Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “actual”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

The use of antioptimization to compare alternative structural models

Structural models are usually tested by comparing their response with that of a reference structure (an actual structure or a more refined model) to a limited number of arbitrary loads. This test is not always reliable because the loads are arbitrary. An antioptimization-based method is proposed to test structural models. This method compares a structural model with a reference model or an actual structure under the worst loading case that maximizes the error in the model. Specifically, the method identifies the loading case that maximizes the difference between the responses of two models of the same structure using optimization. This method can be used to design experiments in order to validate a structural model. It can also be applied to identify damage in a structure by determining the load that maximizes the difference in the behavior of the damaged and the intact structure. The proposed method is illustrated by applying it to a plate and an automotive structure.

Gangadharan, S. N.↗
NASA NTRS1993

The cost of model reference adaptive control - Analysis, experiments, and optimization

In this paper the performance of Model Reference Adaptive Control (MRAC) is studied in numerical simulations and verified experimentally with the objective of understanding how differences between the plant and the reference model affect the control effort. MRAC is applied analytically and experimentally to a single degree of freedom system and analytically to a MIMO system with controlled differences between the model and the plant. It is shown that the control effort is sensitive to differences between the plant and the reference model. The effects of increased damping in the reference model are considered, and it is shown that requiring the controller to provide increased damping actually decreases the required control effort when differences between the plant and reference model exist. This result is useful because one of the first attempts to counteract the increased control effort due to differences between the plant and reference model might be to require less damping, however, this would actually increase the control effort. Optimization of weighting matrices is shown to help reduce the increase in required control effort. However, it was found that eventually the optimization resulted in a design that required an extremely high sampling rate for successful realization.

Messer, R. S.↗
NASA NTRS1993

Inference of cirrus cloud properties using satellite-observed visible and infrared radiances. II - Verification of theoretical cirrus radiative properties

The study presents a methodology developed to apply a parameterization of radiative transfer calculations to satellite analyses of cirrus clouds. Cloud heights and optical depths are derived from visible and IR window measurements taken during FIRE when cirrus clouds were present. Geostationary satellite retrievals are compared to lidar-derived cloud heights and retrievals from a polar-orbiting satellite taken at different angles to determine which theoretical models of scattering phase function and single-scattering albedo best represent actual cirrus clouds. Models using small scattering phase function and single-scattering albedo best represent actual cirrus clouds. It is concluded that interpretation of cirrus reflectance with water-droplet models leads to biased results. The cloud-height and optical depth biases can be minimized with the aid of the C20 or cirrostratus models.

Minnis, Patrick↗
NASA NTRS1992

A system for verifying models and classification maps by extraction of information from a variety of data sources

Recent updates to a geographical information system (GIS) called VICAR (Video Image Communication and Retrieval)/IBIS are described. The system is designed to handle data from many different formats (vector, raster, tabular) and many different sources (models, radar images, ground truth surveys, optical images). All the data are referenced to a single georeference plane, and average or typical values for parameters defined within a polygonal region are stored in a tabular file, called an info file. The info file format allows tracking of data in time, maintenance of links between component data sets and the georeference image, conversion of pixel values to `actual' values (e.g., radar cross-section, luminance, temperature), graph plotting, data manipulation, generation of training vectors for classification algorithms, and comparison between actual measurements and model predictions (with ground truth data as input).

Norikane, L.↗
NASA NTRS1993

On the estimation algorithm for adaptive performance optimization of turbofan engines

The performance seeking control (PSC) algorithm is designed to continuously optimize the performance of propulsion systems. The PSC algorithm uses a nominal propulsion system model and estimates, in flight, the engine deviation parameters (EDPs) characterizing the engine deviations with respect to nominal conditions. In practice, because of measurement biases and/or model uncertainties, the estimated EDPs may not reflect the engine's actual off-nominal condition. This factor has a direct impact on the PSC scheme exacerbated by the open-loop character of the algorithm. In this paper, the effects produced by unknown measurement biases over the estimation algorithm are evaluated. This evaluation allows for identification of the most critical measurements for application of the PSC algorithm to an F100 engine. An equivalence relation between the biases and EDPs stems from the analysis; therefore, it is undecided whether the estimated EDPs represent the actual engine deviation or whether they simply reflect the measurement biases. A new algorithm, based on the engine's (steady-state) optimization model, is proposed and tested with flight data. When compared with previous Kalman filter schemes, based on local engine dynamic models, the new algorithm is easier to design and tune and it reduces the computational burden of the onboard computer.

Espana, Martin D.↗
NASA NTRS1993

Liquid rocket propulsion dynamic flow modeling using the ROCETS engineering modules in the EASY5x environment

A report on the progress of porting the ROCETS (ROCket Engine Transient Simulator) into the EASY5x simulation environment is presented. Brief descriptions of each of the software systems, information regarding the actual port process, and examples comparing the results of the two systems are given. It is shown that EASY5x is a suitable environment for utilization of the ROCETS engineering modules, and that, for the example systems shown, EASY5x actually seems to give more accurate solutions than the straight ROCETS code.

Follett, Randolph F.↗
NASA NTRS1923

Notes on aerodynamic forces on airship hulls

For a first approximation the air flow around the airship hull is assumed to obey the laws of perfect (i.e. free from viscosity) incompressible fluid. The flow is further assumed to be free from vortices (or rotational motion of the fluid). These assumptions lead to very great simplifications of the formulae used but necessarily imply an imperfect picture of the actual conditions. The value of the results depends therefore upon the magnitude of the forces produced by the disturbances in the flow caused by viscosity with the consequent production of vortices in the fluid. If these are small in comparison with the forces due to the assumed irrotational perfect fluid flow the results will give a good picture of the actual conditions of an airship in flight.

Tuckerman, L B↗
NASA NTRS1928

Combustion time in the engine cylinder and its effect on engine performance

As part of a general program to study combustion in the engine cylinder and to correlate the phenomena of combustion with the observed performance of actual engines, this paper presents a sketchy outline of what may happen in the engine cylinder during the burning of a charge. It also suggests the type of information needed to supply the details of the picture and points out how combustion time and rate affect the performance of the engine. A theoretical concept of a flame front which is assumed to advance radially from the point of ignition is presented, and calculations based on the area and velocity of this flame and the density of the unburned gases are made to determine the mass rate of combustion. From this rate the mass which has been burned and the pressure at any instant during combustion are computed. This process is then reversed in an effort to determine actual rates of combustion and flame velocities from the pressures as recorded on indicator diagrams. The effects of different rates of combustion on engine performance are then discussed and the importance of proper spark advance is emphasized.

Marvin, Charles F , Jr↗
NASA NTRS1930

Flight Tests on U.S.S. Los Angeles. Part II : Stress and Strength Determination

The tests described in this report furnished data on the actual aerodynamic forces, and the resulting stresses and bending moments in the hull of the U. S. S. "Los Angeles" during as severe still-air maneuvers as the airship would normally be subjected to, and in straight flight during as rough air as is likely to occur in service, short of squall or storm conditions. The maximum stresses were found to be within the limits provided for in accepted practice in airship design. Normal flight in rough air was shown to produce forces and stresses about twice as great as the most severe still-air maneuvers. No light was thrown upon the forces which might occur in extreme or exceptional conditions, such as the storm which destroyed the "Shenandoah". The transverse aerodynamic forces on the hull proper were found to be small and irregular. Owing to the necessity of conserving helium, it was impossible to fly the airship in a condition of large excess of buoyancy or weight in order to determine the air pressure distribution at a fixed angle of pitch. However, there is every reason to believe that in that condition the forces on the actual airship are as close to the wind-tunnel results as can be determined by present type of pressure measuring apparatus. It is considered that most important data obtained are the coefficients of tail-surface forces and hull-bending moments. These are tabulated in this report.

Burgess, C P↗
NASA NTRS1939

General airplane performance

Equations have been developed for the analysis of the performance of the ideal airplane, leading to an approximate physical interpretation of the performance problem. The basic sea-level airplane parameters have been generalized to altitude parameters and a new parameter has been introduced and physically interpreted. The performance analysis for actual airplanes has been obtained in terms of the equivalent ideal airplane in order that the charts developed for use in practical calculations will for the most part apply to any type of engine-propeller combination and system of control, the only additional material required consisting of the actual engine and propeller curves for propulsion unit. Finally, a more exact method for the calculation of the climb characteristics for the constant-speed controllable propeller is presented in the appendix.

Rockfeller, W C↗
NASA NTRS1955

Theoretical and experimental investigation of heat transfer by laminar natural convection between parallel plates

Results are presented of a theoretical and experimental investigation of heat transfer involving laminar natural convection of fluids enclosed between parallel walls oriented in the direction of the body force, where one wall is heated uniformly, and the other is cooled uniformly. For the experimental work, parallel walls were simulated by using an annulus with an inner-to-outer diameter ratio near 1. The results of the theoretical investigation are presented in the form of equations for the velocity and temperature profiles and the ratio of actual temperature drop across the fluid to the temperature drop for pure conduction. No experimental measurements were made of the velocity and temperature profiles, but the experimental results are compared with theory on the basis of the ratio of the actual temperature drop to the temperature drop for pure conduction. Good agreement was obtained between theory and experiment for axial temperature gradients of 10 degrees F. per foot or larger.

Lietzke, A F↗
NASA NTRS1941

Comparison of automatic control systems

This report deals with a reciprocal comparison of an automatic pressure control, an automatic rpm control, an automatic temperature control, and an automatic directional control. It shows the difference between the "faultproof" regulator and the actual regulator which is subject to faults, and develops this difference as far as possible in a parallel manner with regard to the control systems under consideration. Such as analysis affords, particularly in its extension to the faults of the actual regulator, a deep insight into the mechanism of the regulator process.

Oppelt, W↗
NASA NTRS1936

Investigations on the amount of downwash behind rectangular and elliptical wings

The downwash behind a wing may be computed from the system of vortices created by the wing and which can be substituted for the latter. If the actual rolling-up process of the free vortex sheet is disregarded, the establishment of boundaries for the downwash factors is contingent upon the premise that no rolling up takes place or else that the developed tip vortices start direct on the effective line. The actual downwash factors for the rectangular wing are rather of the approximate magnitude of the values computable with the developed tip vortices starting direct on the wing.

Muttray, H↗
NASA NTRS1931

Landing impact of seaplanes

The theory of landing impact is briefly stated and the applicability of a previously suggested formula is extended. Theoretical considerations regarding impact measurements on models and actual seaplanes are followed by a brief description of the instruments used in actual flight tests. The report contains a description of the strength conditions and deals exhaustively with force measurements on the float gear of an "HE 9a" with flat-bottom and with V-bottom floats. The experimental data are given and compared with the theoretical results.

Pabst, Wilhelm↗
NASA NTRS1989

Application of statistical distribution theory to launch-on-time for space construction logistic support

The ability to launch-on-time and to send payloads into space has progressed dramatically since the days of the earliest missile and space programs. Causes for delay during launch, i.e., unplanned 'holds', are attributable to several sources: weather, range activities, vehicle conditions, human performance, etc. Recent developments in space program, particularly the need for highly reliable logistic support of space construction and the subsequent planned operation of space stations, large unmanned space structures, lunar and Mars bases, and the necessity of providing 'guaranteed' commercial launches have placed increased emphasis on understanding and mastering every aspect of launch vehicle operations. The Center of Space Construction has acquired historical launch vehicle data and is applying these data to the analysis of space launch vehicle logistic support of space construction. This analysis will include development of a better understanding of launch-on-time capability and simulation of required support systems for vehicle assembly and launch which are necessary to support national space program construction schedules. In this paper, the author presents actual launch data on unscheduled 'hold' distributions of various launch vehicles. The data have been supplied by industrial associate companies of the Center for Space Construction. The paper seeks to determine suitable probability models which describe these historical data and that can be used for several purposes such as: inputs to broader simulations of launch vehicle logistic space construction support processes and the determination of which launch operations sources cause the majority of the unscheduled 'holds', and hence to suggest changes which might improve launch-on-time. In particular, the paper investigates the ability of a compound distribution probability model to fit actual data, versus alternative models, and recommends the most productive avenues for future statistical work.

Morgenthaler, George W.↗
NASA NTRS1993

Progress in p(+)n InP solar cells fabricated by thermal diffusion

The performance results of our most recently thermally diffused InP solar cells using the p(+)n (Cd,S) structures are presented. We have succeeded in fabricating cells with measured AMO, 25 C V(sub oc) exceeding 880 mV (bare cells) which to the best of our knowledge is higher than previously reported V(sub oc) values for any InP homojunction solar cells. The cells were fabricated by thinning the emitter, after Au-Zn front contacting, from its initial thickness of about 4.5 microns to about 0.6 microns. After thinning, the exposed surface of the emitter was passivated by a thin (approximately 50A) P-rich oxide. Based on the measured EQY and J(sub sc)-V(sub oc) characteristics of our experimental high V(sub oc) p(+)n InP solar cells, we project that reducing the emitter thickness to 0.3 microns, using an optimized AR coating, maintaining the surface hole concentration of 3 x 10(exp 18)cm(sup -3), reducing the grid shadowing from actual 10.55 percent to 6 percent and reducing the contact resistance will increase the actual measured 12.57 percent AMO 25 C efficiency to about 20.1 percent. By using our state-of-the-art p(+)n structures which have a surface hole concentration of 4 x 10(exp 18)cm(sup -3) and slightly improving the front surface passivation, an even higher practically achievable AMO, 25 C efficiency of 21.3 percent is projected.

Flood, D. J.↗
NASA NTRS1993

GRO: Black hole models for gamma ray bursts

This grant deals with the production of gamma-ray bursts (GRB's) close to horizons of black holes (BH's), mainly via accretion of small chunks of matter onto extreme Kerr BH's. In the past year, we laid the ground work for actual calculations close to Kerr BH's. Because of technical reasons, actual work has only started very recently. Following the detailed list of research subprojects as per our original proposal, we have performed research in the following areas: spectrum calculation; burst dynamics; tidal capture and primordial cloud collapse; halo density profile; and capture of other objects.

Shaham, Jacob↗
NASA NTRS1993

Payload/GSE/data system interface: Users guide for the VPF (Vertical Processing Facility)

Payload/GSE/data system interface users guide for the Vertical Processing Facility is presented. The purpose of the document is three fold. First, the simulated Payload and Ground Support Equipment (GSE) Data System Interface, which is also known as the payload T-0 (T-Zero) System is described. This simulated system is located with the Cargo Integration Test Equipment (CITE) in the Vertical Processing Facility (VPF) that is located in the KSC Industrial Area. The actual Payload T-0 System consists of the Orbiter, Mobile Launch Platforms (MLPs), and Launch Complex (LC) 39A and B. This is referred to as the Pad Payload T-0 System (Refer to KSC-DL-116 for Pad Payload T-0 System description). Secondly, information is provided to the payload customer of differences between this simulated system and the actual system. Thirdly, a reference guide of the VPF Payload T-0 System for both KSC and payload customer personnel is provided.

Source record↗