Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electron scattering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Deep Optical Switching on Subpicosecond Timescales in an Amorphous Ge Metamaterial

Active nanostructured optical components show promise as potential building blocks for novel light-based computing and data processing architectures. However, nanoscale all-optical switches that have low activation powers and high-contrast ultrafast switching have been elusive so far. Here, pump–probe measurements performed on amorphous-Ge-based micro-resonator metasurfaces that exhibit strong resonant modes in the mid-infrared are reported. Relative change is observed in transmittance of ΔT/T ≈ 1 with picosecond (down to τ ≈ 0.5 ps) free carrier relaxation rates, obtained with very low pump fluences of 50 μJ cm –2 . In this work, these observations are attributed to efficient free carrier promotion, affecting light transmittance via high quality-factor optical resonances, followed by an increased electron–phonon scattering of free carriers due to the amorphous crystal structure of Ge. Full-wave simulations based on a permittivity model that describes free-carrier damping through crystal structure disorder find excellent agreement with the experimental data. These findings offer an efficient and robust platform for all-optical switching at the nanoscale.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mapping Thermoelectric Transport in a Multicomponent Alloy Space

Abstract Interest in high entropy alloy thermoelectric materials is predicated on achieving ultralow lattice thermal conductivity κ L through large compositional disorder. However, here it is shown that for a given mechanism, such as mass contrast phonon scattering, κ L will be minimized along the binary alloy with highest mass contrast, such that adding an intermediate mass atom to increase atomic disorder can increase thermal conductivity. Only when each component adds an independent scattering mechanism (such as adding strain fluctuation to an existing mass fluctuation) is there a benefit. In addition, both charge carriers and heat‐carrying phonons are known to experience scattering due to alloying effects, leading to a trade‐off in thermoelectric performance. Analytic transport models are applied, based on perturbation and effective medium theories, to predict how alloy scattering will affect the thermal and electronic transport across the full compositional range of several pseudo‐ternary and pseudo‐quaternary alloy systems. To do so, a multicomponent extension is demonstrated to both thermal and electronic binary alloy scattering models based on the virtual crystal approximation. Finally, it is shown that common functional forms used in computational thermodynamics can be applied to this problem to further generalize the scattering behavior that is modeled.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Earth-scattering induced modulation in low-threshold dark matter experiments

Dark matter particles with sufficiently large interactions with ordinary matter can scatter in the Earth before reaching and scattering in a detector. This induces a modulation in the signal rate with a period of one sidereal day. We calculate this modulation for sub-GeV dark matter particles that interact either with a heavy or an ultralight dark-photon mediator and investigate the resulting signal in low-threshold detectors consisting of silicon, xenon, or argon targets. The scattering in the Earth is dominated by dark matter scatters off nuclei, while the signal in the detector is easiest to observe from dark matter scattering off electrons. We investigate the properties of the modulation signal and provide projections of the sensitivity of future experiments. We find that a search for a modulation signal can probe new regions of parameter space near the energy thresholds of current experiments, where the data are typically dominated by backgrounds.

Models for Dark Matter↗
DOE OSTI2023

Deformation and Fracture Behavior of Additively Manufactured 316L Stainless Steel

Tensile deformation and fracture behavior of an additively manufactured (AM) 316L stainless steel (SS) in the as-built, stress-relieved, and solution-annealed conditions was investigated using in situ tensile testing in a scanning electron microscope with an electron back scattering diffraction (SEM–EBSD) detector. Analyses were performed to discuss the characteristic deformation and fracture process of the fine-grained AM 316L SS with and without relaxation heat treatment. The as-built 316L showed the highest strength, and both post-build heat treatments lowered the strength of the alloy. Regardless of the post-build processing, the AM 316L SS showed overall higher strength but slightly lower ductility when compared to the wrought (WT) 316L SS. Analysis of EBSD data indicated that the characteristic microstructural features from AM, such as the complex and fine grain morphology, dislocation network, pores, and silicon-rich oxides, evolved and exerted various roles during the tensile deformation and fracture processes. Further, it was obvious that the interaction of dislocation slips with oxide particles and cavities (or pores) resulted in an accelerated cracking in AM 316L SS. Overall, however, their influence on mechanical behavior was limited, as the genuinely high ductility of 316L SS could help avoid any premature or brittle fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Electron transport in gaseous detectors with a Python-based Monte Carlo simulation code

Understanding electron drift and diffusion in gases and gas mixtures is a topic of central importance for the development of modern particle detection instrumentation. The industry-standard MagBoltz code has become an invaluable tool during its 20 years of development, providing capability to solve for electron transport (‘swarm’) properties based on a growing encyclopedia of built-in collision cross sections. We have made a refactorization of this code from FORTRAN into Cython, and studied a range of gas mixtures of interest in high energy and nuclear physics. The results from the new open source PyBoltz package match the outputs from the original MagBoltz code, with comparable simulation speed. An extension to the capabilities of the original code is demonstrated, in implementation of a new Modified Effective Range Theory interface. We hope that the versatility afforded by the new Python code-base will encourage continued use and development of the MagBoltz tools by the particle physics community.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Investigation of phase-transformation path in TiZrHf(VNbTa)x refractory high-entropy alloys and its effect on mechanical property

Refractory high-entropy alloys (RHEAs) show a great potential as structural materials due to their remarkable properties, such as high strength and thermal stability. Despite these advantages, the RHEAs still suffer from the limited ductility at room temperature. To overcome the strength-ductility trade-off, the new RHEA design strategy, transformation-induced plasticity (TRIP) HEAs, have been developed by applying metastability-engineering approach. With the newly developed RHEAs design strategy, we designed metastable RHEAs, TiZrHfVxNbxTax (x = 1.0, 0.5 and 0.1) with decrease of the β-stabilizing elements (V, Nb, and Ta) to promote the transformation-induced ductility and work-hardening capability. The proper addition of the β-stabilizing elements (V, Nb, and Ta) into the ternary equi-molar TiZrHf alloy (TiZrHfV 0.1 Nb 0.1 Ta 0.1 ) leads to stress/strain-induced phase transformation from the body-centered cubic (BCC) to hexagonal-close-packed (HCP) α' and/or orthorhombic α" phases. Here, detailed studies on the phase transformation sequence during the deformation were carried out using X-ray diffraction (XRD), electron back-scattered diffraction (EBSD), and transmission-electron microscope (TEM), which revealed the stepwise phase transformation that is responsible for the strong strain hardening behavior. Furthermore, we further suggested the new transformation-induced-plasticity (TRIP) HEA design strategy, applying the Bo-Md approach.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of temperature on the fatigue cracking mechanisms in A356 Al alloy

This work builds on our previous investigation of the room temperature fatigue cracking mechanisms of an A356 Al alloy. Here, we analyze the elevated temperature fatigue cracking mechanisms in cast and friction stir processed (FSP) A356, and contrast them with the room temperature behavior. Two sets of FSP parameters were used to modify the microstructure of the cast alloy. After heat treatment, both the FSPed microstructures exhibited severe abnormal grain growth (AGG) leading to a very wide grain size distribution (from a few microns to a few millimeters). During room temperature fatigue tests, the FSP conditions exhibited significant improvements in fatigue lives, even up to an order of magnitude. However, with increasing temperature, the difference in the performance of the FSPed and Cast microstructures decreased until, at 200 °C, all three microstructural conditions exhibited similar fatigue response. Detailed electron back scattered diffraction (EBSD) imaging of failed fatigue specimens was used to study crack behavior. At room temperature, cracks initiated at defect sites or along persistent slip bands (PSBs) and propagated transgranularly. The grain boundaries acted as barriers to crack growth. At elevated temperatures, there was a complete role reversal of the grain boundaries. Cracks initiated along grain boundaries and propagated intergranularly in all microstructures. Below, we explore this transition of the cracking mechanism in detail.

Nelaturu, Plalgun↗
DOE OSTI2022

Geometric compatibility measure m' for twin transmission: A predictor or descriptor?

In this work, the geometric compatibility factor m' is critically analyzed to assess whether it can be used to interpret/predict twin transmission (TT) across grain boundaries (GBs). This geometric measure is widely used to relate the likelihood of TT to the misalignment of both the shear and plane-normal directions within a twin set (i.e., incoming and outgoing twin). Here, using a large set of electron back scattering diffraction (EBSD) data, a detailed statistical analysis of twin-GB interactions is performed for {${1\bar{01}}2$} tensile twins in hexagonal close-packed (HCP) metals Mg, Zr, and Ti at different strain levels. In addition, a full-field crystal plasticity model is employed to quantify the role of local stresses and the applicability of m' as a criterion for the TT process. This combined study addresses the following three main questions: (i) What is the fidelity of m' in describing experimentally observed TTs? (ii) Can m' be used as a metric to predict/anticipate TT? (iii) Does m' naturally capture local stress effects? As a descriptor, m' cannot rationalize ~25% of TT events observed in Mg or more than 50% of TT events in Zr and Ti. As a predictor, the m'-measure does not predict TT events in over ~50% of twin-GB interactions analyzed. Further, the applicability of m' to describe and predict TT events decreases with an increase in elastic anisotropy, plastic anisotropy, and macroscopic strain levels. Finally, the twinning simulations reveal that m' does not capture the key effects of local stresses on variant selection upon twin transmission. The local stress induced by the twinning shear transformation plays a dominant role in driving the TT process compared to the geometric alignment of the constituting twins, i.e., m'.

36 MATERIALS SCIENCE↗
DOE OSTI2020

A liquid hydrogen target for the MUSE experiment at PSI

A 280 ml liquid hydrogen target has been constructed and tested here for the MUSE experiment at PSI to investigate the proton charge radius via simultaneous measurement of elastic muon–proton and elastic electron–proton scattering. To control systematic uncertainties at a sub-percent level, strong constraints were put on the amount of material surrounding the target and on its temperature stability. The target system was successfully operated during a commissioning run at PSI at the end of 2018. The target temperature was stable at the 0.01 K level. This indicates a density stability at the 0.02% level, which is about a factor of ten better than required.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Simulation of the spatial shift in detector response for polarized protons within a calorimeter

Measurement of the helicity dependent elastic electron-proton scattering cross section provides a key means of investigating parity violation within the proton. However, such measurements exhibit potential instrumental effects associated with the detection of polarized recoiled protons. In particular, spin-orbit interactions within a massive detector induce a systematic spatial shift in the detector signal. In this study, we determine the size of this shift using the Geant4 simulation toolkit. For a typical hadron calorimeter, we found a polarization dependent shift on the order of 0.01-0.1 mm, multiple orders of magnitude smaller than the typical spatial resolution seen in hadronic calorimeters. Additionally, we provide the custom modifications required of the Geant4 source code to implement the quasi-elastic scattering of polarized protons incident on nuclei in the detector. The modifications are readily extendable to generic matter sources, and can be used for the study of additional spin dependent observables in Geant4.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Intrinsic energy and time resolution of the Jefferson Lab Hall C Neutral Particle Spectrometer

The Neutral Particle Spectrometer (NPS) is an advanced calorimeter designed to measure neutral electro- magnetic particles with high precision in energy, time, and position, under conditions of high luminosity and significant background. Integrated into the experimental setup of Hall C at Thomas Jefferson National Accelerator Facility, the NPS plays a critical role in studies of nucleon structure through exclusive and semi- inclusive reaction channels. Here, this paper presents an assessment of the detector’s performance characteristics, specifically its energy and timing resolution, derived from elastic electron–proton scattering data. We report an energy resolution between 1.2% and 1.3% in the 4.5–7.3 GeV range, and an intrinsic timing resolution better than 200 ps for energies above 500 MeV. These results serve as a reference for current and future precision measurements in hadronic physics.

Detector performance↗
DOE OSTI2025

Nuclear fragmentation at the future electron-ion collider

We explore the potential of conducting low-energy nuclear physics studies, including nuclear structure and decay, at the future Electron-Ion Collider (EIC) at Brookhaven. By comparing the standard theory of electron-nucleus scattering with the equivalent photon method applied to Ultraperipheral Collisions (UPC) at the Large Hadron Collider (LHC) at CERN. In the limit of extremely high beam energies and small energy transfers, very transparent equations emerge. We apply these equations to analyze nuclear fragmentation in UPCs at the LHC and 𝑒𝐴 scattering at the EIC, demonstrating that the EIC could facilitate unique photonuclear physics studies. Furthermore, we have also shown that the fragmentation cross-sections at the EIC are about 1,000 times smaller than those at the LHC. At the LHC, the fragmentation of uranium nuclei displays characteristic double-hump mass distributions from fission events, while at the EIC, fragmentation is dominated by neutron emission and fewer few fission products, about 10,000 smaller number of events.

Bertulani, Carlos A. [East Texas A&M University, C↗
DOE OSTI2021

Self-Assembly of Flexible Linear–Semiflexible Bottlebrush–Flexible Linear Triblock Copolymers

Block copolymer (BCP) self-assembly is a fundamental process in which incompatible blocks spontaneously form organized microstructures with broad practical applications. Classical understanding is that the domain spacing is limited by the contour length of the polymer backbone. Here, using a combination of molecular design, chemical synthesis, small-/wide-angle X-ray scattering, transmission electron microscopy, and electron tomography, we discover that this molecular picture does not hold for architecturally semiflexible BCPs. For strongly segregated linear–semiflexible bottlebrush–linear triblock copolymers, the size of the bottlebrush domain can be twice the bottlebrush backbone contour length. The mechanism of such anomalous self-assembly is likely that the interfacial repulsion between the incompatible blocks is large enough to pull a part of the linear end blocks into the bottlebrush domain. This effectively increases the bottlebrush domain size. Moreover, the semiflexible bottlebrush widens the regime for the cylinder morphology that is associated with the volume fraction of the end blocks fC SFB ∈ (0.10, >0.41). This window is much wider than that for flexible linear BCPs, fC F ∈ (0.14, 0.35), and that predicted by the recent self-consistent field theory for linear-bottlebrush BCPs of the same chemistry and molecular architecture. Finally, our experimental findings reveal previously unrecognized mechanisms for the self-assembly of architecturally complex BCPs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Excitation-Dependent High-Lying Excitonic Exchange via Interlayer Energy Transfer from Lower - to - Higher Bandgap 2D Material

High light absorption (~15%) and strong photoluminescence (PL) emission in monolayer (1L) transition metal dichalcogenides (TMDs) make them ideal candidates for optoelectronic device applications. Competing interlayer charge transfer (CT) and energy transfer (ET) processes control the photocarrier relaxation pathways in TMD heterostructures (HSs). In TMDs, long-distance ET can survive up to several tens of nm, unlike the CT process. Our experiment shows that an efficient ET occurs from the 1Ls WSe 2 -to-MoS 2 with an interlayer hexagonal boron nitride (hBN), due to the resonant overlapping of the high-lying excitonic states between the two TMDs, resulting in enhanced HS MoS 2 PL emission. This type of unconventional ET from the lower-to-higher optical bandgap material is not typical in the TMD HSs. With increasing temperature, the ET process becomes weaker due to the increased electron–phonon scattering, destroying the enhanced MoS 2 emission. Our work provides new insight into the long-distance ET process and its effect on the photocarrier relaxation pathways.

2D material↗
DOE OSTI2023

Single Ion Conducting Hairy Nanoparticle Additive to Improve Cycling Stability of Solid Polymer Electrolytes

The development of a solid electrolyte that can impede dendrite growth while still maintaining an appropriate level of conductivity is essential for improving performance of solid-state Li-ion battery. In this paper, we report the synthesis of single Li-ion conducting hairy nanoparticle (NP) materials that improved the cycling stability of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-doped poly(ethylene oxide) (PEO) solid electrolyte without significant reduction in conductivity. To unveil mechanisms leading to improved cycling stability, several characterization techniques including broadband dielectric spectroscopy, differential scanning calorimetry, small angle X-ray scattering, transmission electron microscopy, and shear rheology were used to study properties of polymer composites (PC) with added hairy NPs. It was found that hairy NPs influenced the Li/electrolyte interface and improved mechanical properties of bulk composites, all of which contributed to homogenous Li plating and stripping. The improved performance has been found in composites with concentrations of 4.8 and 9.1 weight % of added hairy NPs, which enabled Li cycling stability at 0.2 mA cm–2 critical current density (>300 h) that was otherwise not possible in either PEO-LiTFSI alone or PEO-LiTFSI composites containing a polymer identical to that attached to hairy NPs. Based on the discovered ability of hairy NP to influence bulk and interfacial properties of solid electrolyte, their use as additives is expected to be equally effective in reducing dendrite formation in other electrolytes relevant for the design of solid-state battery.

25 ENERGY STORAGE↗
DOE OSTI2026

Facet Preferencing by Chemical Substitution Controls Semi-Hydrogenation Selectivity in Ternary Pyrite-Type Intermetallic Compounds

Intermetallic compounds serve as model catalysts for selective hydrogenation reactions, offering precise control over the active site composition(s), geometric and electronic structure. The addition of a third element to form a ternary intermetallic alters the exposed crystal facet(s), demonstrating a strategy to impart improved catalytic behavior in intermetallic catalysts. The site-specific substitution of a small fraction of Pd atoms with Au in pyrite-type PdSb 2 results in the preferential exposure of the (100) facet over the (111) facet. Electron back scattered diffraction and density functional theory calculations confirm the facet change upon the substitution of Pd with Au to form the ternary Pd 1−x Au x Sb 2 (0.075 ≤ x ≤ 0.25). The (100) facet demonstrates higher net alkene selectivity due to significantly weaker alkene binding compared to the (111) facet. Distinct from our prior work on chemical substitution to directly alter the active site composition, this work demonstrates the indirect modification of active sites via preferential facet exposure.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗