SEARCH · Engineering Papers

Results for “Windows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Simultaneous Ice Water Content Measurements at Multiple Locations on the NASA DC-8 Aircraft during the 2018 HIWC RADAR Flight Campaign

Ice water content measurements were made simultaneously at three locations on the NASA DC-8 in natural, glaciated conditions during the 2018 High Ice Water Content RADAR flight campaign. The purpose of these measurements was to further evaluate efficiency factors of hot-wire total water content probes in glaciated conditions and investigate the enhancement of ice crystal concentrations near fuselage surfaces due to flow field inertial effects, and ice crystals impacting the nose, breaking up, and flowing downstream. The total water content measurements were made using either Science Engineering Associates Ice Crystal Detectors or Robust Probes. Three common sensors were mounted on an underwing canister considered to be in near free-flow conditions, a standoff from a fuselage window, and the nose of the fuselage near the pitot probes. The Ice Crystal Detector total water content sensor and Robust Probe sensor collection and retention efficiencies were evaluated through comparisons with the underwing Ice Crystal Detector and Robust Probe measurements to the IKP2 isokinetic evaporator probe, which provided the reference ice water content measurement. Local ice water content at the nose position was evaluated by comparing ratios of the nose and underwing ice crystal detectors to the IKP2. Local ice water content at the window-standoff location was also evaluated by comparing total water content sensor measurements from the window ice crystal detector to the measurements made with the underwing and nose Ice Crystal Detectors The key findings were: 1) the Ice Crystal Detector total water content sensor ice water content efficiency factor was similar to previous estimates, but reduced with increased ice crystal median mass diameter; 2) the ice water content at the fuselage nose location near the DC-8 pitot probes was approximately 2.5 times the freestream values – although this estimate is affected by a higher probe efficiency factor due to smaller particles in the debris cloud from impacts upstream of the probe; and 3) the ice water content at the 17” standoff from the port window varied from about 50% to 3 times freestream values in a complicated manner. Similar measurement locations are not uncommon on cloud research aircraft, where ice particle measurements may be subject to similar uncertainties.

o Aircraft Icing↗

NASA NTRS2021

Simultaneous Ice Water Content Measurements at Multiple Locations on the NASA DC-8 Aircraft during the 2018 HIWC RADAR Flight Campaign

Ice water content measurements were made simultaneously at three locations on the NASA DC-8 in natural, glaciated conditions during the 2018 High Ice Water Content RADAR flight campaign. The purpose of these measurements was to further evaluate efficiency factors of hot-wire total water content probes in glaciated conditions and investigate the enhancement of ice crystal concentrations near fuselage surfaces due to flow field inertial effects, and ice crystals impacting the nose, breaking up, and flowing downstream. The total water content measurements were made using either Science Engineering Associates Ice Crystal Detectors or Robust Probes. Three common sensors were mounted on an underwing canister considered to be in near free-flow conditions, a standoff from a fuselage window, and the nose of the fuselage near the pitot probes. The Ice Crystal Detector concave total water content sensor and Robust Probe sensor collection and retention efficiencies were evaluated through comparisons with the underwing Ice Crystal Detector and Robust Probe measurements to the Isokinetic Probe version 2 (IKP2), which provided the reference ice water content measurement. Local ice water content at the nose position was evaluated by comparing ratios of the nose and underwing ice crystal detectors to the IKP2. Local ice water content at the window-standoff location was also evaluated by comparing total water content sensor measurements from the window probes to the measurements made with the underwing and nose probes. The key findings were: (1) the Ice Crystal Detector concave water content sensor efficiency factor to glaciated conditions was similar to previous estimates, but reduced with increased ice crystal median mass diameter; (2) the ice water content at the fuselage nose location near the DC-8 pitot probes was approximately 2.5 times the freestream values—although this estimate is affected by a higher probe efficiency factor due to smaller particles in the debris cloud from impacts upstream of the probe; and (3) the ice water content at the 17 in. standoff from the port window varied from about 50 percent to nearly three times freestream values in a complicated manner. Similar measurement locations are not uncommon on cloud research aircraft, where ice particle measurements may be subject to similar uncertainties.

Aircraft Icing↗

NASA NTRS2016

Category B Plastic Pane Testing for JSC 66320 Rev A Requirements Verifiable Through Acceptance Testing

JSC 66320, Revision A, Optical Property Requirements for Glasses, Ceramics, and Plastics in Spacecraft Window Systems, lists several quantitative requirements that spacecraft windowpanes must meet. Recently, we were asked to establish a capability at the Kennedy Space Center to perform these measurements on category B plastic panes, i.e., plastic panes that could be used on a spacecraft for long-focal-length photography and piloting. Two of the criteria, normal wavefront and 30-degree wavefront attributes, can be measured with existing equipment and processes (see NASA TM NESC-RP-14-00951, April 2016) and are not discussed in this document. However, the other six criteria-haze, wedge angle, birefringence, reflectance, transmittance, and color balance-required substantial development and are the subject of this document. In this document, we do not discuss the rationale behind the requirements, but we did engage in discussions with the authors of JSC 66320 in order to better understand the requirements and the verifications being imposed on windows and their testing. Accordingly, this document presents our best understanding of the requested requirements and verifications. We also present our methodology for performing each of the six measurements, along with applicable mathematics and a description, with photos, of the hardware used. In addition, we supply the results of a test on a low-quality in-house plastic window as an example of the system operation. Only requirements that can be met by acceptance test and analysis, as opposed to optical inspection, are considered in this document.

spaceflight windows↗

NASA NTRSDate not supplied

Residual Strength of Hypervelocity Impacted Silica

Windows in the International Space Station are subjected to on-going micrometeoroid and orbital debris damage (MMOD). The reliability of the windows is being ensured by monitoring of damage, life prediction, and measurement of the residual strength of man-made and natural hypervelocity impact damage. The residual strength of man-made craters and MMOD craters harvested from space shuttle windows were used to estimate strength as a function of damage dimensions and thereby derive design allowables for U.S. and Russian fused silicas used in the ISS. US and Russian silica exhibit similar mechanical properties. An effect of impact angle is apparent, with 0o impacts exhibiting the lowest strength for Russian quartz-derived silica. The crater morphology for fused silica consists of a central pit, crush zone, shallow rings and radial cracks dividing petaloids. Morphology of alkaline glass is different from than that of fused silica, with a more distinct pit and pulverized region, and bell and tail-like features below the pit.

Silicia↗

NASA NTRS1965

Detection of, and communication with space vehicles during atmospheric entry, problems in simulation

In considering the problem of communicating with outer space and detection of spacecraft from the ground, one usually has to worry about only the propagation characteristics of electromagnetic waves of vacuum wavelength falling within either one of the two well known "atmospheric windows," namely; (1) the "optical window" extending from about 0.3 microns to a few microns, and (2) the "RF window" extending from a few millimeters to about 30 meters in the wavelength scale. However, during entry (or reentry) of a spacecraft into the earth's atmosphere, there exists two physical phenomena which tend to complicate the communication problem on the one hand, and to simplify the detection problem on the other hand.

Detection↗

NASA NTRS1972

A multispectral technique to determine sea surface temperature using Nimbus 2 data.

Three channels of the Nimbus 2 five-channel Medium Resolution Infrared Radiometer have been employed in the development of a technique to determine sea surface temperature. Two of the channels in the 0.2-4.0 and 6.4-6.9 micron spectral regions are used to indicate a cloud-free line of sight and the third, a high signal-to-noise window channel (10-11 microns), measures the equivalent blackbody temperature (Tbb) which is a function of the thermal emission from the sea surface and the intervening atmosphere. Equivalent blackbody temperatures and normalized reflectance thresholds were established using frequency distributions from the 6.4-6.9 and 0.2-4.0 micron channels, respectively, to determine the existence of cloud-free conditions. The window Tbb's were compared with ship ocean temperature measurements for a one-month period over the western North Atlantic. This comparison revealed a plus or minus 1.5 K dispersion about the mean difference between the ship temperatures and window Tbb's between 31-34 N.

Shenk, W. E.↗

NASA NTRS1972

Space shuttle orbiter windshield system design and test

The development and testing of primary structural elements that are necessary to design a windshield system for the space shuttle orbiter are summarized. The elements include the outer (heat shield) panes, the inner pressure panes, the seals for both panes, and components of both window frames. One test article representing a pressure pane, including frames and seals, was tested under two sets of conditions. One set represented 100 mission cycles with temperature and pressure typical of those exerted on the innermost pane of the three-pane window system, and the second set represented 100 mission cycles with temperature and pressure typical of those exerted on a middle pane. A second test article representing an outer (heat sheild) pane was tested to conditions of 120 entry cycles, which equates to 100 entry cycles plus sufficient fatigue on the pane to account for 100 boost cycles. All elements of the design survived the test conditions in good condition. Window system for the shuttle orbiter vehicle.

Hayashida, K.↗

NASA NTRS1973

Preliminary flight trajectories for the Apollo Soyuz test project

Preliminary data are documented for a typical launch window opening, a typical in-plane case, and a typical launch window closing trajectory, not necessarily in the same daily launch window, for the Apollo Soyuz test project mission. The Soyuz will be launched first and the Apollo will be launched on the first opportunity, 7 hours 21 minutes later. If the Apollo is unable to be launched on the first opportunity, four additional opportunities are available at 30 hours 56 minutes, 54 hours 31 minutes, 78 hours 05 minutes, and 101 hours 40 minutes. If the Apollo cannot be launched in this time frame, no further attempt will be made to launch and rendezvous with the first Soyuz. Soyuz will then be deorbited; however, a second Soyuz was made available for the same purposes.

Brooks, J. D.↗

NASA NTRS1974

Optically detonated explosive device

A technique and apparatus for optically detonating insensitive high explosives, is disclosed. An explosive device is formed by containing high explosive material in a house having a transparent window. A thin metallic film is provided on the interior surface of the window and maintained in contact with the high explosive. A laser pulse provided by a Q-switched laser is focussed on the window to vaporize the metallic film and thereby create a shock wave which detonates the high explosive. Explosive devices may be concurrently or sequentially detonated by employing a fiber optic bundle to transmit the laser pulse to each of the several individual explosive devices.

Yang, L. C.↗

NASA NTRS1973

Systems design study of the Pioneer Venus spacecraft. Appendices to volume 1, sections 3-6 (part 1 of 3)

The design is described of the Venus probe windows, which are required to measure solar flux, infrared flux, aureole, and cloud particles. Window heating and structural materials for the probe window assemblies are discussed along with the magnetometer. The command lists for science, power and communication requirements, telemetry sign characteristics, mission profile summary, mass properties of payloads, and failure modes are presented.

Source record↗

NASA NTRS1974

A simple method for the generation of organ and vessel contours from roentgenographic or fluoroscopic images

A simple method for outlining or contouring any area defined by a change in film density or fluoroscopic screen intensity is described. The entire process, except for the positioning of an electronic window, is accomplished using a small computer having appropriate softwave. The electronic window is operator positioned over the area to be processed. The only requirement is that the window be large enough to encompass the total area to be considered.

Newell, J. D.↗

NASA NTRS1975

The source of the electric field in the nightside magnetosphere

In the open magnetosphere model magnetic field lines from the polar caps connect to the interplanetary magnetic field and conduct an electric field from interplanetary space to the polar ionosphere. By examining the magnetic flux involved it is concluded that only slightly more than half of the magnetic flux in the polar caps belongs to open field lines and that such field lines enter or leave the magnetosphere through narrow elongated windows stretching the tail. These window regions are identified with the tail's boundary region and shift their position with changes in the interplanetary magnetic field, in particular when a change of interplanetary magnetic sector occurs. The circuit providing electric current in the magnetopause and the plasma sheet is extended across those windows; thus energy is drained from the interplanetary electric field and an electric potential drop is produced across the plasma sheet. The polar cap receives its electric field from interplanetary space on the day side from open magnetic field lines and on the night side from closed field lines leading to the plasma sheet. The theory described provides improved understanding of magnetic flux bookkeeping, of the origin of Birkeland currents, and of the boundary layer of the geomagnetic tail.

Stern, D. P.↗

NASA NTRS1976

LACIE performance predictor final operational capability program description, volume 1

The program EPHEMS computes the orbital parameters for up to two vehicles orbiting the earth for up to 549 days. The data represents a continuous swath about the earth, producing tables which can be used to determine when and if certain land segments will be covered. The program GRID processes NASA's climatology tape to obtain the weather indices along with associated latitudes and longitudes. The program LUMP takes substrata historical data and sample segment ID, crop window, crop window error and statistical data, checks for valid input parameters and generates the segment ID file, crop window file and the substrata historical file. Finally, the System Error Executive (SEE) Program checks YES error and truth data, CAMS error data, and signature extension data for validity and missing elements. A message is printed for each error found.

Source record↗

NASA NTRS1975

Infrared emission spectra of elastohydrodynamic contacts

A small diamond disk mounted as a window in a steel plate was covered with test fluid, and a weighted steel ball was rotated over the window so as to form a sliding elastohydrodynamic (EHD) contact region. Some of the radiant energy generated in this region, both in the fluid and at the boundaries, passed through the window into an infrared interferometer, giving rise to an emission spectrum. This spectrum could be separated into contributions from the fluid and from the ball surface, making it possible, by appropriate calibrations, to estimate their temperatures separately under operating conditions. Moreover, the shape of the discrete spectral bands of the fluid permitted some inferences on its state. Two fluids were studied under identical mechanical conditions, a polyester and a naphthenic oil, each containing an equal amount of polymethylstyrene as a spectral indicator. Differences of band intensity, band width, and frequency could, therefore, be attributed to differences in the behavior of the base fluid.

Lauer, J. L.↗

NASA NTRS1977

Optical scanning system for laser velocimeter

An optical system was developed to provide fast incremental scanning of a backscattered laser velocimeter focus point over a 36-cm distance. The system is used to measure flow velocities at 16 positions along its optical axis and to scan these 16 positions up to 30 times a second. Dwell time at each location is approximately 2 milliseconds. Sample volumes typically are 0.2 mm in diameter by 1.4 cm in length. The optical scanning system consists of a wheel containing plane parallel quartz windows of various thicknesses. The laser velocimeter beams are imaged to a primary focus within the dead airspace of an optical cell. The beams emerging from the cell pass through the windows of the scanning wheel. The refraction of the beams passing through the windows causes an apparent shift of the focus within the optical cell and hence in the test zone. Light scattered from the secondary focus within the test zone is concurrently collected and reimaged through the same optical path which originally projected the primary focus. The reimaged backscattered light containing the velocity information is then collected and focused onto a photomultiplier detector system to complete the scanned laser velocimeter optical system.

Rhodes, D. B.↗

NASA NTRS1977

Optical scanner

An optical scanner that sequentially focuses optical energy (light) at selected points in space is described. The essential component is a scanning wheel including several glass windows with each window having a different thickness. Due to this difference in thickness, the displacement of the emerging light from the incident light is different for each window. The scanner transmits optical energy to a point in space while at the same time receiving any optical energy generated at that point and then moves on to the next selected point and repeats this transmit and receive operation. It fills the need for a system that permits a laser velocimeter to rapidly scan across a constantly changing flow field in an aerodynamic test facility.

Rhodes, D. B.↗

NASA NTRS1978

Concorde noise-induced building vibrations: John F. Kennedy International Airport

Outdoor and indoor noise levels resulting from aircraft flyovers and certain nonaircraft events were recorded at eight homesites and a school along with the associated vibration levels in the walls, windows, and floors at these test sites. Limited subjective tests were conducted to examine the human detection and annoyance thresholds for building vibration and rattle caused by aircraft noise. Both vibration and rattle were detected subjectively in several houses for some operations of both the Concorde and subsonic aircraft. Seated subjects more readily detected floor vibrations than wall or window vibrations. Aircraft noise generally caused more window vibrations than common nonaircraft events such as walking and closing doors. Nonaircraft events and aircraft flyovers resulted in comparable wall vibration levels, while floor vibrations were generally greater for nonaircraft events than for aircraft flyovers. The relationship between structural vibration and aircraft noise is linear, with vibration levels being accurately predicted from overall sound pressure levels (OASPL) measured near the structure. Relatively high levels of structural vibration measured during Concorde operations are due more to higher OASPL levels than to unique Concorde-source characteristics.

Mayes, W. H.↗

NASA NTRS1978

The nuclear and ionic charge distribution particle experiments on the ISEE-1 and ISEE-C spacecraft

The ISEE-1 and ISEE-C instruments are designed to measure the elemental abundances, charge state composition, energy spectra, and angular distributions of energetic ions in the energy range 2 keV/charge to 80 MeV/nucleon and electrons between 75 and 1300 keV. The instrument consists of three sensor systems: (1) ULECA which is an electrostatic deflection system with rectangular solid-state detectors for the 3-560 keV/charge range; (2) ULEWATT which is a double dE/dX vs E thin-window flowthrough proportional counter/solid-state detector telescope for the 0.2-80 MeV/nucleon (Fe) range; and (3) ULEZEQ which is a combination of an electrostatic deflection analyzer and a thin-window dE/dX vs E system with thin-window proportional counter and position-sensitive solid-state detector. The applications of the instruments to solar and interplanetary phenomena and to magnetospheric acceleration and trapped particles are discussed.

Hovestadt, D.↗