Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electronic configurations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Radioisotope Stirling Engine Powered Airship for Low Altitude Operation on Venus

The feasibility of a Stirling engine powered airship for the near surface exploration of Venus was evaluated. The heat source for the Stirling engine was limited to 10 general purpose heat source (GPHS) blocks. The baseline airship utilized hydrogen as the lifting gas and the electronics and payload were enclosed in a cooled insulated pressure vessel to maintain the internal temperature at 320 K and 1 Bar pressure. The propulsion system consisted of an electric motor driving a propeller. An analysis was set up to size the airship that could operate near the Venus surface based on the available thermal power. The atmospheric conditions on Venus were modeled and used in the analysis. The analysis was an iterative process between sizing the airship to carry a specified payload and the power required to operate the electronics, payload and cooling system as well as provide power to the propulsion system to overcome the drag on the airship. A baseline configuration was determined that could meet the power requirements and operate near the Venus surface. From this baseline design additional trades were made to see how other factors affected the design such as the internal temperature of the payload chamber and the flight altitude. In addition other lifting methods were evaluated such as an evacuated chamber, heated atmospheric gas and augmented heated lifting gas. However none of these methods proved viable.

Colozza, Anthony J.↗
NASA NTRS2014

Radioisotope Stirling Engine Powered Airship for Atmospheric and Surface Exploration of Titan

The feasibility of an advanced Stirling radioisotope generator (ASRG) powered airship for the near surface exploration of Titan was evaluated. The analysis did not consider the complete mission only the operation of the airship within the atmosphere of Titan. The baseline airship utilized two ASRG systems with a total of four general-purpose heat source (GPHS) blocks. Hydrogen gas was used to provide lift. The ASRG systems, airship electronics and controls and the science payload were contained in a payload enclosure. This enclosure was separated into two sections, one for the ASRG systems and the other for the electronics and payload. Each section operated at atmospheric pressure but at different temperatures. The propulsion system consisted of an electric motor driving a propeller. An analysis was set up to size the airship that could operate near the surface of Titan based on the available power from the ASRGs. The atmospheric conditions on Titan were modeled and used in the analysis. The analysis was an iterative process between sizing the airship to carry a specified payload and the power required to operate the electronics, payload and cooling system as well as provide power to the propulsion system to overcome the drag on the airship. A baseline configuration was determined that could meet the power requirements and operate near the Titan surface. From this baseline design additional trades were made to see how other factors affected the design such as the flight altitude and payload mass and volume.

Titan↗
NASA NTRS2017

P-Compensated and P-Doped Superlattice Infrared Detectors

Barrier infrared detectors configured to operate in the long-wave (LW) infrared regime are provided. The barrier infrared detector systems may be configured as pin, pbp, barrier and double heterostructrure infrared detectors incorporating optimized p-doped absorbers capable of taking advantage of high mobility (electron) minority carriers. The absorber may be a p-doped Ga-free InAs/InAsSb material. The p-doping may be accomplished by optimizing the Be doping levels used in the absorber material. The barrier infrared detectors may incorporate individual superlattice layers having narrower periodicity and optimization of Sb composition to achieve cutoff wavelengths of.about.10.mu.m.

Khoshakhlagh, Arezou↗
NASA NTRS1983

Lines of Fe XII sensitive to coronal electron density

Lines of Fe XII sensitive to coronal electron density are discussed. The lines appear in solar spectra obtained by the Naval Research Laboratory (NRL) slit spectograph flown on Skylab. These lines are due to transitions between levels of the 3s 2 3p 3 configuration and fall at the wavelengths 1242.03 A, 1349.38 A, 2169.03 A, 2405.71 A, and 2565.99 A. It is shown that the line at 2169.03 A is severely blended by a line of Ni II at heights less than 12 arcsec outside the solar limb. Above 12 arcsec the lines at 2169.03 and 2405.71 A are apparently unblended and can be used to derive electron densities. An average coronal electron pressure of 6 x 10 to the 14th/cu cm K is obtained. However, the emitting path lengths of the Fe XII lines, deduced using the electron densities and absolute intensities, are unrealistically large. The reason for this difficulty is unclear.

Feldman, U.↗
NASA NTRS2018

NASA Electric Aircraft Testbed (NEAT) Single-Aisle Transport Air Vehicle Hybrid Electric Tail-Cone Thruster Powertrain Configuration and Test Results

A key technical challenge is to establish a viable concept for a MW-class hybrid gas-electric propulsion system for a commercial transport aircraft. This includes developing aircraft propulsion system conceptual designs, integrating sub-systems, high efficiency/power density electric machines, flight-weight power system and electronics, and enabling materials in high voltage insulation, high frequency soft magnetics, and conductors. The primary benefit of this research is to diversify the current turbofan propulsion options to include hybrid electric propulsion elements that reduce energy usage, emissions, and noise. A reconfigurable powertrain testbed at NASA Glenn Research Center is described including test results from the initial 500 kW powertrain configuration.

Dyson, Rodger W.↗
NASA NTRS2010

Miniature Lightweight Ion Pump

This design offers a larger surface area for pumping of active gases and reduces the mass of the pump by eliminating the additional vacuum enclosure. There are three main components to this ion pump: the cathode and anode pumping elements assembly, the vacuum enclosure (made completely of titanium and used as the cathode and maintained at ground potential) containing the assembly, and the external magnet. These components are generally put in a noble diode (or differential) configuration of the ion pump technology. In the present state of the art, there are two cathodes, one made of titanium and the other of tantalum. The anodes are made up of an array of stainless steel cylinders positioned between the two cathodes. All the elements of the pump are in a vacuum enclosure. After the reduction of pressure in this enclosure to a few microns, a voltage is applied between the cathode and the anode elements. Electrons generated by the ionization are accelerated toward the anodes that are confined in the anode space by the axial magnetic field. For the generation of the axial field along the anode elements, the magnet is designed in a C-configuration and is fabricated from rare earth magnetic materials (Nd-B-Fe or Sm-Co) possessing high energy product values, and the yoke is fabricated from the high permeability material (Hiperco-50A composed of Fe-Co-V). The electrons in this region collide with the gas molecules and generate their positive ions. These ions are accelerated into the cathode and eject cathode material (Ti). The neutral atoms deposit on the anode surfaces. Because of the chemical activity of Ti, the atoms combine with chemically active gas molecules (e.g. N2, O2, etc.) and remove them. New layers of Ti are continually deposited, and the pumping of active gases is thus accomplished. Pumping of the inert gases is accomplished by their burial several atomic layers deep into the cathode. However, they tend to re-emit if the entrapping lattice atoms are sputtered away. For stable pumping of inert gases, one side of the cathode is made of Ta. Impaction on Ta produces energetic, neutral atoms that pump the inert gases on the anode structure at the peripheral areas of the cathodes (between anode rings). For inert gases stability, a post design has been implemented. Here, posts of cathode material (Ti) are mounted on the cathode. These protrude into the initial part of the anode elements. Materials sputtered from the posts condense on the anode assembly and on the cathode plane at higher rates than in the normal diodes due to enhanced sputtering at glancing angles from geometrical considerations. This increases pumping by burial. This post design has enhanced pumping rates for both active and inert gases, compared with conventional designs.

Sinha, Mahadeva P.↗
NASA NTRS1977

Quantitative determination of zero-gravity effects on electronic materials processing germanium crystal growth with simultaneous interface demarcation. Experiment MA-060

Experiment MA-060 was designed to establish the crystal growth and segregation characteristics of a melt in a directional solidification configuration under near zero-g conditions. The interface demarcation technique was incorporated into the experiment since it constitutes a unique tool for recording the morphology of the growth rate throughout solidification, and for establishing an absolute time reference framework for all stages of the solidification process. An extensive study was performed of the germanium crystals grown during the Apollo-Soyuz Test Project mission. It was found that single crystal growth was achieved and that the interface demarcation functioned successfully. There was no indication that convection driven by thermal or surface tension gradients was present in the melt. The gallium segregation, in the absence of gravity, was found to be fundamentally different in its initial and its subsequent stages from that of the ground-based tests. None of the existing theoretical models for growth and segregation can account for the observed segregation behavior in the absence of gravity.

Gatos, H. C.↗
NASA NTRS1993

SAR sensor electronics: T/R modules

A discussion concerning the architecture of transmit/receive (T/R) modules in synthetic aperture radar (SAR) systems is presented. Module requirements are discussed in the context of the following: requirements traceability; antenna configuration; and typical module specifications/requirements. Finally, module technology development in the L-, C-, and X-bands is discussed.

Hasan, Mohd A.↗
NASA NTRS2012

Aquarius Main Structure Configuration

The Aquarius/SAC-D Observatory is a joint US-Argentine mission to map the salinity at the ocean surface. This information is critical to improving our understanding of two major components of Earth's climate system - the water cycle and ocean circulation. By measuring ocean salinity from space, the Aquarius/SAC-D Mission will provide new insights into how the massive natural exchange of freshwater between the ocean, atmosphere and sea ice influences ocean circulation, weather and climate. Aquarius is the primary instrument on the SAC-D spacecraft. It consists of a Passive Microwave Radiometer to detect the surface emission that is used to obtain salinity and an Active Scatterometer to measure the ocean waves that affect the precision of the salinity measurement. The Aquarius Primary Structure houses instrument electronics, feed assemblies, and supports a deployable boom with a 2.5 m Reflector, and provides the structural interface to the SAC-D Spacecraft. The key challenge for the Aquarius main structure configuration is to satisfy the needs of component accommodations, ensuring that the instrument can meet all operational, pointing, environmental, and launch vehicle requirements. This paper describes the evolution of the Aquarius main structure configuration, the challenges of balancing the conflicting requirements, and the major configuration driving decisions and compromises.

Eremenko, Alexander↗
NASA NTRS1996

NASAwide electronic publishing system: Prototype STI electronic document distribution, stage-4 evaluation report

This evaluation report contains an introduction, seven chapters, and five appendices. The Introduction describes the purpose, conceptual frame work, functional description, and technical report server of the STI Electronic Document Distribution (EDD) project. Chapter 1 documents the results of the prototype STI EDD in actual operation. Chapter 2 documents each NASA center's post processing publication processes. Chapter 3 documents each center's STI software, hardware, and communications configurations. Chapter 7 documents STI EDD policy, practices, and procedures. The appendices, which arc contained in Part 2 of this document, consist of (1) STI EDD Project Plan, (2) Team members, (3) Phasing Schedules, (4) Accessing On-line Reports, and (5) Creating an HTML File and Setting Up an xTRS. In summary, Stage 4 of the NASAwide Electronic Publishing System is the final phase of its implementation through the prototyping and gradual integration of each NASA center's electronic printing systems, desktop publishing systems, and technical report servers to be able to provide to NASA's engineers, researchers, scientists, and external users the widest practicable and appropriate dissemination of information concerning its activities and the result thereof to their work stations.

Tuey, Richard C.↗
NASA NTRS1974

UCB current detector experiment on Swedish auroral payloads

A split Langmuir probe has been developed to make in situ measurements of ionospheric current density and plasma bulk flow. The probe consists of two conducting elements that are separated by a thin insulator that shield each other over a 2 pi solid angle, and that are simultaneously swept from negative to positive with respect to the plasma. By measuring the current to each plate and the difference current between plates, information is obtained on the plasma's current density, bulk flow, electron temperature, and density. The instrument was successfully flown twice on sounding rockets into auroral events. Measurement data indicate that the total auroral current configuration is composed of several alternating east and west electrojets associated with several alternating up and down Birkeland currents.

Mozer, F.↗
NASA NTRS1977

Coherent optical processing of synthetic aperture radar data

Consideration is given to the data processing algorithm used in synthetic aperture radar (SAR) systems. Examples are presented of radar imagery obtained with the ERIM X-band SAR system and processed with a precision optical processor. An optical recording of the data is the input to the coherent optical processing channel. The encoding technique, spatial format, and quality of the stored data are discussed. Several optical processor configurations are outlined, noting particularly the tilted-plane system. A scanning photodetector serves to convert the optical processor output image data into an electronic signal stream. Solid-state two-dimensional photodetector arrays may provide this function at increased speeds and with greater accuracy.

Cindrich, I.↗
NASA NTRS1979

Preliminary study, analysis and design for a power switch for digital engine actuators

Innovative control configurations using high temperature switches to operate actuator driving solenoids were studied. The impact on engine control system life cycle costs and reliability of electronic control and (ECU) heat dissipation due to power conditioning and interface drivers were addressed. Various power supply and actuation schemes were investigated, including optical signal transmission and electronics on the actuator, engine driven alternator, and inside the ECU. The use of a switching shunt power conditioner results in the most significant decrease in heat dissipation within the ECU. No overall control system reliability improvement is projected by the use of remote high temperature switches for solenoid drivers.

Beattie, E. C.↗
NASA NTRS1985

Preliminary investigation of the electrodynamics of a conducting tether

An introductory study of the properties of an electrically conducting tether flown from the shuttle is presented. Only a single configuration is considered: a vertical conductor moving normally across the Earth's field, connecting the shuttle to a large conducting balloon that passively extracts electrons from the ionosphere. The distortions in the plasma at maximum current collection are described, as are the local and distant wakes. Numerical values are given.

Thompson, W. B.↗
NASA NTRS1987

Volcanic control of the Io atmosphere and neutral and plasma torus

Rate equations for the column density of Io's atmosphere and the number density of neutral atoms and ions in the torus have been formulated in terms of surface sublimation and venting of volcanic gases, sputtering efficiency, thermal escape, and the plasma processes that take place in the torus which included electron impact ionization, charge exchange, and transport. In the limit of low volcanic activity, estimates of the densities can be obtained, and the baseline configuration that would exist in the absence of volcanic activity is found. Solution of the coupled steady state rate equations shows that the densities are sensitive, to a varying degree, to the level of Io volcanism. The steady state densities predicted by the model are consistent with a volcanic flux of no more than 10 to the 12th/sq cm per sec. This is significantly lower than the values obtained on the basis of resurfacing rates and appears to imply that surface lava flows play a major role in the resurfacing process.

Eviatar, Aharon↗
NASA NTRS1991

Laboratory experiments on the electrodynamic behavior of tethers in space

The transient current systems between tethered plasmas in a large magnetoplasma are investigated experimentally for extrapolation to electrodynamic tethers in space. The studies measure the perturbed magnetic fields and the current density associated with pulsed currents to electrodes in three-dimensional space and time. The electrodes excite electron whistlers because they produce fields that dominantly couple to electrons, allowing pulsed currents to propagate and disperse as whistler wave packets. The wave packets evolve into force-free, flux-ropelike field configurations, and a whistler 'wedge' is formed in the plasma due to 'eddy' currents caused by insulated tethers with dc currents. Substantial radiation into the whistler mode happens with moving VLF antennas as well as tethers, and the wave spread within the ray cone is the most significant characteristic event. The wave spread widens the current channel, incites current closure, and is also associated with a 'phantom loop' phenomenon.

Stenzel, Reiner L.↗