Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “literature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Flow pattern and void fraction characterization in nitrogen/water flows through a diamond-type triply periodic minimal surface lattice

Here, this study presents, to the authors knowledge, the first experimental investigation on the void fraction and flow patterns in two-phase flows through a diamond-type Triply Periodic Minimal Surface (TPMS) lattice. An additively manufactured TPMS structure was tested under upward co-current flow of a water/nitrogen mixture. Superficial velocities varied for a total of 42 test conditions (gas: 0.01–2.4 m/s; liquid: 0.01–2.4 m/s; mass flux: 20–2370 kg/m 2 ·s). High-speed video and X-ray imaging enabled time-averaged void fraction measurements and identified six distinct flow regimes which were used to develop a flow pattern map. Comparison of the void fraction data with correlations from literature demonstrated the Rouhani and Axelsson (1970) [49] correlation modified by Steiner (1993) [52] provided the best agreement, which was improved with empirically fit coefficients. This approach predicted the void fraction with errors < ±20% for 64% of the data, with a mean absolute percent deviation (MAPD) of 23%. The measured frictional pressure drop was compared to correlations from literature which captured the observed trends but did not provide good accuracy. The best agreement was found after optimizing the empirical coefficients of the Muller-Steinhagen & Heck (1986) [56] correlation; this approach captured 33% of the data within ±20% with a MAPD of 46% over the full range and captured 71% of the data within ±20% a MAPD of 13.3% at mass fluxes >1100 kg/m 2 -s. These results provide foundational insight into TPMS two-phase flow behavior and inform modeling and design of advanced heat exchange components incorporating TPMS geometries.

42 - ENGINEERING↗
DOE OSTI2020

A review of select human-building interfaces and their relationship to human behavior, energy use and occupant comfort

In recent years, research has emerged to quantitatively and qualitatively understand occupants' interactions with buildings. However, there has been surprisingly little research on building interfaces and how their design, context (e.g., location), and underlying logic impact their usability and occupants’ perceived control, as well as the resulting comfort and energy performance. This means that research is needed to better understand how occupants interact with building interfaces in both commercial and residential applications; both applications are important to address as there are many differences in interface types, level of control and understanding, and even expectations of engagement. Herein, this paper provides a cursory review and discussion of select common building interfaces: windows, window shades/blinds, thermostats, and lighting controls. The goal of this paper is to review literature related to these human-building interfaces to explore interface characteristics, current design and use challenges, and relationships between building interfaces and occupants. Human-building interface interactions are complex, more research is needed to understand design, use, and characteristics. Common themes emerged throughout the literature review to explain occupant interactions (or lack of interactions) with building interfaces, which included thermal and visual comfort, ease and access of control, interface/control placement, poor interface/control design, lack of understanding, and social-behavioral dynamics.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

A guideline to document occupant behavior models for advanced building controls

The availability of computational power, and a wealth of data from sensors have boosted the development of model-based predictive control for smart and effective control of advanced buildings in the last decade. More recently occupant-behavior models have been developed for including people in the building control loops. However, while important objectives of scientific research are reproducibility and replicability of results, not all information is available from published documents. Therefore, the aim of this paper is to propose a guideline for a thorough and standardized occupant-behavior model documentation. For that purpose, the literature screening for the existing occupant behavior models in building control was conducted, and the occupant behavior modeling processes were studied to extract practices and gaps for each of the following phases: problem statement, data collection, and preprocessing, model development, model evaluation, and model implementation. Here, the literature screening pointed out that the current state-of-the-art on model documentation shows little unification, which poses a particular burden for the model application and replication in field studies. In addition to the standardized model documentation, this work presented a model-evaluation schema that enabled benchmarking of different models in field settings as well as the recommendations on how OB models are integrated with the building system.

Building control↗
DOE OSTI2022

Modeling the thermodynamics of the FeTi hydrogenation under para-equilibrium: An ab-initio and experimental study

We report FeTi-based hydrides have recently re-attracted attention as stationary hydrogen storage materials due to favorable reversibility, good sorption kinetics and relatively low costs compared to alternative intermetallic hydrides. Employing the OpenCalphad software, the thermodynamics of the (FeTi) 1-x H x (0 ≤ x ≤ 1) system were assessed as a key basis for modeling hydrogenation of FeTi-based alloys. New thermodynamic data were acquired from our experimental pressure-composition-isotherm (PCI) curves, as well as first-principles calculations utilizing density functional theory (DFT). The thermodynamic phase models were carefully selected based on critical analysis of literature information and ab-initio investigations. Key thermodynamic properties such as dissociation pressure, formation enthalpies and phase diagrams were calculated in good agreement to our performed experiments and literature-reported data. This work provides an initial perspective, which can be extended to account for higher-order thermodynamic assessments and subsequently enables the design of novel FeTi-based hydrides. In addition, the assessed thermodynamic data can serve as key inputs for kinetic models and hydride microstructure simulations.

08 HYDROGEN↗
DOE OSTI2020

Metal–organic frameworks based on multicarboxylate linkers

When designing metal–organic frameworks (MOFs), linker design is one of the most important factors in constructing a wide variety of structures. Judicious choice of linker size, geometry, and connectivity can create diverse structures and topologies, which can aid in the quest to design MOFs with both high stability and permanent porosity. Multi-connected linkers have become a focus in the MOF community, as high connectivity can improve stability and tunability of frameworks. In particular, multicarboxylate ligands have been reported extensively in the literature to construct stable MOFs with versatile pore environments, which can be termed as metal-multicarboxylate frameworks (MMCFs). These structures have great application potential in gas adsorption and separation, catalysis, and sensing. In this work, we review the literature on multicarboxylate linkers (n COOH ≥ 3) in MOF systems and their applications, with specific emphasis on how high linker connectivity affects properties of MOFs such as topology, porosity, stability, and functionality.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Elucidating the speciation of extracted lanthanides by diglycolamides

Many studies over the past few decades have been devoted to addressing the application of diglycolamides (DGAs) for hydrometallurgical-based, f-element separations. Work to date has shown the molecular structure of a DGA derivative can have a significant impact on intra-lanthanide partitioning patterns. More recent studies have pushed towards probing the structure function relationship of the lanthanide-DGA complex to enable the design of more efficient lanthanide separation systems. Spectroscopic techniques, such as UV–Visible, Fourier Transformed Infrared Spectroscopy (FT-IR), Nuclear Magnetic Resonance (NMR), and Extended X-ray Absorption Fine Structure (EXAFS), provide information regarding the inner-sphere coordination of a given lanthanide-DGA complex. Scattering techniques, such as Dynamic Light Scattering (DLS), Small-Angle X-ray Scattering (SAXS), and Small-Angle Neutron Scattering (SANS), address nanoscale structures including aggregate sizes and morphology. Here, this review assesses the current state-of-knowledge regarding lanthanide-DGA hydrometallurgical (i.e., solvent extraction systems) interrogated using spectroscopic and scattering techniques to characterize the extracted Ln 3+ DGA species. Of particular interest to this review is the impact of varied diluents, inclusion and variation of phase modifiers, and DGA derivatization on system characteristics. While there has been extensive literature on the application of DGAs for f-element separations, the literature lacks a collective assessment of the speciation of Ln 3+ in the organic phase. This review provides new insights into the field of DGA separations, explicitly with an application to intra-lanthanide separations. Specifically, this review illustrates the importance of both the co-extraction anion (Cl - , NO 3 - , or ClO 4 - ) as it pertains to both the aggregate size and Ln 3+ distribution coefficient. It is evident the ability of the anion to disrupt the hydrogen bonding network limits both aggregate size and distribution coefficients according to the Hoffmeister series. This suggests the importance of the large, softer anions with a low charge-to-surface area ratio on encouraging hydrogen bond interactions. In addition, the co-extracted cation (H + vs Na + ) is important for mitigating transfer of Ln 3+ from the aqueous to the organic phase through extensive hydrogen bonding networks. These networks are responsible for forming supramolecular aggregates where a change in morphology is observed with increasing concentrations of H + and/or Ln 3+ in the organic phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

On the pressure and temperature dependence of adsorption densities and other thermodynamic properties in gas shales

Black shale source rocks have become a key natural gas resource in the US and China. Unlike in conventional hydrocarbon reservoirs, a significant fraction of the gas in shales is adsorbed onto the inordinate specific surface areas (SSA) of micropores inside organic matter with densities exceeding those of bulk gas by an order of magnitude. Yet, the distribution of adsorbed versus bulk gas remains poorly understood. Experiments measure excess adsorption isotherms, which are corrected to absolute adsorption amounts by a factor that involves the density, &#x3C1; abs , of the adsorption layer(s). Constant values of &#x3C1; abs are widely used in the literature but, we argue, are inconsistent with the pressure- and temperature-dependence of adsorption behavior. In this work, we propose a more reliable approach that assumes a constant volume of each adsorption layer that can be determined from the SSA of the substrate. We measure nine high-pressure methane excess adsorption isotherms up to 15 MPa for three shale samples from China and Germany at temperatures of 65, 75, and 95 °C, and low-pressure carbon dioxide and nitrogen isotherms to estimate the SSA. We also investigate another 24 isotherms at 35, 50, and 60° C or 8 Chinese shale samples and 3 isotherms at 60, 90, and 120° C for an Argentinian shale sample from the literature. A new variation of the multi-layer Ono-Kondo lattice model is introduced to derive the temperature and pressure dependent adsorption layer densities, which are subsequently used to obtain the absolute adsorption isotherms of interest. Finally, this practical methodology has the potential to significantly improve our estimates of shale gas-in-place resources, and adsorption modeling more broadly.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Accurate hydrodynamic force and torque correlations for prolate spheroids from Stokes regime to high Reynolds numbers

Detailed simulations of flow around various prolate spheroids are performed using multi-relaxation time lattice Boltzmann method (LBM). The simulations are performed in the Reynolds numbers range 0.1 ≤ Re ≤ 2000 at different incident angles 0°≤ φ ≤ 90° for various prolate spheroids of aspect ratios 1 ≤ λ ≤ 8. The Re is based on the volume equivalent sphere diameter. From the simulations, accurate correlations for average drag, lift and torque coefficients (C D , C L , and C T respectively) are proposed. The mean deviations between the correlations and the simulation data for C D , C L , and C T are 2%, 6.5%, and 4.7% respectively. Furthermore, the correlations are fitted with the physics in mind such that they can be extrapolated beyond the regimes simulated. The fits are designed such that correlations reduce to analytical (C D and C L ) solutions available for prolate spheroids in the limit Re ≈ 0. At high Re, the correlations mimic the asymptotic flattening of C D as for spheres and therefore, we expect the correlations to be valid until the critical Re (≈ 10 5 ). Furthermore, extensive comparison of our correlations with other high-fidelity simulations from literature demonstrate the accuracy of our work compared to other correlations from literature. This work enables researchers to perform accurate unresolved Euler-Lagrangian simulations for a wide range of elongated particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Ultrasonic degradation of GenX (HFPO-DA) – Performance comparison to PFOA and PFOS at high frequencies

Sonolytic degradation kinetics of hexafluoropropylene oxide-dimer acid (HFPO-DA or GenX) were studied for the first time at four high ultrasonic frequencies (375, 580, 860 and 1,140kHz) and three power densities (200, 300 and 400W/L), and compared to the degradation of previously studied perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS). The frequency of 580kHz displayed the highest degradation of all three PFAS tested. Within each frequency, the degradation performance increased consistently with increasing power density. Degradation rates were highest for GenX over PFOA to PFOS (k GenX = 0.0501 min -1 , k PFOA = 0.0444 min -1 , k PFOS 0.0153 min -1 ), which is in direct agreement with their reported thermal stability (PFOS > PFOA > GenX). No known by-product formation as expected from the literature on truncation mechanism was detected in the samples (i.e. shorter chain carboxylic acid PFAS). Further, fluorine mass balance experiments at 580kHz and 400W/ L confirmed that GenX defluorinated fastest among the three tested PFAS and had lowest loss of fluorine in the mass balance. Degradation experiments with a mixture of all three PFAS displayed lower degradation rates than the individual experiments, where PFOA exhibited the largest reduction in degradation rate (by 31%), followed by GenX (by 19%), and finally by PFOS (by 17%). Overall, our study demonstrates that ultrasound can provide effective destruction of different PFAS (70-90% fluorine from mitigated PFAS was detected as inorganic fluoride) with a similar energy demand to alternative PFAS treatment methods reported in literature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A dissolution model of alite coupling surface topography and ions transport under different hydrodynamics conditions at microscale

Portland cement is the most produced material in the world. The hydration process of cement consists of a group of complex chemical reactions. In order to investigate the mechanism of cement hydration, it is vital to study the hydration of each phase separately. An integrated model is proposed in this paper to simulate the dissolution of alite under different hydrodynamic conditions at microscale, coupling Kinetic Monte Carlo model (KMC), Lattice Boltzmann method (LBM) and diffusion boundary layer (DBL). The dissolution of alite is initialised with KMC. Two Multiple-relaxation-time (MRT) LB models are used to simulate the fluid flow and transport of ions, respectively. For solid-liquid interface, DBL is adapted to calculate the concentration gradient and dissolution flux. The model is validated with experiment from literature. The simulation results show good agreements with the results published in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Physical and chemical effects of isopropanol exchange in cement-based materials

Drying cement-based materials is a necessary step to characterize the microstructure by microscopy, adsorption, or mercury intrusion. The isopropanol (IPA) exchange method is commonly used to replace the pore solution prior to drying, as it reduces the capillary pressure and thereby helps to preserve the microstructure of the hydrated cementitious materials. However, some physical and chemical effects of IPA on hydration products have been reported. These effects cannot be completely avoided, but can be reduced by shortening the exchange duration, in particular for effects on ettringite. This study carried out experiments with different exchange durations and IPA removal techniques to address research gaps in the literature. For 1-mm cubes of cement paste with IPA diffusion coefficient of 1 × 10{sup −11} m{sup 2}/s, the compared exchange durations are 5 min, 15 min (value from the literature), 40 min (when the mixture at the sample center achieves 95% of the drop in surface tension from water to IPA), 80 min (when the IPA/water mixture at the sample center reaches an azeotrope), 5 h (when over 99% IPA is replaced at the sample center), and 24 h (prolonged exchange). After IPA exchange, samples were either directly dried at 40 °C with flushing N{sub 2} or washed by diethyl ether prior to N{sub 2} drying. Even though the exchange duration of 40 and 80 min, in theory, can reduce the damage from capillary pressure, the nitrogen adsorption results do not show any advantage in preventing microstructural alteration. The 5-h exchange provided results similar to the 24-h exchange, but the latter induced slightly more serious chemical effects resulting from the longer contact of IPA with hydration products. In addition, the compared IPA removal techniques do not show significant differences. Therefore, this study suggests using small samples (~1 mm) for microstructural studies following IPA exchange for a period corresponding to the time when 99% of the water (mole fraction) at the sample center is replaced.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Thermal energy storage in concrete: Review, testing, and simulation of thermal properties at relevant ranges of elevated temperature

This study examines the thermal performance of concrete used for thermal energy storage (TES) applications. The influence of concrete constituents (aggregates, cementitious materials, and fibers) on the thermal conductivity and specific heat are summarized based on literature and via experimentation at elevated temperatures. It is indicated that concrete with siliceous aggregate, low water/cement ratios, and steel fibers produces better overall thermal properties. The results of literature review and laboratory testing are used for numerical simulation to evaluate the impact of concrete thermal property variability on TES capabilities. The TES module consists of the heat exchanger and surrounding concrete as the storage media. Both idealized cases without heat loss and realistic cases with insulation and heat losses are considered. Furthermore, the result shows that conventional concrete mixes can be tailored to decrease the module charge/discharge durations and increase the amount of thermal energy storage.

25 ENERGY STORAGE↗
DOE OSTI2024

Hydrothermal solubility of Dy hydroxide as a function of pH and stability of Dy hydroxyl aqueous complexes from 25 to 250 °C

The rare earth elements (REE) have important applications in green energy technologies. The formation of mineral deposits in geologic systems commonly involves hydrothermal fluids which can mobilize the REE. However, the REE speciation is not well known as a function of pH. The thermodynamic properties of REE hydroxyl complexes used in geochemical models are based on the Helgeson-Kirkham-Flowers (HKF) equation of state parameters which were derived by extrapolation of low temperature experimental and estimated data. In this study, Dy hydroxide solubility experiments are combined with available literature data to improve these models from 25 to 250 °C and optimize the thermodynamic properties of Dy 3+ and Dy hydroxyl complexes using GEMSFITS. Batch-type solubility experiments were conducted from 150 to 250 °C and at saturated water vapor pressure in perchloric acid solutions with initial pH values of 2 to 5 in 0.5 pH unit increments. The measured solubility of Dy hydroxide is retrograde with temperature and decreases with pH. The logarithm of total dissolved Dy molality ranges from –2.3 to –5.3 at 150 °C (pH 4.7–5.5), from –2.4 to –5.6 at 200 °C (pH 3.9–5.1), and from –3.7 to –6.9 at 250 °C (pH of 3.4 and 5.0). The optimized standard partial molal Gibbs energies of formation (Δ f G° T ) derived for Dy 3+ and DyOH 2+ display a close to linear relationship with temperature, fitting with previous optimizations based on DyPO 4 solubility data in the literature. A comparison of the optimized ΔfG°T values for aqueous Dy species with predictions from available HKF parameters indicates significant differences ranging from +11 to –26 kJ/mol between 25 and 250 °C. The experimental fits are used to derive the Dy hydroxide solubility products (K s0 ) and formation constants for the hydrolysis of Dy (β n with n = 1 to 3; Dy 3+ + nOH – = DyOH n 3-n ) as a function of temperature. The optimization method presented yields accurate thermodynamic properties for the Dy 3+ aqua ions and the DyOH 2+ species at the acidic to mildly acidic pH studied whereas more experimental work is needed at near-neutral and alkaline conditions to better constrain the other hydroxyl complexes. Furthermore, the optimized thermodynamic data have a significant impact on geochemical modeling of the mobility and solubility of REE minerals in acidic hydrothermal fluids.

58 GEOSCIENCES↗
DOE OSTI2020

Fuel molecular structure effect on autoignition of highly branched iso-alkanes at low-to-intermediate temperatures: Iso-octane versus iso-dodecane

Highly branched iso-alkanes are an important class of hydrocarbons found in conventional petroleum-derived and alternative renewable fuels used for combustion applications. Recognizing that chemical kinetics for most of these iso-alkanes, especially at low-to-intermediate temperatures, has not been well studied, an experimental and modeling investigation of two selected iso-alkanes, iso-octane (2,2,4-trimethylpentane, iC8) and iso-dodecane (2,2,4,6,6-pentamethylheptane, iC12), is conducted to understand the fuel molecular structure effect on their autoignition characteristics. Using a rapid compression machine (RCM), the ignition responses of iC8 and iC12 at varying pressures, temperatures, and equivalence ratios are characterized and compared. The newly-acquired experimental ignition delay times have been compared with the literature RCM and shock tube data, demonstrating the complementary nature of the current dataset. Further comparison of the experimental pressure traces and ignition delay times illustrates the reactivity crossover between iC8 and iC12. Namely, there exists a temperature window in the negative temperature coefficient regime within which iC12 is less reactive than iC8, but iC12 becomes more reactive outside this temperature window. Furthermore, a chemical kinetic model of iso-alkanes including both iC8 and iC12 is developed. Simulated results using this model are then compared to the experimental data obtained in this study and available in the literature, showing its ability to predict the experimental trends. Chemical kinetic analyses have also been conducted to identify the important reaction pathways controlling autoignition at varying conditions, and to elucidate the underlying mechanism leading to different reactivity trends between iC8 and iC12.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

An experimental investigation of flame and autoignition behavior of propane

We report autoignition delay time data are one important means to develop, quantify, and validate fundamental understanding of combustion chemistry at low temperatures (T<1200 K). However, low-temperature chemistry often has higher uncertainties and scatter in the experimental data compared with high-temperature ignition data (T>1200 K). In this study, autoignition properties of propane and oxygen mixtures were investigated using the University of Michigan rapid compression facility in order to understand the effects of ignition regimes on low-temperature ignition data. For the first time for propane, autoignition delay times were determined from pressure histories, and autoignition characteristics were simultaneously recorded using highspeed imaging of the test section through a transparent end-wall. Propane mixtures with fuel-to-O 2 equivalence ratios of φ = 0.25 and φ = 0.5 and O 2 -to-inert gas molar ratios of 1:3.76 were studied over the pressure range of 8.9 to 11.3 atm and the temperature range of 930 – 1070 K. The results showed homogeneous or strong autoignition occurred for all φ = 0.25 experiments, and inhomogeneous or mixed autoignition occurred for all φ = 0.5 experiments. While a limited temperature range is covered in the study, importantly the data span predicted transitions in autoignition behavior, allowing validation of autoignition regime hypotheses. Specifically, the results agree well with strong-autoignition limits proposed based on the Sankaran Criterion. The autoignition delay time data at the strong-ignition conditions are in excellent agreement with predictions using a well-validated detailed reaction mechanism from the literature and a zerodimensional modeling assumption. However, the experimental data at the mixed autoignition conditions were systematically faster than the model predictions, particularly at lower temperatures (T< ~970 K). The results are an important addition to the growing body of data in the literature that show mixed autoignition phenomena are important sources of the higher scatter observed in the low-temperature autoignition data for propane and other fuels. The results are discussed in terms of different methods to capture the effects of pre-autoignition heat release associated with mixed autoignition conditions and thereby address some of the discrepancies between kinetic modeling and experimental measurements.

42 ENGINEERING↗
DOE OSTI2021

Autoignition study of iso -cetane/tetralin blends at low temperature

iso-Cetane and tetralin are the two fuel components commonly considered in literature diesel surrogates, and are hydrocarbon classes representative of iso-alkanes and naphthoaromatics, respectively. Since both surrogate components are involved in the key reactions controlling the autoignition reactivity of diesel surrogates, autoignition studies of iso-cetane, tetralin, and their blending behavior at low temperatures can be helpful in developing/refining chemical kinetic models of diesel surrogates, in order to better predict diesel ignition response under low temperature combustion conditions. In this investigation, autoignition experiments of iso-cetane, tetralin, and their binary mixtures at varying blending ratios have been conducted in a rapid compression machine (RCM) in the temperature/pressure range of 630–930 K and 10–20 bar. For the neat fuel components, the newly-acquired RCM data have been compared with the literature experimental results at some overlapping conditions. In addition, a chemical kinetic model describing the oxidation of iso-cetane and tetralin compiled/updated from the diesel surrogate model developed by Lawrence Livermore National Laboratory is used to simulate the experimental datasets. It is shown that this model exhibits good agreement with the experimental results of tetralin and also predicts the total ignition delay times of iso-cetane at lower temperatures reasonably well. However, the current model fails to fully capture the increase of total ignition delay time with increasing amount of tetralin in the binary blends observed in the present RCM experiments. Therefore, chemical kinetic analyses of the current model are conducted to help identify possible reasons leading to the discrepancies between simulations and experiments. Furthermore, the chemical kinetic interactions between iso-cetane and tetralin are explored by including additional cross-reactions among iso-cetane, tetralin, and their fuel fragments in the current model to assess their effects on model predictions. As a result, based on the chemical kinetic analysis results, future direction for model refinements is discussed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Shock tube investigation of high-temperature, extremely-rich oxidation of several co-optima biofuels for spark-ignition engines

To reduce the reliance on fossil fuels in the transportation sector and increase combustion efficiency, the Co-Optima initiative from US Department of Energy identified the top 10 biofuels for downsized, boosted, spark-ignition engines. Most of these biofuels have detailed reaction mechanisms available in literature developed based on studies at temperatures lower than 1700 K and an equivalence ratio of less than five. As such, the performance of these detailed mechanisms at high temperature and extremely rich conditions are unknown. It is important to validate kinetic mechanisms at these conditions because they are conducive to soot formation. Prediction of soot by chemical kinetic models relies on the prediction of underlying benchmark species like carbon monoxide and ethylene. In this work, we conduct high temperature (1700–2050 K) and high equivalence ratio(Φ=8.6) oxidation of these biofuels, namely 2,4,4-trimethyl-1-pentene (α-diisobutylene), ethanol, cyclopentanone, methyl acetate, and 2-methylfuran, blended in ethylene behind reflected shock waves at 4–4.7 atm pressure. Carbon monoxide and ethylene time histories are measured simultaneously using a continuous feedback quantum cascade laser near 4.9 µm and a tunable CO 2 gas laser at 10.532 nm, respectively. Results show that ethanol blend forms more carbon monoxide than other biofuels and consumes ethylene faster than the biofuel blends in the temperature range considered. Overall, the performance of different mechanisms in literature are evaluated against the experimental results. The novel reaction mechanism ‘the Co-Optima model’, which includes the sub mechanisms for all the biofuels in this study, was found to be the best mechanism for the experimental conditions studied.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Automatically generated model for light alkene combustion

Light alkenes are common combustion intermediates for a variety of fuels. Therefore, understanding their oxidation and pyrolysis chemistry is key to building detailed mechanisms for heavier fuels. This work was focused on the development and evaluation of a detailed kinetic mechanism suitable for the combustion of light alkenes up to C 4 without the use of tuned parameters, instead, the parameter values come from first principles or direct measurements. The generated mechanism accurately estimates the laminar burning velocity (S u ) and ignition delay time (IDT) of light alkenes available in the literature, which represent fundamental combustion properties at a wide range of conditions. Because each parameter is thought to have a physically realistic value, not tuned to these measurements, the new model could be used as a sub-mechanism in models for other applications. The reaction network was generated with the open-source Reaction Mechanism Generator (RMG) software. Sensitivity analyses were performed under wide ranges of temperatures and pressures, allowing for the identification of the most impactful species and reactions. Based on these, a comprehensive thermochemistry database, including calculations on 550 molecules performed in this work at the CBS-QB3 level of theory, and a kinetic library, including theoretically-derived reaction rates retrieved from the literature, were built and used in the mechanism generation. The developed mechanism was compared against several existing detailed kinetic mechanisms for ethene, propene, 1-butene, 2-butene, and isobutene. Here, the newly generated model is the most accurate among the ones analyzed, in terms of fractional bias and normalized mean square error. Hence, this new model was used to analyze the chemistry of alkene combustion. Key rate coefficients were compared, to identify the cause of deviations between the models and possible areas for further improvements.

09 BIOMASS FUELS↗