Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “matrix power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

In-pixel automatic threshold calibration for the CMS Endcap Timing Layer readout chip

We present the implementation and verification of an in-pixel automatic threshold calibration circuit for the CMS Endcap Timing Layer (ETL) in the High-Luminosity LHC upgrade. The discriminator threshold of the ETL readout chip (ETROC) needs to be calibrated regularly to mitigate the circuit baseline change. Traditional methods need a lot of communication through a slow control system hence are time-consuming. This paper describes an in-pixel automatic scheme with improvements in operating time and usability. In this scheme, a sample-accumulation circuit is used to measure the average discriminator output. A binary successive approximation and linear combination scan are applied to find the equivalent baseline. The actual calibration procedure has been first implemented in FPGA firmware and tested with the ETROC front-end prototype chip (ETROC0). The calibration circuit has been implemented with Triple Modular Redundancy (TMR) and verified with Single Event Effects (SEEs) simulation. A complete calibration process lasts 35 ms with a 40 MHz clock. In the worst case, the dynamic and static power consumption are estimated to be 300 uW and 10.4 uW, respectively. The circuit design, implemented in a 65 CMOS technology, will be integrated into ETROC2, the next iteration of the ETROC with a 16 x16 pixel matrix.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1979

High temperature solar thermal receiver

A design concept for a high temperature solar thermal receiver to operate at 3 atmospheres pressure and 2500 F outlet was developed. The performance and complexity of windowed matrix, tube-header, and extended surface receivers were evaluated. The windowed matrix receiver proved to offer substantial cost and performance benefits. An efficient and cost effective hardware design was evaluated for a receiver which can be readily interfaced to fuel and chemical processes or to heat engines for power generation.

Source record↗
NASA NTRS1980

Multiple scattering effects on wave propagation due to rain

The paper examines the multiple scattering of microwaves due to rain and the resulting incoherent intensity for a plane wave incident on a plane-parallel rain region. General formulations of the transfer equation using Stokes parameters are presented, and an extinction matrix which takes into account depolarization effects and nonspherical droplet shape is introduced. Scattering characteristics are calculated for spherical droplets using the Mie solution and the Laws-Parsons distributions. The ratios of incoherent to coherent received powers are calculated at 30 GHz for rain rates of 12.5, 50, 100, and 150 mm/h, rain thicknesses of 3 km and 10 km, and fields of view of 1.5, 5, and 15 deg.

Ishimaru, A.↗
DOE OSTI2021

Process for fabrication of enhanced β″-alumina solid electrolytes for energy storage devices and energy applications

A dense β″-alumina/zirconia composite solid electrolyte and process for fabrication are disclosed. The process allows fabrication at temperatures at or below 1600° C. The solid electrolytes include a dense composite matrix of β″-alumina and zirconia, and one or more transition metal oxides that aid the conversion and densification of precursor salts during sintering. The composite solid electrolytes find application in sodium energy storage devices and power-grid systems and devices for energy applications.

Lu, Xiaochuan↗
DOE OSTI2023

Computing rank‐revealing factorizations of matrices stored out‐of‐core

This paper describes efficient algorithms for computing rank-revealing factorizations of matrices that are too large to fit in main memory (RAM), and must instead be stored on slow external memory devices such as disks (out-of-core or out-of-memory). Traditional algorithms for computing rank-revealing factorizations (such as the column pivoted QR factorization and the singular value decomposition) are very communication intensive as they require many vector-vector and matrix-vector operations, which become prohibitively expensive when data is not in RAM. Randomization allows to reformulate new methods so that large contiguous blocks of the matrix are processed in bulk. The paper describes two distinct methods. The first is a blocked version of column pivoted Householder QR, organized as a “left-looking” method to minimize the number of the expensive write operations. The second method results employs a UTV factorization. It is organized as an algorithm-by-blocks to overlap computations and I/O operations. As it incorporates power iterations, it is much better at revealing the numerical rank. Numerical experiments on several computers demonstrate that the new algorithms are almost as fast when processing data stored on slow memory devices as traditional algorithms are for data stored in RAM.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Innovations in Sustainable Passive Wastewater Treatment - 20236

Sustainable water treatment systems, engineered to mimic natural processes and utilize natural materials, yield economic and environmental benefits through reductions in long term operational inputs, including: power, chemicals, and labor. Golder is an industry leader in the development and implementation of sustainable technologies at operating and closed mines. We continue to innovate these technologies and customize solutions to meet client needs by applying past experience and focused research. Sustainable (or passive) water treatment systems include ponds, wetlands, flow-through natural media beds, and limestone drains. These systems can blend in with a natural environment, are highly cost-effective for long-term water treatment, and can outcompete traditional active treatment technologies. Application of sustainable technologies relative to active technologies can be influenced by the influent water matrix, effluent limitations, flow rate of water requiring treatment, and available land area. In this presentation, four Golder-developed systems are reviewed as case studies, demonstrating our continued progressive approach to advancing sustainable water treatment technologies to meet industry needs. These case studies focus on design innovations and operational performance from data collected from the operational systems. Resources (power, chemicals, labor) required for the operation of each case study are compared with those that would be required for operation of their active treatment technology alternatives. - Case Study 1 presents an anaerobic biochemical reactor (BCR), a technology typically implemented for metals treatment and acid neutralization, for the treatment of sulfate to low concentrations (<250 mg/L). Active treatment via reverse osmosis (RO) membrane filtration is typically required for treatment of sulfate to similar concentrations, this innovation provides potential for sustainable treatment to replace the need for energy, chemical, labor, and waste (brine) intensive RO treatment for specific applications. Magnetite waste rock materials from the site were upcycled for use in this system to provide sequestration of the sulfide generated in the BCR. - Case Study 2 examines another novel application of the conventional BCR, modified for the removal of radionuclides and metals (uranium, radium, and selenium) at a closed uranium mine. - Case Study 3 presents implementation of sustainable treatment for mine drain water from a historic mine site, now a state park with around 100,000 visitors per year. The system includes a pond, wetland, and manganese removal bed surrounded by public trails designed to maintain the character of the park. The system treats for arsenic, iron, and manganese at relatively high flows (up to 1,200 gpm), with large seasonal fluctuations in flow and quality. - Case Study 4 is a unique project for which Golder is currently designing a sustainable treatment system, with no energy input, to treat nitrate in mine water post-closure at a site near the arctic circle. In this unprecedented application, climate, management of freshet, and space availability presented substantial technical challenges. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Harmonic Modeling, Data Generation and Analysis of Power Electronics-Interfaced Residential Loads

The share of electronics-based residential load is expected to rise as devices such as variable frequency drives (VFDs), electric vehicle chargers, and inverter-based distributed energy resources (DERs), e.g., photovoltaic (PV) systems become more common. These loads may introduce significant harmonics into power networks that need to be closely studied in order to perform accurate load modeling and forecasting. However, it can be difficult to obtain harmonic-rich voltage and current data - necessary for identifying accurate load models - for residential electrical loads. Recognizing this need, we identify and model a set of electronics-based end-use loads and DERs in an electromagnetic transients program (EMTP) tool for a residence with a single- phase split-phase supply. Further, a procedure is developed to model harmonic interactions between end-use loads connected to the same non-ideal supply voltage in a residential setting. Finally, a harmonic-rich dataset produced via the proposed procedure is utilized to identify frequency coupling matrix (FCM) based load model. Numerical results demonstrate the accuracy of the model, and explore model identifiability with limited data points.

harmonics, power quality, load modeling↗
DOE OSTI2020

Hierarchical morphologies in co-sputter deposited thin films

Co-depositions of immiscible alloy films at specific processing conditions have yielded hierarchical microstructures which consist of distinct features at multiple length scales, often agglomerates and concentration modulations on the sub-micrometer-scale and fine nanoprecipitates in a matrix on the nanoscale. The present work examined a series of immiscible alloy systems: Cu-Mo, Cu-Ag, Cu-Fe, Cu-Ta, Mo-Ag, Cu-Mo-Ag, to determine the kinetic conditions favorable for hierarchical organization and the formation mechanism of such structures. Thin films of six immiscible systems were sputter co-deposited over a range of deposition rates from 0.12 to 2 nm/s and various temperatures from 400 to 800°C. The resulting microstructures indicate that hierarchical structures form with sufficient disparity in kinetic energy between the constituent atoms, one species being highly mobile (A) and the other relatively immobile (B). This condition arises typically at elevated deposition temperatures and reduced deposition rates but is also alloy dependent. The hierarchical structures form during deposition via phase separation and self-organization processes across the multiple length scales. The adatoms diffuse on the film surface with the highly mobile species swiftly agglomerating into A-rich domains within which B-rich nanoprecipitates form, often self-organizing into periodic arrays. The smallest B-rich nanoprecipitates in the A-rich domains are found to be coherent and in a metastable crystal structure (B taking the structure of A), but coarser precipitates that exhibit the equilibrium structure of B element. The A-rich domains are surrounded by a B-rich matrix that phase-separates into a concentration modulated structure. In conclusion, the observations are interpreted via a model incorporating material properties and process parameters.

36 MATERIALS SCIENCE↗
NASA NTRS1994

Higher harmonic control analysis for vibration reduction of helicopter rotor systems

An advanced higher harmonic control (HHC) analysis has been developed and applied to investigate its effect on vibration reduction levels, blade and control system fatigue loads, rotor performance, and power requirements of servo-actuators. The analysis is based on a finite element method in space and time. A nonlinear time domain unsteady aerodynamic model, based on the indicial response formulation, is used to calculate the airloads. The rotor induced inflow is computed using a free wake model. The vehicle trim controls and blade steady responses are solved as one coupled solution using a modified Newton method. A linear frequency-domain quasi-steady transfer matrix is used to relate the harmonics of the vibratory hub loads to the harmonics of the HHC inputs. Optimal HHC is calculated from the minimization of the vibratory hub loads expressed in term of a quadratic performance index. Predicted vibratory hub shears are correlated with wind tunnel data. The fixed-gain HHC controller suppresses completely the vibratory hub shears for most of steady or quasi-steady flight conditions. HHC actuator amplitudes and power increase significantly at high forward speeds (above 100 knots). Due to the applied HHC, the blade torsional stresses and control loads are increased substantially. For flight conditions where the blades are stalled considerably, the HHC input-output model is quite nonlinear. For such cases, the adaptive-gain controller is effective in suppressing vibratory hub loads, even though HHC may actually increase stall areas on the rotor disk. The fixed-gain controller performs poorly for such flight conditions. Comparison study of different rotor systems indicates that a soft-inplane hingeless rotor requires less actuator power at high speeds (above 130 knots) than an articulated rotor, and a stiff-inplane hingeless rotor generally requires more actuator power than an articulated or a soft-inplane hingeless rotor. Parametric studies for a hingeless rotor operating in a transition flight regime and for an articulated rotor operating at the level-flight boundary (high speed and high thrust conditions) indicate that blade parameters including flap, lag, torsion stiffness distributions, linear pretwist, chordwise offset of center-of-mass from elastic axis and chordwise offset of elastic axis from aerodynamic center can be selected to minimize the actuator power requirements for HHC.

Nguyen, Khanh Q.↗
DOE OSTI2025

Quantum entropy as a harbinger of factorizability

Deeply inelastic scattering (DIS) is a powerful probe for investigating the QCD structure of hadronic matter and testing the standard model (SM). DIS can be described through QCD factorization theorems which separate contributions to the scattering interaction arising from disparate scales — e.g ., with nonperturbative matrix elements associated with long distances and a perturbative hard scattering kernel applying to short-distance parton-level interactions. The fundamental underpinnings of factorization may be recast in the quantum-theoretic terms of entanglement, (de)coherence, and system localization in a fashion which sheds complementary light on the dynamics at work in DIS from QCD bound states. In this Letter, we propose and quantitatively test such a quantum-information theoretic approach for dissecting factorization in DIS and its domain of validity; we employ metrics associated with quantum entanglement such as a differential quantum entropy and associated Kullback-Leibler (KL) divergences in numerical tests. We deploy these methods on an archetypal quark-spectator model of the proton, for which we monitor quantum decoherence in DIS as underlying model parameters are varied. On this basis, we demonstrate quantitatively how factorization-breaking effects may be imprinted on quantum entropies in a kinematic regime where leading-twist factorization increasingly receives large corrections from finite- Q 2 effects; our findings suggest potential applications of quantum simulation to QCD systems and their interactions.

Deep inelastic scattering↗
DOE OSTI2025

SymProp: Scaling Sparse Symmetric Tucker Decomposition via Symmetry Propagation

Sparse symmetric tensors are an important class of tensors, and their decompositions serve as powerful tools for revealing low-rank structures. This paper introduces SymProp, a novel approach for scaling sparse symmetric Tucker decomposition by propagating symmetry through intermediate computations. SymProp optimizes two key computational kernels: Sparse Symmetric Tensor Times Same Matrix chain (S3 TTMc) for Higher-Order Orthogonal Iteration (HOOI) and Sparse Symmetric Tensor Times Same Matrix chain Times Core (S3 TTMcTC) for Higher-Order QR Iteration (HOQRI). Our method employs a metaprogramming-based index iteration approach to efficiently handle the upper triangular parts of intermediate dense symmetric tensors. SymProp achieves up to 50.9× speedup over SPLATT and up to 360.8× over Compressed Sparse Symmetric (CSS) format on the S3 TTMc operation. Moreover, our S3 TTMc and S3 TTMcTC implementations support tensor orders four levels higher than state-of-the-art methods. Our HOQRI demonstrates superior scalability and up to a 33.6× speedup over optimized HOOI. By enabling more scalable Tucker decompositions for higher orders, decomposition ranks, and dimension sizes, SymProp opens new possibilities for analyzing complex hypergraph structures in fields such as network science, data mining, and machine learning.

Li, Zecheng [North Carolina State University]↗
DOE OSTI2022

The DUNE Photon Detection System

DUNE is an underground neutrino oscillation experiment that will be performing precision measurements of the PMNS matrix to determine unambiguously the mass ordering and the leptonic CP violation. It also comprises a rich non-accelerator physics program for the detection of supernova neutrinos, nucleon decay, and BSM physics. DUNE employs a high-power neutrino beam under construction at Fermilab together with the DUNE Near Detector, and four liquid argon TPCs (Far Detector) that will be installed at the Sanford Underground Research Facility in South Dakota, 1300 km away from the neutrino source. The photon detection system (PDS) – which records the 128 nm scintillation light of argon and provides the time of interaction of the beam neutrinos in the Far Detector - is critical for studying nucleon decay and detecting Supernova Neutrino Bursts. The PDS also complements the calorimetric measurement performed by the TPC (i.e. the charge readout) and contributes to the energy calibration and time performance of the Far Detector. The article is an overview of the design of the PDS for the first DUNE far detector module, with special emphasis on VUV light trapping in a cryogenic environment, its technical challenges, and the expected physics performance. The status of the construction of the PDS and its validation in the Run II of ProtoDUNE-SP will be also presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1982

An optimization technique for lumped-distributed two ports

A frequency domain direct efficient analysis and an optimization technique of a large class of lumped-distributed networks containing active elements are presented. Sensitivity and Hessian matrix calculations are performed using truncated Taylor series expansion of two-port parameters of subnetworks. An interactive computer program was developed to demonstrate the application of the method. Examples of network optimizations are included to illustrate the powerfulness of the technique.

Iobst, K. W.↗
NASA NTRS1988

A spatial operator algebra for manipulator modeling and control

A powerful new spatial operator algebra for modeling, control, and trajectory design of manipulators is discussed along with its implementation in the Ada programming language. Applications of this algebra to robotics include an operator representation of the manipulator Jacobian matrix; the robot dynamical equations formulated in terms of the spatial algebra, showing the complete equivalence between the recursive Newton-Euler formulations to robot dynamics; the operator factorization and inversion of the manipulator mass matrix which immediately results in O(N) recursive forward dynamics algorithms; the joint accelerations of a manipulator due to a tip contact force; the recursive computation of the equivalent mass matrix as seen at the tip of a manipulator; and recursive forward dynamics of a closed chain system. Finally, additional applications and current research involving the use of the spatial operator algebra are discussed in general terms.

Rodriguez, G.↗
NASA NTRS1990

Optical information processing for NASA's space exploration

The development status of optical processing techniques under development at NASA-JPL, NASA-Ames, and NASA-Johnson, is evaluated with a view to their potential applications in future NASA planetary exploration missions. It is projected that such optical processing systems can yield major reductions in mass, volume, and power requirements relative to exclusively electronic systems of comparable processing capabilities. Attention is given to high-order neural networks for distortion-invariant classification and pattern recognition, multispectral imaging using an acoustooptic tunable filter, and an optical matrix processor for control problems.

Chao, Tien-Hsin↗
NASA NTRS1993

Intensity and polarization of light scattered by size distributions of randomly oriented nonspherical particles

Calculations of light scattering by small particles are important in many diverse fields of science and engineering. In many cases of practical interest, scattering particles are nonspherical and are distributed over sizes and orientations. However, accurate light scattering computations for ensembles of nonspherical particles are difficult and time-consuming, and the literature in which such calculations are reported is rather scarce. In this paper, the T-matrix approach, as extended recently to randomly oriented particles, is used to calculate rigorously light scattering by size distributions of randomly oriented axially symmetric particles. To model the variation of particle sizes in real ensembles, we use a power law distribution typical of some terrestrial aerosols. Contour plots of intensity and degree of linear polarization for polydisperse prolate and oblate spheroids of different aspect ratios and effective equivalent-sphere size parameters from 0 to 10 are calculated and compared with calculations for equivalent spheres. The angular scattering behavior of nonspherical polydispersions is found to be greatly different from that of spheres, while the scattering properties of oblate and prolate spheroids of the same aspect ratio are similar. With increasing particle size, both intensity and polarization become more shape-dependent. In general, nonspherical particles are stronger side scatterers and weaker backscatterers than equivalent spheres. With increasing aspect ratio of nonspherical particles polarization tends to be predominantly positive. Possible effects of particle nonsphericity on optical remote sensing of atmospheric aerosols are discussed.

Mishchenko, M. I.↗
NASA NTRS1993

Optical information processing at NASA Ames Research Center

The combination of analog optical processors with digital electronic systems offers the potential of tera-OPS computational performance, while often requiring less power and weight relative to all-digital systems. NASA is working to develop and demonstrate optical processing techniques for on-board, real time science and mission applications. Current research areas and applications under investigation include optical matrix processing for space structure vibration control and the analysis of Space Shuttle Main Engine plume spectra, optical correlation-based autonomous vision for robotic vehicles, analog computation for robotic path planning, free-space optical interconnections for information transfer within digital electronic computers, and multiplexed arrays of fiber optic interferometric sensors for acoustic and vibration measurements.

Reid, Max B.↗