SEARCH · Engineering Papers

Results for “fibers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

All sources NASA NTRS DOE OSTI

NASA NTRS2002

Tensile Behavior of As-Fabricated and Burner-Rig Exposed SiC/SiC Composites with Hi-Nicalon Type-S Fibers

Tensile stress-strain curves were measured at room temperature and 1315 C for 2D-woven SiC/BN/SiC ceramic matrix composites (CMC) reinforced by two variations of Hi-Nicalon Type-S SiC fibers. These fibers, which contained a thin continuous carbon-rich layer on their as-produced surface, provided the as-fabricated CMC with good composite behavior and an ultimate strength and strain of -350 MPa and -0.5%, respectively. However, after un-stressed burner-rig exposure at 815 C for -100 hrs, CMC tensile specimens with cut edges and exposed interphases showed a significant decrease in ultimate properties with effectively no composite behavior. Microstructural observations show that the degradation was caused by internal fiber-fiber oxide bonding after removal of the carbon-rich fiber surface layer by the high-velocity combustion gases. On the other hand, SiC/BN/SiC CMC with Sylramic-iBN fibers without carbon-rich surfaces showed higher as-fabricated strength and no loss in strength after the same burner rig exposure. Based on the strong role of the carbon layer in these observations, a process method was developed and demonstrated for achieving better strength retention of Hi-Nicalon Type-S CMC during burner rig exposure. Other general approaches for minimizing this current deficiency with as-produced Type-S fibers are discussed.

Yun, H. M.↗

NASA NTRS2013

Cobra Fiber-Optic Positioner Upgrade

A prime focus spectrometer (PFS), along with corrective optics, will mount in place of the secondary mirror of the Subaru telescope on Mauna Kea, Hawaii. This will allow simultaneous observations of cosmologic targets. It will enable large-scale galactic archeology and dark energy surveys to help unlock the secrets of the universe. To perform these cosmologic surveys, an array of 2,400 optical fibers needs to be independently positioned within the 498-mm-diameter focal plane of the PFS instrument to collect light from galaxies and stars for spectrographic analyses. To allow for independent re-positioning of the fibers, a very small positioner (7.7 mm in diameter) is required. One hundred percent coverage of the focal plane is also required, so these small actuators need to cover a patrol region of 9.5 mm in diameter. To optimize the amount of light that can be collected, the fibers need to be placed within 5 micrometers of their intended target (either a star or galaxy). The Cobra Fiber Positioner was designed to meet the size and accuracy requirements stated above. Cobra is a two-degrees-of-freedom mechanism that can position an optical fiber in the focal plane of the PFS instrument to a precision of 5 micrometers. It is a theta-phi style positioner containing two rotary piezo tube motors with one offset from the other, which enables the optic fibers to be placed anywhere in a small circular patrol region. The patrol region of the actuator is such that the array of 2,400 positioners allows for full coverage of the instrument focal plane by overlapping the patrol areas. A second-generation Cobra positioner was designed based on lessons learned from the original prototype built in 2009. Improvements were made to the precision of the ceramic motor parts, and hard stops were redesigned to minimize friction and prevent jamming. These changes resulted in reducing the number of move iterations required to position the optical fiber within 5 micrometers of its target. At the time of this reporting, there are still many tests to be performed that will validate system level performance, but on an individual level, the Cobra positioner demonstrates excellent performance and will enable the PFS instrument to make unprecedented measurements of the universe. What is unique about the upgrades made to the Cobra positioner is the improved performance due to the design changes in the hard stops and the ceramic end caps of the motors. Other changes were made to reduce the unit cost of a Cobra positioner without affecting the performance, since thousands of these devices will have to be built for the PFS instrument.

Fisher, Charles D.↗

NASA NTRS2014

An Intrinsic Fiber-Optic Sensor for Structure Lightning Current Measurement

An intrinsic optical-fiber sensor based on Faraday Effect is developed that is highly suitable for measuring lightning current on aircraft, towers and complex structures. Originally developed specifically for aircraft installations, it is light-weight, non-conducting, structure conforming, and is immune to electromagnetic interference, hysteresis and saturation. It can measure total current down to DC. When used on lightning towers, the sensor can help validate other sensors and lightning detection network measurements. Faraday Effect causes light polarization to rotate when the fiber is exposed to a magnetic field in the direction of light propagation. Thus, the magnetic field strength can be determined from the light polarization change. By forming closed fiber loops and applying Ampere's law, measuring the total light rotation yields the total current enclosed. A broadband, dual-detector, reflective polarimetric scheme allows measurement of both DC component and AC waveforms with a 60 dB dynamic range. Two systems were built that are similar in design but with slightly different sensitivities. The 1310nm laser system can measure 300 A - 300 kA, and has a 15m long sensing fiber. It was used in laboratory testing, including measuring current on an aluminum structure simulating an aircraft fuselage or a lightning tower. High current capabilities were demonstrated up to 200 kA at a lightning test facility. The 1550nm laser system can measure 400 A - 400 kA and has a 25m fiber length. Used in field measurements, excellent results were achieved in the summer of 2012 measuring rocket-triggered lightning at the International Center for Lightning Research and Testing (ICLRT), Camp Blanding, Florida. In both systems increased sensitivity can be achieved with multiple fiber loops. The fiber optic sensor provides many unique capabilities not currently possible with traditional sensors. It represents an important new tool for lightning current measurement where low weight, complex shapes, large structure dimension, large current, and low frequency capabilities are important considerations.

Nguyen, Truong X.↗

NASA NTRS2014

A Multiscale Progressive Failure Modeling Methodology for Composites that Includes Fiber Strength Stochastics

A multiscale modeling methodology was developed for continuous fiber composites that incorporates a statistical distribution of fiber strengths into coupled multiscale micromechanics/finite element (FE) analyses. A modified two-parameter Weibull cumulative distribution function, which accounts for the effect of fiber length on the probability of failure, was used to characterize the statistical distribution of fiber strengths. A parametric study using the NASA Micromechanics Analysis Code with the Generalized Method of Cells (MAC/GMC) was performed to assess the effect of variable fiber strengths on local composite failure within a repeating unit cell (RUC) and subsequent global failure. The NASA code FEAMAC and the ABAQUS finite element solver were used to analyze the progressive failure of a unidirectional SCS-6/TIMETAL 21S metal matrix composite tensile dogbone specimen at 650 degC. Multiscale progressive failure analyses were performed to quantify the effect of spatially varying fiber strengths on the RUC-averaged and global stress-strain responses and failure. The ultimate composite strengths and distribution of failure locations (predominately within the gage section) reasonably matched the experimentally observed failure behavior. The predicted composite failure behavior suggests that use of macroscale models that exploit global geometric symmetries are inappropriate for cases where the actual distribution of local fiber strengths displays no such symmetries. This issue has not received much attention in the literature. Moreover, the model discretization at a specific length scale can have a profound effect on the computational costs associated with multiscale simulations.models that yield accurate yet tractable results.

Generalized Method of Cells↗

NASA NTRS2014

Methods for Producing High-Performance Silicon Carbide Fibers, Architectural Preforms, and High-Temperature Composite Structures

Methods are disclosed for producing architectural preforms and high-temperature composite structures containing high-strength ceramic fibers with reduced preforming stresses within each fiber, with an in-situ grown coating on each fiber surface, with reduced boron within the bulk of each fiber, and with improved tensile creep and rupture resistance properties tier each fiber. The methods include the steps of preparing an original sample of a preform formed from a pre-selected high-strength silicon carbide ceramic fiber type, placing the original sample in a processing furnace under a pre-selected preforming stress state and thermally treating the sample in the processing furnace at a pre-selected processing temperature and hold time in a processing gas having a pre-selected composition, pressure, and flow rate. For the high-temperature composite structures, the method includes additional steps of depositing a thin interphase coating on the surface of each fiber and forming a ceramic or carbon-based matrix within the sample.

DiCarlo, James A.↗

NASA NTRS2016

Magneto-Optic Field Coupling in Optical Fiber Bragg Gratings

The invention is a magneto-optic coupled magnetic sensor that comprises a standard optical fiber Bragg grating system. The system includes an optical fiber with at least one Bragg grating therein. The optical fiber has at least an inner core and a cladding that surrounds the inner core. The optical fiber is part of an optical system that includes an interrogation device that provides a light wave through the optical fiber and a system to determine the change in the index of refraction of the optical fiber. The cladding of the optical fiber comprises at least a portion of which is made up of ferromagnetic particles so that the ferromagnetic particles are subject to the light wave provided by the interrogation system. When a magnetic field is present, the ferromagnetic particles change the optical properties of the sensor directly.

Carman, Gregory P.↗

NASA NTRS2018

Implementation of Fiber Optic Sensing System on Sandwich Composite Cylinder Buckling Test

The National Aeronautics and Space Administration (NASA) Engineering and Safety Center Shell Buckling Knockdown Factor Project is a multicenter project tasked with developing new analysis-based shell buckling design guidelines and design factors (i.e., knockdown factors) through high-fidelity buckling simulations and advanced test technologies. To validate these new buckling knockdown factors for future launch vehicles, the Shell Buckling Knockdown Factor Project is carrying out structural testing on a series of large-scale metallic and composite cylindrical shells at the NASA Marshall Space Flight Center (Marshall Space Flight Center, Alabama). A fiber optic sensor system was used to measure strain on a large-scale sandwich composite cylinder that was tested under multiple axial compressive loads up to more than 850,000 lb, and equivalent bending loads over 22 million in-lb. During the structural testing of the composite cylinder, strain data were collected from optical cables containing distributed fiber Bragg gratings using a custom fiber optic sensor system interrogator developed at the NASA Armstrong Flight Research Center. A total of 16 fiber-optic strands, each containing nearly 1,000 fiber Bragg gratings, measuring strain, were installed on the inner and outer cylinder surfaces to monitor the test article global structural response through high-density real-time and post test strain measurements. The distributed sensing system provided evidence of local epoxy failure at the attachment-ring-to-barrel interface that would not have been detected with conventional instrumentation. Results from the fiber optic sensor system were used to further refine and validate structural models for buckling of the large-scale composite structures. This paper discusses the techniques employed for real-time structural monitoring of the composite cylinder for structural load introduction and distributed bending-strain measurements over a large section of the cylinder by utilizing unique sensing capabilities of fiber optic sensors.

FOS↗

NASA NTRSDate not supplied

New Developments in the CompDam Fiber Kinking Model for the Interaction of Kinking and Splitting Cracks with Application to Open Hole Compression Specimens

This paper describes two new additions to the NASA fiber kinking model: 1) A failure index for fiber kinking is developed to facilitate interaction between kinking and matrix cracking and 2) A criterion for fiber rupture is introduced to account for fiber breakage before or after fiber kinking. The model formulation is described with the aid of graphical Considered constructions to elucidate the behavior. Verification studies are conducted with single element models to show the behavior of the model in light of the new developments and to evaluate the effect of numerical parameters of the model. The model is used to analyze open hole compression specimens with soft, quasi-isotropic, and hard layups. Analysis results are shown for a conventional continuum damage mechanics model as well as the proposed model to highlight the differences between the two. Comparison with test data highlights the capabilities and remaining gaps in the quantitative prediction of damage evolution in open hole compression. Overall, the results show that the proposed model is capable of representing the kinematics of fiber kinking, and specifically the role of fiber kinking in open hole compression.

Andrew Cole Bergan↗

DOE OSTI2020

Method of making a distributed optical fiber sensor having enhanced Rayleigh scattering and enhanced temperature stability, and monitoring systems employing same

A method of making an optical fiber sensor device for distributed sensing includes generating a laser beam comprising a plurality of ultrafast pulses, and focusing the laser beam into a core of an optical fiber to form a nanograting structure within the core, wherein the nanograting structure includes a plurality of spaced nanograting elements each extending substantially parallel to a longitudinal axis of optical fiber. Also, an optical fiber sensor device for distributed sensing includes an optical fiber having a longitudinal axis, a core, and a nanograting structure within the core, wherein the nanograting structure includes a plurality of spaced nanograting elements each extending substantially parallel to the longitudinal axis of the optical fiber. Also, a distributed sensing method and system and an energy production system that employs such an optical fiber sensor device.

42 ENGINEERING↗

DOE OSTI2022

Method for controlling fiber growth in a laser heated pedestal growth system by controlling a laser power output, a pedestal feedstock rate of motion, and a draw rate

One or more embodiments relate to a method for controlling fiber growth and fiber diameter in a laser heated pedestal growth (LHPG) system so as to provide long, continuous single-crystal optical fibers of uniform diameter. The method generally provides three independent parameter feedback controls to control the molten zone height, laser power, and fiber drawing rates simultaneously in order to reduce the mismatch between instantaneous diameter changes and current diameter. The method permits the growth of fibers with non-uniform diameters along the fiber's length. The method also provides the capability to stop the LHPG system, remove the exhausted pedestal feedstock with a second pedestal feedstock, and restart the LHPG system to provide a continuous fiber.

Buric, Michael P.↗

DOE OSTI2022

Method of making a distributed optical fiber sensor having enhanced Rayleigh scattering and enhanced temperature stability, and monitoring systems employing same

Chen, Peng Kevin↗

DOE OSTI2023

Methods of making and using bulk products including fiber-containing particles with dual-tapered shape

Recycled carbon fibers are processed by rotational tumbling in a mixture with binder material to prepare fiber-containing particles having a dual-tapered shape and general alignment of fibers with a longitudinal direction of the particles. Bulk products including such fiber-containing particles are compounded with polymer and pelletized to prepare fiber-reinforced composite pellets, which are useful for applications such as injection molding to prepare molded products of carbon fiber-reinforced composite material with recycled carbon fibers.

Harris, Jordan Gray↗

DOE OSTI2023

Carbon fiber-nanoparticle composites with electromechanical properties

A carbon fiber composite material comprising: (i) a carbon fiber having an outer surface, a thickness of at least 1 micron, and an aspect ratio of at least 1000; (ii) a sizing agent coated on the outer surface of the carbon fiber, wherein the sizing agent has a thickness of up to 200 nm; and (iii) nanoparticles having a size in at least one dimension of up to 100 nm embedded within the sizing agent, wherein the nanoparticles have a metal carbide, metal oxide, metal nitride, and/or metal boride composition. A method for producing the fiber composite material comprises: (a) continuously feeding and coating a continuous carbon fiber with a liquid containing a solvent, sizing agent, and nanoparticles in a continuous feed-through process to result in said sizing agent and nanoparticles coating the surface of the continuous carbon fiber; and (b) removing the solvent from the coated fiber.

Bowland, Christopher C.↗

DOE OSTI2024

Fiber-containing particles with dual-tapered shape

Harris, Jordan Gray↗

DOE OSTI2024

Magnetic Field Sensing via Multi-Material Acoustic Sensing Optical Fibers with Magnetostrictive Cladding Inclusions

In this conducted research, optical fiber sensors are used to measure low strength alternating magnetic fields. Various fiber sensor configurations are tested and investigated to demonstrate sensing capabilities at different field magnitudes and frequencies. Distributed acoustic sensing fibers (DAS) have been largely studied and documented across a variety of applications and sensing systems. This research uses the DAS technology in tandem with magnetostrictive materials to create a distributed multi-material optical fiber magnetic sensor. Magnetic sensing has high demand across different fields and often runs into challenges of extreme environments including high temperature, corrosion, and areas with poor accessibility. The robust and distributed nature of optical fiber sensors which can be cheaply produced for long lengths is an attractive option over other single point magnetic sensors. In down hole applications specifically, having a distributed sensor able to be deployed easily and over long distances for magnetic sensing would be a large improvement to bulkier traditional magnetometers. In the conducted study, different magnetostrictive materials are implemented in distributed optical fiber sensors to analyze and compare the effective sensitivity and potential commercial viability. Nickel, galfenol alloy, and MetGlas alloy inclusions are drawn into fused silica optical fibers with Bragg gratings inscribed later on for DAS capability. Each was investigated for its response to varying AC magnetic fields to determine relative sensitivity and resolution for distributed magnetic field sensing.

Dejneka, Zach↗

DOE OSTI2020

Discontinuous micro-fibers as intrinsic reinforcement for ductile Engineered Cementitious Composites (ECC)

Engineered Cementitious Composites (ECC) have demonstrated superior mechanical and durability performance than conventional concrete. In the micromechanical reinforcing system of ECC, fibers play a pivotal role in establishing the ultrahigh tensile ductility and autogenous crack width control. This article reviews the state-of-the-art of discontinuous micro-fibers as intrinsic reinforcement of ECC regarding technical performance as well as environmental and economic impacts. Mechanical properties of ECC made with different micro-fibers, man-made or natural, and their embodied energy, emissions and material cost, are comprehensively surveyed. Further, studies on fiber hybridization are discussed regarding the combination of different types of fibers to form synergetic reinforcements that mitigate total material cost, and potentially enhance the composite performance. Lastly, recommendations on fiber selections are highlighted and directions for future research are suggested.

42 ENGINEERING↗

DOE OSTI2024

Dopant, coating, and grating effects in silica optical fibers under extreme neutron irradiation

Radiation effects on fiber Bragg gratings (FBGs) have been studied but data gaps related to the effects of displacement damage resulting from high fast neutron fluence remain. In this work, Type-I and Type-II FBGs inscribed in optical fibers with various core dopants (Ge and F) and fiber coatings (acrylate, polyimide) were monitored in situ during 75 days of neutron irradiation to a peak fast (>0.1 MeV) neutron fluence of 3 X 10 21 n fast /cm 2 . Further, the reflected intensity of the Type-I FBGs inscribed in a Ge-doped core fiber decreased by > 30 dB within 7 h of irradiation (10 19 n fast /cm 2 ), whereas Type-II FBGs inscribed in a pure silica core fiber eventually approached >40 dB attenuation after accumulating a fast neutron fluence on the order of 10 20 n fast /cm 2 . Type-II FBGs inscribed in F-doped core fiber improved stability: the attenuation approached an equilibrium value in the range of 10 to 20 dB.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Effect of the Segmental Structure of Thermoplastic Polyurethane (Hardness) on the Interfacial Adhesion of Textile-Grade Carbon Fiber Composites

In polymer composites, the fiber–matrix interface is primarily influenced by the surface treatment of the fibers and polymer morphology. Previous studies have investigated the effect of surface treatment of carbon fiber on the mechanical properties of the resulting composites. However, very few studies have explored the chemical structural modification of polymer effect on the fiber–matrix adhesion. In this work, the interfaces of soft thermoplastic polyurethane (S-TPU) and hard-segmented TPU (H-TPU) were investigated through surface, thermal, and mechanical characterization. A textile-grade carbon fiber (TCF) with 1% concentration of epoxy sizing (an emerging material for nonaerospace applications with 450 K filament tows) was used as a reinforcement to investigate the structure–property relationship at the interface. Atomic force microscopy results showed 39% higher surface roughness for S-TPU than for H-TPU. X-ray photoelectron spectroscopy results revealed a 550% increase in C=O content, which can provide multiple hydrogen bonding networks in H-TPU, and these C=O bonds can produce a strong chemical bond at the fiber–matrix interface. Additionally, dynamic mechanical analysis and differential scanning calorimetry results confirmed the presence of hydrogen bonding that enhances the cross-linked density by 232% in H-TPU compared to S-TPU. The improved mechanical properties of H-TPU composites, such as flexural, impact and tensile by 30, 50, and 130% compared to S-TPU composites, prove that the crystallinity and hydrogen bonding significantly increase the load bearing capacity due to the strong interface. The mechanical properties of TCF–TPU composites validate the formation of chemical bonds through a nucleophilic addition reaction at the interface and improve the bond strength of the composites. Thus, tailoring the polyurethane structure broadens the performance of segmented TPU in conjunction with TCF reinforcement, which has implications for cost-effective, high-strength composites.

36 MATERIALS SCIENCE↗