (IAS), machine-agent that will promote the safe access and operation of air vehicles within what has become the byproduct of NextGen modernization, a Net-Centric airspace architecture and an Urban Air Mobility (UAM) community. Conducting flight operations within this type of architecture constrains the human-agent’s natural ability by data management. When the massive volume of data, its types, and the acquisition speed at which the data is ingested is observed it becomes evident that the human-agent will be functioning at an operational disadvantage. Therefore, the development and integration of intelligent machine-agents into the flight deck are a necessary implementation to achieve ATM-X overall objective of safe access and operation in the NAS.

Urban Air Mobility↗
DOE OSTI2023

The Evolution of Wayfinding Within Airports

The process of navigating within airports has evolved over the years, with various technologies emerging. Historically, wayfinding began with static signage and airport staff members before progressing into digital signs, interactive kiosks and displays. In recent years, wayfinding has continued along its digital path through the use of indoor positioning technology, mobile applications, and even robot guides. The future of wayfinding will likely be heavily linked to further digital developments such as facial recognition and autonomous vehicle navigation. This paper delves into the history of interior wayfinding in airports, its present state, and the anticipated future. Key wayfinding technologies are discussed in detail with an emphasis on smartphone applications. Other considerations such as traveler stress, legal issues, pandemic safety, and language barriers are included.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS2018

UAS-Based P-Band Signals of Opportunity for Remote Sensing of Snow and Root Zone Soil Moisture

We have developed the P-band Signals of Opportunity (SoOp) sensor based on the Unmanned Aircraft System (UAS) to remotely sense Snow Water Equivalent (SWE) and Root Zone Soil Moisture (RZSM). The P-band UAS SoOp sensor for Hydrology (UASHydro) would operate on the S2 aircraft developed by Black Swift Technologies for sensing of SWE and RZSM with a spatial resolution of about 10m. Root-zone soil moisture and snow water storage in land are critical parameters of the water cycle. The long-term goal of our development would be to use small UAS to perform regional high resolution observation of two key hydrological measurements to improve the estimation of terrestrial water storage for water management, crop production and forecasts of natural hazard. The UASHydro concept utilizes passive receivers to detect the reflection of strong existing P-band radio signals at the 360-380 MHz band from geostationary Mobile Use Objective System (MUOS) communication satellites launched by the US Navy. The SWE remote sensing measurement principle using the P-band SoOp is based on the propagation delay (or phase change) of radio signals through the snowpack. The time delay of the reflected signal due to the snowpack with respect to snow-free conditions is directly proportional to the snowpack SWE, while the soil moisture can be retrieved from the reflectivity at the P-band frequencies for MUOS. We have been conducting ground-based campaigns to test the instrumentation and data processing methods at the Fraser Experimental Forest in Colorado since February 2016. The field campaign data has provided support to the measurement concept. To install the SoOp technologies on the UAS, a lightweight antenna has been built and interfaces with the S2 built by Black Swift Technologies have been completed. A set of flights have been planned starting April 2018 through the end of 2018 in Colorado.

Elston, Jack↗
NASA NTRSDate not supplied

Hazard Perception & Avoidance (HPA), Assured Vehicle Automation 1 Simulation (AVA-1h) Results Outbrief

In late 2022, the Human Autonomy Teaming Lab (NASA Ames Research Center) conducted a manned, human-in-the-loop (HITL) simulation. This HITL was the lab’s second Hazard Perception and Avoidance (HPA) technical work under NASA’s Advanced Air Mobility (AAM), Automated Flight and Contingency Management (AFCM) Sub-Project. The goals were to assess detect and avoid technology for manned, electric vertical takeoff and landing (eVTOL) aircraft. This simulation tested Resolution Advisory (RA) responses and return-to-course (RTC) maneuvers for the second version of the Airborne Collision Avoidance System’s (ACAS) rotary-wing (Xr) variant. This was conducted at the center's Vertical Motion Simulator (VMS), on a motion-based platform, and was configured to fly eVTOL aircraft while maneuvering for intruding traffic. Variables for this study included ACAS Xr modes (i.e., TA/RA and DAA) and phases of flight (i.e., Cruise, Hover, and Approach). The data collected included response times, losses of well clear, and pilots' noncompliances to alerts and guidance as well as subjective ratings like acceptability and perceived workload. Additional details and future anticipations are also discussed.

ACAS Xr↗
DOE OSTI2024

Investigation of Ammonia Carrier Materials for Next Generation Ammonia Dosing System - CRADA 334 (Abstract)

Lean-burn gasoline and diesel engines can offer substantially higher fuel efficiency, good driving performance, and reduced carbon dioxide emission compared to stoichiometric gasoline engines. Various catalyst technologies have been developed to remove the pollutants from these engines. For example, a three-way catalyst (TWC) is used to remove hydrocarbons (HC), carbon monoxide (CO), and nitrogen oxides (NOx) from gasoline engines during the stoichiometric conditions. During the lean-burn conditions, a TWC or a diesel oxidation catalyst (DOC) is used to control HC and CO emissions. NOx is removed by either lean NOx trap catalyst (LNT) that can store NOx under lean conditions and reduce NOx under rich conditions, or selective catalytic reduction catalyst (SCR) that can selectively remove NOx with a reducing agent. Among the NOx reduction catalyst technologies, SCR offers a number of advantages, including excellent NOx reduction efficiency over a wide range of temperatures and overall lower system cost. In fact, the SCR technology using ammonia (NH3) as reductant has been proven effective and used commercially for the removal of NOx emissions from stationary sources since the 1970s. Currently, SCR is being used to meet the NOx emission standards for diesel engines in Europe and North America, and also being considered for meeting the future NOx emission standards for lean-burn gasoline engines. Because of the challenges associated with storage, handling and transportation of ammonia on a vehicle, aqueous urea solution (e.g., Diesel Exhaust Fluid, AdBlue) has been developed as ammonia storage compound for mobile applications. When the aqueous urea solution is sprayed into exhaust gas stream, urea is decomposed to release ammonia, which then reduces NOx over the downstream SCR catalyst. Although aqueous urea solution technology has enabled automakers and engine manufacturers to meet the current NOx emission standards, this process of releasing ammonia requires a hot exhaust gas and sufficient mixing, creating challenges for low temperature NOx emission control and aftertreatment system packaging. For these reasons, alternative technologies have been developed as ammonia sources (e.g., solid urea, ammonium carbamate, metal ammine chloride) during the past few years. These technologies promise more convenient handling and distribution of ammonia sources, and help maximize the low-temperature performance of SCR catalysts and reduce the overall system volume and weight. However, none of these alternative technologies can be successfully implemented without the industry consensus. Therefore, the USCAR SCR work group, which is comprised of representatives from GM, Ford, and Chrysler, has decided to investigate the potential alternative ammonia carriers, define common standard vehicle interfaces, and address personal and environmental safety concerns with part suppliers and chemical companies. Under this CRADA Project, USCAR and Battelle will investigate alternative ammonia carrier materials that are currently under development. Based on the data and information derived under the CRADA project, the USCAR SCR work group plans to build the consensus and make recommendations for the industry.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗