Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effects of irradiation temperature on the microstructure and deuterium retention in γ-LiAlO 2 pellets

This report presents the experimental findings obtained from November 2023 to September 2024. The study aims to investigate the effects of temperature on the microstructure, deuterium (D) retention, and lithium (Li) loss in γ-LiAlO 2 pellets subjected to sequential He + and D + ion irradiation to a high dose. Sequential ion irradiation has been a key method in our previous studies to simulate the behavior of γ-LiAlO 2 under neutron irradiation. In addition to dose and dose rate, irradiation temperature is a critical factor influencing microstructural and compositional changes. LiAl 5 O 8 precipitates have been observed in γ-LiAlO 2 pellets irradiated with reactor neutrons at ~300°C. These precipitates also form during ion irradiation at an elevated temperature of 500°C, but not at 300°C. In our ion irradiation experiments, the dose rate is typically three orders of magnitude higher than that of neutron irradiation, leading to a more rapid damage production. To better emulate the microstructural features in neutron-irradiated pellets using ion irradiation, a higher irradiation temperature is needed to accelerate the diffusion of point defects and enhance defect recovery rates, thereby compensating for the effects of the higher dose rate. The microstructural changes observed are the result of competing processes occurring during ion irradiation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Microstructure Validation of Graph Theory Model-Derived Cooling Rates in the Wire Arc Additive Manufacturing of ER70S-6 Steel

Wire arc additive manufacturing (WAAM) enables high-rate fabrication of large metallic components, but spatial variations in thermal history can lead to microstructural heterogeneity that requires efficient process models to evaluate. This study evaluates whether cooling rates extracted from a graph theory model (GTM)-based thermal simulation are consistent with the microstructural evolution observed in an ER70S-6 WAAM wall. Thermal histories from the model were analyzed at selected build heights, and cooling rates were extracted from the final thermal excursion through the austenite phase field. Microstructures at corresponding locations were characterized using electron backscatter diffraction (EBSD) to quantify grain size distributions, and pearlite interlamellar spacing was used as an additional indicator of cooling behavior. The modeled cooling rates were highest near the substrate and generally decreased with build height, consistent with the observed reduction in the fine grain fraction and the progressive shift in the grain size distribution as build height increased. Pearlite spacing trends also supported the modeled cooling rate variation. These results indicate that GTM-derived thermal histories can be post-processed into metallurgically meaningful cooling rate estimates for WAAM steel builds and linked to dataset specific empirical grain size distribution relationships for process–thermal history–microstructure assessment.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructure and Mechanical Properties of Intercritically Treated Grade 91 Steel

Premature creep failures at the intercritical heat affected zone (ICHAZ) of creep-resistant steel weldments have been frequently reported. However, the creep degradation mechanism of different microstructure constituents in ICHAZ is complicated and needs further clarification. In this work, Grade 91 steel was intercritically heat-treated at a temperature (860 °C) between the critical temperatures AC1 and AC3, and a correlation between microstructure and mechanical properties of the heat-treated specimen was built. The effects of austenitization and tempering resulting from the intercritical treatment (IT) differentiated the local strain energies between the two microstructure constituents: newly transformed martensite (NTM) and over-tempered martensite (OTM). The formation of NTM grains led to a hardness increase from 247 HV0.5 in the base metal to 332 HV0.5 in the IT specimen. The ultimate tensile strength (UTS) increased from 739 MPa in the base metal to 1054 MPa in the IT specimen. Extensive growth of the OTM grains and rapid recovery of NTM grains took place simultaneously in the IT specimen during a typical tempering at 760 °C. These microstructure degradations led to a lowered hardness of 178 HV0.5, a reduced UTS of 596 MPa, and a poor creep resistance with a minimum creep strain rate of 0.49 %/h at 650 °C in an IT + tempering (ITT) specimen.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tailoring Microstructure and Mechanical Properties of Additively-Manufactured Ti6Al4V Using Post Processing

Additively-manufactured Ti-6Al-4V (Ti64) exhibits high strength but in some cases inferior elongation to those of conventionally manufactured materials. Post-processing of additively manufactured Ti64 components is investigated to modify the mechanical properties for specific applications while still utilizing the benefits of the additive manufacturing process. The mechanical properties and fatigue resistance of Ti64 samples made by electron beam melting were tested in the as-built state. Several heat treatments (up to 1000 °C) were performed to study their effect on the microstructure and mechanical properties. Phase content during heating was tested with high reliability by neutron diffraction at Los Alamos National Laboratory. Two different hot isostatic pressings (HIP) cycles were tested, one at low temperature (780 °C), the other is at the standard temperature (920 °C). The results show that lowering the HIP holding temperature retains the fine microstructure (~1% β phase) and the 0.2% proof stress of the as-built samples (1038 MPa), but gives rise to higher elongation (~14%) and better fatigue life. The material subjected to a higher HIP temperature had a coarser microstructure, more residual β phase (~2% difference), displayed slightly lower Vickers hardness (~15 HV10N), 0.2% proof stress (~60 MPa) and ultimate stresses (~40 MPa) than the material HIP’ed at 780 °C, but had superior elongation (~6%) and fatigue resistance. Heat treatment at 1000 °C entirely altered the microstructure (~7% β phase), yield elongation of 13.7% but decrease the 0.2% proof-stress to 927 MPa. The results of the HIP at 780 °C imply it would be beneficial to lower the standard ASTM HIP temperature for Ti6Al4V additively manufactured by electron beam melting.

36 MATERIALS SCIENCE↗
DOE OSTI2011

Microstructure Evolution of Gas Atomized Iron Based ODS Alloys

In a simplified process to produce precursor powders for oxide dispersion-strengthened (ODS) alloys, gas-atomization reaction synthesis (GARS) was used to induce a surface oxide layer on molten droplets of three differing erritic stainless steel alloys during break-up and rapid solidification. The chemistry of the surface oxide was identified using auger electron spectroscopy (AES) and scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS). The precursor iron-base powders were consolidated at 850 C and 1,300 C using hot isostatic pressing (HIPing). Consolidation at the lower temperature resulted in a fully dense microstructure, while preventing substantial prior particle-boundary-oxide dissociation. Microstructural analysis of the alloys consolidated at the higher temperature confirmed a significant reduction in prior-particle-boundary-oxide volume fraction, in comparison with the lower-temperature-consolidated sample. This provided evidence that a high-temperature internal oxygen-exchange reaction occurred between the metastable prior particle-boundary-oxide phase (chromium oxide) and the yttrium contained within each prior particle. This internal oxygen-exchange reaction is shown to result in the formation of yttrium-enriched oxide dispersoids throughout the alloy microstructure. The evolving microstructure was characterized using transmission electron microscopy (TEM) and high-energy X-ray diffraction (HE-XRD).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructural and Micro-Chemical Evolutions in the Irradiated UCO Fuel Kernels of AGR-1 and AGR-2 TRISO Fuel Particles

AGR-1 and AGR-2 TRISO fuel particles were fabricated with slightly different fuel kernel chemical compositions, modified fabrication processes, different fuel kernel diameters, and changed 235U enrichments. To correlate those differences with the fuel kernel responses to neutron irradiations in terms of irradiated fuel microstructure, fission products chemical and physical states, and fission gas bubble evolutions, extensive microstructural and analytical characterizations were conducted. The studies used a state of art transmission electron microscopy (TEM) equipped with Energy-dispersive X-ray spectroscopy (EDS) of four silicon solid-state detectors which have super sensitivity and fast speed. The TEM specimens were prepared from selected AGR-1 and AGR-2 irradiated fuel kernels exposed to safety testing after irradiation. The particles were chosen to represent a representative irradiation conditions with a fuel burnup within the range from 10.8 to 18.6% FIMA, and the time-average volume-average temperatures vary from 1070 to 1287°C. The 235U enrichment was 19.74 wt.% for the AGR1 fuel kernels and 14.03 wt.% for the AGR-2 fuel kernels. The TEM results show that there were significant microstructural reconstructions in the irradiated fuel kernels for both the AGR-1 and AGR-2 fuels. There are four major phases including fuel matrix of UO2 and UC, U2RuC2, and UMoC2 in the irradiated AGR2 fuel kernel. Zr and Nb form solid solution in the UC phase. UMoC2 phase often shows a detectable concentration of Tc. Pd was found to mainly locate in the buffer layer or to be associated with fission gas bubble within the UMoC2 phase. The EDS maps qualitatively show that the rare-earth fission products (Nb, et al.) preferentially reside in the UO2 phase. In contrast, in the irradiated AGR1 fuel kernel, no U2RuC2 or UMoC2 precipitates were positively identified. Instead, there is a high number of rod-shape precipitates enriched with Ru, Tc, Rh, and Pd observed in the fuel kernel center and edge zone. The difference of microstructural and micro-chemical evolutions in irradiated fuel kernels between the AGR-1 and AGR-2 TRISO fuel particle may result from a combined factor of irradiation temperature, fuel geometry and chemical composition. However, the irradiation temperature probably play a more deterministic role. Limited electron energy loss spectroscopy (EELS) characterizations on the AGR2 fuel kernel show that there is nearly no carbon in the UO2 phase while a small fraction of oxygen was detected in the UC/UMoC2 phase.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2016

Microstructural Characteristics of U-Zr Ingot Slug and Atomized Powder for SFR metal Fuel

Rod-type fuel slugs and spherical powder of U- 10wt.%Zr alloy was also fabricated and characterized in microstructure by injection casting, gravity casting and centrifugal atomization process. U grains became finer from ∼30μm in conventionally ingot rod to ∼2μm in atomized powder. Laminar structure became so fine from ∼0.2μm in conventionally cast ingot rod to 0.05∼0.1μm in atomized powder. Metallic fuels such as U-Zr and U-Pu-Zr alloys have been considered as a nuclear fuel for a sodium-cooled fast reactor (SFR), related to the closed fuel cycle for managing minor actinides and reducing a high radioactivity levels since the 1980's. Metallic fuel slugs of U-Pu-Zr alloys for SFR have conventionally been fabricated by an injection casting method. U-Pu-Zr alloy melts are injected and cast into quartz tube molds during injection casting. Metallic fuel slugs are collected by fracturing quartz tubes from the molds. Demolded quartz tubes are treated with radioactive wastes. Recently, management of minor actinides (MA) became an important issue because direct disposal of the long-lived MA can be a long-term burden for a tentative repository up to several hundreds of thousand years. The metallic fuel for SFR should be remotely fabricated under a radiation shielded environment such as a hot cell, because it contains highly radioactive MA such as Np, Am and Cm. The addition of MA in the fuel composition introduces new challenges in the manufacturing of a metallic fuel slug. Am has a high vapor pressure under a vacuum atmosphere at above a melting temperature of U-Zr or U-Pu-Zr. Used graphite crucibles and quartz molds cannot be recycled easily because of difficult decontamination of radioactive residues on their surfaces. It is necessary to minimize the vaporization of Am and volume of radioactive wastes. Atomized metallic fuel does not need these quartz molds during fabrication, as uranium alloys are prepared as a particle form. It is possible to reduce the formation of radioactive wastes by applying the fabrication process of a particulate metallic fuel. Metallic fuel having a fine microstructure, which originates from a rapid solidification effect during atomization process, results in a higher FG release rate during irradiation. In the case of applying a new forming method such as vibrocompaction in Zr sheath, the sheath can act as a reliable FCCI (fuel/cladding chemical interaction) barrier and a re-constraint for external elongation. In addition, atomized fuel powder, dispersed in a Na liquid metal having a high thermal conductivity, may have a lower temperature distribution during irradiation. In order to develop an efficient fabrication process of metallic fuel for SFR, U-Zr ingot rods were fabricated in a lab-scale with various casting methods. Rod-type U-Zr fuel slugs were fabricated by gravity casting and injection casting. Spherical powder of U-Zr alloy was also fabricated by centrifugal atomization. And then, the microstructural characteristics were investigated by using electron microscopes and energy-dispersive electron X-ray spectroscopy. Atomized U-10Zr powder generally showed spherical morphology of below 200 μm in particle size. U grains became finer from ∼30 μm in conventionally ingot rod to ∼2 μm in atomized powder. Laminar structure became so fine from ∼0.2 μm in conventionally cast ingot rod to 0.05∼0.1 μm in atomized powder. Atomized particulate metallic fuel for SFR has a fine microstructure, resulting in a higher fission gas release rate during irradiation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2017

Hydride Microstructure at the Metal-Oxide Interface of a Zircaloy-4 Fuel Clad from the H.B. Robinson Nuclear Reactor

During nuclear reactor operation, some of the hydrogen that is produced by the water side corrosion is uptaken by cladding. When the uptaken hydrogen content exceeds its solubility limit in the cladding at a specific temperature, it precipitates as hydride particles in the cladding. This process occurs immediately at the metal-oxide interface forming a hydride rim because of the temperature gradient in the cladding. The presence of hydride rim and its microstructure severely reduces the cladding strength and can induce crack initiation and propagation during design basis accidents, transportation, and wet/dry storage. Because hydrides platelets are one of the potent crack initiation sites, microstructural characterization of hydride rim becomes essential to the safe operation of nuclear reactor and spent nuclear fuel retrievability. Therefore, we investigate the hydride rim microstructure at the metal oxide interface using scanning transmission electron microscopy (S/TEM) with Energy Dispersive X-ray Spectroscopy (EDS) that allows for the microstructural and local chemistry characterization of hydride precipitates to be determined, and enables a relationship to be derived on how the precipitate sites are affected by the oxide and their complex stacking behavior of the precipitates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

When and Where Lithium Plating Occurs, Its Correlation with Microstructure Heterogeneity, and the Mechanisms That Initiate and Self-Regulate Electrochemical Heterogeneity (A02-0444)

A microstructure scale electrochemical LIB model was used to investigate lithium plating onset, material non-uniform utilization, and in-plane heterogeneities for an NMC-graphite full cell. Model predicts active material particle surface roughness and size distribution (respectively, non-uniform curvature within and between particles) initiate in-plane heterogeneity, and that particle size heterogeneity at the separator interface controls the lithium plating preferential deposition ("Where"). These in-plane heterogeneities are then exacerbated by through-plane heterogeneities induced at fast charge as electrolyte depletion occurs and concentrates intercalation reaction near the anode-separator interface. Also, magnitude and occurrence of lithium plating is controlled by effective, or macroscale, microstructure parameters ("When"). As local states of charge start to diverge between nearby active material regions, overpotential differences induced by OCP difference kick in and contribute to reduce these SOC local heterogeneities. However, for staged materials such as graphite, with OCP profile alternating between plateaus and varying regions, this balancing mechanism is, respectively, inactive and active. This leads to a dynamic, non-monotonic, in-plane heterogeneity time evolution for state of charge and Faraday current density, for which their respective in-plane heterogeneity magnitude alternates. Such behavior has been modeled both for the whole electrode at the microstructure scale and at the particle scale. In-plane heterogeneities are usually considered to be detrimental, as they result in material non-uniform utilization (i.e., under and over stressed regions) and earlier degradations. However, this work provides a more granular approach as it discriminates between a harmful in-plane heterogeneity (non-uniform curvature) that triggers SOC in-plane heterogeneity, and a beneficial in-plane heterogeneity (Faraday current density) that contributes to reduce SOC in-plane heterogeneity. This work comprehensively explains the mechanisms that initiate, exacerbate, and regulate heterogeneity at the microstructure scale, while providing some design suggestions to reduce both in-plane and through-plane heterogeneities, as summarized in the graphical abstract.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

A Machine Learning Approach to Quantitative Analysis of Enamel Microstructure from Scanning Electron Microscopy Images

Dental enamel, the outermost tissue of mammalian teeth, must withstand a lifetime of wear and cyclic contact. To meet this demand, enamel possesses a combination of high hardness and resistance to fracture, properties that are typically mutually exclusive. The impressive damage tolerance has been attributed largely to decussation of the enamel rods, the principal unit of its microstructure. As such, enamel is inspiring the design of next‐generation structural materials. However, quantitative descriptions of the decussated enamel rod microstructure remain limited due to challenges encountered in applying computed tomography and in acquiring quality images appropriate for traditional digital processing methods. Here, a machine learning segmentation method is applied to images of the enamel obtained using scanning electron microscopy to support quantitative analysis of the microstructure. A pretrained convolutional neural network is used to expand the input training image dataset to allow the training of a random forest classifier, which ultimately segments the image with a very small training set ( n = 3 images). A validation of this segmentation method is presented, in addition to its application to calculate relevant microstructural parameters for images of tooth enamel from selected mammalian species. The methodology applied here is equally applicable to other hard tissues.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructural modification of a high-pressure die-cast A380 alloy through friction stir processing and its effect on mechanical properties

Aluminum alloy A380 is one of the major high-pressure die-cast (HPDC) alloys fabricated in the die casting sector. However, microstructural features such as shrinkage and gas porosity, entrapped oxide inclusions, change in the morphology of eutectic Si particles as a function of casting location, and the presence of multiple second phase particulates, especially Fe-bearing phases in HPDC A380 alloy results in limited ductility, thus, affecting its structural application. However, through proper modification of the as-cast microstructure, it is possible to improve the mechanical performance of alloy A380. In this study, we report the effect of friction stir processing (FSP), a well-known severe plastic deformation (SPD) and thermomechanical processing tool for selective microstructural modification, on A380. FSP effectively refines the as-cast microstructure and breaks down the coarse Si particles, creating a homogenized distribution of equiaxed Si particles in the aluminum matrix. Additionally, FSP eliminates porosity that acts as crack initiation sites, leading to improved mechanical strength and ductility.

Friction stir processing, Aluminum alloys, Mechani↗
DOE OSTI2017

Mechanical and Microstructural Effects of Thermal Aging on Cast Duplex Stainless Steels by Experiment and Finite Element Method

Cast duplex stainless steel piping in light water nuclear reactors expe- rience thermal aging embrittlement during operational service. Interest in extending the operational life to 80 years requires an increased understanding of the microstructural evolution and corresponding changes in mechanical behavior. We analyze the evolution of the microstructure during thermal aging of cast CF-3 and CF-8 stainless steels using electron microscopy and atom probe tomography. The evolution of the mechanical properties is measured concurrently by mechanical methods such as tensile tests, Charpy V-notch tests, and instrumented nanoinden- tation. A microstructure-based finite element method model is developed and uti- lized in conjunction with the characterization results in order to correlate the local stress-strain effects in the microstructure with the bulk measurements. This work is supported by the DOE Nuclear Energy University Programs (NEUP), contract number DE-NE0000724.

36 MATERIALS SCIENCE↗
DOE OSTI2015

The effects of annealing on the microstructure and mechanical properties of Fe 28 Ni 18 Mn 33 Al 21

In this paper, As-cast Fe 28 Ni 18 Mn 33 Al 21 , which consists of aligned, 50 nm, (Ni, Al)-rich B2, and (Fe, Mn)-rich f.c.c. phases, was annealed at a variety of temperatures up to 1423 K and the microstructure and mechanical properties were examined. It was shown that the as-cast microstructure arises from a eutectoid transformation at ~1300 K. Annealing at temperatures ≤1073 K produces β-Mn-structured precipitates and hardness values up to 816 HV, while annealing at temperatures >1073 K leads to dramatic coarsening of the two-phase B2/f.c.c. microstructure (up to 5.5 µm after 50 h at 1273 K), but does not lead to β-Mn precipitation. Interestingly, annealing at temperatures >1073 K delays the onset of β-Mn precipitation during subsequent anneals at lower temperatures. Coarsening the B2/f.c.c. lamellar structure by annealing at higher temperatures softens it and leads to increases in ductility from fracture before yield to ~8 % elongation. Finally, the presence of β-Mn precipitates makes the very fine, brittle B2/f.c.c. microstructures even more brittle, but significant ductility (8.4 % elongation) is possible even with β-Mn precipitates present if the B2/f.c.c. matrix is coarse and, hence, more ductile.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Segregated Approach for Modeling the Electrochemistry in the 3-D Microstructure of Li-Ion Batteries and Its Acceleration Using Block Preconditioners

Abstract Battery performance is strongly correlated with electrode microstructure. Electrode materials for lithium-ion batteries have complex microstructure geometries that require millions of degrees of freedom to solve the electrochemical system at the microstructure scale. A fast-iterative solver with an appropriate preconditioner is then required to simulate large representative volume in a reasonable time. In this work, a finite element electrochemical model is developed to resolve the concentration and potential within the electrode active materials and the electrolyte domains at the microstructure scale, with an emphasis on numerical stability and scaling performances. The block Gauss-Seidel (BGS) numerical method is implemented because the system of equations within the electrodes is coupled only through the nonlinear Butler–Volmer equation, which governs the electrochemical reaction at the interface between the domains. The best solution strategy found in this work consists of splitting the system into two blocks—one for the concentration and one for the potential field—and then performing block generalized minimal residual preconditioned with algebraic multigrid, using the FEniCS and the Portable, Extensible Toolkit for Scientific Computation libraries. Significant improvements in terms of time to solution (six times faster) and memory usage (halving) are achieved compared with the MUltifrontal Massively Parallel sparse direct Solver. Additionally, BGS experiences decent strong parallel scaling within the electrode domains. Last, the system of equations is modified to specifically address numerical instability induced by electrolyte depletion, which is particularly valuable for simulating fast-charge scenarios relevant for automotive application.

25 ENERGY STORAGE↗
DOE OSTI2014

Microstructure and Mechanical Properties of Laves Phase-strengthened Fe-Cr-Zr Alloys

Laves phase-reinforced alloys have shown some preliminary promising performance at room temperatures. This paper aims at evaluating mechanical properties of Laves phase-strengthened alloys at elevated temperatures. Three Fe-Cr-Zr alloys were designed to favor the formation of eutectic microstructures containing Laves and body-centered cubic phases with the aid of thermodynamic calculations. Microstructural characterization was carried out on the alloys in as-processed and aged states using optical microscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction. The effect of thermal aging and alloy composition on microstructure has been discussed based on microstructural characterization results. Mechanical properties have been evaluated by means of Vickers microhardness measurements, tensile testing at temperatures up to 973.15 K (700.15 °C), and creep testing at 873.15 K (600.15 °C) and 260 MPa. Alloys close to the eutectic composition show significantly superior strength and creep resistance compared to P92. Finally, however, their low tensile ductility may limit their applications at relatively low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Using In Situ Neutron Diffraction to Isolate Specific Features of Additively Manufactured Microstructures in 304L Stainless Steel and Identify Their Effects on Macroscopic Strength

Additive manufacturing of metal components results in unique microstructures with, necessarily, mechanical properties that are distinct from conventionally produced components. In this paper, four distinct microstructural features associated with directed energy deposition of 304L stainless steels, their stability, and their influences on flow strength were examined. These were (1) high dislocation density comparable with deformed materials, (2) increased ferrite content, (3) local chemical heterogeneity, and (4) tortuous grain morphology. In situ neutron diffraction measurements were used to monitor the evolution of the as-built microstructure during post-build heat treatment and relate the specific microstructural features to the strength behavior of the material following the heat treatment. The increased flow strength of the additively manufactured material relative to wrought counterparts is found to be due primarily to an increased dislocation density in the as-built material. However, the increased dislocation density does not completely account for the increased strength and it is hypothesized that some of the additional strength is related to the unique AM grain structure.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure-Based Estimation of Strength and Ductility Distributions for \(\alpha +\beta \) Titanium Alloys

Titanium alloys are processed to develop a wide range of microstructure configurations and therefore material properties. While these properties are typically measured experimentally, a framework for property prediction could greatly enhance alloy design and manufacturing. In this work, a microstructure-sensitive framework is presented for the prediction of strength and ductility as well as estimates of the bounds in variability for these properties. The framework explicitly considers distributions of microstructure via new approaches for instantiation of structure in synthetic samples. The parametric evaluation strategy, including the finite element simulation package FEpX, is used to create and test virtual polycrystalline samples to evaluate the variability bounds of mechanical properties in Ti-6Al-4V. Critical parameters for the property evaluation framework are provided by measurements of single crystal properties and advanced characterization of microstructure and slip system strengths in 2D and 3D. Property distributions for yield strength and ductility are presented, along with the validation and verification steps undertaken. Comparisons between strain localization and slip activity in virtual samples and in experimental grain-scale strain measurements are also discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The Effects of Silicon and Niobium Concentration on the Solidification Behavior and Microstructure of Cast Monel Alloys

Cast Monel alloys are used in applications requiring a combination of good mechanical properties and excellent resistance to corrosion. Despite prevalent industrial use, relatively few studies have been conducted to investigate the relationships between composition, solidification behavior, and microstructure. Given that these alloys are used in the cast and welded conditions, these factors have a significant influence over the material properties. Here, in this work, microstructural characterization, electron probe microanalysis, X-ray diffraction, and differential scanning calorimetry were used to study how changes in Si and Nb concentrations affected the solidification path and microstructure of Monel alloys. It was found that increasing Nb concentration stabilized higher amounts of MC carbides and suppressed graphite formation during solidification. It was also found that the high nominal concentration and segregation of Si to the liquid led to the formation of Ni 31 Si 12 and other silicides via terminal eutectic reactions at the end of solidification. A pseudo-binary solidification diagram was constructed using experimental data and was applied to predict the mass fraction of solidified eutectic as a function of composition. The modeled microstructures were found to be in good agreement with experimentally measured phase fractions.

36 MATERIALS SCIENCE↗