Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SIDE EFFECTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Experimental aerodynamic characteristics for a cylindrical body of revolution with side strakes and various noses at angles of attack from 0 degrees to 58 degrees and Mach numbers from 0.6 to 2.0

For a body of revolution with afterbody side strakes, an experimental investigation was conducted in the Ames 6- by 6-Foot Wind Tunnel to determine the effects on the aerodynamic characteristics of forebody geometry, nose strakes, body side strakes, Reynolds number, Mach number, and angle of attack. Aerodynamic force and moment characteristics were measured for the straked cylindrical afterbody (cylinder fineness ratio of 7) with tangent ogive noses of fineness ratio 2.5 to 5.0. In addition, the straked cylinder afterbody was tested with an ogive nose having a rounded tip and an ogive nose with two different nose strake arrangements. The data demonstrate that the aerodynamic characteristics for a body of revolution with side strakes can be significantly affected by changes in nose fineness ratio, nose bluntness, Reynolds number, Mach number, and, of course, angle of attack. Removing the strakes from the cylindrical aftersection greatly decreased the lift, but this removal hardly changed the maximum magnitudes of the undesirable side forces that developed at angles of attack greater than about 25 deg for subsonic Mach numbers.

Jorgensen, L. H.↗
DOE OSTI2021

Enhanced anomalous Nernst effect in disordered Dirac and Weyl materials

Here, we analyze the thermoelectric response of Dirac and Weyl semimetals using the semiclassical approach, focusing on the extrinsic contributions due to skew-scattering and side jump. Our results apply to the linear response Nernst effect in ferromagnetic Dirac materials such as Fe 3 Sn 2 and Weyl semimetals like Co 3 Sn 2 S 2 . In the case of Fe 3 Sn 2 we obtain a very good agreement with known experimental anomalous Hall effect measurements, and based on that we predict a large Nernst effect in this material.We also extend the investigation to second-order response, focusing on monolayer graphene on hBN with trigonal warping as an example. Our analysis indicates that the extrinsic contributions can be a significant component of anomalous Nernst response and may be used to explain an enhanced thermoelectric response.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Theoretical and experimental constraints for the equation of state of dense and hot matter

Abstract This review aims at providing an extensive discussion of modern constraints relevant for dense and hot strongly interacting matter. It includes theoretical first-principle results from lattice and perturbative QCD, as well as chiral effective field theory results. From the experimental side, it includes heavy-ion collision and low-energy nuclear physics results, as well as observations from neutron stars and their mergers. The validity of different constraints, concerning specific conditions and ranges of applicability, is also provided.

Kumar, Rajesh (ORCID:0000000327463956)↗
DOE OSTI2021

Understanding the Mesoscale Degradation in Nickel-Rich Cathode Materials through Machine-Learning-Revealed Strain–Redox Decoupling

The degradation of nickel-rich cathode materials for lithium-ion batteries upon prolonged electrochemical cycling features a complicated interplay among electronic structure, lattice configuration, and micro-morphology. The underlying mechanism for such an entanglement of different material properties at nano- to mesoscales is fundamental to the battery performance but not well-understood yet. Here we investigate the correlation between the local redox reaction and lattice mismatch through a nano-resolution synchrotron spectro-microscopy study of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM 811) cathode particles. With assistance from a machine-learning-based data classification method, we identify local regions that demonstrate a strain–redox decoupling effect, which can be attributed to different side reactions. Overall, our results highlight the mesoscale reaction heterogeneity in the battery cathode and suggest that particle structure engineering could be a viable approach to mitigate the chemomechanical degradation of cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2023

Enabling selective zinc-ion intercalation by a eutectic electrolyte for practical anodeless zinc batteries

Abstract Two major challenges hinder the advance of aqueous zinc metal batteries for sustainable stationary storage: (1) achieving predominant Zn-ion (de)intercalation at the oxide cathode by suppressing adventitious proton co-intercalation and dissolution, and (2) simultaneously overcoming Zn dendrite growth at the anode that triggers parasitic electrolyte reactions. Here, we reveal the competition between Zn 2+ vs proton intercalation chemistry of a typical oxide cathode using ex-situ/ operando techniques, and alleviate side reactions by developing a cost-effective and non-flammable hybrid eutectic electrolyte. A fully hydrated Zn 2+ solvation structure facilitates fast charge transfer at the solid/electrolyte interface, enabling dendrite-free Zn plating/stripping with a remarkably high average coulombic efficiency of 99.8% at commercially relevant areal capacities of 4 mAh cm −2 and function up to 1600 h at 8 mAh cm −2 . By concurrently stabilizing Zn redox at both electrodes, we achieve a new benchmark in Zn-ion battery performance of 4 mAh cm −2 anode-free cells that retain 85% capacity over 100 cycles at 25 °C. Using this eutectic-design electrolyte, Zn | |Iodine full cells are further realized with 86% capacity retention over 2500 cycles. The approach represents a new avenue for long-duration energy storage.

25 ENERGY STORAGE↗
DOE OSTI2023

Improved wall-plug efficiency of III-nitride tunnel junction micro-light-emitting diodes with AlGaN/GaN polarization charges

The electrical performances of III-nitride blue micro-light-emitting diodes (µLEDs) with different tunnel junction (TJ) epitaxial architectures grown by metalorganic chemical vapor deposition are investigated. A new TJ structure that employs AlGaN is introduced. The current density–voltage characteristic is improved by incorporating AlGaN layer above the n-side of the TJ layer, and the effects of the AlGaN/GaN superlattices is examined. Based upon the data from band diagram simulation, net positive polarization charge is formed at the AlGaN/GaN interface, which results in a reduction in tunneling distance and increase in tunneling probability. Moreover, similar electrical improvement is observed in various device dimensions and is independent of operating current density, suggesting that AlGaN/GaN biaxial tensile strain or current spreading is not the main contribution for the improvement. Finally, the effects on the efficiency performances are determined. While the maximum external quantum efficiency of the TJ devices remains identical, the wall-plug efficiency of µLEDs is enhanced significantly by the proposed AlGaN-enhanced TJ design. This work reveals the possibility of energy efficient TJ contact with high transparency in the visible wavelength range.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of 128 × 128 MM-PAD-2.1 ASIC: a fast framing hard x-ray detector with high dynamic range

Here, we characterize a new x-ray Mixed-Mode Pixel Array Detector (MM-PAD-2.1) Application Specific Integrated Circuit (ASIC). Using an integrating pixel front-end with dynamic charge removal architecture, the MM-PAD-2.1 ASIC extends the maximum measurable x-ray signal (in 20 keV photon units) to > 10 7 x-rays/pixel/frame while maintaining a low read noise across the full dynamic range, all while imaging continuously at a frame rate of up to 10 kHz. The in-pixel dynamic charge removal mechanism prevents saturation of the input amplifier and proceeds in parallel with signal integration to achieve deadtime-less measurements with incident x-ray rates of > 10 10 x-rays/pixel/s. The ASIC format consists of 128 × 128 square pixels each 150 μm on a side and is designed to be 3-side buttable so large arrays can be effectively tiled. Here we use both laboratory x-ray sources and the Cornell High Energy Synchrotron Source (CHESS) to characterize two single ASIC prototype detectors for both low (single x-ray) and high incident flux detection. In the first detector the ASIC was solder bump-bonded to a 500 μm thick Si sensor for efficient detection of x-rays below 20 keV, whereas the second detector used a 750 μm thick CdTe sensor for x-rays above ~20 keV.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Adaptive Internal Model Based Current Control with Embedded Active Damping of a Three-Phase Grid-Connected Inverter with LCL Filter for PV Application

This paper presents an internal model based controller with embedded active damping for a three-phase grid-connected inverter with LCL filter. A strategy to control the grid current based on the internal model principle is presented in this paper. It is known that a third-order LCL filter apart from providing better attenuation also poses the problem of initiating unwanted resonance oscillations especially during transients. To address this problem, an active damping strategy based on virtual resistance emulation on the grid side filter is implemented. Also, to ensure effective active damping, an online parameter update strategy is implemented for the filter parameters. The proposed method provides better attenuation to oscillation damping and achieves good tracking performance without adversely affecting the bandwidth. The architecture is verified based on computer simulations via MATLAB/Simulink and PLECS domain and various important case study results are presented.

grid-connected inverter↗
DOE OSTI2021

Carbon and Hydrocarbon Particle Seeding in Air-Breathing Rotating Detonation Engine

Within the power generation community, the rotating detonation engine (RDE) is only growing in popularity with its increased performance, simple mechanism, and operation. Although significant testing is underway to characterize the RDE for integration with conventional gas turbines, this entire system is still at a relatively low technology readiness level. In the midst of RDE research, there is an initiative to understand solid particle seeding effects in the detonation performance. Under investigation at the University of Central Florida is a Department of Energy (DOE) 15.24 cm (6 in.) RDE, with a solid particle seeder in parallel with its H2 and air flow lines. Previous work on this system involved carbon particle detonation; however, the tested particles were taken one step further to include more sustainable, greener hydrocarbon particles. Testing of powdered sugar, peanut flour, and cornstarch, along with previous carbon black tests have shown not only successful detonability, but a noticeable effect on the detonation wave dynamics. Side-by-side with a particle burning model being developed, an operational map can be determined for the hydrocarbon particles particularly, which can be tuned with the local flow conditions to achieve peak operability while replacing fuels with sustainable alternatives that could even be grown.

Engineering↗
DOE OSTI2022

TiNi-Based Bi-Metallic Shape-Memory Alloy by Laser-Directed Energy Deposition

In this study, laser-directed energy deposition was applied to build a Ti-rich ternary Ti–Ni–Cu shape-memory alloy onto a TiNi shape-memory alloy substrate to realize the joining of the multifunctional bi-metallic shape-memory alloy structure. The cost-effective Ti, Ni, and Cu elemental powder blend was used for raw materials. Various material characterization approaches were applied to reveal different material properties in two sections. The as-fabricated Ti–Ni–Cu alloy microstructure has the TiNi phase as the matrix with Ti2Ni secondary precipitates. The hardness shows no high values indicating that the major phase is not hard intermetallics. A bonding strength of 569.1 MPa was obtained by tensile testing, and digital image correlation reveals the different tensile responses of the two sections. Differential scanning calorimetry was used to measure the phase-transformation temperatures. The austenite finishing temperature of higher than 80 °C was measured for the Ti–Ni–Cu alloy section. For the TiNi substrate, the austenite finishing temperature was tested to be near 47 °C at the bottom and around 22 °C at the upper substrate region, which is due to the repeated laser scanning that acts as annealing on the substrate. Finally, the multiple shape-memory effect of two shape-memory alloy sides was tested and identified.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Improvements in the slotted-wall boundary condition

It is shown that the form of the slotted wind tunnel wall boundary condition can be obtained directly from the ideal slot conditions without specification of the cross-sectional geometry of the slot. The treatment of flat slots is generalized so that configurations with sidewalls in the plenum can be treated. It is shown that these variations do not change the slotted-wall boundary condition significantly. It is concluded that the effects of slot sidewalls and separation in the plenum on the coefficient of the slotted-wall boundary condition are small compared to the effect of the slat on the tunnel side.

Barnwell, R. W.↗
NASA NTRS1976

Specification of pyro shock tests

Specifications of pyro shock tests are treated as the interconnection between raw measurements (or estimates) of the environment and the various test methods available. After a definition of the environment, various aspects of test method specification are discussed including one-sided pulses, test simulation parameters, and the effects of Q. Different test configurations are considered including rigid fixture tests, pseudo-real structure, and real structure.

Trummel, M.↗
NASA NTRS1976

Upper-surface-blowing flow-turning performance

Jet exhaust flow-turning characteristics were determined for systematic variations in upper-surface blowing exhaust nozzles and trailing-edge flap configuration variables from experimental wind-off (static) flow studies. For conditions with parallel flow exhausting from the nozzle, jet height (as indicated by nozzle exit height) and flap radius were found to be the most important parameters relating to flow turning. Nonparallel flow from the nozzle, as obtained from an internal roof angle and/or side spread angle, had a large favorable effect on flow turning. Comparisons made between static turning results and wind tunnel aerodynamic studies of identical configurations indicated that static flow-turning results can be indicative of wind-on powered lift performance for both good and poor nozzle-flap combinations but, for marginal designs, can lead to overly optimistic assessment of powered lift potential.

Sleeman, W. C., Jr.↗
NASA NTRS1985

Investigation of flowfields found in typical combustor geometries

Activities undertaken during the entire course of research are summarized. Studies were concerned with experimental and theoretical research on 2-D axisymmetric geometries under low speed nonreacting, turbulent, swirling flow conditions typical of gas turbine and ramjet combustion chambers. They included recirculation zone characterization, time-mean and turbulence simulation in swirling recirculating flow, sudden and gradual expansion flowfields, and furher complexities and parameter influences. The study included the investigation of: a complete range of swirl strengths; swirler performance; downstream contraction nozzle sizes and locations; expansion ratios; and inlet side-wall angles. Their individual and combined effects on the test section flowfield were observed, measured and characterized. Experimental methods included flow visualization (with smoke and neutrally-buoyant helium-filled soap bubbles), five-hole pitot probe time-mean velocity field measurements, and single-, double-, and triple-wire hot-wire anemometry measurements of time-mean velocities, normal and shear Reynolds sresses. Computational methods included development of the STARPIC code from the primitive-variable TEACH computer code, and its use in flowfield prediction and turbulence model development.

Lilley, D. G.↗
NASA NTRS1985

Structural Development and Gravity

Major research projects designed to elucidate the mechanisms by which gravity loading and/or fluid distribution alter bone formation and/or resorption in rat bone are reported. Projects completed include: (1) analysis of bone parameters in rats from 6 weeks to 68 weeks of age; (2) restricted access area in which rats on the model were not allowed to touch any side of the cage; and (3) the effect of dietary calcium levels on bone formation and resorption rates in controls and head-down rats.

Holton, E. M.↗
NASA NTRS1988

Analysis of coupled cylindrical striplines filled with multilayered dielectrics

A method of analysis for coupled cylindrical striplines filled with multilayered dielectrics is presented that uses a variational technique in the space domain. Coupled-mode analysis is presented for the case of a pair of coupled circular arc strips arbitrarily located between cylindrical ground planes filled with multilayered dielectrics. An even- and odd-mode approach is used for the analysis of shielded cylindrically curved edge-coupled pairs of broad-side parallel strips (broad-side, edge-coupled cylindrical striplines). The effect of environmental changes on an otherwise planar structure is also studied by extending the present analysis to cylindrically warped coupled striplines.

Reddy, C. Jagadeswara↗
NASA NTRS1990

Reducing Aerodynamic Drag Of Bluff Bodies

New method found to reduce aerodynamic drag of noncircular bluff bodies like road-transport vehicles. Consists of installation of thin, flat panels on forward side of body, facing airstream. Produces streamlining effect over body. Width of wake reduced, and vortex shedding is greatly suppressed.

Taylor, Lawrence W., Jr.↗