Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electronic damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Effect of proton irradiation dose on InAlN/GaN metal-oxide semiconductor high electron mobility transistors with Al 2 O 3 gate oxide

The effects of proton irradiation on the dc performance of InAlN/GaN metal-oxide-semiconductor high electron mobility transistors (MOSHEMTs) with Al 2 O 3 as the gate oxide were investigated. The InAlN/GaN MOSHEMTs were irradiated with doses ranging from 1×10 13 to 1×10 15 cm –2 at a fixed energy of 5MeV. There was minimal damage induced in the two dimensional electron gas at the lowest irradiation dose with no measurable increase in sheet resistance, whereas a 9.7% increase of the sheet resistance was observed at the highest irradiation dose. By sharp contrast, all irradiation doses created more severe degradation in the Ohmic metal contacts, with increases of specific contact resistance from 54% to 114% over the range of doses investigated. These resulted in source-drain current–voltage decreases ranging from 96 to 242 mA/mm over this dose range. The trap density determined from temperature dependent drain current subthreshold swing measurements increased from 1.6 × 10 13 cm –2 V –1 for the reference MOSHEMTs to 6.7 × 10 13 cm –2 V –1 for devices irradiated with the highest dose. In conclusion, the carrier removal rate was 1287 ± 64 cm –1 , higher than the authors previously observed in AlGaN/GaN MOSHEMTs for the same proton energy and consistent with the lower average bond energy of the InAlN.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

An Introduction to Radiation Damage in Minerals and Ceramics [Slides]

Radiation effects in minerals and ceramics are quite distinct from effects observed in metals. This is largely due to interactions between radiation and the electronic structure of insulating materials that are unique compared to metallic conductors. Most notably, insulators exhibit property changes when energetic particles lose energy to electrons in the solid, whereas metals are unaffected by electronic energy losses. In addition, displacive radiation damage effects (atoms being knocked off their lattice sites by energetic particles) are much more complex in insulators, due to the complexities of their crystal structures (multiple cation and anion sublattices). In this presentation, we will focus on the atomistic mechanisms responsible for radiation damage in minerals and ceramics, when energetic particles lose energy while penetrating a solid. We will consider several examples, including (i) irradiation induced color center formation in gemstones; (ii) latent defects in alkali halides (relevance to thermoluminescent detectors); (iii) radioactive decay-induced amorphization of natural minerals; and (iv) extended defect formation and phase stability in complex oxides.

36 MATERIALS SCIENCE↗

The Space Shuttle Program Pre-Flight Meteoroid and Orbital Debris Risk/Damage Predictions and Post-Flight Damage Assessments

The pre-flight predictions and postflight assessments carried out in relation to a series of Space Shuttle missions are reviewed, and data are presented for the meteoroid and orbital debris damage observed on the Hubble Space Telescope during the 1994 Hubble repair mission. Pre-flight collision risk analyses are carried out prior to each mission, and in the case of an unacceptable risk, the mission profile is altered until the risk is considered to be acceptable. The NASA's BUMPER code is used to compute the probability of damage from debris and meteoroid particle impacts based on the Poisson statistical model for random events. The penetration probability calculation requires information concerning the geometry of the critical systems, the penetration resistance and mission profile parameters. Following each flight, the orbiter is inspected for meteoroid and space debris damage. The emphasis is on areas such as the radiator panels, the windows and the reinforced carbon-carbon structures on the leading wing edges and on the nose cap. The contents of damage craters are analyzed using a scanning electron microscope to determine the nature and origin of the impactor. Hypervelocity impact tests are often performed to simulate the observed damage and to estimate the nature of the damaging particles. The number and type of damage observed provides information concerning the orbital debris environment.

Levin, George M.↗

Hair cell recovery in mitotically blocked cultures of the bullfrog saccule

Hair cells in many nonmammalian vertebrates are regenerated by the mitotic division of supporting cell progenitors and the differentiation of the resulting progeny into new hair cells and supporting cells. Recent studies have shown that nonmitotic hair cell recovery after aminoglycoside-induced damage can also occur in the vestibular organs. Using hair cell and supporting cell immunocytochemical markers, we have used confocal and electron microscopy to examine the fate of damaged hair cells and the origin of immature hair cells after gentamicin treatment in mitotically blocked cultures of the bullfrog saccule. Extruding and fragmenting hair cells, which undergo apoptotic cell death, are replaced by scar formations. After losing their bundles, sublethally damaged hair cells remain in the sensory epithelium for prolonged periods, acquiring supporting cell-like morphology and immunoreactivity. These modes of damage appear to be mutually exclusive, implying that sublethally damaged hair cells repair their bundles. Transitional cells, coexpressing hair cell and supporting cell markers, are seen near scar formations created by the expansion of neighboring supporting cells. Most of these cells have morphology and immunoreactivity similar to that of sublethally damaged hair cells. Ultrastructural analysis also reveals that most immature hair cells had autophagic vacuoles, implying that they originated from damaged hair cells rather than supporting cells. Some transitional cells are supporting cells participating in scar formations. Supporting cells also decrease in number during hair cell recovery, supporting the conclusion that some supporting cells undergo phenotypic conversion into hair cells without an intervening mitotic event.

Non-NASA Center↗

Modification of graphene properties due to electron-beam irradiation

The authors report micro-Raman investigation of changes in the single and bilayer graphene crystal lattice induced by the low and medium energy electron-beam irradiation (5-20 keV). It was found that the radiation exposures result in the appearance of the strong disorder D band around 1345 cm{sup -1}, indicating damage to the lattice. The D and G peak evolution with increasing radiation dose follows the amorphization trajectory, which suggests graphene's transformation to the nanocrystalline and then to amorphous form. The results have important implications for graphene characterization and device fabrication, which rely on the electron microscopy and focused ion beam processing.

36 MATERIALS SCIENCE↗

A high contrast method of unstained biological samples under a thin carbon film by scanning electron microscopy

The contrast of biological samples in scanning electron microscopy (SEM) is very weak. To examine a biological specimen by SEM, many steps and/or special equipment are required to prepare the sample. Here, we describe a method using an unstained biological sample under a 40 nm carbon film to give a high contrast image, where the image is detected by the secondary electron (SE) signal at a low accelerating voltage of 1.5 kV. Under these conditions, it is hard to detect a direct signal from a biological specimen. The high contrast image is created by the SEs from the lower surface of the thin carbon film. Therefore, the damage to the sample from the electron beam is very low. Our method can be utilized to observe various biological samples of bacteria, viruses, and protein complexes.

60 APPLIED LIFE SCIENCES↗

Detailed characterization of a PWR fuel rod at high burnup in support of LOCA testing

Experimental investigations of the fuel microstructure and volatile fission products along the pellet of a high burnup specimen (local burnup 76 GWd/tHM) have been conducted to support future transient testing. Detailed microscopy examinations have been carried out at different length scales. Transmission electron microscopy has highlighted a significant amount of damage across the entire radius with the formation of networks of dislocations. The optical and scanning electron microscopy determined the formation of three zones in the pellet with different characteristics. An intermediate region with no grain subdivision, lower porosity than the central zone porosity and high retained fission gas in nanometric bubbles and in the matrix was present between r/r0 ˜ 0.55 and 0.8. The high retention of gas in this region might suggest that the region will be prone to fine fragmentation, in addition to the HBS. An abrupt transition in the structure was observed at mid radius, with a third region developing from the mid radius to the pellet center. In this part of the pellet, metallic and grey phases with size between hundreds of nanometers and a few micrometers have formed at grain boundaries. The majority of fission gas has been released from the grain matrix and the original grains have polygonised, forming sub-grain domains separated by low-angle grain boundaries. No final explanation can be given for the polygonization occurring in the center, but on the basis of the irradiation history and the analysis of all the post irradiation examination (PIE) data, it is postulated that the polygonization within the original grains is an effect of dynamic recovery occurring at high temperature in the fuel center.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Tomographic investigation of fermi level pinning at focused ion beam milled semiconductor surfaces

Electron holography in the transmission electron microscope (TEM) offers the spatial and signal resolution for studying effects like Fermi level pinning or dopant concentration variations important for the design of modern electronic devices. To overcome the loss of information along the projection direction, surface effects, and surface damage due to TEM specimen preparation, we apply electron holographic tomography to analyze the 3D potential distribution of semiconductor samples prepared by focused-ion-beam. We observe mid-band gap pinning of the Fermi level at Si surfaces but valence band pinning at Ge surfaces. The pinning extends over tens of nanometers into the bulk.

36 MATERIALS SCIENCE↗

On the validity of equivalent electron fluence for GaAs solar cells

A simple model for particulate radiation damage in shallow-junction heteroface GaAs solar cells is used to evaluate the equivalent electron fluence concept especially in the sense of additivity of electron and proton exposure. It is found that spatial dependent factors for low-energy proton exposure results in a dose dependent equivalent fluence ratio so that additivity within the equivalent fluence concept is generally not possible.

Wilson, J. W.↗

Sidewall depletion in nano-patterned LAO/STO heterostructures

We have investigated the conductance of nanostructures fabricated from the quasi-two-dimensional electron gas (q2DEG) formed at the LaAlO{sub 3}/ SrTiO{sub 3} (LAO/STO) interface. Measurements were done at room temperature and at T=4.2 K. Our findings show that the fully industry compatible nano-patterning process conserves the conductivity except for a small temperature dependent sidewall depletion which we attribute to etch damage induced by the dry etching process.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Space radiation interaction mechanisms in materials

Models of charged-particle impact under conditions typical of the space environment are reported, with a focus on impact excitation and nuclear reactions, especially for heavy ions. Impact excitation is studied by using a global model for electronic excitation based on formal relations through the classical dielectric function to derive an approximation related to the local plasma (electron density distribution) within the atoms and molecules; and corrections to the model resulting from the nonfluid nature of this plasma are discussed. Nuclear reactions are studied by reducing quantum-mechanical treatment of this general N-body problem to an equivalent two-body problem that is solvable, and by comparing the results with experimental data. The equations for heavy-charged-particle transport are derived and solution techniques demonstrated. Finally, these methods of analysis are applied to study the change in the electrical properties of a GaAs semiconductor for photovoltaic applications; proton damage to GaAs crystals is found to arise from stable replacement defects and to be nonannealable, in contrast to electron-induced damage.

Wilson, J. W.↗

Single-particle structure determination by X-ray free-electron lasers: Possibilities and challenges

Single-particle structure recovery without crystals or radiation damage is a revolutionary possibility offered by X-ray free-electron lasers, but it involves formidable experimental and data-analytical challenges. Many of these difficulties were encountered during the development of cryogenic electron microscopy of biological systems. Electron microscopy of biological entities has now reached a spatial resolution of about 0.3 nm, with a rapidly emerging capability to map discrete and continuous conformational changes and the energy landscapes of biomolecular machines. Nonetheless, single-particle imaging by X-ray free-electron lasers remains important for a range of applications, including the study of large “electron-opaque” objects and time-resolved examination of key biological processes at physiological temperatures. After summarizing the state of the art in the study of structure and conformations by cryogenic electron microscopy, we identify the primary opportunities and challenges facing X-ray-based single-particle approaches, and possible means for circumventing them.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ionization Cross Sections and Dissociation Channels of the DNA Sugar-Phosphate Backbone by Electron Collisions

It has been suggested that the genotoxic effects of ionizing radiation in living cells are not caused by the highly energetic incident radiation, but rather are induced by less energetic secondary species generated, the most abundant of which are free electrons.' The secondary electrons will further react to cause DNA damage via indirect and direct mechanisms. Detailed knowledge of these mechanisms is ultimately important for the development of global models of cellular radiation damage. We are studying one possible mechanism for the formation cf DNA strand breaks involving dissociative ionization of the DNA sugar-phosphate backbone induced by secondary electron co!lisions. We will present ionization cross sections at electron collision energies between threshold and 10 KeV using the improved binary encounter dipole (iBED) formulation' Preliminary results of the possible dissociative ionization pathways will be presented. It is speculated that radical fragments produced from the dissociative ionization can further react, providing a possible mechanism for double strand breaks and base damage.

Dateo, Christopher↗

Burst annealing of high temperature GaAs solar cells

One of the major limitations of solar cells in space power systems is their vulnerability to radiation damage. One solution to this problem is to periodically heat the cells to anneal the radiation damage. Annealing was demonstrated with silicon cells. The obstacle to annealing of GaAs cells was their susceptibility to thermal damage at the temperatures required to completely anneal the radiation damage. GaAs cells with high temperature contacts and encapsulation were developed. The cells tested are designed for concentrator use at 30 suns AMO. The circular active area is 2.5 mm in diameter for an area of 0.05 sq cm. Typical one sun AMO efficiency of these cells is over 18 percent. The cells were demonstrated to be resistant to damage after thermal excursions in excess of 600 C. This high temperature tolerance should allow these cells to survive the annealing of radiation damage. A limited set of experiments were devised to investigate the feasibility of annealing these high temperature cells. The effect of repeated cycles of electron and proton irradiation was tested. The damage mechanisms were analyzed. Limitations in annealing recovery suggested improvements in cell design for more complete recovery. These preliminary experiments also indicate the need for further study to isolate damage mechanisms. The primary objective of the experiments was to demonstrate and quantify the annealing behavior of high temperature GaAs cells. Secondary objectives were to measure the radiation degradation and to determine the effect of repeated irradiation and anneal cycles.

Brothers, P. R.↗

Dose-rate dependence of damage buildup in 3 C -SiC

The influence of the defect generation rate on radiation damage processes in SiC remains poorly understood. Here, we use a combination of ion channeling and transmission electron microscopy to systematically study the dose-rate dependence of damage buildup in 3C-SiC bombarded in the temperature range of 25–200 °C with 500 keV Ar ions. The results reveal a pronounced dose-rate effect, whose magnitude increases close-to-linearly with temperature. When ion dose and temperature are held constant, the dose-rate dependence of the damage level is nonlinear, with saturation at high dose rates. Electron microscopy reveals that the average size of stable defect clusters increases with increasing dose rate. These findings have important implications for understanding and predicting radiation damage in SiC.

Bayu Aji, L. B. (ORCID:0000000315573023)↗

Solid Particle Erosion of a Plasma Spray – Physical Vapor Deposition Environmental Barrier Coating in a Combustion Environment

Environmental barrier coatings (EBCs) were developed to reduce the susceptibility of SiC-based composites to the rapid volatilization and surface recession that occurs in the presence of water vapor. Extensive research and development has been performed on EBCs, and their corresponding failure mechanisms under different environmental conditions. However, one key failure mechanism, solid particle erosion (SPE), has not been thoroughly investigated. As a result, the present work investigates the SPE behavior of a ytterbium disilicate (Yb2Si2O7) environmental barrier coating (EBC) deposited via plasma spray-physical vapor deposition (PS-PVD). Erosion testing was performed at elevated temperature (1,200 °C) in a simulated combustion environment at the NASA Glenn Research Center Erosion Burner Rig Facility. Alumina (Al2O3) particles were used as the eroding media. A range of particle kinetic energies and impingement angles were investigated along with the effect of coating surface roughness. The post-erosion damage morphology was characterized using scanning electron microscopy (SEM). The SPE behavior of the PS-PVD EBC was shown to be comparable to other EBC systems reported in the literature.

Solid particle erosion; environmental barrier coat↗

A simulation model of front-end electronics for high-precision timing measurements with low-gain avalanche detectors

Here, we report simulation results of a study aiming to optimize parameters of a detector that uses low-gain avalanche detectors (LGAD) for high-precision timing measurements. The detector is assumed to be composed of a 50μm LGAD sensor coupled to front-end readout electronics which is used to measure the time of arrival of minimum ionizing particles. The simulation includes modeling of signal fluctuations in the LGAD sensor, variations of the analog bandwidth and signal-to-noise ratio (SNR) of the front-end electronics, time bin quantization, and radiation damage of the LGAD sensors. Two approaches to measure the timestamp are considered: leading edge and constant fraction. Simulated LGAD pulses before irradiation, and after irradiation with neutron fluences of 5×10 14 n/cm 2 and 1×10 15 n/cm 2 , are studied. The time resolution for a 50μm LGADs was found to be 35 ps for front-end electronics bandwidths larger than 350 MHz and SNRs larger than 30. The time resolution at SNR of 30 for fluences of 5×10 14 n/cm 2 and 1×10 15 n/cm 2 were found to be 31 ps and 37 ps, respectively.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗