SEARCH · Engineering Papers

Results for “blind”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

All sources NASA NTRS DOE OSTI

NASA NTRS1984

Near-optimum design of GaAs-based concentrator space solar cells for 80 C operation

Using a detailed computer simulation model and reasonable values of optical, geometrical and material parameters from current published literature, parameter optimization studies were performed on two cell geometries, namely, the circular geometry for a Cassegrainian concentrator with 100 AM0, 80 C operation and the rectangular geometry for a venetian blind concentrator with 20 AM0, 80 C operation. For each cell geometry, three cell configurations were considered: p/n AlGaAs/GaAs; n/p AlGaAs/GaAs; and, n/p GaAs shallow homojunction. The studies show the possibility of designing GaAs-based space solar cells with beginning-of-life efficiencies exceeding 22 percent at 20 to 100 AM0, 80 C and probable efficiency degradation of less than 15 percent after a 70 percent reduction in diffusion length in each cell region.

Goradia, C.↗

NASA NTRS1985

Operation of a microchannel plate counting system in a mass spectrometer

A multiplier detector system has been developed as part of a mass spectrometer in an ion counting mode. During its operation ions striking a microchannel plate release pulses of electrons which are accelerated to a phosphor layer. The resulting flash of light is carried by a fiber-optic bundle to a photodiode array. The detector simultaneously counts ions throughout a mass spectrum covering more than 30 amu. It extends the mass spectrometer's operation toward low count rates for trace gas analysis. Each mass peak can be independently measured at count rates between 0.1 and 1000 counts/s. Higher rates on a few peaks do not blind the entire detector. The detector's capabilities have been demonstrated by measuring Kr and Xe isotopes in air at natural abundances. The mass spectrometer, detector, and readout electronics are sufficiently compact to permit use in a balloon-borne experiment.

Murphy, D. M.↗

NASA NTRS1985

Evaluation of antimotion sickness drug side effects on performance

The effects of antimotion-sickness drugs on the performance in computerized-pursuit-meter tests of groups of ten 18-30-yr-old male and female subjects are investigated experimentally using double-blind placebo techniques. The results are presented in tables and graphs and discussed in detail. The proficiency scores are as good as or better than placebo values for subjects given d-amphetamine (DA) 5 or 10 mg, promethazine (P) 25 mg + scopolamine (S) 400 ng + DA 10 mg, S 1 mg + DA 10 mg, S 250-600 ng, marezine 50 mg, meclizine 50 mg, dimenhydrinate 50 mg, S 1 mg + DA 5 mg, or P 25 mg + DA 10 mg. Significantly lower scores are seen in subjects given S 800 ng or 1 mg, P 25 mg (oral or IM), P 25 mg + S 400 ng, and P 25 mg oral + P 25 mg IM + DA 10 mg.

Wood, C. D.↗

NASA NTRS1985

Welding, Bonding and Fastening, 1984

A compilation of papers presented in a joint NASA, American Society for Metals, The George Washington University, American Welding Soceity, and Society of Manufacturing Engineers conference on Welding, Bonding, and Fastening at Langley Research Center, Hampton, VA, on October 23 to 25, 1984 is given. Papers were presented on technology developed in current research programs relevant to welding, bonding, and fastening of structural materials required in fabricating structures and mechanical systems used in the aerospace, hydrospace, and automotive industries. Topics covered in the conference included equipment, hardware and materials used when welding, brazing, and soldering, mechanical fastening, explosive welding, use of unique selected joining techniques, adhesives bonding, and nondestructive evaluation. A concept of the factory of the future was presented, followed by advanced welding techniques, automated equipment for welding, welding in a cryogenic atmosphere, blind fastening, stress corrosion resistant fasteners, fastening equipment, explosive welding of different configurations and materials, solid-state bonding, electron beam welding, new adhesives, effects of cryogenics on adhesives, and new techniques and equipment for adhesive bonding.

Buckley, J. D.↗

NASA NTRS1985

Estimating the R-curve from residual strength data

A method is presented for estimating the crack-extension resistance curve (R-curve) from residual-strength (maximum load against original crack length) data for precracked fracture specimens. The method allows additional information to be inferred from simple test results, and that information can be used to estimate the failure loads of more complicated structures of the same material and thickness. The fundamentals of the R-curve concept are reviewed first. Then the analytical basis for the estimation method is presented. The estimation method has been verified in two ways. Data from the literature (involving several materials and different types of specimens) are used to show that the estimated R-curve is in good agreement with the measured R-curve. A recent predictive blind round-robin program offers a more crucial test. When the actual failure loads are disclosed, the predictions are found to be in good agreement.

Orange, T. W.↗

NASA NTRS1986

Thermoluminescence of Antarctic meteorites: A rapid screening technique for terrestrial age estimation, pairing studies and identification of specimens with unusual prefall histories

Thermoluminescence (TL) is a promising technique for rapid screening of the large numbers of Antarctic meteorites, permitting identification of interesting specimens that can then be studied in detail by other, more definite techniques. Specifically, TL permits determination of rough terrestrial age, identification of potential paired groups and location of specimens with unusual pre-fall histories. Meteorites with long terrestrial ages are particularly valuable for studying transport and weathering mechanisms. Pairing studies are possible because TL variations among meteorites are large compared to variations within individual objects, especially for natural TL. Available TL data for several L3 fragments, three of which were paired by other techniques, are presented as an example of the use of TL parameters in pairing studies. Additional TL measurements, specifically a blind test, are recommended to satisfactorily establish the reliability of this pairing property. The TL measurements also identify fragments with unusual pre-fall histories, such an near-Sun orbits.

Sutton, S. R.↗

NASA NTRS1985

Some design guidelines for discrete-time adaptive controllers

There have been many algorithms proposed for adaptive control which will provide globally asymptotically stable controllers if some stringent conditions on the plant are met. The conditions on the plant cannot be met in practice as all plants will contain high frequency unmolded dynamics therefore, blind implementation of the published algorithms can lead to disastrous results. This paper uses a linearization analysis of a non-linear adaptive controller to demonstrate analytically design guidelines which aleviate some of the problems associated with adaptive control in the presence of unmodeled dynamics.

Rohrs, C. E.↗

NASA NTRS1987

Quick-Release Panel Fastener

Quick-release fastener for panels actuated with just one hand. Fastener has no loose parts, does not require mating hardware, and used in blind hole in mating panel. New panel fastener selfcontained unit extending through congruent holes in two panels to be joined. Unit contracts to clamp panels together and expands to release them.

Fosdick, D. R.↗

NASA NTRS1987

Drilling Holes in Graphite/Epoxy

Relatively long-lived bit produces high-quality holes. Effective combination of cutting-tool design, feed, and speed determined for drilling 3/16-and-1/4-in. (0.48-and 0.65-cm) diameter holes in 0.18 in. (0.46cm) thick GM3013A or equivalent graphite/epoxy corrugated spar without backup material and without coolant. Developed to produce holes in blind areas, optimal techniques yielded holes of high quality, with minimal or acceptable delamination and/or fiber extension on drill-exit side.

Minlionica, Ronald↗

NASA NTRS1986

Observation of atmospheric ozone by dial with Raman lasers pumped by a KrF laser

Since the XeCl excimer laser (308 nm) was first used in Differential Absorption Lidar (DIAL) for stratospheric ozone detection, the XeCl ozone lidar became a useful tool for the monitoring of the stratospheric ozone concentration. Shorter wavelength lasers are needed for the observation of ozone in the troposphere where the ozone concentration is about one order of magnitude smaller than in the stratosphere. In 1983, tropospheric ozone was observed with the combination of the second Stokes line (290.4 nm) of stimulated Raman scattering from methane pumped by a KrF laser and the XeCl laser line. The measurement of the ozone distribution from ground to 30 km was reported, using three Stokes lines of Raman lasers pumped by a KrF laser. At wavelengths shorter than 295 nm, the background solar radiation is effectively suppressed by atmospheric ozone. Such a solar-blind effect can be expected when two wavelengths 277 and 290.4 nm are used for DIAL ozone detection. A preliminary measurement of the day time ozone distribution in the troposphere is presented using these wavelengths generated by a KrF laser with a Raman shifter. Analysis using the lidar equation predicts the maximum detectable range is 7 km.

Maeda, M.↗

NASA NTRS1986

Two-photon laser-induced fluorescence detection of OH

The TP-LIF OH sensor is based on the principle that a molecule having multiple energy states, all of which are bonding, can be pumped into the highest state with the resulting fluorescence being blue-shifted relative to all pumping wavelengths. In this way, one can successfully discriminate against virtually all noise sources in the system using long wavelength blocking filters in conjunction with solar-blind photomultiplier tubes. Thus, these systems tend to be signal limited rather than signal-to-noise limited as is true of the SP-LIF technique as well as other conventional analytical methods. The trick to achieving the above sampling scheme, with high efficiency, is in the use of high photon fluxes of short time duration. Obviously, the latter type of light source is fulfilled nicely by available pulsed lasers. From an operational point of view, however, this laser source needs to be tunable. The latter characteristic permits extremely high selectivity for the detection of a diatomic or simple polyatomic molecule by taking advantage of the high-resolution spectroscopic features of these type species.

Davis, D. D.↗

NASA NTRS1986

Detection of CN emission in Comet P/Halley

The first detection of the CN 3883 A band in emission in Comet P/Halley (1982) in February 1985 is reported. The detection technique, which is described, used blind offsets from secondary reference stars to the comet's predicted position, and involved plotting the comet's track on an enlargement of an appropriate section of the Palomar Sky Survey E plates. The strong solar continuum in the resulting cometary spectrum demonstrates the dominance of the dust reflection spectrum and the reflection from the nucleus. The 3883 A feature is identified with the v = 0 band sequence of the blue system of CN; no other significant features were identified in the spectrum.

Wyckoff, S.↗

NASA NTRS1986

Joining technologies for the 1990s: Welding, brazing, soldering, mechanical, explosive, solid-state, adhesive

A compilation of papers presented in a joint NASA, American Society for Metals, The George Washington University, American Welding Society, and Society of Manufacturing Engineers Conference on Welding, Bonding, and Fastening at Langley Research Center, Hampton, VA, on October 23 to 25, 1984 is given. Papers were presented on technology developed in current research programs relevant to welding, bonding, and fastening of structural materials required in fabricating structures and mechanical systems used in the aerospace, hydrospace, and automotive industries. Topics covered in the conference included equipment, hardware and materials used when welding, brazing, and soldering, mechanical fastening, explosive welding, use of unique selected joining techniques, adhesives bonding, and nondestructive evaluation. A concept of the factory of the future was presented, followed by advanced welding techniques, automated equipment for welding, welding in a cryogenic atmosphere, blind fastening, stress corrosion resistant fasteners, fastening equipment, explosive welding of different configurations and materials, solid-state bonding, electron beam welding, new adhesives, effects of cryogenics on adhesives, and new techniques and equipment for adhesive bonding.

Buckley, John D.↗

NASA NTRS1988

Acoustical Measurement Of Mine-Shaft Length

Acoustical system proposed to measure depth of a "blind" shaft. Acoustic wave guided by shaft and provides estimate of shaft length, from which volume estimated. Acoustic-generator system determines resonant-frequency difference to measure shaft length.

Heyman, Joseph S.↗

NASA NTRS1988

Dowel Remover

Special tool pulls dowel pins straight out of blind holes. Removes dowels without damaging them or possibly injuring user. Accepts most common dowel sizes, 1/8 to 5/8 inch. Tool is simple and inexpensive. Made from screw, threader bar, slotted pipe, and nut.

Blisse, Jerry↗

NASA NTRS1988

Programmable Grit-Blasting System

In programmable grit-blasting system undergoing design, controller moves blasting head to precise positions to shape or remove welding defects from parts. Controller holds head in position for preset dwell time and moves head to new position along predetermined path. Position of articulated head established by pair of servomotors according to programmed signals from controller. Head similar to video borescope. Used to remove welding defects in blind holes. Suited for repetitive production operations in grit-blast box.

Burley, Richard K.↗

NASA NTRS1987

Short range forecasting of sea breeze generated thunderstorms at the Kennedy Space Center: A real-time experiment using a primitive equation mesoscale numerical model

The operational efficiency of using guidance from a mesoscale numerical model to improve sea breeze thunderstorm forecasts at and around the Shuttle landing strip was assessed. The Prognostic Three-Dimensional Mesoscale (P3DM) model, developed as a sea breeze model, reveals a strong correlation between regions of mesoscale convergence and the triggering of sea breeze convection thunderstorms. The P3DM was modified to generate stability parameters familiar to the operational forecaster. In addition to the mesoscale fields of wind, vertical motion, moisture, temperature, a stability indicator, a combination of model-predicted K and Lifted Indices and the maximum grid cell vertical motion, were proposed and tested. Results of blind tests indicate that a forecaster, provided with guidance derived from model output, could improve local thunderstorm forecasts.

Lyons, Walter A.↗

NASA NTRS1988

DSS 14 antenna calibrations for GSSR/VLA Saturn radar experiments

The DSS 14 pointing and gain were calibrated to support X-band bistatic radar observations of Saturn's rings. The observations used the Goldstone Solar System Radar and the National Radio Astronomy Observatory's Very Large Array (VLA) in Socorro, New Mexico. The pointing calibrations were based on conscan offset data collected during Voyager 1 and 2 support passes. The conscan data show angle-of-arrival sensing with no bias and 0.3 mdeg 1-sigma error. Using the calibrations, demonstrated blind pointing performance on Saturn was less than 3 mdeg 1-sigma error. Meteorological observations at the site were used to reduce elevation errors caused by atmospheric refraction. The techniques used corrected about one-third of the error-poorer than expected performance.

Guiar, C. N.↗