Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fiber composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Processable high temperature resistant addition type polyimide laminating resins

Basic studies that were performed using model compounds to elucidate the polymerization mechanism of the so-called addition-type (A-type) polyimides are reviewed. The fabrication and properties of polyimide/graphite fiber composites using A-type polyimide prepolymers as the matrix are also reviewed. An alternate method for preparing processable A-type polyimides by means of in situ polymerization of monomer reactants (PMR) on the fiber reinforcement is described. The elevated temperature properties of A-type PMR/graphite fiber composites are also presented.

Serafini, T. T.↗
NASA NTRS1995

Mechanical Properties of Continuous Fiber Reinforced Zirconium Diboride Matrix Composites

Continuous fiber reinforced zirconium diboride matrix composites, SCS-9a-(RBSiCZrB2)matrix, are being developed for leading edge, rocket nozzle and turbine engine applications. Recently, the composite materials have been characterized for tensile properties to 1250 C, the highest temperature tested. The tensile properties are fiber dominated as the matrix is microcracked on fabrication, but favorable failure characteristic are observed. Compression and shear mechanical testing results will be reported if completed. The effects of fiber volume fraction and matrix density on mechanical properties will be discussed. The target applications of the materials will be discussed. Specific testing being performed towards qualification for these applications will be included.

Stuffle, Kevin↗
NASA NTRS1982

Tensile properties of SiC/aluminum filamentary composites - Thermal degradation effects

Aluminium metal matrix composites with a low cost fiber, e.g. SiC, provide for an attractive combination of high elastic modulus and longitudinal strengths coupled with a low density. SiC (volume fraction 0.55)-aluminum (6061) systems have been studied in order to optimize fiber composite strength and processing parameters. A comparison of two SiC/aluminum composites produced by AVCO and DWA is provided. Fiber properties are shown to alter composite tensile properties and fracture morphology. The room temperature tensile strengths appear to be insensitive to thermal exposures at 500 C up to 150 h. The elastic modulus of the composites also appears to be stable up to 400 C, however variations in the loss modulus are apparent. The fracture morphology reflects the quality of the interfacial bond, fiber strengths and fiber processing.

Skinner, A.↗
DOE OSTI2020

Carbon Fiber Prepreg Recycling- Automated Perform Manufacturing Equipment (Final Technical Report)

Discontinuous fiber composites have a compelling business case as related to light metals such as aluminum and magnesium machined or die cast components. DFC’s have been in commercial production using carbon fiber/epoxy prepreg for both commercial aircraft and for military applications for a number of years and their usage is expanding into automotive and consumer goods components. Reasons for this include significantly lower cost as compared to continuous fiber composites easier design and understanding of the material by metal traditionalists, higher degree of part complexity with relatively simple and low cost molds when compared to high-pressure die casting, and potential for near zero waste. IACMI’s 10-year goals of reduction in carbon fiber reinforced plastics manufacturing cost by 25%, reduction in their embodied energy by 50%, and recyclability of 95% can all be advanced through robust recycling. With recycling We have shown that a 15% contribution in manufacturing cost reduction is feasible, that a significant reduction in embodied energy (over 90% for the recycled fraction) is achievable, and that when combined with primary pyrolysis recycling, the 95% target can be met. Large-scale application of advanced composites began with the aerospace industry, and CRTC’s location in Washington State provided access to a waste stream of nearly 900 tonnes/year that was going to landfill. As the aerospace industry has automated parts production, their material forms have become significantly easier to recycle, and some evidence of this exists for the future automotive and wind turbine components as well. CRTC decided to focus on re-purposing the carbon fiber/epoxy aerospace scrap streams through materials reformatting and reuse, and not on primary recycling (pyrolysis mainly) as this technology is commercially available. The main reasons for this were that it offers a route to effective use of the most widely available and consistent feedstock called edge-trim, as well as allows creation of complex and low-cost parts using rapid and cost-effective compression molding technologies. The reasons also include leading the way for potential automotive pre-preg recycling as the combination of roughly 85% virgin pre-preg and 15% recycled pre-preg directly supports IACMI’s goals and enables significant part cost reduction and a path to zero-waste composite manufacturing at the OEMs or Tier 1’s. The purpose of the project was to develop equipment and technology to transform continuous fiber pre-preg in roll forms into smaller chip-format DFC feedstock, and to determine impacts on moldability and performance based on lessons learned along the path. The availability of scrap from pre-preg manufacturers was a significant value to the program even though the aerospace pre-preg is designed to be autoclave molded thus has handling, tackiness, and processing factors that are not ideal for DFCs. The scope of the project was to develop a Phase 1 system that could identify and resolve some of the major hurdles, determine where to focus effort on building a commercial-scale Phase 2 system, and develop technology for handling a wide variety of incoming scrap materials to produce the most usable product. A chopping system was developed and reduced to practice via an experimental approach that enabled all forms of scrap coming from the pre-preg manufacturers and some forms of the scrap coming from OEM production lines to be very effectively re-purposed. The systems that were developed were not considered to be production robust but rather identified and resolved some of the major technical hurdles, and demonstrated the path towards effective full-scale commercialization.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Creep behavior of tungsten fiber reinforced niobium metal matrix composites

Tungsten fiber reinforced niobium metal matrix composites were evaluated for use in space nuclear power conversion systems. The composite panels were fabricated using the arc-spray monotape technique at the NASA Lewis Research Center. The creep behavior of W/Nb composite material was determined at 1400 and 1500 K in vacuum over a wide range of applied loads. The time to reach 1 percent strain, the time to rupture, and the minimum creep rate were measured. The W/Nb composites exceeded the properties of monolithic niobium alloys significantly even when compared on a strength to density basis. The effect of fiber orientation on the creep strength also was evaluated. Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis. A relationship was found between the fiber orientation and the creep strength.

Grobstein, T. L.↗
NASA NTRS1991

An overview of self-consistent methods for fiber-reinforced composites

The Walker et al. (1989) self-consistent method to predict both the elastic and the inelastic effective material properties of composites is examined and compared with the results of other self-consistent and elastically based solutions. The elastic part of their method is shown to be identical to other self-consistent methods for non-dilute reinforced composite materials; they are the Hill (1965), Budiansky (1965), and Nemat-Nasser et al. (1982) derivations. A simplified form of the non-dilute self-consistent method is also derived. The predicted, elastic, effective material properties for fiber reinforced material using the Walker method was found to deviate from the elasticity solution for the v sub 31, K sub 12, and mu sub 31 material properties (fiber is in the 3 direction) especially at the larger volume fractions. Also, the prediction for the transverse shear modulus, mu sub 12, exceeds one of the accepted Hashin bounds. Only the longitudinal elastic modulus E sub 33 agrees with the elasticity solution. The differences between the Walker and the elasticity solutions are primarily due to the assumption used in the derivation of the self-consistent method, i.e., the strain fields in the inclusions and the matrix are assumed to remain constant, which is not a correct assumption for a high concentration of inclusions.

Gramoll, Kurt C.↗
NASA NTRS1989

Morphological control of inter-penetrating polymer networks

Synthetic organic polymer chemistry has been successful in producing composition of matter with thermal oxidation stability and progressively higher glass transition temperatures. In part, this was done by increasing the steric-hindrance of moieties in the chain of a macromolecule. The resulting polymers are usually quite insoluble and produce molten polymers of very high viscosities. These types of polymers are not easily processed into graphite fiber prepregs by melt or solution impregnation methods. Hence, a technological need exists to produce new knowledge of how to produce polymer-fiber composites from this class of polymers. The concept of freeze drying amic-acid prepolymers with reactive thermoplastic was proposed as a research topic for the ASEE/NASA Summer Faculty Program of 1989 as a means of producing polymer-fiber composites. This process scheme has the thermodynamic attribute that the magnitude of phase separation due to differences in solubility of two organic constituents in solution will be greatly reduced by removing a solvent not by evaporation but by sublimation. Progress to date on evaluating this polymer processing concept is briefly outlined.

Hansen, Marion↗
DOE OSTI2025

Physically constrained 3D diffusion for inverse design of fiber-reinforced polymer composite materials

Designing fiber-reinforced polymer composites (FRPCs) with a tailored nonlinear stress-strain response is crucial for applications such as energy absorption in crash structures, flexible robotics, and impact-resistant protective gear. However, the inherent complexities of composite materials and the multitude of parameters involved, render traditional design and optimization methods inadequate for achieving effective inverse design of composites. In this paper, we present an AI-based inverse design framework that effectively and efficiently generates FRPCs with targeted nonlinear stress-strain responses. We introduce a physically constrained diffusion model (PC3D_Diffusion) capable of managing the complexities of composite materials and producing detailed, high-quality designs. We propose a loss-guided, learning-free approach to generate physically feasible microstructure designs by explicitly enforcing physical constraints during the generation process. For training purposes, 1.35 million FRPC samples were created, and their corresponding stress-strain curves were computed using established physics-based computational models. The results show that PC3D_Diffusion consistently generates high-quality designs with tailored mechanical behaviors, while guaranteeing compliance with the physical constraints. PC3D_Diffusion advances FRPC inverse design and may facilitate the inverse design of other 3D materials, offering potential applications in industries reliant on materials with custom mechanical properties.

Xu, Pei [Clemson Univ., SC (United States)]↗
NASA NTRS1992

Creep behavior of tungsten fiber reinforced niobium metal matrix composites

Tungsten fiber reinforced niobium metal matrix composites were evaluated for use in space nuclear power conversion systems. The composite panels were fabricated using the arc-spray monotape technique at the NASA Lewis Research Center. The creep behavior of W/Nb composite material was determined at 1400 and 1500 K in vacuum over a wide range of applied loads. The time to reach 1 percent strain, the time to rupture, and the minimum creep rate were measured. The W/Nb composites exceeded the properties of monolithic niobium alloys significantly even when compared creep strength also was evaluated. Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending the fiber orientation relative to the stress axis. A relationship was found between the fiber orientation and the creep strength.

Grobstein, Toni L.↗
NASA NTRS1990

Innovative design of composite structures: The use of curvilinear fiber format in composite structure design

The gains in structural efficiency are investigated that can be achieved by aligning the fibers in some or all of the layers in a laminate with the principal stress directions in those layers. The name curvilinear fiber format is given to this idea. The problem studied is a plate with a central circular hole subjected to a uniaxial tensile load. An iteration scheme is used to find the fiber directions at each point in the laminate. Two failure criteria are used to evaluate the tensile load capacity of the plates with a curvilinear format, and for comparison, counterpart plates with a conventional straightline fiber format. The curvilinear designs for improved tensile capacity are then checked for buckling resistance. It is concluded that gains in efficiency can be realized with the curvilinear format.

Hyer, M. W.↗
NASA NTRS1996

Low Temperature Mechanical Testing of Carbon-Fiber/Epoxy-Resin Composite Materials

The use of cryogenic fuels (liquid oxygen and liquid hydrogen) in current space transportation vehicles, in combination with the proposed use of composite materials in such applications, requires an understanding of how such materials behave at cryogenic temperatures. In this investigation, tensile intralaminar shear tests were performed at room, dry ice, and liquid nitrogen temperatures to evaluate the effect of temperature on the mechanical response of the IM7/8551-7 carbon-fiber/epoxy-resin system. Quasi-isotropic lay-ups were also tested to represent a more realistic lay-up. It was found that the matrix became both increasingly resistant to microcracking and stiffer with decreasing temperature. A marginal increase in matrix shear strength with decreasing temperature was also observed. Temperature did not appear to affect the integrity of the fiber-matrix bond.

Nettles, Alan T.↗
NASA NTRS2000

Mechanical properties and fiber type composition of chronically inactive muscles

A role for neuromuscular activity in the maintenance of skeletal muscle properties has been well established. However, the role of activity-independent factors is more difficult to evaluate. We have used the spinal cord isolation model to study the effects of chronic inactivity on the mechanical properties of the hindlimb musculature in cats and rats. This model maintains the connectivity between the motoneurons and the muscle fibers they innervate, but the muscle unit is electrically "silent". Consequently, the measured muscle properties are activity-independent and thus the advantage of using this model is that it provides a baseline level (zero activity) from which regulatory factors that affect muscle cell homeostasis can be defined. In the present paper, we will present a brief review of our findings using the spinal cord isolation model related to muscle mechanical and fiber type properties.

Non-NASA Center↗
NASA NTRS2012

Active Piezoelectric Vibration Control of Subscale Composite Fan Blades

As part of the Fundamental Aeronautics program, researchers at NASA Glenn Research Center (GRC) are investigating new technologies supporting the development of lighter, quieter, and more efficient fans for turbomachinery applications. High performance fan blades designed to achieve such goals will be subjected to higher levels of aerodynamic excitations which could lead to more serious and complex vibration problems. Piezoelectric materials have been proposed as a means of decreasing engine blade vibration either through a passive damping scheme, or as part of an active vibration control system. For polymer matrix fiber composite blades, the piezoelectric elements could be embedded within the blade material, protecting the brittle piezoceramic material from the airflow and from debris. To investigate this idea, spin testing was performed on two General Electric Aviation (GE) subscale composite fan blades in the NASA GRC Dynamic Spin Rig Facility. The first bending mode (1B) was targeted for vibration control. Because these subscale blades are very thin, the piezoelectric material was surface-mounted on the blades. Three thin piezoelectric patches were applied to each blade two actuator patches and one small sensor patch. These flexible macro-fiber-composite patches were placed in a location of high resonant strain for the 1B mode. The blades were tested up to 5000 rpm, with patches used as sensors, as excitation for the blade, and as part of open- and closed-loop vibration control. Results show that with a single actuator patch, active vibration control causes the damping ratio to increase from a baseline of 0.3% critical damping to about 1.0% damping at 0 RPM. As the rotor speed approaches 5000 RPM, the actively controlled blade damping ratio decreases to about 0.5% damping. This occurs primarily because of centrifugal blade stiffening, and can be observed by the decrease in the generalized electromechanical coupling with rotor speed.

Duffy, Kirsten P.↗
DOE OSTI2021

Processing and mechanical characterization of short carbon fiber-reinforced epoxy composites for material extrusion additive manufacturing

Fiber-reinforced polymer composites have been extensively utilized in recent years as feedstock materials for material extrusion additive manufacturing (AM) processes to improve strength, stiffness, and functionality of printed parts over unfilled printed polymers. However, the widespread adoption of AM of fiber-reinforced polymer composites requires a deeper understanding of the process-structure-property relationships in printed components, and such relationships are not well understood yet. Fiber length is critically important to the mechanical performance of short fiber composites, but very few studies to-date have focused on how the fiber length distribution (FLD) evolves during processing of composite feedstocks and how this evolution affects printing behavior and mechanical properties in 3D-printed composites. Here, FLD is measured for carbon fiber reinforced epoxy composites over a wide range of ink compositions and shear mixing times, and the distributions are fit with a Weibull-type distribution function. The effects of FLD on the tradeoff between ink processability, ink rheology, printing behavior and mechanical properties are investigated. Furthermore, the effects of printing parameters (nozzle size and print speed) on mechanical anisotropy and fiber orientation distribution (FOD) in printed composites are explored. Mechanical properties of printed composites are characterized via 3 pt-flexural testing, and microstructure is investigated using optical and scanning electron microscopy (SEM), and x-ray computed tomography. Finally, the fitted Weibull parameters are fed into a composite model that incorporates FLD and FOD, and model predictions are found to be in excellent agreement with experimental observations.

3D printing↗
NASA NTRS1982

Application of a gripping system to test a uniaxial graphite fiber reinforced composite /PMR 15/Celion 6000/ in tension at 316 C

A gripping system has been developed to test uniaxial, 0 deg orientation PMR 15/Celion 6000 composites at elevated temperatures. The method involves compression of grit-blasted laminate between grit-blasted metal to give a non-slipping interface for load transfer. Tensile testing at both 316 C and room temperature indicated that deformation was elastic to fracture and that the variation in tensile properties for one laminate is the same as that for several panels. In addition, the tensile properties for uniaxial PMR 15/Celion 6000 are identical at 316 C and room temperature. For nominally 51 volume percent fiber, the elastic modulus is 119.6 GPa, the fracture stress is 1370 MPa, and the strain to fracture is about 1.15 percent. In addition, data are presented which indicate that the gripping system can be used for long term, elevated temperature testing of composite materials.

Whittenberger, J. D.↗
NASA NTRS1980

The potential for damage from the accidental release of conductive carbon fibers from aircraft composites

Carbon and graphite fibers are known to be electrically conductive. The rapidly accelerating use of carbon fibers as the reinforcement in filamentary composite materials brought up the possibility of accidental release of carbon fibers from the burning of crashed commercial airliners with carbon composite parts. Such release could conceivably cause widespread damage to electrical and electronic equipment. The experimental and analytical results of a comprehensive investigation of the various elements necessary to assess the extent of such potential damage in terms of annual expected costs and maximum losses at low probabilities of occurrence are presented. A review of NASA materials research program to provide alternate or modified composite materials to overcome any electrical hazards from the use of carbon composites in aircraft structures is described.

Bell, V. L.↗
NASA NTRS1995

Composite Of Bisfuran/Bismaleimide With Graphite Fibers

Composite-material specimens made of graphite fibers and matrix composed of experimental copolymer of bismaleimide and bisfuran. Found to have mechanical and thermal properties comparable or superior to those of similar composite-material specimens. Candidates for use as lightweight structural components to replace metal components in high-temperature aircraft applications. Bismaleimides used widely for other purposes because of low cost and ease in fabrication. Mechanical properties equal or exceed those of composite made with commercial formulation.

Meador, Mary Ann B.↗
NASA NTRS1990

Hot filament technique for measuring the thermal conductivity of molten lithium fluoride

Molten salts, such as lithium fluoride, are attractive candidates for thermal energy storage in solar dynamic space power systems because of their high latent heat of fusion. However, these same salts have poor thermal conductivities which inhibit the transfer of heat into the solid phase and out of the liquid phase. One concept for improving the thermal conductivity of the thermal energy storage system is to add a conductive filler material to the molten salt. High thermal conductivity pitch-based graphite fibers are being considered for this application. Although there is some information available on the thermal conductivity of lithium fluoride solid, there is very little information on lithium fluoride liquid, and no information on molten salt graphite fiber composites. This paper describes a hot filament technique for determining the thermal conductivity of molten salts. The hot filament technique was used to find the thermal conductivity of molten lithium fluoride at 930 C, and the thermal conductivity values ranged from 1.2 to 1.6 W/mK. These values are comparable to the slightly larger value of 5.0 W/mK for lithium fluoride solid. In addition, two molten salt graphite fiber composites were characterized with the hot filament technique and these results are also presented.

Jaworske, Donald A.↗