Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Porous flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Stabilization Mechanisms and Burning Rates of Cylindrical Burner Flames

A study is conducted of the structure and response of curved (but unstretched), cylindrically-symmetric 1D premixed flames from a cylindrical porous burner. The study has employed (1) activation-energy asymptotics with one-step reaction constant and constant properties; (2) a numerical computation which encompassed detailed chemistry and transport behavior, and (3) drop-tower microgravity tests. Attention was given to the relative importance of heat loss vs. flow divergence as the dominant mechanism for flame stabilization; the results show that, with increasing flow discharge rate, the dominant flame stabilization mechanism changes from heat loss to flow divergence.

Eng, J. A.↗
NASA NTRS2002

Advanced Nacelle Acoustic Lining Concepts Development

The work reported in this document consisted of six distinct liner technology development subtasks: 1) Analysis of Model Scale ADP Fan Duct Lining Data (Boeing): An evaluation of an AST Milestone experiment to demonstrate 1995 liner technology superiority relative to that of 1992 was performed on 1:5.9 scale model fan rig (Advanced Ducted Propeller) test data acquired in the NASA Glenn 9 x 15 foot wind tunnel. The goal of 50% improvement was deemed satisfied. 2) Bias Flow Liner Investigation (Boeing, VCES): The ability to control liner impedance by low velocity bias flow through liner was demonstrated. An impedance prediction model to include bias flow was developed. 3) Grazing Flow Impedance Testing (Boeing): Grazing flow impedance tests were conducted for comparison with results achieved at four different laboratories. 4) Micro-Perforate Acoustic Liner Technology (BFG, HAE, NG): Proof of concept testing of a "linear liner." 5) Extended Reaction Liners (Boeing, NG): Bandwidth improvements for non-locally reacting liner were investigated with porous honeycomb core test liners. 6) Development of a Hybrid Active/Passive Lining Concept (HAE): Synergism between active and passive attenuation of noise radiated by a model inlet was demonstrated.

Bielak, G.↗
NASA NTRS2003

Accomplishments of the Abrupt Wing Stall (AWS) Program and Future Research Requirements

The Abrupt Wing Stall (AWS) Program has addressed the problem of uncommanded lateral motions, such as wing drop and wing rock, at transonic speeds. The genesis of this Program was the experience of the F/A-1 8E/F Program in the late 1990's, when wing drop was discovered in the heart of the maneuver envelope for the pre-production aircraft. While the F/A-1 8E/F problem was subsequently corrected by a leading-edge flap scheduling change and the addition of a porous door to the wing fold fairing, the AWS Program was initiated as a national response to the lack of technology readiness available at the time of the F/A-18E/F Development Program. The AWS Program objectives were to define causal factors for the F/A-18E/F experience, to gain insights into the flow physics associated with wing drop, and to develop methods and analytical tools so that future programs could identify this type of problem before going to flight test. The paper reviews, for the major goals of the AWS Program, the status of the technology before the

Hall, Robert M.↗
NASA NTRS2003

Accomplishments of the Abrupt Wing Stall (AWS) Program and Future Research Requirements

The Abrupt Wing Stall (AWS) Program has addressed the problem of uncommanded lateral motions, such as wing drop and wing rock, at transonic speeds. The genesis of this Program was the experience of the F/A-18E/F Program in the late 199O's, when wing drop was discovered in the heart of the maneuver envelope for the pre-production aircraft. While the F/A-18E/F problem was subsequently corrected by a leading-edge flap scheduling change and the addition of a porous door to the wing fold fairing, the AWS Program was initiated as a national response to the lack of technology readiness available at the time of the F/A-18E/F Development Program. The AWS Program objectives were to define causal factors for the F/A-18E/F experience, to gain insights into the flow physics associated with wing drop, and to develop methods and analytical tools so that future programs could identify this type of problem before going to flight test. The paper reviews, for the major goals of the AWS Program, the status of the technology before the program began, the program objectives, accomplishments, and impacts. Lessons learned are presented for the benefit of future programs that must assess whether a vehicle will have uncommanded lateral motions before going to flight test. Finally, recommended future research needs are presented in light of the AWS Program experience.

Hall, Robert M.↗
NASA NTRS1999

Evaporative Cooling Membrane Device

An evaporative cooling membrane device is disclosed having a flat or pleated plate housing with an enclosed bottom and an exposed top that is covered with at least one sheet of hydrophobic porous material having a thin thickness so as to serve as a membrane. The hydrophobic porous material has pores with predetermined dimensions so as to resist any fluid in its liquid state from passing therethrough but to allow passage of the fluid in its vapor state, thereby, causing the evaporation of the fluid and the cooling of the remaining fluid. The fluid has a predetermined flow rate. The evaporative cooling membrane device has a channel which is sized in cooperation with the predetermined flow rate of the fluid so as to produce laminar flow therein. The evaporative cooling membrane device provides for the convenient control of the evaporation rates of the circulating fluid by adjusting the flow rates of the laminar flowing fluid.

Lomax, Curtis↗
NASA NTRS2016

Experimental Evaluation of Equivalent-Fluid Models for Melamine Foam

Melamine foam is a soft porous material commonly used in noise control applications. Many models exist to represent porous materials at various levels of fidelity. This work focuses on rigid frame equivalent fluid models, which represent the foam as a fluid with a complex speed of sound and density. There are several empirical models available to determine these frequency dependent parameters based on an estimate of the material flow resistivity. Alternatively, these properties can be experimentally educed using an impedance tube setup. Since vibroacoustic models are generally sensitive to these properties, this paper assesses the accuracy of several empirical models relative to impedance tube measurements collected with melamine foam samples. Diffuse field sound absorption measurements collected using large test articles in a laboratory are also compared with absorption predictions determined using model-based and measured foam properties. Melamine foam slabs of various thicknesses are considered.

Allen, Albert R.↗
NASA NTRSDate not supplied

Additive Manufacturing and Experimental Characterization of Nickel-Titanium Shape-Memory Alloy Wick Structures and Heat Pipes for Spacecraft Thermal Control

Shape memory alloys (SMA), such as those based on nickel-titanium (NiTi), are increasingly being applied as multifunctional spacecraft components. For thermal management applications, NiTi flow tubing hinges and self-deploying loop heat pipes have been demonstrated. Emerging additive manufacturing (AM) processes are enabling more complex SMA devices than can be formed from conventional plain wire, tubing, and sheet stock materials. This paper presents our progress toward applying powder bed fusion AM to producing porous NiTi wicks and NiTi-H2O heat pipes, which could be embedded in thermally deploying radiators for spacecraft thermal management. AM near-equiatomic NiTi (55.1 wt% Ni) porous wick specimens were produced with a range of deposition parameters. Transient acetone rate-of-rise experiments were performed to estimate wick permeability (K) and average pore radius (r_pore) values and identify parameter sets with high capillary performance. Surface treatments were evaluated to achieve hydrophilic wick structures. Evaluated treatments included chemical oxide growth with H2O2, oxide and sodium titanate growth with NaOH solution, and ultrasonic cleaning with specialty detergents that can remove hydrocarbon contaminants. The most durable hydrophilic surface conditions were obtained with the NaOH treatment. High performing wick deposition parameters were used to produce a full AM NiTi heat pipe, which was treated with NaOH solution to activate the wick. This heat pipe was operated on a test stand in the inverted configuration (upper evaporator and lower condenser), and demonstrated stable nearly isothermal operation for 150 hrs.

Thermal management↗
NASA NTRSDate not supplied

Additive Manufacturing and Experimental Characterization of Nickel-Titanium Shape-Memory Alloy Wick Structures and Heat Pipes for Spacecraft Thermal Control

Shape memory alloys (SMA), such as those based on nickel-titanium (NiTi), are increasingly being applied as multifunctional spacecraft components. For thermal management applications, NiTi flow tubing hinges and self-deploying loop heat pipes have been demonstrated. Emerging additive manufacturing (AM) processes are enabling more complex SMA devices than can be formed from conventional plain wire, tubing, and sheet stock materials. This paper presents our progress toward applying powder bed fusion AM to producing porous NiTi wicks and NiTi-H2O heat pipes, which could be embedded in thermally deploying radiators for spacecraft thermal management. AM near-equiatomic NiTi (55.1 wt% Ni) porous wick specimens were produced with a range of deposition parameters. Transient acetone rate-of-rise experiments were performed to estimate wick permeability (K) and average pore radius (r_pore) values and identify parameter sets with high capillary performance. Surface treatments were evaluated to achieve hydrophilic wick structures. Evaluated treatments included chemical oxide growth with H2O2, oxide and sodium titanate growth with NaOH solution, and ultrasonic cleaning with specialty detergents that can remove hydrocarbon contaminants. The most durable hydrophilic surface conditions were obtained with the NaOH treatment. High performing wick deposition parameters were used to produce a full AM NiTi heat pipe, which was treated with NaOH solution to activate the wick. This heat pipe was operated on a test stand in the inverted configuration (upper evaporator and lower condenser), and demonstrated stable nearly isothermal operation for 150 hrs.

Thermal management↗
NASA NTRS1982

Heat transport in porous cometary nuclei

Heat transport in cometary nuclei is important because it leads to the formation of larger tails and comae after perihelia than before, to early outbursts caused by phase transitions, and to fragmentation. The role of gases in pores in icy (H2O and H2O + CO2) nuclei in the heat transport has been investigated in the viscous and Knudsen diffusion regions. It appears that in pure H2O-ices the heat flow is affected by the presence of pores but is affected only very close to the perihelion by water vapor contained in them. On the other hand, the presence of CO2 vapor in the pores significantly increases the heat flow in mixed nuclei at temperatures above 140 - 150 K. Thus for heliocentric distances between 3 and 5 AU, the above mentioned phenomena should be considerably enhanced in proportion to the admixture of CO2 ices. The overlap and channel formation by pores in nuclei with high porosities is discussed.

Smoluchowski, R.↗
NASA NTRS1994

The Materials Chemistry of Atomic Oxygen with Applications to Anisotropic Etching of Submicron Structures in Microelectronics and the Surface Chemistry Engineering of Porous Solids

Neutral atomic oxygen is the most abundant component of the ionospheric plasma in the low Earth orbit environment (LEO; 200 to 700 kilometers altitude) and can produce significant degradation of some spacecraft materials. In order to produce a more complete understanding of the materials chemistry of atomic oxygen, the chemistry and physics of O-atom interactions with materials were determined in three radically different environments: (1) The Space Shuttle cargo bay in low Earth orbit (the EOIM-3 space flight experiment), (2) a high-velocity neutral atom beam system (HVAB) at Los Alamos National Laboratory (LANL), and (3) a microwave-plasma flowing-discharge system at JSC. The Space Shuttle and the high velocity atom beam systems produce atom-surface collision energies ranging from 0.1 to 7 eV (hyperthermal atoms) under high-vacuum conditions, while the flowing discharge system produces a 0.065 eV surface collision energy at a total pressure of 2 Torr. Data obtained in the three different O-atom environments referred to above show that the rate of O-atom reaction with polymeric materials is strongly dependent on atom kinetic energy, obeying a reactive scattering law which suggests that atom kinetic energy is directly available for overcoming activation barriers in the reaction. General relationships between polymer reactivity with O atoms and polymer composition and molecular structure have been determined. In addition, vacuum ultraviolet photochemical effects have been shown to dominate the reaction of O atoms with fluorocarbon polymers. Finally, studies of the materials chemistry of O atoms have produced results which may be of interest to technologists outside the aerospace industry. Atomic oxygen 'spin-off' or 'dual use' technologies in the areas of anisotropic etching in microelectronic materials and device processing, as well as surface chemistry engineering of porous solid materials are described.

Koontz, Steve L.↗
NASA NTRS1972

An investigation of rooftop STOL port aerodynamics

An investigation into aerodynamic problems associated with large building rooftop STOLports was performed. Initially, a qualitative flow visualization study indicated two essential problems: (1) the establishment of smooth, steady, attached flow over the rooftop, and (2) the generation of acceptable crosswind profile once (1) has been achieved. This study indicated that (1) could be achieved by attaching circular-arc rounded edge extensions to the upper edges of the building and that crosswind profiles could be modified by the addition of porous vertical fences to the lateral edges of the rooftop. Important fence parameters associated with crosswind alteration were found to be solidity, fence element number and spacing. Large scale building induced velocity fluctuations were discovered for most configurations tested and a possible explanation for their occurrence was postulated. Finally, a simple equation relating fence solidity to the resulting velocity profile was developed and tested for non-uniform single element fences with 30 percent maximum solidity.

Blanton, J. N.↗
NASA NTRS1975

Dewar technology study

The development of a Dewar system for handling liquid helium under weightless conditions is described. Porous plug designs for the prevention of superfluid creep out of the dewar through the vent line were evaluated. For the purpose of designing a neck to provide a transition from the cold cavity to the outside, the loads carried by the neck and equipment supports were studied. Temperature, pressure, and mass flow instrumentation for monitoring Dewar performance were also evaluated. In addition, multilayer blankets consisting of aluminized Mylar separated by Dacron net sheets were designed to insulate the pressure vessel. The dewar system is suggested for use with the star tracking telescope aboard the relativity satellite.

Davis, W.↗
NASA NTRS1994

Development of lightweight ceramic ablators and arc-jet test results

Lightweight ceramic ablators (LCA's) were recently developed at Ames to investigate the use of low density fibrous substrates and organic resins as high temperature, high strength ablative heat shields. Unlike the traditional ablators, LCA's use porous ceramic/carbon fiber matrices as substrates for structural support, and polymeric resins as fillers. Several substrates and resins were selected for the initial studies, and the best performing candidates were further characterized. Three arcjet tests were conducted to determine the LCA's thermal performance and ablation characteristics in a high enthalpy, hypersonic flow environment. Mass loss and recession measurements were obtained for each sample at post test, and the recession rates were determined from high speed motion films. Surface temperatures were also obtained from optical pyrometers.

Tran, Huy K.↗
NASA NTRS1976

Approximate method for calculating transonic flow about lifting wing-body configurations

The three-dimensional problem of transonic flow about lifting wing-body configurations is reduced to a two-variable computational problem with the method of matched asymptotic expansions. The computational problem is solved with the method of relaxation. The method accounts for leading-edge separation, the presence of shock waves, and the presence of solid, slotted, or porous tunnel walls. The Mach number range of the method extends from zero to the supersonic value at which the wing leading edge becomes sonic. A modified form of the transonic area rule which accounts for the effect of lift is developed. This effect is explained from simple physical considerations.

Barnwell, R. W.↗
NASA NTRS1989

Determination of combustion gas temperatures by infrared radiometry in sooting and nonsooting flames

Flame temperatures in nonsooting and sooting environments were successfully measured by radiometry for pre-mixed propane-oxygen laminar flames stabilized on a water-cooled, porous sintered-bronze burner. The measured temperatures in the nonsooting flames were compared with fine-wire thermocouple measurements. The results show excellent agreement below 1700 K, and when the thermocouple measurements were corrected for radiation effects, the agreement was good for even higher temperatures. The benefits of radiometry are: (1) the flow is not disturbed by an intruding probe, (2) calibration is easily done using a blackbody source, and (3) measurements can be made even with soot present. The theory involved in the radiometry measurements and the energy balance calculations used to correct the thermocouple temperature measurements are discussed.

Lyons, Valerie J.↗
NASA NTRS1973

Fundamental study of transpiration cooling

Isothermal and non-isothermal pressure drop data and heat transfer data generated on porous 304L stainless steel wire forms, sintered spherical stainless steel powder, and sintered spherical OFHC copper powder are reported and correlated. Pressure drop data was collected over a temperature range from 500 R to 2000 R and heat transfer data collected over a heat flux range from 5 to 15 BTU/in2/sec. It was found that flow data could be correlated independently of transpirant temperature and type (i.e., H2, N2). It was also found that no simple relation between heat transfer coefficient and specimen porosity was obtainable.

Koh, J. C. Y.↗
NASA NTRS1992

On the melt infiltration of copper coated silicon carbide with an aluminium alloy

Pressure-assisted infiltration of porous compacts of Cu coated and uncoated single crystals of platelet shaped alpha (hexagonal) SiC was used to study infiltration dynamics and particulate wettability with a 2014 Al alloy. The infiltration lengths were measured for a range of experimental variables which included infiltration pressure, infiltration time, and SiC size. A threshold pressure (P(th)) for flow initiation through compacts was identified from an analysis of infiltration data; P(th) decreased while penetration lengths increased with increasing SiC size (more fundamentally, due to changes in interparticle pore size) and with increasing infiltration times. Cu coated SiC led to lower P(th) and 60-80 percent larger penetration lengths compared to uncoated SiC under identical processing conditions.

Asthana, R.↗