Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “foams”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Bonding of reusable surface insulation with low density silicone foams

The development and evaluation of a reduced density, high reliable foamed bond strain isolation system for attaching reusable surface insulation to the space shuttle structure are reported. Included are data on virgin materials as well as on materials that received 100 cycles of exposure to 650 F for approximately 20 minutes per cycle. Room temperature vulcanizing silicon elastomers meet all the requirments for an adhesive bonding system.

Hiltz, A. A.↗
NASA NTRS1975

Fiber-modified polyurethane foam for ballistic protection

Closed-cell, semirigid, fiber-loaded, self-extinguishing polyurethane foam material fills voids around fuel cells in aircraft. Material prevents leakage of fuel and spreading of fire in case of ballistic incendiary impact. It also protects fuel cell in case of exterior fire.

Fish, R. H.↗
NASA NTRS1975

Foam-machining tool with eddy-current transducer

Three-cutter machining system for foam-covered tanks incorporates eddy-current sensor. Sensor feeds signal to numerical controller which programs rotational and vertical axes of sensor travel, enabling cutterhead to profile around tank protrusions.

Copper, W. P.↗
NASA NTRS1975

PPO foam - Liquid hydrogen insulation

An extensive fabrication and test program is described which has demonstrated the integrity of PPO (polyphenylene oxide) foam as an internal insulation. PPO is shown to be capable of withstanding multiple reuses on such cryogenic-fueled launch vehicles as the Space Shuttle. The major advantages of this internal insulation is the absence of a pressure load on the insulation, reduced handling damage, and minimization of cyclic thermal stresses by a 'warm' bond line.

Yates, G. B.↗
NASA NTRS1976

3-D foam adhesive deposition

Bonding method, which reduces amount and weight of adhesive, is applicable to foam-filled honeycomb constructions. Novel features of process include temperature-viscosity control and removal of excess adhesive by transfer to cellophane film.

Lemons, C. R.↗
NASA NTRS1976

Mixing insert for foam dispensing apparatus

A device for mixing foam ingredients is described. The device comprises an arrangement of lands situated about a cylindrical elongated shaft-like member with each land having a slot. The slots of alternate lands are positioned 180 deg from each other so that as the ingredients flow through the mixing chamber they flow from adjacent one side of the housing to the other dividing as such passes around the shaft-like member.

Simpson, W. G.↗
NASA NTRS1976

Open cell fire-resistant foam

Candidate polyphosphazene polymers were investigated to develop a fire-resistant, thermally stable and flexible open cell foam. The copolymers were prepared in several mole ratios of the substituent side chains and a (nominal) 40:60 derivative was selected for formulation studies. Synthesis of the polymers involved solution by polymerization of hexachlorophosphazene to soluble high molecular weight poly(dichlorophosphazene), followed by derivatization of the resultant polymer in a normal fashion to give polymers in high yield and high molecular weight. Small amounts of a cure site were incorporated into the polymer for vulcanization purposes. The poly(aryloxyphosphazenes) exhibited good thermal stability and the first polymer mentioned above exhibited the best thermal behavior of all the candidate polymers studied.

Thompson, J. E.↗
NASA NTRS1977

Closed-cell foams produced from sputter-deposited aluminum

Sputter deposited aluminum containing argon was melted to produce foam, both in the earth's gravitational field and in a zero-gravity space environment. Experiments leading to trapping of up to 270 ppm argon sputtering gas in pure aluminum during high-rate dc triode sputter deposition are discussed. Conduct of the melting experiments and design of the furnace used are described. Metallography; an analysis of bubble size, distribution, and morphology; and a preliminary description of the kinetics are also presented.

Patten, J. W.↗
NASA NTRS1977

Toxicity studies of a polyurethane rigid foam

Relative toxicity tests were performed on a polyurethane foam containing a trimethylopropane-based polyol and an organophosphate flame retardant. The routine screening procedure involved the exposure of four Swiss albino male mice in a 4.2 liter hemispherical chamber to the products generated by pyrolyzing a 1.00 g sample at a heating rate of 40 deg C/min from 200 to 800 C in the absence of air flow. In addition to the routine screening, experiments were performed with a very rapid rise to 800 C, with nominal 16 and 48 ml/sec air flow and with varying sample rates. No unusual toxicity was observed with either gradual or rapid pyrolysis to 800 C. Convulsions and seizures similar to those previously reported were observed when the materials were essentially flash pyrolyzed at 800 C in the presence of air flow, and the toxicity appeared unusual because of low sample weights required to produce death.

Hilado, C. J.↗
NASA NTRS1978

High-rise foam-in-place process

Large polyurethane parts are molded by sequential pouring without waiting for foam to cure. Joints between pours and tops of parts are free of voids and need no trimming.

Liskay, G. G.↗
NASA NTRS1977

Evaluation of a low-density polyimide foam in a dynamic, high temperature environment

A low density polyimide foam material was tested in an arc tunnel to determine its potential for heat shield application on aerospace vehicles. The results show that the material has some reuse potential at surface temperatures as high as 750 K. When a black refractory paint was applied to the surface of the material, the surface recession was negligible at 750 K. An analytical thermal conductivity was derived for this material which, combined with measured thermal property values, can be used to make preliminary design thickness calculations for heat shield applications.

Pittman, C. M.↗
NASA NTRS1977

Polychloroprene flexible foam as a reference material

Polychloroprene flexible foam was evaluated as a reference material for fire toxicity tests. A commercial sample was evaluated using nine different test conditions of the USF methodology. The material exhibited a wide range of relative toxicity depending on the test conditions. Times to incapacitation and times to death were shortest at 16 ml/sec (1 l/min) air flow, at any fixed heating rate and upper limit temperature.

Hilado, C. J.↗
NASA NTRS1978

Flash-fire propensity of rigid foam insulation

Twelve samples of rigid foam insulation were evaluated for flash-fire propensity, using the USF flash-fire screening test method. These materials exhibited little or no flash-fire propensity under these particular test conditions.

Hilado, C. J.↗
NASA NTRS1980

"Grinding" cavities in polyurethane foam

Grinding tool installed on conventional milling machine cuts precise cavities in foam blocks. Method is well suited for prototype or midsize production runs and can be adapted to computer control for mass production. Method saves time and materials compared to bonding or hot wire techniques.

Brower, J. R.↗
NASA NTRS1980

Foam-filled cushions for sliding trays

Polytetrafluoroethylene tube filled with polyurethane foam forms low friction sliding surface that cushions vibrations and absorbs manufacturing tolerances and misalignment. Possible uses include packaging of components for shipping and seals for doors in lockers, cars, and refrigerators.

Nahin, S. B.↗
NASA NTRS1979

Effects of soft foam insulation impact

High temperature reusable surface insulation (HTRSI) tiles were impacted by a variety of foam insulation materials typical of the debris expected to strike the shuttle orbiter during the initial phases of flight. Failure of the HIRSI coating was strongly dependent on the density and size of the projectile. The failure threshold was as low as 140 ft/sec for rubber and as high as 740 ft/sec for styrofoam. In addition, the impact pressure was measured for a variety of debris materials as a function of velocity.

Rand, J. L.↗
NASA NTRS1979

Catalysts for polyimide foams from aromatic isocyanates and aromatic dianhydrides

Polyimide foam products having greatly improved burn-through and flame-spread resistance are prepared by the reaction of aromatic polyisocyanates with aromatic dianhydrides in the presence of metallic salts of octoic acid. The salts, for example stannous octoate, ferric octoate and aluminum octoate, favor the formation of imide linkages at the expense of other possible reactions.

Riccitiello, S. R.↗