Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Thermal Conductances Of Cold Metal Contacts Below 6 K

Conductances vary with temperature according to simple power law. Report presents data on thermal conductances of pure aluminum and stainless-steel 304 contact pairs. Data cover contacts with surface finishes of 0.1- to 1.6-micrometer root-mean-square roughness at temperatures from 1.6 to 6.0 K, under applied contact forces up to 670 N. Such data needed for optimal design of bolted joints in cryogenic instruments, particularly infrared instruments and focal-plane sensors.

Salerno, L. J.↗

Time domain scattering and radar cross section calculations for a thin, coated perfectly conducting plate

Radar cross section (RCS) calculations for flat, perfectly conducting plates are readily available through the use of conventional frequency domain techniques such as the Method of Moments (MOM). However, if the plate is covered with a dielectric material that is relatively thick in comparison with the wavelength in the material, these frequency domain techniques become increasingly difficult to apply. We present the application of the Finite Difference Time Domain (FDTD) Technique to the problem of electromagnetic scattering and RCS calculations from a thin, perfectly conducting plate that is coated with a thick layer of lossless dielectric material. Both time domain and RCS calculations are presented and disclosed.

Luebbers, Raymond J.↗

Conical cut radar cross section calculations for a thin, perfectly conducting plate

Radar Cross Section (RCS) calculations for flat, perfectly conducting plates are readily available through the use of conventional frequency domain techniques such as the Method of Moments. However, if time domain scattering or wideband frequency domain results are desired, then the Finite Difference Time Domain (FDTD) technique is a suitable choice. In this paper, we present the application of the Finite Difference Time Domain (FDTD) technique to the problem of electromagnetic scattering and RCS calculations from a thin, perfectly conducting plate for a conical cut in the scattering angle phi. RCS calculations versus angle phi will be presented and discussed.

Luebbers, Raymond J.↗

Conical cut radar cross section calculations for a thin, perfectly conducting plate

Radar cross section (RCS) calculations for flat, perfectly conducting plates are readily available through the use of conventional frequency domain techniques such as the method of moments. However, if time domain scattering or wideband frequency domain results are desired, then the finite difference time domain (FDTD) technique is a suitable choice. We present the application of the FDTD technique to the problem of electromagnetic scattering and RCS calculations from a thin, perfectly conducting plate for a conical cut in the scattering angle phi. RCS calculations versus angle phi are presented and discussed.

Luebbers, Raymond J.↗

Corrosion-protective coatings from electrically conducting polymers

In a joint effort between NASA Kennedy and LANL, electrically conductive polymer coatings were developed as corrosion protective coatings for metal surfaces. At NASA Kennedy, the launch environment consist of marine, severe solar, and intermittent high acid and/or elevated temperature conditions. Electrically conductive polymer coatings were developed which impart corrosion resistance to mild steel when exposed to saline and acidic environments. Such coatings also seem to promote corrosion resistance in areas of mild steel where scratches exist in the protective coating. Such coatings appear promising for many commercial applications.

Thompson, Karen Gebert↗

Time domain scattering and radar cross section calculations for a thin, coated perfectly conducting plate

Radar cross section (RCS) calculations for flat, perfectly conducting plates are readily available through the use of conventional frequency domain techniques such as the Method of Moments (MOM). However, if the plate is covered with a dielectric material that is relatively thick in comparison with the wavelength in the material, these frequency domain techniques become increasingly difficult to apply. The application is presented of the Finite Difference Time Domain (FDTD) technique to the problem of electromagnetic scattering and RCS calculations from a thin, perfectly conducting plate that is coated with a thick layer of lossless dielectric material. Both time domain and RCS calculations are presented and discussed.

Luebbers, Raymond J.↗

Results from the LDEF/A0076 cascaded variable conductance heatpipe experiment

The A0076 Variable Conductance Heat Pipe Experiment (CVCHPE) on the Long Duration Exposure Facility (LDEF) demonstrated temperature control better than +/- 0.3 C during fifty days on on-orbit data collection in a widely varying external environment. The experiment used two series connected, dry reservoir variable conductance heat pipes which require no electrical power for operation. The heat pipes used a central artery design with ammonia working fluid and nitrogen control gas. The LDEF was in orbit for almost six years rather than the planned one year mission. Although no additional data were taken during this extended period, post-test data indicated that the set point drifted upward less than 1 C per year. There were significant changes to the appearance of all external thermal control surfaces primarily due to atomic oxygen degradation, and one small anomaly in the electronics. These changes, though, had little effect on the CVCHPE performance.

Grote, Michael G.↗

Boundary formulations for shape sensitivity of temperature dependent conductivity problems

Used in concert with the Kirchhoff transformation, implicit differentiation of the discretized boundary integral equations governing the conduction of heat in solids with temperature dependent thermal conductivity is shown to generate an accurate and economical approach for computation of shape sensitivities. For problems with specified temperature and heat flux boundary conditions, a linear problem results for both the analysis and sensitivity analysis. In problems with either convection or radiation boundary conditions, a nonlinear problem is generated. Several iterative strategies are presented for the solution of the resulting sets of nonlinear equations and the computational performances examined in detail. Multizone analysis and zone condensation strategies are demonstrated to provide substantive computational economies in this process for models with either localized nonlinear boundary conditions or regions of geometric insensitivity to design variables. A series of nonlinear example problems is presented that have closed form solutions. Exact analytical expressions for the shape sensitivities associated with these problems are developed and these are compared with the sensitivities computed using the boundary element formulation.

Kane, James H.↗

Extremely low thermal conductivity of amorphous ice - Relevance to comet evolution

The thermal conductivity of very slowly deposited amorphous ice derived from experimental results is shown to be a factor of 0.0001 to 0.00001 less than hitherto estimated. Using the exceedingly low value of the thermal conductivity of comets deduced from the amorphous ice properties leads to the expectation that internal heating of comets is negligible below the outer several tens of centimeters.

Kouchi, A.↗

Electronic energy gap of molecular hydrogen from electrical conductivity measurements at high shock pressures

Electrical conductivities were measured for liquid D2 and H2 shock compressed to pressures of 10-20 GPa (100-200 kbar), molar volumes near 8 cu cm/mol, and calculated temperatures of 2900-4600 K. The semiconducting energy gap derived from the conductivities is 12 eV, in good agreement with recent quasi-particle calculations and with oscillator frequencies measured in diamond-anvil cells.

Nellis, W. J.↗

The effective thermal conductivity of an adsorbent - Praseodymium cerium oxide

The results of an experimental study to determine the effective thermal conductivity of praseodymium cerium oxide are reported. Praseodymium cerium oxide is an adsorbent used in the development of adsorption compressors for spaceborne refrigeration systems. A guarded-hot-plate apparatus was built for this study. Measurements were carried out for mean temperatures ranging from 300 to 600 C under a vacuum of 10 exp -5 torr. For the temperature range studied, the effective thermal conductivity increased from 0.14 to 0.76 W/m per C with increasing temperature, while displaying a cubic temperature dependency.

Secary, J. J.↗

Electrical Conductivity Of Diamond Up To 1,200 Degrees C

Report discusses measurements of electrical conductivities of two synthetic diamond films, three synthetic diamondlike films, and two natural type IIa diamonds at temperatures from ambient to 1,200 degrees C. Measurements performed to compare electrical conductivities of state-of-the-art diamond films with those of natural insulating diamond, particularly at temperatures above 700 degrees C.

Vandersande, Jan W.↗

Thermal Conductivity And Expansion Of Graphite/Copper

Report describes fabrication of graphite-fiber/copper-matrix composite plates, measurements of thermal conductivities of plates at temperatures from ambient to 1,073 K, and measurements of thermal expansions of plates from ambient temperature to 1,050 K. Composites promising lightweight, high-thermal-conductivity materials proposed for use in heat exchangers and other heat-transfer components of power systems in spacecraft and hypersonic aircraft. Graphite/copper also of interest as model composite material.

Mcdanels, David L.↗

A new measurement of thermal conductivity of amorphous ice and its implications for the thermal evolution of comets

Very slowly deposited amorphous ice has a thermal conductivity about four orders of magnitude or more smaller than hitherto estimated. Using the exceedingly low value of the thermal conductivity of comets deduced from the properties of amorphous ice leads to the expectation that internal heating of comets is negligible below the outer several tens of centimeters.

Kouchi, Akira↗

Design and Conduct of a Windshear Detection Flight Experiment

A description of the design and conduct of a series of flight experiments which tested the performance of candidate windshear detection devices is presented. With prototype windshear sensors installed, a NASA Boeing 737 test aircraft conducted numerous low altitude penetrations of microburst windshear conditions. These tests were preceded by extensive preparations which included piloted simulations, determination of safe operating limits, and the development of unique flight test hardware, displays, and procedures. The test aircraft and more than 50 research and support personnel were deployed to Orlando, Florida, and Denver, Colorado, during June and July 1991 for field testing. Upon receiving a forecast of developing weather activity, the aircraft crew launched and proceeded to the storm location, guided by uplinked ground radar information and voice communications with ground weather personnel. The tests required constant monitoring of numerous factors including aircraft flight parameters, ground obstructions, windshear magnitude, lightning, escape routes, ATC coordination, storm cell development, and others. The flight tests were extremely successful, safely recording more than 25 low altitude microburst windshear and strong gust front approaches and penetrations, along with completing a full test matrix of additional requirements related to windshear sensor performance. Data quality from the tests was excellent and indicates strong potential for airborne remote sensors to accurately predict and warn the flight crew of hazardous windshear conditions with ample time for precautionary crew action.

Flight Testing↗

Reduced thermal conductivity due to scattering centers in p-type SiGe alloys

Spark erosion was used to produce ultra-fine particles of SiGe thermoelectric material and boron nitride, an inert phonon-scattering material. A homogeneous powder was made by mixing the two powders. The mixture was hot pressed to produce a thermoelectric material with uniformity dispersed, ultra-fine, inert, phonon-scattering centers. It is shown that, in samples with inert boron nitride or silicon nitride, thermal conductivity of a SiGe alloy can be reduced by about 25 percent while maintaining the electrical properties of the samples. Annealing of all the samples at 1525 K caused grain growth to over a micron, eliminating the detrimental effect attributable to small grains. Only in the sample with boron nitride the thermal conductivity did remain well below that for standard p-type SiGe (about 25 percent), while the electrical resistivity and Seebeck coefficient were very close to the values for standard p-type 80/20 SiGe.

Beaty, John S.↗

Remote sensing of vegetation canopy photosynthetic and stomatal conductance efficiencies

The problem of remote sensing the canopy photosynthetic and stomatal conductance efficiencies is investigated with the aid of one- and three-dimensional radiative transfer methods coupled to a semi-empirical mechanistic model of leaf photosynthesis and stomatal conductance. Desertlike vegetation is modeled as clumps of leaves randomly distributed on a bright dry soil with partial ground cover. Normalized difference vegetation index (NDVI), canopy photosynthetic (Ep), and stomatal efficiencies (Es) are calculated for various geometrical, optical, and illumination conditions. The contribution of various radiative fluxes to estimates of Ep is evaluated and the magnitude of errors in bulk canopy formulation of problem parameters are quantified. The nature and sensitivity of the relationship between Ep and Es to NDVI is investigated, and an algorithm is proposed for use in operational remote sensing.

Myneni, R. B.↗

Thermal conductance of gold plated metallic contacts at liquid helium temperatures

The thermal conductance of gold plated OFHC copper, 6061-T6 aluminum, free-machining brass, and 304 stainless steel contacts has been measured over the temperature range of 1.6 to 4.2 K, with applied forces from 22 N to 670 N. The contact surfaces were prepared with a 0.8 micron lapped finish prior to gold coating. It was found that for all materials, except stainless steel, the thermal conductance was significantly improved as the result of gold coating the contact surfaces.

Kittel, Peter↗