Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “alloy development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Deformation Behavior of β Phase in a WE54 Magnesium Alloy

Second phases play a significant role in the development of high-performance magnesium alloys with rare earth elements. Here, in situ tensile tests combined with synchrotron radiation were carried out to investigate the deformation behavior of β phases in a WE (Mg–Y–Gd–Nd) alloy. By lattice strain analysis, it was found that micro load continuously transferred from the soft α-Mg matrix to the hard β phases during the whole plastic deformation, while this behavior was much more obvious at the beginning of deformation. Based on diffraction peak broadening, Williamson–Hall (W–H) plotting was used to study the microstrain of β phases. The results showed that the microstrain of β phases increased rapidly within 4% plastic strain and reached the maximum at plastic strain of ~6.5%. Since the β phases acted as hard phases, the microstrain was considered as a sign of the stress concentration near phase interfaces. It was also suggested that the effective release of local stress concentration at the β/α-Mg interface benefited the ductility of the WE alloy by the plastic deformation of β phases and phase interface sliding.

36 MATERIALS SCIENCE↗
NASA NTRS1986

Study on effects of powder and flake chemistry and morphology on the properties of Al-Cu-Mg-X-X-X powder metallurgy advanced aluminum alloys

A study was conducted: (1) to develop rapid solidification processed (RSP) dispersoid-containing Al-3Cu-2Li-1Mg-0.2Zr alloys as substitutes for titanium alloys and commercial 2XXX aluminum alloys for service to at least 150 C; and (2) to develop RSP Al-4Li-Cu-Mg-Zr alloys as substitutes for high-strength commercial 7XXX alloys in ambient-temperature applications. RSP Al-3Cu-2Li-1Mg-0.2Zr alloys have density-normalized yield stresses at 150 C up to 52% larger than that of 2124-T851 and up to 30% larger than that of Ti-6Al-4V. Strength at 150 C in these alloys is provided by thermally stable delta' (Al3Li), T1 (Al2LiCu), and S' (Al2CuMg) precipitates. Density-normalized yield stresses of RSP Al-3Cu-2Li-1Mg-0.2Zr alloys are up to 100% larger than that of 2124-T851 and equivalent to that of Al-8Fe-4Ce at 260 C. Strength in the RSP alloys at 260 C is provided by incoherent dispersoids and subboundary constituent particles such as T1 and S. The RSP alloys are attractive substitutes in less than or = 100-h exposures for 2xxx and Al-4Fe-Ce alloys up to 260 C and for titanium alloys up to 150 C. RSP Al-4Li-Cu-Mg-Zr alloys have ambient-temperature yield and ultimate tensile stresses similar to that of 7050-T7651, and are 14% less dense. RSP Al-4Li-0.5Cu-1.5Mg-0.2Zr has a 20% higher specific yield stress, 40% higher specific elastic modulus, and superior corrosion resistance compared to the properties of 7050-T7651. Strength in the Al-4Li-Cu-Mg-Zr alloy class is primarily provided by the substructure and delta' precipitates and is independent of Cu:Mg ratio. Improvements in fracture toughness and transverse-orientation properties in both alloy classes depend on improved melt practices to eliminate oxide inclusions which are incorporated into the consolidated forms.

Meschter, P. J.↗
DOE OSTI2025

Development of Predictive Model for Accurate Rupture Time from Multi-Axial Creep in Alloy 709 with Physics-Based Simulations

A physics-based model is developed to predict multiaxial creep behavior in Alloy 709 (A709), an advanced austenitic stainless steel intended for high-temperature applications such as Sodium Fast Reactors (SFRs). Compared to conventional stainless steels like 316H, A709 offers superior high-temperature performance; however, comprehensive data on its multiaxial creep response remain limited. To address this gap, a crystal plasticity finite element (CPFE) framework is used to simulate the deformation and failure mechanisms of A709 under multiaxial loading conditions. The model incorporates an extended Hu-Cocks dislocation creep formulation that accounts for precipitation effects, along with the Sham–Needleman model to capture grain boundary cavitation-driven failure. These advanced constitutive models enable a detailed understanding of the interplay between microstructural evolution and macroscopic creep response. Furthermore, the study evaluates the predictive accuracy of various effective stress measures in estimating creep rupture life, leveraging simulated multiaxial creep data. The findings provide critical insights into the applicability of different stress measures for engineering design and life prediction of A709 components operating under complex loading conditions. This work contributes to improving the reliability of high-temperature structural components by advancing predictive modeling capabilities for advanced austenitic steels.

Alloy 709↗
DOE OSTI2022

A709 Qualification Plan Update and Mechanical Properties Data Assessment

This report provides a summary of the development effort for the qualification of Alloy 709, an advanced austenitic stainless steel, in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors. It provides an assessment of the mechanical properties data generated to date from the tensile, creep, fatigue and creep-fatigue tests of the precipitation-treated Alloy 709 from two commercial heats in plate product form. It was concluded that the mechanical properties of Alloy 709 with the precipitation treatment continued to outperform those of Type 316 stainless steel. This affirms the recommendation to Code qualification this alloy as a replacement for Type 316 stainless steel to support the objective of reducing the construction and operating costs to incentivize advanced reactor deployment. The data also demonstrated that the precipitation treatment is effective in enhancing the creep-fatigue resistance of Alloy 709 while maintaining a significant creep strength advantage over Type 316 stainless steel. This report also provides an update to the test conditions for the creep, fatigue and creep-fatigue test matrices in order to cover the Code Case data package more effectively. Finally, it is recommended to continue the Alloy 709 Code Case Testing Program to develop the data package needed for the determination of the material-specific design parameters for inclusion in the Alloy 709 Code Case.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1989

Measurement Of Composition In Transparent Model Alloy

Variation of FTIR technique developed to enable study of growth of cells of different solid phase in unidirectional solidification of these organic mixtures, which serve as transparent anologs of opaque monotectic metal alloys. Study of organic analogs expected to contribute to understanding of formation of aligned rods and particles in directional solidification of metal alloys. Advantage of technique is redistribution of material caused by solidification determined after fact, to very fine scale.

Kaukler, William F.↗
NASA NTRS1989

The Pv product required for the frictional ignition of alloys

NASA-White Sands has developed a frictional heating tester capable of evaluating the ignition properties of alloys in oxygen under friction conditions which involve rubbing. Sixteen alloys have been thus evaluated, yielding determinations of the product of the contact pressure and surface speed required for ignition in oxygen at 6.9 MPa; those which contained large Ni fractions manifested the greatest resistance to rubbing-induced ignition. The effect of the coefficient of friction is noted to be a major influence on ignition, and the results obtained indicate the value of frictional heating tests for environments involving frictional heating.

Stoltzfus, Joel M.↗
NASA NTRS2001

Friction Stir Welding of Steel Alloys

The friction stir welding process has been developed primarily for the welding of aluminum alloys. Other higher melting allows such, as steels are much more difficult to join. Special attention must be given to pin tool material selection and welding techniques. This paper addresses the joining of steels and other high melting point materials using the friction stir welding process. Pin tool material and welding parameters will be presented. Mechanical properties of weldments will also be presented. Significance: There are many applications for the friction stir welding process other than low melting aluminum alloys. The FSW process can be expanded for use with high melting alloys in the pressure vessel, railroad and ship building industries.

Ding, R. Jeffrey↗
DOE OSTI2020

Materials and Approaches for Mitigation of SOFC Cathode Degradation in SOFC Power Systems

Perovskites such as doped lanthanum manganite and cobaltite have been used successfully as a cathode material in SOFC power systems operating between 700-1000°C. The electrodes, however, remain prone to degradation in presence of Cr containing gas atmosphere under systems operating conditions. Cathode in SOFCs is considered as one of the largest contributors of electrochemical performance degradations, leading to significant increase in ohmic and non-ohmic losses as well as interfacial compound formation. These degradations are mostly irreversible due to permanent changes to chemical and morphological alterations in the electrodes, resulting in the blockage of triple phase boundary (TPB) sites and decrease in oxygen reduction reactions (ORR). Fundamental mechanistic understanding has been developed to elucidate the reaction pathways of electrode poisoning in electronically conducting electrodes (LSM) as well as mixed ionic and electronically conducting electrodes (LSCF). The overall goal of this program has been identification and development of cost effective solutions to mitigate electrode degradations under “real world” systems operating conditions. The overall technological innovations and impact from this work are: The research provides an understanding of the degradation mechanism and cost-effective approaches for implementation in SOFC systems; Develop mitigation processes utilizing low cost getters using conventional synthesis and fabrication route; Develop tailored high surface area powders and coatings for high Cr capture capacity under systems operating conditions; >Developed computational models to understand mechanistic behavior; Experimentally measure rate of Cr evaporation from chromia and alumina forming alloys under SOFC operating conditions; Developed conditions to minimize Cr evaporation from balance-of-plant alloys; This innovation will support the development of getter platform to capture both intrinsic and extrinsic impurities present in air; and, Applications under wide operating temperature range (500-900°C) as well for wide high-temperature electrochemical systems (SOFC, SOEC, and OTM). The work has been successfully developed, validated experimentally and implemented. Successful technology transfer of this knowledge with industrial partners has been accomplished and the getters have been independently tested and validated under their systems operating conditions. The innovation will also find application in related high temperature electrochemical systems such as OTM and SOEC for the prevention of Cr assisted performance degradation. The proposed approach for Cr capture can also be applied to oxy-combustion and other advanced combustion techniques for the reduction of Cr vapor in the exhaust gas stream. This fundamental knowledge gained also has led to the path forward for developing advanced getters for capturing more than one contaminant in air.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1999

Microstructural Development of Directionally Solidified Hg(1-x)Zn(x)Se Alloys

Hg(1-x)Zn(x)Se alloys have been studied as an alternative to Hg(1-x)Cd(x)Te for the detection of electromagnetic radiation, because the shorter ZnSe and HgSe bonds have been predicted to improve lattice stability. Several ingots with x = 0.1 were directionally solidified using a modified Bridgman-Stockbarger method; one was grown in an applied magnetic field, which greatly reduced radial compositional variations. A method was developed to reduce wetting. This, combined with the convex liquid-solid interface shape, produced boules that were single crystalline after growing about 3.5 cm. Observed surface features indicated ampoule wetting was eliminated using a graphite getter. Microstructural characteristics were greatly improved over HgCdTe alloys. In six boules, a total of only one twin was observed. A method for polishing and producing dislocation etch pits was developed for these alloys, revealing dislocation etch pit densities one to two orders of magnitude less than HgTe-based alloys. A kink in the thermal profile during processing of one boule generated more dislocations than did lattice mismatch due to compositional variations. This alloy has improved microstructural properties and resistance to dislocation formation compared with similar II-VI alloys.

Cobb, S. D.↗
DOE OSTI2025

Development of a thermal creep model for aluminum alloy 6061 cladding in U-10Mo monolithic fuel plates

Plate-type fuel elements consisting of a high-density, low-enriched uranium (LEU) U–10Mo-based fuel foil encapsulated in an aluminum alloy (AA) cladding are fabricated using the hot isostatic pressing (HIP) technique. During the HIP process, the fuel plate system is heated to 560 °C, then cooled to room temperature. This heat cycle significantly affects the mechanical properties of the aluminum cladding, and experimental investigations have shown that, post-HIP bonding, the mechanical properties of the aluminum cladding transition from those of AA 6061-T6 to something closer to the O temper. More specifically, the ultimate strength of the cladding decreases while its ductility increases, making it challenging to capture the changes in mechanical behavior and material properties. Understanding the residual stresses generated during the HIP process is critical for assessing the fuel plate’s integrity under various temperature, pressure, and irradiation. To simulate the HIP bonding process, the elastic, plastic, and thermal properties of the cladding are assumed to be similar to those of AA 6061-O temper. However, the primary challenge lies in the lack of available data for the creep model of the AA 6061 cladding during this transient process of HIP. The present study focuses on developing a computational model that predicts the creep behavior of the aluminum cladding in the fuel plates during the HIP process, as cladding creep significantly influences the residual stresses generated in U-10Mo fuel plates during HIP fabrication. Furthermore, as HIP bonding occurs at high temperatures that are nearing the melting point of aluminum, the present work considered a temperature-dependent Arrhenius-type creep model. In particular, a hyperbolic sine creep model is employed to estimate the creep properties of the as-fabricated aluminum cladding. In conclusion, the residual stresses predicted in the U-10Mo fuel when using the newly calibrated creep model closely align with the experimental measurements, validating the model’s accuracy.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Assessment of preliminary results of baseline high entropy alloys manufactured at INL

Materials development is needed to support the design and deployment of advanced nuclear reactors that will operate at higher temperatures and in harsher environments than the current light water reactor fleet. High entropy alloys have been identified as a class of alloy that could address the needs of advanced reactors, such as the molten salt reactors, due to their potential strength, radiation resistance, and corrosion resistance. This project summarizes the work done in fiscal year 2024 for the Additive Manufacturing of High Entropy Alloys for Nuclear Applications Project. This work has focused on examination of potential alloy compositions, down selection based on simulated results, and preliminary testing of down selected alloys.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Ignition characteristics of the nickel-based alloy UNS N07001 in pressurized oxygen

The development of ignition and combustion in pressurized oxygen atmospheres was studied for the nickel-based alloy UNS N07001. Ignition of the alloy was achieved by heating the top surface of a cylindrical specimen with a continuous-wave CO2 laser. Two heating procedures were used. In the first, laser power was adjusted to maintain an approximately linear increase in surface temperature. In the second, laser power was periodically increased until autoheating (self-heating) was established. It was found that the alloy would autoheat to combustion from temperatures below the solidus temperature. In addition, the alloy had a tendency to develop combustion zones (hot spots) at high oxygen pressures when the incremental (step) heating test mode was used. Unique points on the temperature-time curves that describe certain events are defined and the temperatures at which these events occur are given for the oxygen pressure range of 1.72 to 13.8 MPa (250 to 2000 psia).

Bransford, J. W.↗
NASA NTRS1999

Novel Directional Solidification Processing of Hypermonotectic Alloys

Gravity driven separation precludes uniform microstructural development during controlled directional solidification (DS) processing of hypermonotectic alloys. It is well established that liquid/liquid suspensions, in which the respective components are immiscible and have significant density differences, can be established and maintained by utilizing ultrasound. A historical introduction to this work is presented with the intent of establishing the basis for applying the phenomena to promote microstructural uniformity during controlled directional solidification processing of immiscible mixtures. Experimental work based on transparent organics, as well as salt systems, will be presented in view of the processing parameters.

Grugel, Richard N.↗
DOE OSTI2020

Development of Mischmetal–Fe–Co–B Permanent Magnet Alloys via High-Throughput Methods

Additive manufacturing synthesis using laser engineered net shaping (LENS) is utilized in this work to rapidly print libraries of mischmetal (MM = La, Ce, Nd, and Pr) containing R 2 TM 14 B alloys (R = MM + separated Nd and TM = Fe and Co) enabling robust evaluation of physical properties over a wide composition range. High-throughput characterization of the magnetic and thermal properties are used to identify compositions for potential high-temperature, high-performance permanent magnets with reduced critical rare-earth elements. Improved Curie temperature ( T c ~ 450 °C) is obtained with substitution of Fe by Co in pseudoternary R 2 TM 14 B alloys. Furthermore, a 4-fold decrease in the Nd content can be achieved through substitution with less critical Ce- and La-rich MM, while retaining high T c . Guided by the properties of the LENS printed samples, selected compositions with and without TiC additions are synthesized via melt-spinning techniques to produce nanostructured ribbons. The maximum room temperature coercivity ( H c ) and energy product ((BH) max ) without TiC are found to be 5.8 kOe, 8.5 MGOe, respectively, while TiC additions as a grain refiner gave H c and (BH) max of 4.9 kOe, 9.8 MGOe, respectively. Structural characterization of the melt-spun ribbons shows homogeneous grain refinement with TiC additions, which leads to an increase in the energy product.

36 MATERIALS SCIENCE↗