SEARCH · Engineering Papers

Results for “ambient temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Static performance tests of a flight-type STOVL ejector

The design and development of thrust augmenting STOVL ejectors has typically been based on experimental iteration (i.e., trial and error). Static performance tests of a full scale vertical lift ejector were performed at primary flow temperatures up to 1560 R (1100 F). Flow visualization (smoke generators and yarn tufts) were used to view the inlet air flow, especially around the primary nozzle and end plates. Performance calculations are presented for ambient temperatures close to 480 R (20 F) and 535 R (75 F) which simulate seasonal aircraft operating conditions. Resulting thrust augmentation ratios are presented as functions of nozzle pressure ratio and temperature.

Barankiewicz, Wendy S.↗

NASA NTRS1991

Static performance tests of a flight-type STOVL ejector

Barankiewicz, Wendy S.↗

NASA NTRS1992

Frozen start-up behavior of low-temperature heat pipes

Start-up and subsequent operation of a low-temperature heat pipe requires the liquid phase of the operating fluid to be continuously pumped back to the evaporator by the capillary action of the wick. If the pipe has been in an environment where ambient temperatures are below the freezing point of the working fluid prior to start-up, the frozen fluid in the condenser and adiabatic region scan prevent initial flow to the evaporator, causing dryout of the evaporator before all of the working fluid is in the liquid phase. This paper examines the time-dependent wall and vapor temperature profiles along the axial length of a low-temperature heat pipe during start-up from the frozen state, and freeze-out during a normal operation by applying a subfreezing temperature fluid through the condenser. In addition, the experimental transient frozen start-up wall temperature profile is compared with a two-dimensional numerical phase-change model. A successful start-up method using a pulsed power input is presented.

Faghri, Amir↗

DOE OSTI2024

Low-temperature formation of Ti2AlN during post-deposition annealing of reactive multilayer systems

M n+1 AXn-phase Ti 2 AlN thin-films were synthesized using reactive sputtering-based methods involving the deposition of single-layer TiAlN, and Ti/AlN and TiN/TiAl multilayers of various modulation periods at ambient temperature and subsequent annealing at elevated temperatures. Ex situ and in situ x-ray diffraction measurements were used to characterize the Ti 2 AlN formation temperature and phase fraction. During annealing, Ti/AlN multilayers yielded Ti 2 AlN at a significantly lower in situ temperature of 650 °C compared to TiN/TiAl multilayers or single-layer TiAlN (750 °C). The results suggest a reactive multilayer mechanism whereby distinct Ti and AlN layers react readily to release exothermic energy resulting in lower phase transition temperatures compared to TiN and TiAl layers or mixed TiAlN. With a modulation period of 5 nm, however, Ti/AlN multilayers yielded Ti 2 AlN at a higher temperature of 750 °C, indicating a disruption of the reactive multilayer mechanism due to a higher fraction of low-enthalpy interfacial TiAlN within the film.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2021

Rapid dissolution of PuO 2 analytical samples using mediated electrochemical oxidation

Current methods for quantitative dissolution of solid PuO 2 involve lengthy dissolution times. The adaptation of mediated electrochemical oxidation, which uses an electrochemically produced oxidizing agent to catalyze dissolution, has been explored for radiochemical analysis scale dissolutions of PuO 2 . The effects of temperature, electrode material, and electrocatalyst on the dissolution kinetics were explored. Under conditions examined in this study, complete dissolution of tens of milligrams of solid PuO 2 can be achieved in less than 1 h at ambient temperature. Overall, this methodology could be adapted to dissolve other metal oxides.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2024

Effects of Warming and Elevated CO2 on Stomatal Conductance and Chlorophyll Fluorescence of C3 and C4 Coastal Wetland Species

Abstract Coastal wetland communities provide valuable ecosystem services such as erosion prevention, soil accretion, and essential habitat for coastal wildlife, but are some of the most vulnerable to the threats of climate change. This work investigates the combined effects of two climate stressors, elevated temperature (ambient, + 1.7 °C, + 3.4 °C, and 5.1 °C) and elevated CO 2 ( e CO 2 ), on leaf physiological traits of dominant salt marsh plant species. The research took place at the Salt Marsh Accretion Response to Temperature eXperiment (SMARTX) at the Smithsonian Environmental Research Center, which includes two plant communities: a C 3 sedge community and a C 4 grass community. Here we present data collected over five years on rates of stomatal conductance (g s ), quantum efficiency of PSII photochemistry ( F v / F m ), and rates of electron transport (ETR max ). We found that both warming and e CO 2 caused declines in all traits, but the warming effects were greater for the C 3 sedge. This species showed a strong negative stomatal response to warming in 2017 and 2018 (28% and 17% reduction, respectively in + 5.1 °C). However, in later years the negative response to warming was dampened to < 7%, indicating that S. americanus was able to partially acclimate to the warming over time. In 2022, we found that sedges growing in the combined + 5.1 °C e CO 2 plots exhibited more significant declines in g s , F v /F m , and ETR max than in either treatment individually. These results are important for predicting future trends in growth of wetland species, which serve as a large carbon sink that may help mitigate the effects of climate change.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1981

Very low threshold-current temperature sensitivity in constricted double-heterojunction AlGaAs lasers

The temperature dependence of threshold currents in constricted double-heterojunction diode lasers with strong lateral mode confinement is found to be significantly milder than for other types of lasers. The threshold-current relative variations with ambient temperature are typically two to three times less than for other devices of CW-operation capability. Over the interval 10-70 C the threshold currents fit the empirical exponential law exp/(T2-T1)/T0/ with T0 values in the 240-375 C range in pulsed operation, and in the 200-310 C range in CW operation. The external differential quantum efficiency and the mode far-field pattern near threshold are virtually invariant with temperature. The possible causes of high-T0 behavior are analyzed, and a new phenomenon - temperature-dependent current focusing - is presented to explain the results.

Botez, D.↗

NASA NTRS1993

A full-scale STOVL ejector experiment

The design and development of thrust augmenting short take-off and vertical landing (STOVL) ejectors has typically been an iterative process. In this investigation, static performance tests of a full-scale vertical lift ejector were performed at primary flow temperatures up to 1560 R (1100 F). Flow visualization (smoke generators, yarn tufts and paint dots) was used to assess inlet flowfield characteristics, especially around the primary nozzle and end plates. Performance calculations are presented for ambient temperatures close to 480 R (20 F) and 535 R (75 F) which simulate 'seasonal' aircraft operating conditions. Resulting thrust augmentation ratios are presented as functions of nozzle pressure ratio and temperature. Full-scale experimental tests such as this are expensive, and difficult to implement at engine exhaust temperatures. For this reason the utility of using similarity principles -- in particular, the Munk and Prim similarity principle for isentropic flow -- was explored. At different primary temperatures, exit pressure contours are compared for similarity. A nondimensional flow parameter is then shown to eliminate primary nozzle temperature dependence and verify similarity between the hot and cold flow experiments. Under the assumption that an appropriate similarity principle can be established, then properly chosen performance parameters should be similar for both hot flow and cold flow model tests.

Barankiewicz, Wendy S.↗

NASA NTRS1974

Data book for 12.5-inch diameter SRB thermal model water flotation test; 1.29 psia, series P022

Data acquired from tests conducted to determine how thermal conditions affect SRB (Space Shuttle Solid Rocket Booster) flotation at a scaled pressure of 1.29 psia are presented. Included are acceleration, pressure, and temperature data recorded from initial water impact to final flotation position using a 12.5-inch diameter thermal model of the SRB. Nineteen valid tests were conducted. These thermal tests indicated the following basic differences relative to the ambient temperature and pressure model tests: (1) more water was taken on board during penetration and (2) model flotation/sinking was temperature sensitive.

Allums, S. L.↗

NASA NTRSDate not supplied

Nutrient Stability in NASA Spaceflight Experiment Rodent Food Bars

Nutrient-upgraded Rodent Food Bars are the standard diet for mice involved in spaceflight experiments aboard the International Space Station as part of NASA’s Rodent Research Project. These Food Bars are a twin-screw extruded AIN-93G based product with nutrient additives to preserve a healthy and complete diet for the animals, and the bar form factor is necessary for use in the microgravity environment. Due to the nature of NASA flight projects and the lengthy production process of these Food Bars, a shelf-life assessment was undertaken to determine nutrient stability over an extended storage time. To assess palatability and stability over an extended duration, a panel of lipid oxidation markers and both fat- and water-soluble vitamins were assessed under various time and temperature conditions via AOAC International standardized methodology. Thiamine was the least stable vitamin at room temperature. Bars that had been continually kept at 4C (t=6, 12, 27 months) showed significantly higher levels of thiamine (via Student’s t-test) compared to all other bars that underwent some degree of ambient temperature storage. This suggests that refrigeration is a key component in maintaining adequate nutrient levels in these relatively high moisture (average 29.3%) food bars. Also of note was the level of Vitamin A in the form of retinol. There was no correlation to storage temperature, but rather the only factor having an effect on retinol levels was time. As low, yet consistent decrease in retinol was observed over the course of the experiment, though at no time did the retinol levels drop below the rodent Nutrient Requirements for Laboratory Animals (NRC). In conclusion, over the 27-month time course, all analyzed vitamins and lipid oxidation factors remained relatively stable and at levels which provide fully sufficient nutrition to rodents during spaceflight. Some groups however, displayed higher-than-expected aerobic and anaerobic bacteria colony forming units, which is believed to stem from a since-revised handling technique.

Food↗

DOE OSTI2023

Green mechanochemical synthesis of imine-linked covalent organic frameworks for high iodine capture

Covalent organic frameworks (COFs) have emerged as promising adsorbents for radioiodine capture. However, the conventional solvothermal synthesis contradicts the principles of green chemistry due to the use of hazardous solvents, long reaction times (typically 3 days), and high reaction temperatures. Here, to address these issues, we demonstrate for the first time the green, efficient, liquid-assisted mechanochemical synthesis of COF adsorbents for high iodine capture. The ball milling synthesis was performed with various liquid additives at ambient temperature, yielding six imine-linked COFs of diverse pore sizes and functionalities in merely 1 hour. Notably, one representative COF exhibited high crystallinity and a remarkable surface area of 1387 m 2 g –1 in just 1 minute of ball milling. When tested as adsorbents for static iodine vapor capture at 75 °C, four mechanochemically synthesized COFs exhibited outstanding iodine adsorption capacities of 6.4–7.1 g g –1 , comparable to or exceeding those of solvothermally synthesized COF and most reported COF adsorbents. Furthermore, Fourier transform infrared and X-ray photoelectron spectroscopy corroborated the charge transfer between iodine and COF adsorbents. This mechanochemical methodology will pave the path for green, rapid, facile, and scalable synthesis of COFs, revealing great prospects for applications in environmental remediation and beyond.

36 MATERIALS SCIENCE↗

NASA NTRS1988

Non-thermal distribution of O(1D) atoms in the night-time thermosphere

The 6300 A O(1D-3P) emission has been used for many years to remotely monitor the thermospheric temperature from the Doppler width of its line profile. The O(1D) atoms in the nighttime thermosphere are initially produced by the dissociative recombination of O2(+) ions with kinetic energy much greater than the thermal energy of the ambient neutrals. The validity of the technique to monitor neutral ambient temperature by measuring O(1D) 6300 A emission depends on the degree of thermalization of the O(1D) atoms. The object of this study is to calculate the velocity distribution of the O(1D) atoms and to examine the effect of nonthermal distribution on the nighttime thermospheric neutral temperature determined.

Yee, Jeng-Hwa↗

NASA NTRS1992

Two-dimensional thermal modeling of power monolithic microwave integrated circuits (MMIC's)

Numerical simulations of the two-dimensional temperature distributions for a typical GaAs MMIC circuit are conducted, aiming at understanding the heat conduction process of the circuit chip and providing temperature information for device reliability analysis. The method used is to solve the two-dimensional heat conduction equation with a control-volume-based finite difference scheme. In particular, the effects of the power dissipation and the ambient temperature are examined, and the criterion for the worst operating environment is discussed in terms of the allowed highest device junction temperature.

Fan, Mark S.↗

DOE OSTI2024

Room‐Temperature Formate Ester Transfer Hydrogenation Enables an Electrochemical/Thermal Organometallic Cascade for Methanol Synthesis from CO 2

Abstract The reduction of CO 2 to synthetic fuels is a valuable strategy for energy storage. However, the formation of energy‐dense liquid fuels such as methanol remains rare, particularly under low‐temperature and low‐pressure conditions that can be coupled to renewable electricity sources via electrochemistry. Here, a multicatalyst system pairing an electrocatalyst with a thermal organometallic catalyst is introduced, which enables the reduction of CO 2 to methanol at ambient temperature and pressure. The cascade methanol synthesis proceeds via CO 2 reduction to formate by electrocatalyst [Cp*Ir(bpy)Cl] + (Cp*=pentamethylcyclopentadienyl, bpy=2,2′‐bipyridine), Fischer esterification of formate to isopropyl formate catalyzed by trifluoromethanesulfonic acid (HOTf), and thermal transfer hydrogenation of isopropyl formate to methanol facilitated by the organometallic catalyst (H‐PNP)Ir(H) 3 (H‐PNP=HN(C 2 H 4 P i Pr 2 ) 2 ). The isopropanol solvent plays several crucial roles: activating formate ion as isopropyl formate, donating hydrogen for the reduction of formate ester to methanol via transfer hydrogenation, and lowering the barrier for transfer hydrogenation through hydrogen bonding interactions. In addition to reporting a method for room‐temperature reduction of challenging ester substrates, this work provides a prototype for pairing electrochemical and thermal organometallic reactions that will guide the design and development of multicatalyst cascades.

Fernández, Sergio [Department of Chemistry Univers↗

DOE OSTI2026

Thermal Regulation of CO 2 Activation Pathways via Interfacial Water Restructuring Enables Ampere-Level, Near-Unity CO Electrosynthesis

Electrochemical reduction of CO 2 to CO is a key step in carbon utilization technologies, yet maintaining high CO selectivity under elevated temperatures relevant to industrial membrane-electrode-assembly (MEA) electrolyzers remains challenging due to the competing hydrogen evolution reaction (HER). Additionally, the temperature dependence of CO selectivity on Cu-based catalysts has remained largely unexplored. Here, we demonstrate that incorporating atomic In or Sn into Cu fundamentally reshapes the selectivity of Cu catalysts at elevated temperatures. Dilute alloy catalysts, In 1 Cu and Sn 1 Cu, achieve >95% FE of CO over a broad current-density window (0.1−1.1 A cm −2 ) at 60 °C in MEA electrolyzers, far exceeding their performance at ambient temperature. In situ attenuated total reflection surface-enhanced infrared absorption spectroscopy suggests that elevating temperature depletes interfacial water activity, which favors a shift in CO 2 activation from a proton-coupled *COOH pathway toward an electron-driven *COO − -associated pathway, while also suppressing HER and CO hydrogenation. In contrast, benchmark CO-selective catalysts such as Ag exhibit minimal temperature-induced changes in CO production at 20−60 °C. These findings identify temperature as an unavoidable yet previously underutilized operating parameter in MEA electrolyzers for high-rate, selective CO production on Cubased catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1988

Cost effective alternative to low irradiance measurements

Martin Marietta's Space Simulation Laboratory (SSL) has a Thermal Environment Simulator (TES) with 56 individually controlled heater zones. The TES has a temperature range of approximately minus 129 C to plus 149 C. Because of the ability of TES to provide complex irradiance distributions, it is necessary to be able to measure a wide range of irradiance levels. SSL currently uses ambient temperature controlled radiometers with the capacity to measure sink irradiance levels of approximately 42.6 mw/sq cm, sink temperature equals 21 C and up. These radiometers could not be used to accurately measure the lower irradiance levels of the TES. Therefore, it was necessary to obtain a radiometer or develop techniques which could be used to measure lower irradiance levels.

Oleary, Scott T.↗

NASA NTRS2003

CO2 capture by means of an enzyme-based reactor

We report a means for efficient and selective extraction of carbon dioxide (CO(2)) at low to medium concentration from mixed gas streams. CO(2) capture was accomplished by use of a novel enzyme-based, facilitated transport contained liquid membrane (EBCLM) reactor. The parametric studies we report explore both structural and operational parameters of this design. The structural parameters include carbonic anhydrase (CA) concentration, buffer concentration and pH, and liquid membrane thickness. The operational parameters are temperature, humidity of the inlet gas stream, and CO(2) concentration in the feed stream. The data show that this system effectively captures CO(2) over the range 400 ppm to at least 100,000 ppm, at or around ambient temperature and pressure. In a single pass across this homogeneous catalyst design, given a feed of 0.1% CO(2), the selectivity of CO(2) versus N(2) is 1,090 : 1 and CO(2) versus O(2) is 790 :1. CO(2) permeance is 4.71 x 10(-8) molm(-2) Pa(-1) sec(-1). The CLM design results in a system that is very stable even in the presence of dry feed and sweep gases.

NASA Discipline Life Support Systems↗

NASA NTRS1984

Meteoritic constraints on processes in the solar nebula

High-temperature events or processes in the solar nebula were required to form the chondrules and CAI's that make up the bulk of the substance of most chondrites. There is no consensus in the meteoritical community as to the nature of these high-temperature events or processes. In spite of this major area of uncertainty several conclusions can be reached about properties of the nebula. The chondrules and CAI's were formed in regions where the dust/gas ratio was orders of magnitude above the cosmic value. After these high-temperature objects were formed, they began to accrete very promptly (a time scale of hours, probably). Formation and aggregation of the chondrite components happened at the same radial distance in the nebula where chondrites reside today (the asteroid belt). The ambient temperature of the nebula at that time and place was relatively low ( 700 K), and was not responsible for the thermal processing of the chondrules and CAI's.

Wood, J. A.↗