Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials aging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

A Comparison of Tension and Compression Creep in a Polymeric Composite and the Effects of Physical Aging on Creep Behavior

Experimental and analytical methods were used to investigate the similarities and differences of the effects of physical aging on creep compliance of IM7/K3B composite loaded in tension and compression. Two matrix dominated loading modes, shear and transverse, were investigated for two load cases, tension and compression. The tests, run over a range of sub-glass transition temperatures, provided material constants, material master curves and aging related parameters. Comparing results from the short-term data indicated that although trends in the data with respect to aging time and aging temperature are similar, differences exist due to load direction and mode. The analytical model used for predicting long-term behavior using short-term data as input worked equally as well for the tension or compression loaded cases. Comparison of the loading modes indicated that the predictive model provided more accurate long term predictions for the shear mode as compared to the transverse mode. Parametric studies showed the usefulness of the predictive model as a tool for investigating long-term performance and compliance acceleration due to temperature.

Gates, Thomas S.↗

VERA-Grizzly Ex-Core Calculations: Watts Bar Unit 1 Cycles 1-2

The critical structures that comprise light-water reactor (LWR) nuclear power plants are subjected to operating environments that can challenge their integrity. Structures in close proximity to the reactor core, such as the reactor pressure vessel (RPV) and the biological shield wall, are subjected to high levels of radiation emanating from the core, as well as elevated temperatures. As the US fleet of operating LWRs ages, the effects of these operating environments on the integrity of these structures must be considered to ensure their continued safe operation. Extending the lifetime of commercial reactors and maintaining the aging reactor fleet require accurate prediction of the exposure of ex-core components to neutron and photon radiation. In particular, concrete degradation studies must be performed to evaluate the safety and long-term operation of reactors with lifetime extensions. The concrete reactor bioshield is important for providing radiological protection during operation and must last for the entire lifetime of the reactor. Recent interest in lifetime extensions furthers the need to accurately simulate concrete material degradation in the reactor bioshield. As a result of this need, the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has funded this study to couple its tools, Virtual Environment for Reactor Applications (VERA) and Grizzly. VERA allows users to set up models to calculate time-dependent and fully coupled solutions (with thermal feedback) for ex-core quantities of interest such as vessel and coupon fluence and detector responses for multiple statepoints and cycles. Grizzly is a finite-element application based on the Multiphysics Object Oriented Simulation Environment (MOOSE) framework that is used to enable aging materials calculations. This report highlights the work performed to calculate the fluence in the vessel and concrete for Watts Bar Nuclear Plant Unit 1 (WBN1) Cycles 1 and 2. The fluences obtained from VERA were successfully transferred to Grizzly using a Python script. Four simulations were run with Grizzly: (1) the Mazars model with the initial Young’s modulus being the instantaneous modulus, (2) the Mazars model with the initial Young’s modulus being the delayed modulus, (3) the Mazars model with the initial Young’s modulus being the delayed modulus with the addition of the effects of micro-damage caused by irradiation, and (4) the Mazars model with the initial Young’s modulus being the instantaneous modulus, and with the addition of micro-damage and creep. Details regarding the methods used to obtain the fluence and the statistical errors associated with the VERA Monte Carlo Shift calculations are discussed in greater detail in this report. The results obtained from the four Grizzly models are also presented in this report.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Influence of coarsened and rafted microstructures on the thermomechanical fatigue of a Ni-base superalloy

The aging of the microstructure of Ni-base superalloys during service is mainly characterized by coarsening and rafting of the γ' precipitates. The influence of these different aged microstructures on thermomechanical fatigue (TMF) under either continuously cycled (CC) and creep-fatigue (CF) was investigated. Three different aged microstructures, generated through accelerated aging and pre-creep treatments, were studied: stress-free coarsened γ', rafted with orientation perpendicular to loading direction (N-raft), and rafted with orientation parallel to loading direction (P-raft). Under most conditions, the aged microstructures were less resistant to TMF than the virgin microstructure; however, there were exceptions. Both stress-free coarsened and N-raft microstructures resulted in a reduction in TMF life under both CC and CF conditions in comparison to the virgin material. P-raft microstructure also resulted in reduction in TMF life under CC conditions; however, an increase in life over that of the virgin material was observed under CF conditions. Finally, these differences are discussed and hypothesized to be related to the interactions of the dislocations in the γ channels with γ' precipitates.

36 MATERIALS SCIENCE↗

Consortium breccia 73255 - Laser /Ar-39/-/Ar-40/ dating of aphanite samples

Laser (Ar-39)-(Ar-40) studies of clasts and groundmass in breccia 73255 are presented. They show a variety of ages indicating that some materials lost argon from sites that outgas at low temperature, while other materials have retained argon generated before the breccia-forming event. The estimate for the time of the breccia-forming event from thermal release studies is compared to the upper limit of the event from the laser studies; this work also shows that ages in excess of 4.0 G.y. determined on rocks containing devitrified maskelynite clasts probably have no chronological significance.

Eichhorn, G.↗

Evaluation of microstructural damage and alteration of polytypes to determine the aging of silicon carbide

Irradiated silicon carbide (SiC) exhibits higher carrier content but a decrease in conductivity with increased irradiation. It was theorized that this conflicting data was due to structural damage due to irradiation. This theory was supported by the fact that non-irradiated 50{mu}m thick SiC is transparent for visible light and the higher the irradiation dose, the material of the same thickness became less transparent. However, changes in microscopy and polyforms observed by transmission electron microscopy in SiC due to irradiation were minor. Although existence of different polymorphs of SiC was documented, direct proof of the proposed theory has not yet been achieved.

36 MATERIALS SCIENCE↗

Dynamic measurements of ultraviolet-enhanced silica contamination by photoluminescence-based diagnostic

The ultraviolet-enhanced (UV-enhanced) contamination of optical components leads to an untimely aging of sealed laser systems, photolithography, and synchrotron installations. The laser-induced deposition of organic films on silica substrates and coatings significantly reduces their transmission and degrades their optical functions. In this paper, measurements of organic contaminant films growth under 213 nm laser irradiation performed on silica Corning 7980 grade ArF are reported. We present an in situ contaminant layer growth diagnostic based on silica photoluminescence measurements. The purpose was to determine the photodeposition kinetics as a function of controlled environmental conditions and fluence and to find out the experimental conditions in which the growth of contamination films was significantly reduced. We then demonstrated that with a low partial pressure of oxygen, the growth of carbonaceous films is drastically reduced during UV laser irradiation whereas with water and nitrogen it was not the case. We also proposed a physical modeling of the UV-enhanced silica contamination processes.

36 MATERIALS SCIENCE↗

Structural development of Coprates Chasma and western Ophir Planum, Valles Marineris Rift, Mars

A portion of Valles Marineris was mapped in detail in order to clarify the dominant processes responsible for the formation of Coprates Chasma. New crater counts indicate that the caprock on western Ophir Planum plateau has a Late Hesperian crater age, whereas trough floor preserved in western Coprates Chasma has an Early to Late Hesperian crater age. Caprock on western Ophir Planum correlates in relative age with the Syria Planum Formation, and the caprock may overlie Lower Hesperian ridged plains material. Trough floor material in Coprates Chasma correlates in relative age with ridged plains material on the adjacent Lunae Planum and Coprates plateaus and represents a structurally coherent block displaced downward by normal faulting. The crater counts and detailed structural relationships demonstrate the commonly accepted view that Coprates Chasma occupies a graben. Formation of Coprates Chasma by keystone collapse of locally elevated topography is not supported by available topographic data, but a general association between the trough and volcanotectonic activity in the Tharsis region is considered to be a likely explanation for the trough forming stresses. Faulting on Ophir Planum appears related to the faulting that created the Coprates Chasma trough. The geology and structure of Coprates Chasma are comparable to those of other troughs such as Melas, Ius, and perhaps Candor chasmata, suggesting that these troughs may also have formed as grabens.

Schultz, Richard A.↗

Precipitation behavior of Widmanstätten O phase associated with interface in aged Ti2AlNb-based alloys

Highlights: • Ball milling tunes the morphology of primary O phase in Ti{sub 2}AlNb alloys. • The interface of Widmanstatten B2 and O affects the hardness of the alloys. • The entire precipitation process of Widmanstatten O phase is reported. - Abstract: Ti{sub 2}AlNb-based alloys, spark plasma sintered from ball-milled octahedral Ti-22Al-25Nb powder, are aged for 0–3 h in this study. Ball milling tunes the morphology of primary orthorhombic (O) phase to be columnar, and improves the mechanical properties of the alloys. The evolution of the Widmanstätten O phase, which brought main precipitation strengthening effect, is then investigated during the ageing process. The hardness of the alloys is improved by an increasing content of O phase and the reduced width of the Widmanstätten O phase; in addition, the length of Widmanstätten O phase also brings positive effect on the hardness, which indicates that the hardness is strongly coupled with the interface of the Widmanstätten O precipitates and B2 matrix. By means of transmission electron microscopy observation, the precipitation of O initials with an amorphous state, followed by a coherent interface between (110){sub B2} and (002){sub O}, which is destroyed to be semi-coherent and incoherent during the next ageing stage.

36 MATERIALS SCIENCE↗

Gamma Radiation Effects on Physical, Optical, and Structural Properties of Binary As-S glasses

Gamma radiation induces changes in physical, optical, and structural properties in chalcogenide glasses., Previous research has focused on As{sub 2}S{sub 3} and families of glasses containing Ge. For the first time, we present composition and dose dependent data on the As-S binary glass series. Binary As{sub x}S{sub 100-x} (x = 30, 33, 36, 40, and 42) glasses were irradiated with gamma radiation using a {sup 60}Co source at 2.8 Gy/s to accumulated doses of 1, 2, 3, and 4 MGy. The irradiated samples were characterized at each dose level for density, refractive index, x-ray diffraction, and Raman spectrum. These results are compared to those of as-made and 1 year aged samples. We report an initial increase in density followed by a decrease as a function of dose that contradicts the expected compositional dependence of molar volume of these glasses. This unusual behavior is explained based on microvoid formation and nanoscale phase-separation induced by the irradiation in these glasses. XRD, Raman, and EPR data provide supporting evidence, underscoring the importance of optimally- or overly-constrained structures for stability under aging or irradiation.

36 MATERIALS SCIENCE↗

Wear Measurement of Highly Cross-linked UHMWPE using a 7 Be Tracer Implantation Technique

The very low wear rates achieved with the current highly cross-linked ultrahigh molecular weight polyethylenes (UHMWPE) used in joint prostheses have proven to be difficult to measure accurately by gravimetry. Tracer methods are there- fore being explored. The purpose of this study was to perform a proof-of-concept experiment on the use of the radioactive tracer beryllium-7 (7Be) for the determination of in vitro wear in a highly cross-linked orthopedic UHMWPE. Three cross-linked and four conventional UHMWPE pins made from compression- molded GUR 1050, were activated with 109 to 1010 7Be nuclei using a new implantation setup that produced a homogenous distribution of implanted nuclei up to 8.5 lm below the surface. The pins were tested for wear in a six-station pin-on-flat appara- tus for up to 7.1 million cycles (178 km). A Germanium gamma detector was employed to determine activity loss of the UHMWPE pins at preset intervals during the wear test. The wear of the cross-linked UHMWPE pins was readily detected and esti- mated to be 17 6 3 lg per million cycles. The conventional-to- cross-linked ratio of the wear rates was 13.1 6 0.8, in the expected range for these materials. Oxidative degradation dam- age from implantation was negligible; however, a weak depend- ence of wear on implantation dose was observed limiting the number of radioactive tracer atoms that can be introduced. Future applications of this tracer technology may include the analysis of location-specific wear, such as loss of material in the post or backside of a tibial insert.

cross-linked↗

The Effect of Melt Ultrasound Treatment on the Microstructure and Age Hardenability of Al-4 Wt Pct Cu/TiC Composite

In the present work, Al-4 wt pct Cu/TiC composite was synthesized by the molten salt route that contains submicron-sized TiC particles in the Al-4 wt pct Cu matrix. The concentration of the TiC particle in the base alloy is 7.5 wt pct. Melt ultrasound treatment was done by remelting the as-cast composite at 1023 K (750 °C) in a view to refine the size of TiC particles to nanoscale and distribute them evenly in the matrix. The microstructure and age hardenability of the untreated and ultrasound-treated composites were investigated. The TiC particles accelerate the precipitation kinetics of CuAl{sub 2} phase in Al-4 wt pct Cu alloy. In the present study, the hardness obtained for untreated Al-4 wt pct Cu/TiC composite is 120 VHN within 5 hours of peak aging time, which is higher than the hardness of the monolithic Al-4 wt pct Cu, which is 104 VHN at 35 hours of peak aging time. Melt ultrasound treatment of Al-4 wt pct Cu/TiC composite shows no significant effect on the distribution and refinement of TiC particles in the matrix. However, it partially disintegrates the TiC into Al{sub 3}Ti and Al{sub 4}C{sub 3} particles. The ultrasound-treated composite showed an improved hardness of about 132 VHN at 5 hours of peak aging, in comparison to that of the untreated composite, by forming denser and homogeneous CuAl{sub 2} precipitates.

36 MATERIALS SCIENCE↗

Microstructural Characterization and Electrochemical Behavior of AA2014 Al-Cu-Mg-Si Alloy of Various Tempers

AA2014 Al-Cu-Mg-Si alloy is subjected to aging heat treatment, and microstructural features and electrochemical behavior of the AA2014 Al-Cu-Mg-Si alloy of various tempers have been characterized. Hardness measurement of the alloy of different tempers showed typical age hardening behavior. X-ray diffraction and transmission electron microscopy studies revealed the presence of characteristic phases. Differential scanning calorimetry study displayed the sequence of solid-state precipitation and dissolution reactions in the AA2014 alloy of various tempers. Electrochemical behavior was assessed by measurement of variation of open-circuit voltage with time, potentiodynamic polarization and potentiodynamic cyclic polarization of the AA2014 alloy of various tempers in 3.5 wt.% NaCl solution at near neural (pH ~ 7) and at alkaline (pH 12) conditions. Potentiodynamic polarization studies of different tempers in 3.5 wt.% NaCl solution at pH ~ 7 showed that the corrosion potential (E{sub corr}) value has shifted toward more negative (active) direction with increasing aging time. The cyclic polarization in 3.5 wt.% NaCl solution at pH ~ 7 displayed active–passive behavior and also showed a large hysteresis loop indicating high pit growth damage.

36 MATERIALS SCIENCE↗

Microstructural evolution and mechanical properties of maraging steel produced by wire + arc additive manufacture process

Highlights: • Wire + arc additive manufacture (WAAM) was applied to produce maraging steel structures. • Microstructure evolution of WAAM alloy was characterized and correlated with the layer-by-layer building manner. • Mechanical properties of WAAM alloy were tested and correlated with the aging response of WAAM microstructure. • Retained austenite content was measured and correlated with the tensile strength loss. - Abstract: Wire + arc additive manufacture is developed for producing large-scale metallic components. In this paper, maraging steel parts were produced, and the microstructure and mechanical properties were investigated. The microhardness and tensile strength of the as deposited alloy reduced from the bottom to the top due to the transient thermal cycling, which resulted in partial aging and non-uniform formation of intermetallic compounds along the building direction. Solutionizing, followed by 3 h aging, significantly reduced the microstructural heterogeneity and increased the mechanical properties by 24.7% through the formation of large amounts of finely distributed precipitates. The as deposited alloy possessed superior strength to the wrought alloy in solutionized condition but inferior to the later in aged condition, which was attributed to the less pronounced aging response of the low-angle columnar grains characterized microstructure and the presence of retained and reverted austenite.

36 MATERIALS SCIENCE↗

Precipitation behavior of α phase during aging treatment in a β-quenched Ti-7333

Highlights: • The precipitation behaviors of α precipitate are investigated in the hot-rolled Ti-7333. • The formation of the V-shaped α configuration is closely related to the variant selection of α phase. • The angle between the closely packed direction of α{sub GB} and GB plane plays a key role on the precipitation of α{sub GB}. - Abstract: In this work, the precipitation behavior of α phase during the isothermal aging treatment was investigated in the β-quenched Ti-7333. The results indicate that dislocations contribute to the precipitation of α phase with a dot-like morphology at the beginning of aging treatment, and these dot-like α precipitates holding the same Burgers orientation relationship (BOR) with respect to the β matrix coalesce into the platelet morphology. The platelet-like α precipitates that orientate to different growth directions combine with each other to form the V-shaped configuration. And the formation of this configuration is closely related with the variant selection (VS) of α phase, which is resulted from the perfect accommodation of transformation strain within the β matrix. Meanwhile, it is found that low-angle grain boundaries (LAGBs) and high-angle grain boundaries (HAGBs) can be decorated by α phase during the aging treatment, and its precipitation degree significantly depends on the angle between the closely packed direction of αGB and the GB plane. The volume fraction of α phase increases with increasing aging time, and this increasing volume fraction eventually results in the increase in micro-hardness of the alloy.

36 MATERIALS SCIENCE↗

Influence of duplex ageing on secondary α precipitates and mechanical properties of the near β-Ti alloy Ti-55531

Highlights: • High strength β-Ti alloys are widely used for their excellent properties. • To reach an excellent combination of strength and ductility, it is attractive to explore the right heat treatment system. • While compared to the conventional single-step ageing process, duplex ageing could change the development and refinement of secondary α precipitations in near/metastable β-Ti alloys resulting varying in performance. • Therefore it is of scientific significance and engineering value to understand the influence of duplex ageing on the formation of secondary α precipitates and mechanical properties for this type of alloy. - Abstract: This paper presents the results of studies on the microstructure and mechanical properties of a near β-Ti alloy processed with different ageing approaches. Influences of intragranular ultrafine α precipitates and grain boundary α layer on mechanical properties in Ti-55531 alloy were analyzed. The results indicate that the precipitation microstructure of the duplex aged alloy exhibits a uniform size and acicular α precipitated orientation shows an angle of approximately 60°. While the morphology of secondary α precipitates in single-step aged samples appear the irregular distribution and heterogeneous size. With the final ageing time increasing, the morphology of intragranular α precipitates and grain boundary α phase brings out a distinct coarsening. The single-step aged alloy can yield a better combination of the ultimate tensile strength (1265 MPa) and ductility (9%). However, the ultimate tensile strength of the duplex aged alloy even reaches 1368 MPa but it breaks at the stage of elastic deformation. The fracture mode of Ti-55531 alloy changes from predominantly dimple fracture in single-step aged samples to predominantly faceted and cleavage type fracture in duplex aged samples causing by the differences of intragranular α precipitates and the interface between grain boundary α layer and intragranular microstructure.

36 MATERIALS SCIENCE↗

Slow Aging Dynamics and Avalanches in a Gold-Cadmium Alloy Investigated by X-Ray Photon Correlation Spectroscopy

Results of a x-ray photon correlation spectroscopy experiment on the very weakly first order martensitic transformation of a Au{sub 50.5}Cd{sub 49.5} single crystal are presented. Slow non-equilibrium-dynamics are observed in a narrow temperature interval in the direct vicinity of the otherwise athermal phase transformation. These dynamics are associated with the martensite-aging effect. The dynamical aging is accompanied by an avalanchelike behavior which is identified with an incubation-time phenomenon.

36 MATERIALS SCIENCE↗

Stress breaks universal aging behavior in a metallic glass

Numerous disordered materials display a monotonous slowing down in their internal dynamics with age. In the case of metallic glasses, this general behavior across different temperatures and alloys has been used to establish an empirical universal superposition principle of time, waiting time, and temperature. Here we demonstrate that the application of a mechanical stress within the elastic regime breaks this universality. Using in-situ x-ray photon correlation spectroscopy (XPCS) experiments, we show that strong fluctuations between slow and fast structural dynamics exist, and that these generally exhibit larger relaxation times than in the unstressed case. On average, relaxation times increase with stress magnitude, and even preloading times of several days do not exhaust the structural dynamics under load. A model Lennard-Jones glass under shear deformation replicates many of the features revealed with XPCS, indicating that local and heterogeneous microplastic events can cause the strongly non-monotonous spectrum of relaxation times.

36 MATERIALS SCIENCE↗

Variations in the output characteristics of broadband superluminescent diodes during long-term operation

A method of service life tests of SLD-37 quantum-well superluminescent diodes (SLDs), which are widely used in optical coherence tomography, is described and the results of tests are presented. Special attention is given to variations in the emission spectra of SLDs during their aging. It is shown that this method can be used as an incoming test to select processed semiconductor heterostructures with the longest expected lifetime for fabrication of active elements of SLD modules. (lasers)

36 MATERIALS SCIENCE↗