SEARCH · Engineering Papers

Results for “blade”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Data for "Constitutive Down-Regulation of Liguleless Alleles in Sorghum Drives Increased Productivity and Water Use Efficiency"

Plant architecture influences the microenvironment throughout the canopy layer. Plants with a more erect leaf architecture allow for an increase in planting densities and allow more light to reach lower canopy leaves. This is predicted to increase crop carbon assimilation. Frictional resistance to wind reduces air movement in the lower canopy, resulting in higher humidity. By increasing the proportion of canopy photosynthesis in the more humid lower canopy, gains in the efficiency of water use might be expected, although this may be slightly offset by the more open erectophile form canopy. An anatomical feature in members of the Poaceae family that impacts leaf angle is the articulated junction of the sheath and blade, which also bares the ligule and auricles. Mutants, which lack ligules and auricles, show no articulation at this junction, resulting in leaves that are near vertical. In maize, these phenotypes termed liguleless result from null mutations of genes: ZmLG1 (Zm00001eb67740) and ZmLG2 (Zm00001eb147220). In sorghum, SbiRTx430.06G264300 (SbLG1) and SbiRTx430.03G392300 (SbLG2) are annotated as the respective maize homologues. A hair-pin element designed to down-regulate both SbLG1 and SbLG2 was introduced into the grain sorghum genotype RTx430. Derived transgenic events harbouring the hair-pin failed to develop ligules and displayed reduced leaf angles to the vertical, but less vertical than in null mutations. Under field settings, plots sown with these sorghum events having an erect architecture phenotype displayed an increase in photosynthesis in lower canopy levels, which led to increases in above-ground biomass and seed yield, without an increase in water use.

Genome Engineering↗

DOE OSTI2025

Laser-driven high-resolution MeV x-ray tomography

The need for high-resolution MeV x-ray tomography to observe the three-dimensional structure of dense, large-sized objects is rapidly increasing for the non-destructive evaluation of critical additively manufactured parts, national security, and other applications. We report a demonstration of high-resolution MeV computed tomography of a dense, large object with a laser-driven x-ray source. A record detector-limited MeV radiograph resolution of < 200 µm as determined with the Bennett approximation of the point spread function was achieved by irradiating millimeter-thick tungsten targets with 300 TW femtosecond laser pulses at a 0.5 Hz repetition rate. A tungsten alloy step wedge spectrometer indicates that the peak of the x-ray emission is between 1 and 2 MeV, with an endpoint energy of 19 MeV. To illustrate the radiographic imaging capability of the system, a tomographic reconstruction of a nickel superalloy turbine blade ( maximum $ρr$ = 139 g/cm 2 ) with sub-millimeter resolution was performed using 2160 individual radiographs. The small x-ray source size opens the prospect of extremely high-resolution tomographs of large, dense objects. This laser-driven approach has major advantages for non-destructive evaluation.

47 OTHER INSTRUMENTATION↗

DOE OSTI2025

Ultrasonic deterrents provide no additional benefit over curtailment in reducing bat fatalities at an Ohio wind energy facility

Wind energy is important for achieving net-zero greenhouse gas emissions but also contributes to global bat mortality. Current strategies to minimize bat mortality due to collision with wind-turbine blades fall broadly into two categories: curtailment (limiting turbine operation during high-risk periods) and deterrence (discouraging bat activity near turbines). Recently, there has been interest in combining these strategies to achieve greater reductions in bat fatalities than either strategy might achieve in isolation. To investigate the effectiveness of combining curtailment with ultrasonic deterrent minimization strategies, we deployed six ultrasonic deterrents at nacelle height on 16 experimental turbines at Avangrid Renewables’ Blue Creek Wind Energy Facility. We rotated between four conditions (normal operations, curtailment only, deterrent only, curtailment and deterrent) randomly assigned to four wind turbines each night between 15 June and 3 October 2017. We found that bat mortality at wind turbines was independent of wind speed. The effectiveness of ultrasonic acoustic deterrents varied between high-frequency-calling species (eastern red bats) and low-frequency-calling species (hoary bats, silver-haired bats, and big brown bats). When deterrents were active, mortality was twice as high for eastern red bats compared to the control. Conversely, deterrents had a weak dampening effect on bat mortality for low-frequency species. We found no additive effects on mortality reduction for turbines operating both curtailment and deterrents compared to either approach in isolation. Our findings suggest that ultrasonic acoustic deterrents may not be effective for both high and low frequency echolocating bats. The increase in fatalities of eastern red bats is alarming and underscores the importance of considering site- and species-specific effects of minimization solutions.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

Seaborgite, LiNa6K2(UO2)(SO4)5(SO3OH)(H2O), the First Uranyl Mineral Containing Lithium

Abstract Seaborgite (IMA2019-087), LiNa6K2(UO2)(SO4)5(SO3OH)(H2O), is a new mineral species from the Blue Lizard mine, Red Canyon, San Juan County, Utah, U.S.A. It is a secondary phase found on gypsum in association with copiapite, ferrinatrite, ivsite, metavoltine, and römerite. Seaborgite occurs in sprays of light-yellow, long flattened prisms or blades, up to about 0.2 mm in length. Crystals are elongated on [100], flattened on {010}, and exhibit the forms {100}, {010}, {001}, and {101}. The mineral is transparent with vitreous luster and very pale-yellow streak. It exhibits bright lime-green fluorescence under a 405 nm laser. The Mohs hardness is ~2½. The mineral has brittle tenacity, curved or conchoidal fracture, and one good cleavage on {100}. The measured density is 2.97(2) g/cm3. The mineral is immediately soluble in H2O at room temperature. The mineral is optically biaxial (–), α = 1.505(2), β = 1.522(2), γ = 1.536(2) (white light); 2Vmeas = 85(1)°; moderate r < ν dispersion; orientation X ^ a ≈ 10°; pleochroic X colorless, Y and Z light green-yellow; X < Y ≈ Z. EPMA and LA-ICP-MS analyses of seaborgite undermeasured its Li, K, and Na. The empirical formula using Li, Na, and K based on the structure refinement is Li1.00Na5.81K2.19(UO2)(SO4)5(SO3OH)(H2O). Seaborgite is triclinic, P1, a = 5.4511(4), b = 14.4870(12), c = 15.8735(15) Å, α = 76.295(5), β = 81.439(6), γ = 85.511(6)°, V = 1203.07(18) Å3, and Z = 2. The structure (R1 = 0.0377 for 1935 I = 2σI) contains [(UO2)2(SO4)8]4– uranyl-sulfate clusters that are linked into a band by bridging LiO4 tetrahedra. The bands are linked through peripheral SO4 tetrahedra forming a thick heteropolyhedral layer. Channels within the layers contain a K site, while an additional K site, six Na sites, and an SO3OH group occupy the space between the heteropolyhedral layers.

Geochemistry & Geophysics↗

DOE OSTI2023

Finchite, Sr(UO 2 ) 2 (V 2 O 8 )·5H 2 O, a new uranyl sorovanadate with the francevillite anion topology

Finchite (IMA2017-052), Sr(UO 2 ) 2 (V 2 O 8 )·5H 2 O, is the first uranium mineral known to contain essential Sr. The new mineral occurs as yellow-green blades up to ~10 µm in length in surface outcrops of the calcrete-type uranium deposit at Sulfur Springs Draw, Martin County, Texas, U.S.A. Crystals of finchite were subsequently discovered underground in the Pandora mine, La Sal, San Juan County, Utah, U.S.A., as diamond-shaped golden-yellow crystals reaching up to 1 mm. In this work, the crystal structure of finchite from both localities was determined using single-crystal X-ray diffraction and is orthorhombic, Pcan, with a = 10.363(6) Å, b = 8.498(5) Å, c = 16.250(9) Å, V = 1431.0(13) Å 3 , Z = 4 (R 1 = 0.0555) from Sulfur Springs Draw; and a = 10.3898(16), b = 8.5326(14), c = 16.3765(3) Å, V = 1451.8(4) Å 3 , Z = 4 (R 1 = 0.0600) from the Pandora mine. Electron-probe microanalysis provided the empirical formula (Sr 0.88 K 0.17 Ca 0.10 Mg 0.07 Al 0.03 Fe 0.02 ) Σ1.20 (UO 2 ) 2 (V 2.08 O 8 )·5H 2 O for crystals from Sulfur Springs Draw, and (Sr 0.50 Ca 0.28 Ba 0.22 K 0.05 ) Σ0.94 (U 0.99 O 2 ) 2 (V 2.01 O 8 )·5H 2 O for crystals from the Pandora mine, based on 17 O atoms per formula unit. The structure of finchite contains uranyl vanadate sheets based upon the francevillite topology. Finchite is a possible immobilization species for both uranium and the dangerous radionuclide 90 Sr because of the relative insolubility of uranyl vanadate minerals in water.

58 GEOSCIENCES↗

DOE OSTI2019

Developing Efficient Perovskite/Silicon Tandem Devices

This project aims at developing highly efficient perovskite/silicon tandem solar cells by developing efficient perovskite top cells, silicon bottom cells, and monolithically integrating the subcells for highly efficient tandem solar cells. The project focused on increasing the efficiency of perovskite solar cells to 20% and understanding related materials science and device physics, as well as developing a compatible bottom high-efficiency c-Si solar cell. The perovskite cells with a wide bandgap of 1.61 eV and 1.84 eV are fabricated by a low-cost, low-temperature, scalable solution process on lower bandgap silicon bottom cells. The bandgaps of perovskite top cells have been tuned between 1.61 eV and 1.84 eV by composition engineering mainly through controlling the halide mixing ratio in perovskite materials. The efficiencies of the wide bandgap perovskite solar cells have been improved to an excellent efficiency of 21.0% for perovskites with a bandgap of 1.63 eV with increased grain size, reduced energy disorder at cathode contact, and defect passivation. We invented a solvent annealing approach with solvent vapor during thermal annealing to enlarge grain size of perovskite film which reduces the charge trap density and improves the device efficiency. Moreover, we discovered that the non-wetting surface could further increase the grain size for perovskite films, because non-wetting surface could prevent the formation of too dense nuclei from heterogeneous nucleation process. We proposed to reduce the energy disorder of organic charge extraction layer to reduce the power loss in perovskite cells. We pioneered defect passivation concept and techniques to suppress the charge non-radiative recombination in perovskite solar cells to boost the efficiency. For the silicon bottom cell development, different from the conventional silicon cell work under full illumination, the light available for the silicon bottom cell in tandem structure is mainly NIR region. We developed a NIR enhanced silicon cell with efficiency of 21.2% by applying a double-layer antireflection coating at the front side and a MgF2 back reflector layer at the rear side. For the perovskite/silicon tandem device, we achieved a highest reported power conversion efficiency of 25.4% in 2018, and further increased the efficiency up to 26.0% in 2019. The research on tandem solar cells focused on reducing reflection loss to <5% at spectrum of 300-1100 nm by antireflection layer, tuning the bandgap of perovskite film for matched current density between sub-cells, and utilizing a ITO layer between perovskite top cell and silicon bottom cell as interconnect layer without Voc loss. Finally, we developed a blading technique to fabricate perovskite films which produces perovskite solar cells with comparable or even superior efficiency to those made by non-scalable spin coating method. This paves the way for scaling up perovskite/silicon tandem solar cells using solution approach.

14 SOLAR ENERGY↗

DOE OSTI2020

Compare linear-system solver and preconditioner stacks with emphasis on GPU performance and propose phase-2 NGP solver development pathway

The goal of the ExaWind project is to enable predictive simulations of wind farms comprised of many megawatt-scale turbines situated in complex terrain. Predictive simulations will require computational fluid dynamics (CFD) simulations for which the mesh resolves the geometry of the turbines and captures the rotation and large deflections of blades. Whereas such simulations for a single turbine are arguably petascale class, multi-turbine wind farm simulations will require exascale-class resources. The primary physics codes in the ExaWind project are Nalu-Wind, which is an unstructured-grid solver for the acoustically incompressible Navier-Stokes equations, and OpenFAST, which is a whole-turbine simulation code. The Nalu-Wind model consists of the mass-continuity Poisson-type equation for pressure and a momentum equation for the velocity. For such modeling approaches, simulation times are dominated by linear-system setup and solution for the continuity and momentum systems. For the ExaWind challenge problem, the moving meshes greatly affect overall solver costs as reinitialization of matrices and recomputation of preconditioners is required at every time step. In this report we evaluated GPU-performance baselines for the linear solvers in the Trilinos and hypre solver stacks using two representative Nalu-Wind simulations: an atmospheric boundary layer precursor simulation on a structured mesh, and a fixed-wing simulation using unstructured overset meshes. Both strong-scaling and weak-scaling experiments were conducted on the OLCF supercomputer Summit and similar proxy clusters. We focused on the performance of multi-threaded Gauss-Seidel and two-stage Gauss-Seidel that are extensions of classical Gauss-Seidel; of one-reduce GMRES, a communication-reducing variant of the Krylov GMRES; and algebraic multigrid methods that incorporate the afore-mentioned methods. The team has established that AMG methods are capable of solving linear systems arising from the fixed-wing overset meshes on CPU, a critical intermediate result for ExaWind FY20 Q3 and Q4 milestones. For the fixed-wing strong-scaling study (model with 3M grid-points), the team identified that Nalu-Wind simulations with the new Trilinos and hypre solvers scale to modest GPU counts, maintaining above 70% efficiency up to 6 GPUs. However, there still remain significant bottlenecks to performance: matrix assembly (hypre), AMG setup (hypre and Trilinos) In the weak-scaling experiments (going from 0.4M to 211M gridpoints), it's shown that the solver apply phases are faster on GPUs, but that Nalu-Wind simulation times grow, primarily due to the multigrid-setup process. Finally, based on the report outcomes, we propose a linear solver path-forward for the remainder of the ExaWind project. Near term, the NREL team will continue their work on GPU-based linear-system assembly. They will also investigate how the use of alternatives to the NVIDIA UVM (unified virtual memory) paradigm affects performance. Longer term, the NREL team will evaluate algorithmic performance on other types of accelerators and merge their improvements back to the main hypre repository branch. Near term, the Trilinos team will address performance bottlenecks identified in this milestone, such as implementing a GPU-based segregated momentum solve and reusing matrix graphs across linear-system assembly phases. Longer term, the Trilinos team will do detailed analysis and optimization of multigrid setup.

17 WIND ENERGY↗

DOE OSTI2020

Evaluation of Steam Cycle Upgrades to Improve the Competitiveness of U.S. Coal Power Plants (Final Scientific / Technical Report)

Increasing the competitiveness of the existing pulverized-coal utility fleet in the United States may be achieved by decreasing heat rate, via increases in steam cycle efficiency through upgraded steam temperatures and use of latest technology available in steam turbine and blading design. The average net plant efficiency of the US coal-fired fleet is approximately 33% (HHV). Plant efficiency increases to approximately 41.4% (HHV) at 1,350°F (732°C) steam temperature. However, achieving these Advanced Ultra-Super Critical (AUSC) steam conditions requires the use of advanced high-temperature materials. While there has been a significant amount of DOE-funded materials R&D, most of the related design work has focused on new (greenfield) units, rather than on opportunities to retrofit this advanced technology to the existing utility fleet. If technology, based upon the advanced materials required for AUSC steam conditions, may be applied to the existing fleet, using an economically viable retrofit, a higher capacity factor can be expected as a result of the increased plant competitiveness. The Electric Power Research Institute (EPRI) was awarded a project by the US Department of Energy to examine the technical and economic feasibility of a series of steam cycle upgrades to the two most prevalent types of U.S. coal power plants: 2,400 psig (16.6 MPa) subcritical and 3,500 psig (24.1 MPa) supercritical pulverized coal units. The nine upgrade options that were originally being considered included increasing the main and reheat steam temperatures from 1,000°F (538°C) to 1,100°, 1,200°, and 1,350°F (593°C, 649°C, and 732°C) while holding the steam pressures constant at their original design values, and cases where just the main steam or reheat steam temperatures were increased. The objective was to minimize the modifications required to the existing power plant while still providing a significant improvement in heat rate. The upgrade options assumed that the boiler enclosure envelope remained unchanged from each base case, and that all applicable OEM design guidelines for normal commercial units were imposed. For the highest temperature supercritical case, an option of using a low-pressure molten salt loop to transfer heat from the furnace to the steam was examined. The first major task of the work scope was designed to examine the technical feasibility of various upgrade options, while the subsequent work determined economic viability of the technically feasible upgrade options. Prior to evaluating the effect of these increased temperatures, a “base case” model of a subcritical and supercritical PC boiler was created, which was used for comparative purposes. Upgrade options were evaluated at full-load, part-load and dynamic transient conditions. Once the technical feasibility of each upgrade option was evaluated, the economic value of the heat rate improvement of each feasible option was determined by detailed modeling of unit dispatch in several regional power markets. The dispatch model was used to estimate the amount of revenue from power sales the upgraded unit would receive in comparison to a non-upgraded version of the same power plant. As a parallel task to the dispatch analysis, the capital cost of implementing the upgrades was estimated. The capital cost estimates were then compared to the increased revenue estimated by the dispatch modeling to determine the economic attractiveness of each upgrade option. Several upgrade options were determined to be technically feasible. The net present value (NPV) of the costs for steam cycle upgrades considered in this study ranged from approximately $\$$111 to $\$$130 million. The economic modeling results show that the unit dispatch changes resulting from steam cycle upgrades are relatively small, due largely to heat rate (and operating cost) changes being relatively small. Additionally, the cost of each upgrade exceeds the net revenue increases associated with the upgrade case. Note that the breakeven values are higher for subcritical retrofits, but the capital costs for the subcritical upgrades are also slightly higher. In typical new pulverized coal plants, fuel accounts for approximately 25% of the cost of electricity (COE), while capital costs represent around 50% of the COE. Therefore, in order to improve the heat rate by 4% one can only afford to increase the capital cost by 2%, at the same cost of electricity. The conclusion of this study is that without a cost for emitting CO 2 , it will be difficult to pay for significant efficiency improvements on plants firing low cost coals.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2020

2020 State of the Science Report, Chapter 10: Environmental Monitoring Technologies and Techniques for Detecting Interactions of Marine Animals with Turbines

The greatest potential risk from turbine operation continues to be perceived by regulators and other stakeholders to be that of marine animals colliding with turbine blades. These potential interactions are the most difficult to observe using common oceanographic instruments and must be undertaken in parts of the ocean where fast moving water and high waves make studies challenging. However, our collective understanding of the effects of marine renewable energy (MRE) devices on marine animals and their habitats has improved since the publication of the 2016 State of the Science report. https://tethys.pnnl.gov/publications/state-of-the-science-2020-chapter-10-environmental-monitoring

16 TIDAL AND WAVE POWER↗

DOE OSTI2020

Best Practices for Shielding Analyses of Activated Metals and Spent Resins from Reactor Operation

This report investigated best practices for performing shielding evaluations of Type B waste packages, as defined in 10 CFR Part 71 regulations on packaging and transportation of radioactive material, or packages for which the contents are not defined before loading and may include a broad range of nuclides, geometries, and non-fuel materials. The following non-fuel waste streams were analyzed: Activated metals from decommissioned commercial power reactors, including Type 304 stainless steel, reactor vessel steel, and Inconel, Control blades from boiling water reactors, Neutron-activated corrosion products on surfaces of activated metals, and Spent resins from power plant operations. Measured elemental compositions, including major constituents and impurities, for steel and Inconel samples from commercial power reactors were used in activation calculations to determine radionuclide inventories in activated metals. For a simplified cask model, 60 Co contribution to the total external package dose rate at 30 days after shutdown varied from approximately 60% to 95%, depending on the activated metal, initial cobalt impurity concentration in the metal, and the thickness of the overpack gamma shield. Its maximum contribution to the total external package dose rate of approximately 100% was reached within the time interval of 2 to 5 years after shutdown and was maintained for up to 45 to 60 years after shutdown, depending on material, initial cobalt impurity concentration, and shield thickness. Thereafter, the 60 Co contribution to external package dose rate decreased with increasing decay time. Cobalt-60 is primarily produced by neutron reactions with the cobalt impurity in steel and Inconel. Other important radionuclides in activated metals contributing to package external dose rate are radionuclides with relatively short decay times, including 51 Cr, 59 Fe, 58 Co, and 54 Mn. These radionuclides may be represented as an equivalent 60 Co activity/source because 60 Co gamma ray emissions are bounding in terms of source strength and energy to other important radionuclides identified in the analyzed activated metals. Approaches for modeling the neutron-activated corrosion products that may be attached to activated reactor components were analyzed in this report. It was demonstrated that a surface source is more conservative than a uniform volumetric source for the treatment of neutron-activated corrosion products with respect to external package dose rates. An analysis of the maximum radionuclide loadings reported on spent resins identified the radionuclides 137 Cs, 60 Co, 134 Cs, 65 Zn, and 58 Co as the primary contributors to external package dose rate. For a resin cooled for 3.08 years, the external package dose rate was entirely produced by the reported 137 Cs and 60 Co inventory. The neutron sources from actinides found on spent resins or activated metals produced negligible dose rates and may be ignored in dose rate analyses. Effects of idealized waste material, source geometry, and spatial material/source distributions on external package dose rates were determined based on dose rate results for a simplified cask model under normal conditions of transport. Type 304 stainless steel, zirconium, and aluminum with adjusted mass densities based on a maximum content weight were analyzed for material modeling effects on external package dose rate. These materials produced identical external package dose rates within the statistical uncertainties of the dose rate estimates. Among four different source geometry configurations with homogeneous material of different mass densities, uniform volumetric source distribution, and the same source strength, the geometry configuration with lowest mass density (i.e., minimum self-shielding effect among the four cases) was most conservative. Spatial source distributions that better represent localized peak 60 Co activity values were more conservative than a uniform volumetric source distribution, assuming the same weight and total source strength per package. The increase in external dose rate caused by localized source peaks can be as much as the ratio between source peak activity density to average activity density, depending on the location of the activated metal with peak activity density. Therefore, the shielding analysis may be simplified if localized peak activities and the average activity per package can be measured/determined and documented at the time of cask loading. For simplicity, external package dose rates may be determined based on average source activity and a uniform volumetric source distribution. The dose rate results from that calculation model multiplied by the ratio of peak activity density to average activity density will produce maximum dose rate values for conservative estimates.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Demonstration and performance testing of extreme-resolution simulations with static meshes on Summit (CPU & GPU) for a parked-turbine configuration and an actuator-line (mid-fidelity model) wind farm configuration (ECP-Q4 FY2020 Milestone Report)

17 WIND ENERGY↗

DOE OSTI2021

HFIR SiC Bowing Test Ready to Insert

This report describes the successful assembly of a High Flux Isotope Reactor (HFIR) irradiation experiment designed to assess radiation-induced lateral bowing of silicon carbide fiber–reinforced, silicon carbide matrix composite (SiC/SiC) components under a radial fast neutron flux gradient. Excessive bowing of a SiC/SiC channel box in a boiling water reactor could potentially interfere with control blade movements. Similar concerns exist for SiC/SiC fuel cladding in light water reactors. The experiment described herein will provide experimental validation of the structural response of a miniature SiC/SiC channel box and tube specimens with pressurized water reactor diameters during irradiation. The significant radial fast neutron flux gradients that exist in the permanent reflector of HFIR were characterized using detailed three-dimensional neutronic calculations. The three-dimensional displacement damage dose rate profile and the resulting volumetric swelling in SiC were used as inputs to structural analyses that predicted the deformation and stresses in the channel box specimen. The specimens were thoroughly characterized prior to irradiation using traditional dimensional inspection and surface profilometry so that these measurements can later be compared with similar measurements that will be made post-irradiation to determine radiation-induced deformations. Furthermore, fine engraving markers were inscribed along all outer surfaces of the specimen and mapped using a digital microscope and a three-dimensional stage. This technique allowed for accurate measurements of the marker spacings, which can be compared with similar measurements that will be made post-irradiation to provide local radiation-induced strain mapping. The experiment was successfully assembled and is scheduled for insertion during HFIR cycle 492, which is currently scheduled to run from May 25, 2021 to June 18, 2021.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Conventional Rib Turbulators For SCO 2 Turbine Internal Cooling (Report)

This report documents experimental work in the NETL Heat Exchange and Experimental Testing (HEET) rig. The heat transfer performance of additively manufactured internal cooling features in supercritical CO 2 were characterized. It was demonstrated that the thermal performance factor of conventional angled rib turbulators remains independent of Reynolds number up to 3.1 x 10 5 indicating that these features may be employed to enhance heat transfer in sCO 2 turbine blades and vanes. This augmentation of heat transfer in the internal cooling passages decreases the required turbine coolant and improves the power cycle efficiency.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2021

Film Cooling Performance Predictions For Air And Supercritical CO 2

The current study explores the possibility of cooling the vanes and blades of a direct-fired sCO 2 turbine using film cooling geometries. The operating conditions of a direct-fired sCO 2 cycle and thermophysical properties of the fluid at those conditions can alter the flow field characteristics of the coolant jet and its mixing with the mainstream. Very little information is present in the literature regarding the performance of film cooling geometries employing a supercritical fluid. The objective of this study is to estimate the resulting film cooling effectiveness while also capturing the effects of the crossflow-to-mainstream velocity ratio on the coolant jet. A computational fluid dynamic model is used to study the coolant jet exiting a cylindrical hole located on a flat plate, with the coolant fed by an internal channel. Steady-state RANS equations were solved along with the SST kω model to provide the turbulence closure. The operating conditions for the direct-fired sCO 2 turbine are obtained using an in-house Cooled Turbine Model. Numerical predictions revealed that the crossflow effects and jet lift-off were more pronounced in the case of sCO 2 when compared to air. Spatial distribution of flow field and cooling effectiveness will be presented at different operating conditions. Recommendations for future studies will be given wherever applicable.

42 ENGINEERING↗

DOE OSTI2021

AOI [1]: Passive Wireless Sensor Systems Fabricated by Direct-Writing for Temperature and Health Monitoring of Energy Systems in Harsh-Environments (Final Report)

Researchers at West Virginia University (WVU) propose to demonstrate a wireless, high-temperature sensor system for monitoring the temperature and health of energy-system components. The active sensor and electronics for wireless communication will be composed entirely of an electroceramic materials (conductive ceramics) which are capable of withstanding the harsh-environments required for fossil energy-based technologies. This work will focus primarily on the fabrication and testing of temperature (thermocouples and thermistors) and health (strain/stress and crack propagation sensors) that function at extreme temperatures (up to 700-1700ºC). The electronics will accompany the high-temperature sensor, which will include a passive wireless communication circuit that allows the transmission of the data based on the LCR resonance principle to a near-by reader antenna. This passive transmission of data will reduce the need for interconnect wires near the active, and possibly rotating, energy-system component. The research will include process development to permit the 2D/3D direct-writing of the entire sensor and communication circuit onto the energy-system component. The direct-writing will be facilitated by using silicon-based polymer-derived precursors to form the high-temperature, stable electroceramic compositions. In addition, methods for direct-writing the circuit onto a fugitive carrier substrate will be completed, which will permit a “peel-and-stick”-like transfer of the sensor circuit to the energy-system component. This feature will allow the economical and precise placement of the sensor circuit onto components of various shapes and locations, without altering the geometry and active features of the manufactured component, or the removal (or decommissioning) of the component for installation. The proposed work will be directed at the following areas: 1) Investigation of phase formation, sintering/grain growth, and electrical properties of polymer-derived electroceramic composites; 2) Definition of processes to direct-write through ink-jet and robo-casting the polymer-derived electroceramic composites onto oxide and polymer surfaces; 3) Development of methods to form monolithic "peel-and-stick" preforms that will efficiently transfer the sensor circuit to ceramic surfaces after thermal treatment; 4) Design of passive wireless LCR circuits and receiver (reader) antennas for communication and testing at high temperatures; 5) Investigation of the passive wireless sensor system developed (and method of transferring sensor system) for temperature and stress/strain measurements on a SOFC repeat unit and a singular gas turbine blade prototype as example applications.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Biological Response Models: Predicting Injury and Mortality of Fish During Downstream Passage through Hydropower Facilities

This report describes the U.S. Department of Energy’s HydroPASSAGE project efforts to develop and collect biological response models for integration into the Biological Performance Assessment (BioPA) toolset and the Hydropower Biological Evaluation Toolset (HBET). These models help understand how fish are likely to respond during dam passage when exposed to hydraulic and physical stressors associated with turbines and other hydropower structures. When fish pass through hydropower facilities, they may encounter several stressors, of which the three most common are collision, rapid decompression, and fluid shear. Specialized equipment has been used to develop 99 biological response models for exposure to blade strike, rapid decompression, or fluid shear. The models were gathered from the literature or developed as part of this effort and include models for 31 different species of fish that have various predicted endpoints (i.e., injury or mortality). Among these models, considerable variation in susceptibility to the stressors has been observed from one species to another, and a species’ susceptibility to one stressor does not necessarily indicate similar susceptibility to another. Although several species have been examined, it is still unclear how many other species, which may have different morphological traits, may respond to these stressors, so further examination of the different species is needed. These models can and have been applied in several different cases, often using the BioPA toolset and HBET, to better understand the potential for injury and mortality that may occur during fish passage at hydropower facilities, including specific applications, such as turbine replacement, the installation of new turbines, or changing operations of currently installed turbines. As hydropower is continually developed to meet the electricity needs of society, tools such as HBET and BioPA, used with the integrated biological response models, will aid in the development of technologies and strategies that avoid, minimize, mitigate, or manage environmental effects.

13 HYDRO ENERGY↗

DOE OSTI2022

Develop Direct 3D Building as a Transformational 3D Printing

Phase 1 of this project recognizes the key advantages of direct 3D building (3DB) by literature research, initial experiments, and analyses. The fundamental enhancement in powder density, layer thickness, and their uniformities are attributed to the independence from high blade speed and powder flowability. The increase in layer quality, before selective fusion, is found qualitatively significant for a step change in process robustness when the unrepeatability of 3D printing (3DP) remains a challenge in serial volume production. The reduced challenge of powder flowability should not only entail improvement in build quality but also reduce powder cost from the strict morphology and size specs. The concurrent selective fusion and powder surface preparation eliminate the need for frequent recoating pauses to increase build speed. On-going experiments include density cup measurements by X-ray scanning and recoating performance evaluation by a rotating disk system to verify some of the results.

42 ENGINEERING↗

DOE OSTI2021

HFIR SiC-SiC Composite Clad Tube Bowing Test: Pre-Irradiation Characterization

This report describes the pre-irradiation characterization of the SiC-SiC composite clad tube bowing experiment that will be irradiated in the High Flux Isotope Reactor (HFIR). There are concerns that SiCSiC fuel cladding in light water reactors could undergo bowing because of the non-uniform fast neutron flux profiles. This experiment is combined with the SiC-SiC channel box experiment, which has similar concerns regarding control blade movements in boiling water reactors. The HFIR experiment aims to validate the predicted deformation and stresses in the composite clad specimen after the exposure of fast neutron flux gradients. Significant radial fast neutron flux gradients that exist in the permanent reflector of HFIR were thoroughly characterized by using detailed 3D neutronic calculations. The 3D displacement damage dose rate profile and the resulting volumetric swelling in SiC were used as inputs to structural analyses to determine the predicted deformation that will affect the specimens. The tube specimens were characterized by using traditional dimensional inspection and surface profilometry to provide detailed information regarding the pre-irradiation condition as the first step to evaluate the radiation-induced deformation. Furthermore, fine engraving markers were inscribed along all outer surfaces of the specimen and mapped by using a digital microscope and a multidimensional stage. This allows marker spacings to be accurately measured and compared with similar measurements that will be made post-irradiation to provide local radiation-induced strain mapping. The experiment successfully completed two HFIR cycle irradiations, cycles 492 and 493, which finished on July 25, 2021.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗