SEARCH · Engineering Papers

Results for “elevation models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Estimation of the thickness of the Tharsis lava flows and implications for the nature of the topography of the Tharsis plateau

An attempt to estimate the thickness of the volcanics which cover the large part of the Tharsis region is reported. Estimates for the thickness of the flows were made using the numerous occurrences of the partially buried craters throughout the region and a relation between the crater diameter and crater rim height. Estimates were made along the southern contact with the heavily cratered terrain in the Phoenicis Lacus and Memnonia quadrangles, and along the northeast contact with older plains units in the Tharsis and Lunae Palus quadrangles. In these distal regions the thickness estimates range from 0 to 600-700 m of lava. This would indicate that only 20-30% of the topography is the result of volcanic construction. If the 20-30% estimate is representative of Tharsis as a whole then lava thickness would reach only 2-3 km near the center of the region. Thus only a small fraction of the topography presently observed can be attributed to units readily identifiable as volcanic. This additional evidence indicates that the model for Tharsis of a pre-existing elevated region of heavily cratered crust, capped by a veneer of volcanics is correct.

Plescia, J. B.↗

NASA NTRS1983

SSME main combustion chamber life prediction

Typically, low cycle fatigue life is a function of the cyclic strain range, the material properties, and the operating temperature. The reusable life is normally defined by the number of strain cycles that can be accrued before severe material degradation occurs. Reusable life is normally signified by the initiation or propagation of surface cracks. Hot-fire testing of channel wall combustors has shown significant mid-channel wall thinning or deformation during accrued cyclic testing. This phenomenon is termed cyclic-creep and appears to be significantly accelerated at elevated surface temperatures. This failure mode was analytically modelled. The cyclic life of the baseline SSME-MCC based on measured calorimeter heat transfer data, and the life sensitivity of local hot spots caused by injector effects were determined. Four life enhanced designs were assessed.

Cook, R. T.↗

NASA NTRS1989

Estimating forest productivity with Thematic Mapper and biogeographical data

Spectral data from the Landsat Thematic Mapper (TM) on three forest exosystems (the southern Illinois, the Great Smoky Mountains regions in Tennessee and North Carolina, and the central Adirondack Mountains in New York) were used in conjunction with ground-collected measures of forest productivity and such information as the area's slope, aspect, elevation, and soil and vegetation types, to develop models of regional forest productivity. It is shown that the models developed may be used to estimate the productivity of a region with a high degree of confidence, but that the reliability of single-pixel estimates is poor. The characteristics of a given ecosystem determine which spectral values are most closely related to forest productivity. Thus, mid-IR, NIR, and visible bands are most significant in Illinois and New York, while the thermal band is relatively more important in the Smokies.

Cook, Elizabeth A.↗

NASA NTRS1990

Status of the Delco Systems Operations forward looking windshear detection program

Delco Systems Operations, a division of General Motors Hughes Electronics Corporation, is developing a Forward Looking Windshear Detection System based on the integration of infrared remote sensing and accelerometer reactive sensing technologies. The infrared sensor is a multi-spectral, scanning radiometer operating in the 8 to 14 micron region. A 2 x 5 detector array with parallel-serial scanning produces 60 degrees horizontal and 10 degrees vertical-fields of view. Using multiple wavelength signals, azimuth temperature gradients are analyzed for characteristic signatures of thermally induced windshear phenomena. Elevation temperature gradients are processed through an atmosphere model to continuously compute a stability index for arming microburst detection criteria. The atmosphere model and proprietary computer processing algorithms combine to generate coarse estimates of disturbance ranges based on multiple wavelength radiance data with different extinction coefficients. Computer outputs of atmospheric stability, disturbance intensity, and azimuth and range information provide a situation display capability. A ground operated, experimental radiometer has been developed and is being used to verify the detection and discrimination concepts at an atmospheric and simulated rain test facility in Milwaukee. A prototype airborne radiometer is being developed for flight test evaluation during the summer of 1989.

Gallagher, Brian J.↗

NASA NTRS1991

Wrinkle ridges in Lunae Planum Mars - Implications for shortening and strain

Photoclinometric data for Lunae Planum wrinkle ridges indicate average relief of about 130 m and distinct elevation discontinuities across the ridge of 55 m. Modeling ridges as the result of thrust faulting and associated upper-plate folding indicates shortening across individual ridges of about 131 m (90 percent faulting). Total shortening at 20 N across Lunae Planum is about 1840 m corresponding to a regional compressive strain of 0.29 percent. Strain appears uniform across Lunae Planum, although it is accommodated by larger and fewer structures in the west than in the east.

Plescia, J. B.↗

NASA NTRS1993

Resolving topographic detail on Venus by modeling complex Magellan altimetry echoes

Magellan's altimeter is providing some of the finest resolution topography of Venus achieved to date. Nevertheless, efforts continue to improve the topographic resolution whenever possible. One effort to this end is stereoscopic imaging, which provides topography at scales similar to that of the synthetic aperture radar (SAR). However, this technique requires two SAR images of the same site to be obtained and limits the utility of this method. In this paper, we present another method to resolve topographic features at scales smaller than that of an altimeter footprint, which is more globally applicable than the stereoscopic approach. Each pulse which is transmitted by Magellan's altimeter scatters from the planet and echoes to the receiver, delayed based on the distance between the spacecraft and each surface element. As resolved in time, each element of an altimetry echo represents the sum of all points on the surface which are equidistant from the spacecraft. Thus, individual returns, as a function of time, create an echo profile which may be used to derive properties of the surface, such as the scattering law or, in this case, the topography within the footprint. The Magellan project has derived some of this information by fitting model templates to radar echo profiles. The templates are calculated based on Hagfor's Law, which assumes a smooth, gently undulating surface. In most regions these templates provide a reasonable fit to the observed echo profile; however, in some cases the surface departs from these simple assumptions and more complex profiles are observed. Specifically, we note that sub-footprint topographic relief apparently has a strong effect on the shape of the echo profile. To demonstrate the effects of sub-resolution relief on echo profiles, we have calculated the echo shapes from a wide range of simple topographic models. At this point, our topographic models have emphasized surfaces where only two dominant elevations are contained within a footprint, such as graben, ridges, crater rims, and central features in impact craters.

Lovell, Amy J.↗

NASA NTRS1995

Mobile user environment and satellite diversity for NGSO S-PCN's

The performance of satellite diversity under the influence of the mobile user environment is analyzed. To this end, a digital channel model is presented which takes into account the elevation angle as well as the user mobility in a given environment. For different LEO and MEO systems and for varying mobile user environments, some crucial benefits and drawbacks of satellite diversity are discussed. Specifically, the important GW service area concept is introduced. The conclusions are validated by numerical results from computer simulations. Globalstar (LEO) and Inmarsat (MEO) are compared in terms of visibility, service availability and equivalent handover complexity for different environments and user mobility.

Werner, Markus↗

NASA NTRS2003

Modeling of High-Strain-Rate Deformation, Fracture, and Impact Behavior of Advanced Gas Turbine Engine Materials at Low and Elevated Temperatures

Gamma titanium aluminides have received considerable attention over the last decade. These alloys are known to have low density, good high temperature strength retention, and good oxidation and corrosion resistance. However, poor ductility and low fracture toughness have been the key limiting factors in the full utilization of these alloys. More recently, Gamma-met PX has been developed by GKSS, Germany. These alloys have been observed to have superior strengths at elevated temperatures and quasi-static deformation rates and good oxidation resistance at elevated temperatures when compared with other gamma titanium aluminides. The present paper discusses results of a study to understand dynamic response of gamma-met PX in uniaxial compression. The experiments were conducted by using a modified split Hopkinson pressure bar between room temperature and 900 C and strain rates of up to 3500 per second. The Gamma met PX alloy showed superior strength when compared to nickel based superalloys and other gamma titanium aluminides at all test temperatures. It also showed strain and strain-rate hardening at all levels of strain rates and temperatures and without yield anomaly up to 900 C. After approximately 600 C, thermal softening is observed at all strain rates with the rate of thermal softening increasing dramatically between 800 and 900 C. However, these flow stress levels are comparatively higher in Gamma met PX than those observed for other TiAl alloys.

Shazly, Mostafa↗

NASA NTRS1997

Skeletal unloading inhibits the in vitro proliferation and differentiation of rat osteoprogenitor cells

Loss of weight bearing in the growing rat decreases bone formation, osteoblast numbers, and bone maturation in unloaded bones. These responses suggest an impairment of osteoblast proliferation and differentiation. To test this assumption, we assessed the effects of skeletal unloading using an in vitro model of osteoprogenitor cell differentiation. Rats were hindlimb elevated for 0 (control), 2, or 5 days, after which their tibial bone marrow stromal cells (BMSCs) were harvested and cultured. Five days of hindlimb elevation led to significant decreases in proliferation, alkaline phosphatase (AP) enzyme activity, and mineralization of BMSC cultures. Differentiation of BMSCs was analyzed by quantitative competitive polymerase chain reaction of cDNA after 10, 15, 20, and 28 days of culture. cDNA pools were analyzed for the expression of c-fos (an index of proliferation), AP (an index of early osteoblast differentiation), and osteocalcin (a marker of late differentiation). BMSCs from 5-day unloaded rats expressed 50% less c-fos, 61% more AP, and 35% less osteocalcin mRNA compared with controls. These data demonstrate that cultured osteoprogenitor cells retain a memory of their in vivo loading history and indicate that skeletal unloading inhibits proliferation and differentiation of osteoprogenitor cells in vitro.

NASA Discipline Musculoskeletal↗

NASA NTRS1958

Investigation of Incipient Spin Characteristics of a 1/35-Scale Model of the Convair F-102A Airplane, Coord. No. AF-AM-79

Incipient spin characteristics have been investigated on a l/35-scale dynamic model of the Convair F-10% airplane. The model was launched by a catapult apparatus into free flight with various control settings, and the motions obtained were photographed. The model was ballasted for the combat loading. All tests were made with the speed brakes and landing gear retracted, and engine effects were not simulated. The results of the investigation indicated that the model would enter motions apparently simulating entry phases of spins when the elevators were deflected full up. Deflecting the rudder had little effect on the direction of the motion obtained, but when ailerons were deflected the model always rotated in a direction opposite to the aileron setting (that is, the model entered a right spin with the stick to the left). The ailerons were very influential in initiating spin entry, and the pilot should avoid, as far as possible, the use of ailerons in low-speed flight.

Healy, Frederick M.↗

NASA NTRS2011

Processing and Characterization of Peti Composites Fabricated by High Temperature Vartm (Section)

The use of composites as primary structures on aerospace vehicles has increased dramatically over the past decade, but so have the production costs associated with their fabrication. For certain composites, high temperature vacuum assisted resin transfer molding (HT-VARTM) can offer reduced fabrication costs compared to conventional autoclave techniques. The process has been successfully used with phenylethynyl terminated imide (PETI) resins developed by NASA Langley Research Center (LaRC). In the current study, three PETI resins have been used to make test specimens using HT-VARTM. Based on previous work at NASA LaRC, larger panels with a quasi-isotropic lay-up were fabricated. The resultant composite specimens exhibited void contents of ~ 3% by volume depending on the type of carbon fabric preform used. Mechanical properties of the panels were determined at both room and elevated temperatures. Fabric permeability characterizations and limited process modeling efforts were carried out to determine infusion times and composite panel size limitations. In addition, new PETI based resins were synthesized specifically for HT-VARTM.

Ghose, Sayata↗

NASA NTRS2016

Quantifying the Contribution of Thermally Driven Recirculation to a High-Ozone Event Along the Colorado Front Range Using Lidar

A high-ozone (O3) pollution episode was observed on 22 July 2014 during the concurrent Deriving Information on Surface Conditions from Column and Vertically Resolved Observations Relevant to Air Quality (DISCOVER-AQ) and Front Range Air Pollution and Photochemistry Experiment (FRAPPE) campaigns in northern Colorado. Surface O3 monitors at three regulatory sites exceeded the Environmental Protection Agency (EPA) 2008 National Ambient Air Quality Standard (NAAQS) daily maximum 8h average (MDA8) of 75ppbv. To further characterize the polluted air mass and assess transport throughout the event, measurements are presented from O3 and wind profilers, O3-sondes, aircraft, and surface-monitoring sites. Observations indicate that thermally driven upslope flow was established throughout the Colorado Front Range during the pollution episode. As the thermally driven flow persisted throughout the day, O3 concentrations increased and affected high-elevation Rocky Mountain sites. These observations, coupled with modeling analyses, demonstrate a westerly return flow of polluted air aloft, indicating that the mountain-plains solenoid circulation was established and impacted surface conditions within the Front Range.

Front Range Air Pollution and Photochemistry Exper↗

NASA NTRS2025

Modeling and Simulation Credibility Assessments of Musculoskeletal Computational Models for Simulating Astronaut Injuries Due to a Poor Spacesuit Fit

The musculoskeletal (MS) system of astronauts is subject to physiological changes, potentially leading to injuries due to the exposure to different gravitational environments experienced during spaceflight. These injuries can occur while an astronaut is performing an Extravehicular Activity (EVA) in space, on lunar or planetary surfaces or while wearing a spacesuit during terrestrial training for an EVA. The OpenSim MS modeling software can assess EVA induced MS injury mechanisms such as muscle strains, ligament injuries and joint injuries. One area of concern, since there are only a few different spacesuit sizes with limited adjustability, is the possibility of a poorly fitting spacesuit. This can cause unnatural joint motions and torques resulting in various MS injuries. A credibility assessment of the OpenSim modeling and simulation procedures is performed per NASA-STD-7009A to provide information on the credibility of the model’s use in simulating EVA related injury mechanisms. The credibility assessment evaluated various OpenSim models against the following eight credibility factors: data pedigree, input pedigree, code verification, solution verification, conceptual validation, referent validation, results uncertainty and results robustness (sensitivity). The models evaluated for EVA injuries will require additional credibility factor analysis and upgrades to the model features, such as adding ligaments to a whole-body model, to reliably predict and analyze the EVA injuries expected to occur due to a poor spacesuit fit. The degree of elevation strategy required to increase the credibility assessment scores will depend on the model complexity and the injury mechanism.

Christopher A. Gallo↗

NASA NTRS2024

Modeling and Simulation Credibility Assessments of Musculoskeletal Computational Models for Simulating Astronaut Injuries Due to a Poor Spacesuit Fit

Christopher A Gallo↗

NASA NTRSDate not supplied

Mapping National Forest Aboveground Biomass in Mexico by Integrating GEDI, Sentinel‐1 and Sentinel‐2 Data

Accurate mapping of forest aboveground biomass density (AGBD) is required to better understand the role of forests in the global carbon cycle and to support international policies for climate change mitigation and adaptation. Mexico is one of the countries having great potential for the United Nations Programme on Reducing Emissions from Deforestation and Forest Degradation (or UN-REDD program) and there is a growing demand for unbiased Monitoring Reporting Verification systems at a national level. As an effort under NASA’s Carbon Monitoring System (CMS) program, we developed a machine learning model using multi-stream remote sensing measurements as well as topographic data to create a high spatial resolution AGBD map (~100 m) over Mexico (circa 2020). The remote sensing data includes Global Ecosystem Dynamic Investigation (GEDI) lidar, Sentinel 1 Synthetic-Aperture Radar (SAR), and Sentinel-2 multispectral imagery (MSI). GEDI onboard the International Space Station provides unprecedented forest structure and AGBD sampling datasets for model training and validation practices. Our analysis indicates that the developed random forest model can capture 63 % of the spatial variation (RMSE = 33.7 Mg/ha) of AGBD of Mexican forests. We find that shortwave infrared bands of Sentinel-2 MSI and topographical variables from elevation data are the most important variables in the developed AGBD model. Our study highlights methodological opportunities in synergistic uses of multiple sensors for large-scale forest AGBD mapping and shows potential for retrospective analysis and operational monitoring of forest AGBD and its dynamics.

Taejin Park↗

NASA NTRS1948

Hydrodynamic Characteristics of a Low-drag, Planing-tail Flying-boat Hull

The hydrodynamic characteristics of a flying-boat incorporating a low-drag, planing-tail hull were determined from model tests made in Langley tank number 2 and compared with tests of the same flying boat incorporating a conventional-type hull. The planing-tail model, with which stable take-offs were possible for a large range of elevator positions at all center-of-gravity locations tested, had more take-off stability than the conventional model. No upper-limit porpoising was encountered by the planing-tail model. The maximum changes in rise during landings were lower for the planing-tail model than for the conventional model at most contact trims, an indication of improved landing stability for the planing-tail model. The hydrodynamic resistance of the planing-tail hull was lower than the conventional hull at all speeds, and the load-resistance ratio was higher for the planing-tail hull, being especially high at the hump. The static trim of the planing-tail hull was much higher than the conventional hull, but the variation of trim with speed during take-off was smaller.

Suydam, Henry B↗

NASA NTRS1989

Do faculae blanket sunspots?

If the hillock model for faculae (plages), in which the faculae are structures elevated above the photosphere, is correct, faculae may blanket sunspots. In this paper, the appearance of sunspots in relation to faculae areas and disk position is analyzed, leading to the conclusion that faculae blanket sunspots preferentially near the sun's limb. A computer model fitting the observation is used to infer an average height of 200 km for faculae. The possibility that plages obstruct the sunspot view is ruled out.

Schatten, Kenneth H.↗

NASA NTRS2005

ICESat Observations of Topographic Change in the Northern Segment of the 2004 Sumatra-Andaman Islands Earthquake Rupture Zone

The Andaman Islands are located 120 km east of the Sunda trench in the northern quarter of the 1300 km long rupture zone of the 2004 Sumatra-Andaman Islands earthquake inferred from the distribution of aftershocks. Initial field reports indicate that several meters of uplift and up to a meter of submergence occurred on the western and eastern shorelines of the Andaman Islands, respectively, associated with the earthquake (Bilham, 2005). Satellite images also document uplift of western shoreline coral reef platforms above sea level. Body-wave (Ji, 2005; Yamamaka, 2005) and tide-gauge (Ortiz, 2005) slip inversions only resolve coseismic slip in the southern one-third to one-half of the rupture zone. The amount of coseismic slip in the Andaman Islands region is poorly constrained by these inversions. The Ice, Cloud, and land Elevation Satellite (ICESat), a part of the NASA Earth Observing System, is being used to document the spatial pattern of Andaman Islands vertical displacements in order to constrain models of slip distribution in the northern part of the rupture zone. ICESat carries the Geoscience Laser Altimeter System (GLAS) that obtains elevation measurements from 80 m diameter footprints spaced 175 m apart along profiles. For surfaces of low slope, single-footprint absolute elevation and horizontal accuracies of 10 cm and 6 m (1 sigma), respectively, referenced to the ITRF 2002 TOPEX/Poseidon ellipsoid are being obtained. Laser pulse backscatter waveforms enable separation of ground topography and overlying vegetation cover. During each 33-day observing period ICESat acquires three profiles crossing the Andaman Islands. A NNE-SSW oriented track consists of 1600 laser footprints along the western side of North, Middle, and South Andaman Islands and 240 laser footprints across the center of Great Andaman Island. Two NNW-SSE tracks consist of 440 footprints across Middle Andaman Island and 25 footprints across the west side of Sentinel Island. Cloud-free profiles were acquired in the fall of 2003 and 2004. During February-March, 2005 ICESat's precise pointing capability will be used to exactly repeat these three profiles, with a cross-track accuracy of better than 100 m, providing trench- parallel and -perpendicular observations of topographic change of the Andaman Islands that will compliment geodetic field surveys. The observed elevation changes will be compared to models of coseismic deformation associated with the mainshock and large aftershocks in the Andaman Islands region.

Harding, David↗