Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WALLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

A numerical simulation of three-dimensional flow in an adaptive wall wind tunnel

Numerical simulations of three dimensional flows in a prototype adaptive wall wind tunnel are conducted at the Mach number of 0.6 to investigate: (1) wind tunnel wall interference, (2) active streamline control by varying air removal or injection along the walls, and (3) to develop a method for establishing wall boundary conditions for interference free flows. Wind tunnel wall interference could be controlled by using only the vertical velocity components. For the configuration tested, interference free flow with solid sidewalls can be approximated by using only floor and ceiling blowing/suction.

Mendoza, J. P.↗
NASA NTRS1984

Validation of a wall-interference assessment/correction procedure for airfoil tests in the Langley 0.3-meter Transonic Cryogenic Tunnel

Validation of a wall-interference assessment/correction (WIAC) procedure for a given facility requires its application to several sets of test data. It is necessary therefore to create a somewhat automated method for processing data through the various steps in the procedure. An automated procedure is also welcomed by the test engineer or eventual user in order to reduce the required effort and opportunity for error. Such a procedure has been developed for the Langley 0.3-m Transonic Cryogenic Tunnel using the TWINTN4 WIAC code. This code provides a four-wall, 2-D, transonic correction; that is, it accounts for sidewall boundary-layer effects, as well as for top and bottom wall effects on the airfoil tests. The TWINTN4 code utilizes measured pressure data at the tunnel walls and on the airfoil model; thus, classical homogeneous-wall boundary conditions are not used in the correction procedure.

Gumbert, C. R.↗
NASA NTRS1983

Wind Tunnel Wall Interference Assessment and Correction, 1983

Technical information focused upon emerging wall interference assessment/correction (WIAC) techniques applicable to transonic wind tunnels with conventional and passively or partially adapted walls is given. The possibility of improving the assessment and correction of data taken in conventional transonic wind tunnels by utilizing simultaneously obtained flow field data (generally taken near the walls) appears to offer a larger, nearer-term payoff than the fully adaptive wall concept. Development of WIAC procedures continues, and aspects related to validating the concept need to be addressed. Thus, the scope of wall interference topics discussed was somewhat limited.

Perry A. Newman↗
NASA NTRS1985

Apparatus and method to keep the walls of a free-space reactor free from deposits of solid materials

An apparatus and method is disclosed for keeping interior walls of a reaction vessel free of undesirable deposits of solid materials in gas-to-solid reactions. The apparatus includes a movable cleaning head which is configured to be substantially complementary to the interior contour of the walls of the reaction vessel. The head ejects a stream of gas with a relatively high velocity into a narrow space between the head and the walls. The head is moved substantially continuously to at least intermittently blow the stream of gas to substantially the entire surface of the walls wherein undesirable solid deposition is likely to occur. The disclosed apparatus and process is particularly useful for keeping the walls of a free-space silane-gas-to-solid-silicon reactor free of undesirable silicon deposits.

Yamakawa, K. A.↗
NASA NTRS1985

Differential wall growth in gravistimulated corn roots: Its timing and regulation

The experiments designed to document cell-wall level changes which occur as a result of their gravistimulation are described. The goal of this research is to elucidate the mechanism and time frame of differential growth following a controlled gravistimulation. To achieve this, rates of wall deposition will be determined by following the incorporation of radioactive monosaccharides into the wall. Complementing this experiment will be a freeze-etch study directed at revealing the spatial arrangment of both newly-deposited microfibrils and microfibrils that were present in the growing root prior to stimulation. The second phase of the proposed research will examine the roles ethylene and Ca(2+) have in the modulation of differential wall changes during gravitropism. Ethylene and Ca(2+) have both been implicated as regulators of the gravitropic response in roots and they have also been implicated as regulators of the gravitropic response in roots and they have also been reported to exert some control on the orientation of microfibrils. Both of these agents will be manipulated in such a way as to reveal whether they have a direct influence on cell wall deposition and microfibrillar alignment during the geotropic response.

Serlin, B. S.↗
NASA NTRS1984

Atomic hydrogen maser measurements with wall surfaces of carbon tetrafluoride

The principal objectives of the Smithsonian Astrophysical Observatory cold maser research programs are given. This work is aimed principally at understanding more about the interaction of hydrogen atoms with wall coatings of fluorinated ethylene propylene (Dupont Teflon FEP-120 co-polymer) and of carbon tetrafluoride (CE4). The principal measured quantity in these experiments is the wall shift of the maser's output frequency. The wall shift per atomic collision was calculated from the measured wall frequency shift. This assumes that the wall surface area is smooth on a molecular scale.

Vessot, R. F. C.↗
NASA NTRS1986

Wall Interference in Two-Dimensional Wind Tunnels

Viscosity and tunnel-wall constraints introduced via boundary conditions. TWINTN4 computer program developed to implement method of posttest assessment of wall interference in two-dimensional wind tunnels. Offers two methods for combining sidewall boundary-layer effects with upper and lower wall interference. In sequential procedure, Sewall method used to define flow free of sidewall effects, then assessed for upper and lower wall effects. In unified procedure, wind-tunnel flow equations altered to incorporate effects from all four walls at once. Program written in FORTRAN IV for batch execution.

Kemp, William B., Jr.↗
NASA NTRS1986

Predicting Wall Modifications for Adaptive Wind Tunnels

Wall shape changed iteratively until it matches streamlines. FLEXWAL predicts upper and lower wall modifications necessary to remove wall-interference effects in adaptive-wall wind tunnels. FLEXWAL aids in elimination of wall-interference effects on objects tested in typical two-dimensional wind tunnel with rigid sidewalls and flexible, solid floor and ceiling boundaries. Iterative procedure valid for subsonic and transonic test conditions, and convergence of method verified both analytically and experimentally. FLEXWAL written in FORTRAN IV for batch execution.

Everhart, J. L.↗
NASA NTRS1986

Estimating Wall-Induced Velocities in Wind Tunnels

Estimates of wall effects in two-dimensional wind tunnel obtained using upwash measurements on two contours near test model. Method derived from combination of prior techniques that correct for wall effects. Improved method limited to flows described by linear equations. Method accurately predicted wall-induced velocities along centerline of theoretical wind tunnel and confirmed that wall adjustments substantially reduced wall interference.

Schairer, E. T.↗
NASA NTRS1986

Wall temperature control of low-speed body drag

The use of thermal means to control drag under turbulent boundary layer conditions is examined. Numerical calculations are presented for both skin friction and (unseparated) pressure drag for turbulent boundary-layer flows over a fuselage-like body with wall heat transfer. In addition, thermal control of separation on a bluff body is investigated. It is shown that a total drag reduction of up to 20 percent can be achieved for wall heating with a wall-to-total-freestream temperature ratio of 2. For streamlined slender bodies, partial wall heating of the forebody can produce almost the same order of total drag reduction as the full body heating case. For bluff bodies, the separation delay from partial wall cooling of the afterbody is approximately the same as for the fully cooled body.

Lin, J. C.↗
NASA NTRS1986

Response of hot element wall shear stress gages in laminar oscillating flows

An experimental investigation of the time-dependent response of hot element wall shear stress gages in unsteady periodic air flows is reported. The study has focused on wall shear stress in laminar oscillating flows produced on a flat plate by a free stream velocity composed of a mean component and a superposed sinusoidal variation. Two types of hot element gages, platinum film and flush wire, were tested for values of reduced frequency ranging from 0.14 to 2.36. Values of the phase angle of the wall shear stress variation relative to the free stream velocity, as indicated by the hot element gages, are compared with numerical prediction. The comparisons show that the gages indicate a wall shear stress variation that lags the true variation, and that the gages will also not indicate the correct wall shear stress variation in periodic turbulent flows.

Cook, W. J.↗
NASA NTRS1987

Near-wall k-epsilon turbulence modeling

The flow fields from a turbulent channel simulation are used to compute the budgets for the turbulent kinetic energy (k) and its dissipation rate (epsilon). Data from boundary layer simulations are used to analyze the dependence of the eddy-viscosity damping-function on the Reynolds number and the distance from the wall. The computed budgets are used to test existing near-wall turbulence models of the k-epsilon type. It was found that the turbulent transport models should be modified in the vicinity of the wall. It was also found that existing models for the different terms in the epsilon-budget are adequate in the region from the wall, but need modification near the wall. The channel flow is computed using a k-epsilon model with an eddy-viscosity damping function from the data and no damping functions in the epsilon-equation. These computations show that the k-profile can be adequately predicted, but to correctly predict the epsilon-profile, damping functions in the epsilon-equation are needed.

Mansour, N. N.↗
NASA NTRS1986

The evolution of adaptive-wall wind tunnels

Since its inception, adaptive wall wind tunnel design has developed three major configurational possibilities: streamlined walls, variable porosity walls, and segmented plenum arrangements. All of these methods have demonstrated their feasibility for transonic flow research; development programs are noted to be underway for three-dimensional adaptive wall tunnels. With the availability of advanced computational procedures, routine angle-of-incidence or Mach sweeps may be treated numerically, while adaptive wall wind tunnels are employed for complementary point-design and for testing at flow conditions that are beyond the capabilities of current numerical modeling.

Davis, S. S.↗
NASA NTRS1987

An experimental investigation of straight and curved annular wall jets

Accurate turbulence measurements taken in wall jet flows are difficult to obtain, due to high intensity turbulence and problems in achieving two-dimensionality. The problem is compounded when streamwise curvature of the flow is introduced, since the jet entrainment and turbulence levels are greatly increased over the equivalent planar values. In this experiment, two-dimensional straight and curved incompressible wall jet flows are simulated by having a jet blow axially over a cylinder. Hot wire measurements and some Laser Doppler Velocimetry measurements are presented for straight and curved wall jet flows. The results for the straight wall showed good agreement between the annular flow data and the rectangular data taken by previous researchers. For the jets with streamwise curvature, there was agreement between the annular and corresponding rectangular jets for the flow region closest to the slot exit. An integral analysis was used as a simple technique to interpret the experimental results. Integral momentum calculations were performed for both straight and curved annular and two dimensional wall jets. The results of the calculation were used to identify transverse curvature parameters and to predict the values of those parameters which would delineate the region where the annular flow can satisfactorily simulate two dimensional flow.

Rodman, L. C.↗
NASA NTRS1988

An evaluation in a modern wind tunnel of the transonic adaptive wall adjustment strategy developed by NPL in the 1940's

The first documented wind tunnel employing a flexible walled test section for the purpose of eliminating wall interference was constructed in England by the National Physical Laboratory (NPL) during the late 1930's. The tunnel was transonic and designed for two-dimensional testing. In an attempt to eliminate the top and bottom wall interference effects on the model NPL developed a strategy to adjust two flexible walls to streamlined shapes. This report covers an evaluation of the NPL wall adjustment strategy in a modern wind tunnel, e.g., the Transonic Self-Streamlining Wind Tunnel (TSWT) at the University of Southampton, England. The evaluation took the form of performance comparisons with other modern strategies which have been developed for use in, and proven in, the TSWT.

Lewis, M. C.↗
NASA NTRS1987

Self similarity of two point correlations in wall bounded turbulent flows

The structure of turbulence at a height y from a wall is affected by the local mean shear at y, by the direct effect of the wall on the eddies, and by the action of other eddies close to or far from the wall. Some researchers believe that a single one of these mechanisms is dominant, while others believe that these effects have to be considered together. It is important to understand the relative importance of these effects in order to develop closure models, for example for the dissipation or for the Reynolds stress equation, and to understand the eddy structure of cross correlation functions and other measures. The specific objective was to examine the two point correlation, R sub vv, of the normal velocity component v near the wall in a turbulent channel flow and in a turbulent boundary layer. The preliminary results show that even in the inhomogeneous turbulent boundary layer, the two-point correlation function may have self similar forms. The results also show that the effects of shear and of blocking are equally important in the form of correlation functions for spacing normal to the wall. But for spanwise spacing, it was found that the eddy structure is quire different in these near flows. So any theory for turbulent structure must take both these effects into account.

Hunt, J. C. R.↗
NASA NTRS1988

Wind tunnel wall interference (January 1980 - May 1988): A selected, annotated bibliography

This selected bibliography lists 423 entries on the subject of wall interference during testing in wind tunnels. It is the third in a series of bibliographies on the subject. The first, NASA TM-87639, August 1986, is concerned with the reduction of wall interference by the use of adaptive walls. The second, NASA TP-89066, December 1986, is on wall interference in V/STOL and high lift testing. This, the third in the series, covers the wall interference literature published during the period January 1980 through May 1988, generally excluding those topics covered in the first two parts.

Tuttle, Marie H.↗
NASA NTRS1987

Theoretical and experimental analysis of the slotted-wall flow field in a transonic wind tunnel

The flow in the vicinity of a longitudinally slotted wind-tunnel wall is theoretically analyzed, and equations describing the pressure drop across the wall are derived. The ideal form of the slotted-wall boundary condition is shown to effectively model the wall pressure drop upstream of the point of maximum model thickness providing that a zero-shift correction to the reference pressure is included in the analysis. The wall-pressure drop equations can be linearized by subtracting the tunnel-empty boundary condition. Good correlation is obtained between experimental and theoretical values for variations in Mach number and angle of attack.

Everhart, Joel L.↗