Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VIBRATION EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Effect of Bearing Dynamic Stiffness on Gear Vibration

Noise is a major consideration in the design of high performance geared transmissions, such as for helicopters. Transmission error, that is, the accuracy with which the driven gear follows the driver gear, is a common indicator of noise generation. It is well known that bearing properties have a strong influence on shaft dynamics. However, up to now the contribution of bearings to transmission error has received little attention. In this paper, a torsional-axial-lateral geared rotor analysis is used to determine dynamic transmission error as a function of bearing stiffness and damping. Bearings have a similar effect as found in shaft dynamics; transmission error can be reduced more than 10 decibels by appropriate selection of bearing properties.

Fleming, David P.↗

A Parametric Study of Spur Gear Dynamics

A parametric study of a spur gear system was performed through a numerical analysis approach. This study used the gear dynamic program DANST, a computer simulator, to determine the dynamic behavior of a spur gear system. The analytical results have taken the deflection of shafts and bearings into consideration for static analysis, and the influence of these deflections on gear dynamics was investigated. Damping in the gear system usually is an unknown quantity, but it has an important effect in resonance vibration. Typical values as reported in the literature were used in the present analysis. The dynamic response due to different damping factors was evaluated and compared. The effect of the contact ratio on spur gear dynamic load and dynamic stress was investigated through a parameter study. The contact ratio was varied over the range of 1.26 to 2.46 by adjusting the tooth addendum. Gears with contact ratio near 2.0 were found to have the most favorable dynamic performance.

Lin, Hsiang Hsi↗

Oriented single-crystal nuclear resonance vibrational spectroscopy of [Fe(TPP)(MI)(NO)] : quantitative sssessment of the trans effect of NO.

This paper presents oriented single-crystal Nuclear Resonance Vibrational Spectroscopy (NRVS) data for the six-coordinate (6C) ferrous heme-nitrosyl model complex [{sup 57}Fe(TPP)(MI)(NO)] (1; TPP{sup 2-} = tetraphenylporphyrin dianion; MI = 1-methylimidazole). The availability of these data enables for the first time the detailed simulation of the complete NRVS data, including the porphyrin-based vibrations, of a 6C ferrous heme-nitrosyl, using our quantum chemistry centered normal coordinate analysis (QCC-NCA). Importantly, the Fe-NO stretch is split by interaction with a porphyrin-based vibration into two features, observed at 437 and 472 cm{sup -1}. The 437 cm{sup -1} feature is strongly out-of-plane (oop) polarized and shows a {sup 15}N{sup 18}O isotope shift of 8 cm{sup -1} and is therefore assigned to v(Fe-NO). The admixture of Fe-N-O bending character is small. Main contributions to the Fe-N-O bend are observed in the 520-580 cm{sup -1} region, distributed over a number of in-plane (ip) polarized porphyrin-based vibrations. The main component, assigned to {delta}{sub ip}(Fe-N-O), is identified with the feature at 563 cm{sup -1}. The Fe-N-O bend also shows strong mixing with the Fe-NO stretching internal coordinate, as evidenced by the oop NRVS intensity in the 520-580 cm{sup -1} region. Very accurate normal mode descriptions of ?(Fe-NO) and {delta}{sub ip}(Fe-N-O) have been obtained in this study. These results contradict previous interpretations of the vibrational spectra of 6C ferrous heme-nitrosyls where the higher energy feature at {approx}550 cm{sup -1} had usually been associated with v(Fe-NO). Furthermore, these results provide key insight into NO binding to ferrous heme active sites in globins and other heme proteins, in particular with respect to (a) the effect of hydrogen bonding to the coordinated NO and (b) changes in heme dynamics upon NO coordination. [Fe(TPP)(MI)(NO)] constitutes an excellent model system for ferrous NO adducts of myoglobin (Mb) mutants where the distal histidine (His64) has been removed. Comparison to the reported vibrational data for wild-type (wt) Mb-NO then shows that the effect of H bonding to the coordinated NO is weak and mostly leads to a polarization of the {pi}/{pi}* orbitals of bound NO. In addition, the observation that {delta}{sub ip}(Fe-N-O) does not correlate well with ?(N-O) can be traced back to the very mixed nature of this mode. The Fe-N(imidazole) stretching frequency is observed at 149 cm{sup -1} in [Fe(TPP)(MI)(NO)], and spectral changes upon NO binding to five-coordinate ferrous heme active sites are discussed. The obtained high-quality force constants for the Fe-NO and N-O bonds of 2.57 and 11.55 mdyn/{angstrom} can further be compared to those of corresponding 5C species, which allows for a quantitative analysis of the {sigma} trans interaction between the proximal imidazole (His) ligand and NO. This is key for the activation of the NO sensor soluble guanylate cyclase. Finally, DFT methods are calibrated against the experimentally determined vibrational properties of the Fe-N-O subunit in 1. DFT is in fact incapable of reproducing the vibrational energies and normal mode descriptions of the Fe-N-O unit well, and thus, DFT-based predictions of changes in vibrational properties upon heme modification or other perturbations of these 6C complexes have to be treated with caution.

08 HYDROGEN↗

A rigorous full-dimensional quantum dynamics study of tunneling splitting of rovibrational states of vinyl radical C 2 H 3

Here, we report a rigorous quantum mechanical study of the rovibrational energy levels of vinyl radical C 2 H 3 . The calculations are carried out using a real two-component multi-layer Lanczos algorithm in a set of orthogonal polyspherical coordinates based on a recently developed accurate ab initio potential energy surface of C 2 H 3 . All well converged 158 vibrational bands up to 3200 cm -1 are determined, together with a comparison to previous calculations and experimental results. Our results show a remarkable multi-dimensional tunneling effect on the vibrational spectra of the radical. The vibrational tunneling splitting is substantially different from that of previous reduced dimensional calculations. The rotational constants of the fundamental vibrational bands of C 2 H 3 are also given. It was found that the rovibrational states are strongly coupled, especially among those bending vibrational modes. Additionally, the perturbative iteration approach of Gruebele has been extended to assign the rovibrational energy levels of C 2 H 3 without the requirement of explicit wavefunctions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Single-molecule electronics: Cooling individual vibrational modes by the tunneling current

Electronic devices composed of single molecules constitute the ultimate limit in the continued downscaling of electronic components. A key challenge for single-molecule electronics is to control the temperature of these junctions. Controlling heating and cooling effects in individual vibrational modes can, in principle, be utilized to increase stability of single-molecule junctions under bias, to pump energy into particular vibrational modes to perform current-induced reactions, or to increase the resolution in inelastic electron tunneling spectroscopy by controlling the life-times of phonons in a molecule by suppressing absorption and external dissipation processes. Under bias the current and the molecule exchange energy, which typically results in heating of the molecule. However, the opposite process is also possible, where energy is extracted from the molecule by the tunneling current. Designing a molecular “heat sink” where a particular vibrational mode funnels heat out of the molecule and into the leads would be very desirable. It is even possible to imagine how the vibrational energy of the other vibrational modes could be funneled into the “cooling mode,” given the right molecular design. Previous efforts to understand heating and cooling mechanisms in single molecule junctions have primarily been concerned with small models, where it is unclear which molecular systems they correspond to. In this paper, our focus is on suppressing heating and obtaining current-induced cooling in certain vibrational modes. Strategies for cooling vibrational modes in single-molecule junctions are presented, together with atomistic calculations based on those strategies. Cooling and reduced heating are observed for two different cooling schemes in calculations of atomistic single-molecule junctions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Vibrational Energy Harvesting Sensor Based on Linear and Rotational Electromechanical Effects

In this investigation, a magnetically coupled double-spring design is presented for harvesting low-level non-stationary random vibrational energy. The sensor relies on multimodal coupling between the translation and rotation of a two-spring magnet and coil system to widen the harvesting bandwidth. Energy methods are used to develop a model to characterize the electromechanical response of the system, the solution of which is obtained using stochastic techniques based on a particle swarm algorithm. This approach provides an efficient method to estimate system parameters that otherwise are difficult or impossible to determine with independent measurements. The experimental results demonstrate agreement with the theoretical predictions over a limited bandwidth. The sensor can effectively harvest non-stationary vibration energy down to 10 -4 g within a limited bandwidth of 130–150 Hz. The sensor prototype has an operational volume of 2.6 cm 3 with a calculated power density of 0.2 W/cm 3 . The sensor’s small size results in a coupling efficiency of approximately 6% across the tested bandwidth.

42 ENGINEERING↗

Coherent electronic-vibrational dynamics in deuterium bromide probed via attosecond transient-absorption spectroscopy

Ultrafast laser excitation can trigger multiplex coherent dynamics in molecules. Here, we report attosecond transient-absorption experiments addressing simultaneous probing of electronic and vibrational dynamics in a prototype molecule, deuterium bromide (DBr), following its strong-field ionization. Electronic and vibrational coherences in the ionic X$^2\Pi_{3/2}$ and X$^2\Pi_{1/2}$ states are characterized in the Br-$3d$ core-level absorption spectra via quantum beats with 12.6-fs and 19.9-fs periodicities, respectively. Polarization scans reveal that the phase of the electronic quantum beats depends on the probe direction, experimentally showing that the coherent electronic motion corresponds to the oscillation of the hole density along the ionization-field direction. The vibrational quantum beats are found to maintain a relatively constant amplitude, whereas the electronic quantum beats exhibit a partial decrease in time. Quantum wave-packet simulations show that the decoherence effect from the vibrational motion is insignificant because of the parallel relation between the X$^2\Pi_{3/2}$ and X$^2\Pi_{1/2}$ potentials. Finally, a comparison between the DBr and HBr results suggests that rotation motion is responsible for the decoherence since it leads to initial alignment prepared by the strong-field ionization.

74 ATOMIC AND MOLECULAR PHYSICS↗

N 2 vibrational excitation in atmospheric pressure ns pulse and RF plasma jets

Time-resolved N 2 vibrational temperature and translational–rotational temperature in quasi-two-dimensional atmospheric pressure plasma jets sustained by ns pulse and RF discharges in nitrogen/noble gas mixtures are measured by the broadband vibrational Coherent Anti-Stokes Raman Scattering (CARS) . The results indicate a much stronger vibrational excitation in the RF plasma jet, due to the lower reduced electric field and higher discharge power. In a ns pulse discharge in N 2 /He, N 2 vibrational temperature is significantly lower compared to that in N 2 /Ar, due to the more rapid vibration–translation (V–T) relaxation of nitrogen by helium atoms. In the RF plasma jets in N 2 /Ne and N 2 /Ar, the vibrational excitation increases considerably as the nitrogen fraction in the mixture is reduced. The experimental data in the RF plasma jet in N 2 /Ar jet are compared with the kinetic modeling predictions. The results indicate that nitrogen vibrational excitation in N 2 /Ar plasma jets with a small N 2 fraction in the mixture (several percent) is controlled primarily by electron impact, anharmonic vibration–vibration (V–V) pumping, and V–T relaxation by N atoms. In comparison, V–V energy transfer from the vibrationally excited molecules in the first excited electronic state, N 2 (A 3 Σ u + , v), which are generated primarily by the energy transfer from the metastable Ar atoms, has a minor effect on the vibrational populations of the ground electronic state, N 2 (X 1 Σ g + , v). Although the discharge energy fraction going to electronic excitation is significant, the predicted quasi-steady-state N 2 (A 3 Σ u + ) number density, controlled by the energy pooling and quenching by N atoms, remains relatively low. Because of this, the net rate of N 2 (X 1 Σ g + ) vibrational excitation by the V–V energy transfer from N 2 (A 3 Σ u + ) is much lower compared to that by the direct electron impact. Furthermore, the results show that atmospheric pressure RF plasma jets can be used as sources of highly vibrationally excited N 2 molecules and N atoms.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Coupling between plate vibration and acoustic radiation

A detailed numerical investigation of the coupling between the vibration of a flexible plate and the acoustic radiation is performed. The nonlinear Euler equations are used to describe the acoustic fluid while the nonlinear plate equation is used to describe the plate vibration. Linear, nonlinear, and quasi-periodic or chaotic vibrations and the resultant acoustic radiation are analyzed. We find that for the linear plate response, acoustic coupling is negligible. However, for the nonlinear and chaotic responses, acoustic coupling has a significant effect on the vibration level as the loading increases. The radiated pressure from a plate undergoing nonlinear or chaotic vibrations is found to propagate nonlinearly into the far-field. However, the nonlinearity due to wave propagation is much weaker than that due to the plate vibrations. As the acoustic wave propagates into the far-field, the relative difference in level between the fundamental and its harmonics and subharmonics decreases with distance.

Frendi, Abdelkader↗

Coupling between plate vibration and acoustic radiation

A detailed numerical investigation of the coupling between the vibration of a flexible plate and the acoustic radiation is performed. The nonlinear Euler equations are used to describe the acoustic fluid while the nonlinear plate equation is used to describe the plate vibration. Linear, nonlinear, and quasi-periodic or chaotic vibrations and the resultant acoustic radiation are analyzed. We find that for the linear plate response, acoustic coupling is negligible. However, for the nonlinear and chaotic responses, acoustic coupling has a significant effect on the vibration level as the loading increases. The radiated pressure from a plate undergoing nonlinear or chaotic vibrations is found to propagate nonlinearly into the far field. However, the nonlinearity due to wave propagation is much weaker than that due to the plate vibrations. As the acoustic wave propagates into the far field, the relative difference in level between the fundamental and its harmonics and subharmonics decreases with distance.

Frendi, Abdelkader↗

Effective theory of superconductivity in strongly coupled amorphous materials

A theory of phonon-mediated superconductivity in strong-coupling amorphous materials is developed based on an effective description of structural disorder and its effect on the vibrational spectrum. The theory accounts for the diffusivelike transport of vibrational excitations due to disorder-induced scattering within the Eliashberg theory of strong-coupling superconductivity. The theory provides a good analytical description of the Eliashberg function $α^2F(ω)$ in comparison with experiments and allows one to disentangle the effects of transverse and longitudinal excitations on the Eliashberg function. In particular, it shows that the transverse excitations play a crucial role in driving an increase or excess in the Eliashberg function at low energy, which is related to the boson peak phenomenon in vibrational spectra of glasses. This low-energy excess, on the one hand, drives an enhancement of the electron-phonon coupling but at the same time reduces the characteristic energy scale $ω_{\text{log}}$ in the Allen-Dynes formula. As a consequence, the nonmonotonicity of $T_c$ as a function of alloying (disorder) in Pb-based systems can be rationalized. Further, the case of Al-based systems, where disorder increases $T_c$ from the start, is also analyzed. General material-design principles for enhancing $T_c$ in amorphous superconductors are presented.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ammonia generation in Ns pulse and Ns pulse/RF discharges over a catalytic surface

Plasma-catalytic ammonia synthesis in a ns pulse discharge and a 'hybrid' ns pulse/RF discharge in plane-to-plane geometry is studied by Fourier Transform infrared absorption spectroscopy. The data are taken in a preheated H 2 –N 2 mixture, with and without Ni/γ-Al 2 O 3 or Co/γ-Al 2 O 3 catalyst placed in the discharge section. The measurement results are taken using two different approaches. The first is a 'single-stage' process, where a ns pulse discharge in the H 2 –N 2 mixture is sustained continuously. In this case, the ammonia yield increases slowly, over a period of tens of minutes. The second is a 'two-stage' process, where the catalyst is first activated by the ns pulse discharge sustained in pure nitrogen, and then the activated catalyst is exposed to the H 2 –N 2 flow, with or without the discharge. In this case, a strong overshoot of the NH 3 number density at the reactor exit is detected, by over a factor of two compared to the single-stage process. After the initial overshoot, the ammonia yield gradually decreases to the 'single stage' value (with the discharge on), or to near zero (with the discharge off). The results demonstrate that the ammonia yield in the plasma-catalytic reactor is controlled by the N atom accumulation on the catalyst surface, which reacts with H atoms thermally dissociated on the catalyst or generated in the plasma. The results also show that the plasma-catalytic ammonia yield is significantly higher compared to that in the ns pulse discharge without the catalyst. The accumulation of H atoms on the catalyst, with their subsequent reactions with N atoms generated in the plasma, is of relatively minor importance at the present conditions. An additional series of measurements was made with a sub-breakdown RF waveform overlapped with the ns pulse discharge train, to enhance the vibrational excitation of nitrogen. The ammonia yield measured with the RF waveform added is approximately 20% higher compared to that at the baseline ns pulse discharge conditions, both with and without the catalyst. This effect is weaker compared to that of the catalyst activation by N atoms. Additional data are necessary to isolate the possible effect of the vibrationally excited N 2 molecules on the ammonia synthesis in the plasma catalytic reactions.

surface reactions↗

Determination of the N2 recombination rate coefficient in the ionosphere

Measurements of aeronomic parameters made by the Atmosphere Explorer-C satellite are used to determine the recombination rate coefficient of N2(+) in the ionosphere. The rate is found to increase significantly with decreasing electron density. Values obtained range from approximately 1.4 x 10 to the -7th to 3.8 x 10 to the -7th cu cm/sec. This variation is explained in a preliminary way in terms of an increase in the rate coefficient with vibrational excitation. Thus, high electron densities depopulate high vibrational levels reducing the effective recombination rate, whereas, low electron densities result in an enhancement in the population of high vibrational levels, thus, increasing the effective recombination rate.

Orsini, N.↗

Excited collective states of heavy even-even nuclei

Quadrupole-type collective excitations of even-even nuclei are analyzed. In this analysis, transverse {gamma} vibrations of the nuclear surface are taken into account effectively, while longitudinal beta vibrations remain free. A potential energy of the exponential form is used for free surface longitudinal beta vibrations. The behavior of the energy levels of excited states in the ground-state, {beta}, and {gamma} bands of heavy nuclei is studied, and the predictive potential of the model used is demonstrated for transfermium nuclei.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Dual clearance squeeze film damper for high load conditions

Squeeze film dampers are widely used to control vibrations in aircraft turbine engines and other rotating machinery. However, if shaft unbalance rises appreciably above the design value (e.g., due to a turbine blade loss), a conventional squeeze film becomes overloaded, and is no longer effective in controlling vibration amplitudes and bearing forces. A damper concept characterized by two oil films is described. Under normal conditions, only one low-clearance film is active, allowing precise location of the shaft centerline. Under high unbalance conditions, both films are active, controlling shaft vibration in a near-optimum manner, and allowing continued operation until a safe shutdown can be made.

Fleming, D. P.↗

Dual clearance squeeze film damper for high load conditions

Squeeze film dampers are widely used to control vibrations in aircraft turbine engines and other rotating machinery. However, if shaft unbalance rises appreciably above the design value (e.g., due to a turbine blade loss), a conventional squeeze film becomes overloaded, and is no longer effective in controlling vibration amplitudes and bearing forces. A damper concept characterized by two oil films is described. Under normal conditions, only one low-clearance film is active, allowing precise location of the shaft centerline. Under high unbalance conditions, both films are active, controlling shaft vibration in a near-optimum manner, and allowing continued operation until a safe shutdown can be made.

Fleming, D. P.↗