Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pilot performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37

Standard Analysis Report INV-SAR-81, Revision 0 Chemical and Cement Components 2023 Inventory Estimates for the Interim State Performance Assessment of the Waste Isolation Pilot Plant

This standard analysis report provides the estimates for the chemical (oxyanions and complexing agents) and cement components with a data collection cut-off date of December 31, 2023. These estimates will be included in a Performance Assessment Inventory Report developed for the U.S. Department of Energy (DOE) interim state repository configuration performance assessment (PA) for the 2026 Compliance Recertification Application (CRA).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Development and evaluation of an inverse solution technique for studying helicopter maneuverability and agility

An inverse solution technique for determining the maximum maneuvering performance of a helicopter using smooth, pilotlike control inputs is presented. Also described is a pilot simulation experiment performed to investigate the accuracy of the solution resulting from this technique. The maneuverability and agility capability of the helicopter math model was varied by varying the pitch and roll damping, the maximum pitch and roll rate, and the maximum load-factor capability. Three maneuvers were investigated: a 180-deg turn, a longitudinal pop-up, and a lateral jink. The inverse solution technique yielded accurate predictions of pilot-in-the-loop maneuvering performance for two of the three maneuvers.

Whalley, Matthew S.↗

Primary display latency criteria based on flying qualities and performance data

With a pilots' increasing use of visual cue augmentation, much requiring extensive pre-processing, there is a need to establish criteria for new avionics/display design. The timeliness and synchronization of the augmented cues is vital to ensure the performance quality required for precision mission task elements (MTEs) where augmented cues are the primary source of information to the pilot. Processing delays incurred while transforming sensor-supplied flight information into visual cues are unavoidable. Relationships between maximum control system delays and associated flying qualities levels are documented in MIL-F-83300 and MIL-F-8785. While cues representing aircraft status may be just as vital to the pilot as prompt control response for operations in instrument meteorological conditions, presently, there are no specification requirements on avionics system latency. To produce data relating avionics system latency to degradations in flying qualities, the Navy conducted two simulation investigations. During the investigations, flying qualities and performance data were recorded as simulated avionics system latency was varied. Correlated results of the investigation indicates that there is a detrimental impact of latency on flying qualities. Analysis of these results and consideration of key factors influencing their application indicate that: (1) Task performance degrades and pilot workload increases as latency is increased. Inconsistency in task performance increases as latency increases. (2) Latency reduces the probability of achieving Level 1 handling qualities with avionics system latency as low as 70 ms. (3) The data suggest that the achievement of desired performance will be ensured only at display latency values below 120 ms. (4) These data also suggest that avoidance of inadequate performance will be ensured only at display latency values below 150 ms.

Funk, John D., Jr.↗

Pilot use of simulator cues for autorotation landings

A ground-based simulator experiment was conducted to investigate the influence of simulator cue variations on helicopter autorotation landing-task performance. Using the NASA Ames Research Center Vertical Motion Simulator (VMS), variations were made in motion-system performance and selection of either longitudinal or lateral linear acceleration cues. Analysis of landing performance statistics and pilot commentary revealed that task performance changed with degraded motion cues. However, fixed base (no motion) could provide acceptable landing performance if adequate visual cues were present. Lontitudinal linear-acceleration cues assisted one pilot's control of the landing forward speed, while lateral linear-acceleration cues assisted in control of lateral drift or sideslip. Variations were also made in the content and details of visual landing scenes. Pilot commentary collected on the use of three landing scenes stressed the importance of receiving consistent, easily recognized, position, attitude, and speed cues from the visual scene. The importance of subtle aural cues to pilot acceptance of the simulation was also noted.

Decker, W. A.↗

An Evaluation of Training Interventions and Computed Scoring Techniques for Grading a Level Turn Task and a Straight In Landing Approach on a PC-Based Flight Simulator

One result of the relatively recent advances in computing technology has been the decreasing cost of computers and increasing computational power. This has allowed high fidelity airplane simulations to be run on personal computers (PC). Thus, simulators are now used routinely by pilots to substitute real flight hours for simulated flight hours for training for an aircraft type rating thereby reducing the cost of flight training. However, FAA regulations require that such substitution training must be supervised by Certified Flight Instructors (CFI). If the CFI presence could be reduced or eliminated for certain tasks this would mean a further cost savings to the pilot. This would require that the flight simulator have a certain level of 'intelligence' in order to provide feedback on pilot perfolmance similar to that of a CFI. The 'intelligent' flight sinlulator would have at least the capability to use data gathered from the flight to create a measure for the performance of the student pilot. Also, to fully utilize the advances in computational power, the sinlulator would be capable of interacting with the student pilot using the best possible training interventions. This thesis reposts on the two studies conducted at Tuskegee University investigating the effects of interventions on the learning of two flight maneuvers on a flight sinlulator and the robustness and accuracy of calculated perfornlance indices as compared to CFI evaluations of performance. The intent of these studies is to take a step in the direction of creating an 'intelligent' flight simulator. The first study deals with the comparisons of novice pilot performance trained at different levels of above real-time to execute a level S-turn. The second study examined the effect of out-of-the-window (OTW) visual cues in the form of hoops on the performance of novice pilots learning to fly a landing approach on the flight simulator. The reliability/robustness of the computed performance metrics was assessed by comparing them with the evaluations of the landing approach maneuver by a number of CFIs.

Heath, Bruce E.↗

Identification of Time-Varying Pilot Control Behavior in Multi-Axis Control Tasks

Recent developments in fly-by-wire control architectures for rotorcraft have introduced new interest in the identification of time-varying pilot control behavior in multi-axis control tasks. In this paper a maximum likelihood estimation method is used to estimate the parameters of a pilot model with time-dependent sigmoid functions to characterize time-varying human control behavior. An experiment was performed by 9 general aviation pilots who had to perform a simultaneous roll and pitch control task with time-varying aircraft dynamics. In 8 different conditions, the axis containing the time-varying dynamics and the growth factor of the dynamics were varied, allowing for an analysis of the performance of the estimation method when estimating time-dependent parameter functions. In addition, a detailed analysis of pilots adaptation to the time-varying aircraft dynamics in both the roll and pitch axes could be performed. Pilot control behavior in both axes was significantly affected by the time-varying aircraft dynamics in roll and pitch, and by the growth factor. The main effect was found in the axis that contained the time-varying dynamics. However, pilot control behavior also changed over time in the axis not containing the time-varying aircraft dynamics. This indicates that some cross coupling exists in the perception and control processes between the roll and pitch axes.

Zaal, Peter M. T.↗

Validation of Fitness for Duty Standards Using Pre- and Post-Flight Capsule Egress and Suited Functional Performance Tasks in Simulated Reduced Gravity (Pilot Egress Fitness)

As NASA prepares for exploration missions, it will be critical to understand and build upon known crew capabilities. Specifically, we need to know the functional capacities of crew at different stages of a mission and characterize these profiles so that the appropriate vehicle requirements and mission concepts of operations (ConOps) can be developed. One of the most complex phases of any missions is when there is a transition between gravity environments. For instance, both physiological adaptation to microgravity and subsequent re-entry into a gravity environment result in reduced functional capacity, even with rigorous adherence to inflight countermeasures. Quantification of the astronauts’ post-landing functional performance is necessary to design ConOps for exploration missions. Specifically, these two high-risk tasks may have to be performed soon after gravity transitions: •Unassisted capsule egress task after return to Earth •Planetary extravehicular activity (EVA) soon after landing on Mars or the Moon This study has been broken down into two phases. A pilot phase to assess the overall feasibility and demonstrate the capability to do these tasks shortly after landing and the full Egress Fitness study, which will be part of the CIPHER complement. This study uses a functional task approach to characterize performance of these high-risk tasks in long-duration ISS crewmembers before flight and shortly after return to Earth. Prior to any testing, each astronaut subject completes a suit fit check to ensure adequate sizing and mobility to be able to complete the EVA tasks. Pilot Egress Fitness pre-flight and post-flight testing includes an Earth based emergency egress out of a functional capsule mockup, and a short Mars gravity EVA simulation including suit donning, hatch egress, ladder descent, task board cable operations, baggage transfer over sand/rocky regolith, alignment with a rear entry port, and suit egress. Pre-flight testing can occur almost anytime pre-flight, but post-flight scheduling is much more critical with the capsule egress test occurring 1-4 hours after landing and the planetary EVA approximately 18-36 hours after landing. Data collected for both tasks includes task completion time, photo, and video. The EVA portion also includes collection of metabolic and heart rate. Pilot Egress Fitness study has completed baseline pre-flight testing on 3 astronaut subjects. Post-flight testing of the first two subjects will be completed in November 2021 and the final subject around March 2022. Results and lessons learned from this pilot study will inform the full Egress Fitness study, which will incorporate additional pre-flight sessions, longer EVA tasks, and post-flight testing on R+1, 4, and 7 to characterize the timeframe of recovery

J R Norcross↗

Evaluation of Flying Qualities and Guidance Displays for an Advanced Tilt-Wing STOL Transport Aircraft in Final Approach and Landing

A piloted simulation was performed on the Vertical Motion Simulator at NASA Ames Research Center to evaluate flying qualities of a tilt-wing Short Take-Off and Landing (STOL) transport aircraft during final approach and landing. The experiment was conducted to assess the design s handling qualities, and to evaluate the use of flightpath-centered guidance for the precision approach and landing tasks required to perform STOL operations in instrument meteorological conditions, turbulence, and wind. Pilots rated the handling qualities to be satisfactory for all operations evaluated except those encountering extreme crosswinds and severe windshear; even in these difficult meteorological conditions, adequate handling qualities were maintained. The advanced flight control laws and guidance displays provided consistent performance and precision landings.

Frost, Chad R.↗

Cockpit resource management - Exploring the attitude-performance linkage

Measured attitudes regarding cockpit management were contrasted for pilots whose line flying performance was independently evaluated by check airmen as above or below average. A highly significant discriminant function was obtained indicating that these attitudes are significant predictors of behavior. The performance of 95.7 percent of the pilots was correctly classified by the analysis. Implications of the results for cockpit resource management training and pilot selection are discussed.

Helmreich, R. L.↗

Analytical study of the cruise performance of a class of remotely piloted, microwave-powered, high-altitude airplane platforms

Each cycle of the flight profile consists of climb while the vehicle is tracked and powered by a microwave beam, followed by gliding flight back to a minimum altitude. Parameter variations were used to define the effects of changes in the characteristics of the airplane aerodynamics, the power transmission systems, the propulsion system, and winds. Results show that wind effects limit the reduction of wing loading and increase the lift coefficient, two effective ways to obtain longer range and endurance for each flight cycle. Calculated climb performance showed strong sensitivity to some power and propulsion parameters. A simplified method of computing gliding endurance was developed.

Morris, C. E. K., Jr.↗

A piloted-simulation evaluation of two electronic display formats for approach and landing

The results of a piloted-simulation evaluation of the benefits of adding runway symbology and track information to a baseline electronic-attitude-director-indicator (EADI) format for the approach-to-landing task were presented. The evaluation was conducted for the baseline format and for the baseline format with the added symbology during 3 deg straight-in approaches with calm, cross-wind, and turbulence conditions. Flight-path performance data and pilot subjective comments were examined with regard to the pilot's tracking performance and mental workload for both display formats. The results show that the addition of a perspective runway image and relative track information to a basic situation-information EADI format improve the tracking performance both laterally and vertically during an approach-to-landing task and that the mental workload required to assess the approach situation was thus reduced as a result of integration of information.

Steinmetz, G. G.↗

Landing performance by low-time private pilots after the sudden loss of binocular vision - Cyclops II

Study of low-time general aviation pilots, who, in a series of spot landings, were suddenly deprived of binocular vision by patching either eye on the downwind leg of a standard, closed traffic pattern. Data collected during these landings were compared with control data from landings flown with normal vision during the same flight. The sequence of patching and the mix of control and monocular landings were randomized to minimize the effect of learning. No decrease in performance was observed during landings with vision restricted to one eye, in fact, performance improved. This observation is reported at a high level of confidence (p less than 0.001). These findings confirm the previous work of Lewis and Krier and have important implications with regard to aeromedical certification standards.

Lewis, C. E., Jr.↗

Alertness management in two-person long-haul flight operations

Long-haul flight operations involve cumulative sleep loss, circadian disruption, and extended and irregular duty schedules. These factors reduce pilot alertness and performance on the flightdeck. Conceptually and operationally, alertness management in flight operations can be divided into preventive strategies and operational countermeasures. Preventive strategies are utilized prior to a duty period to mitigate or reduce the effects of sleep loss, circadian disruption and fatigue during subsequent flight operations. Operational countermeasures are used during operations as acute techniques for maintaining performance and alertness. Results from previous NASA Ames field studies document the sleep loss and circadian disruption in three-person long-haul flying and illustrate the application of preventive strategies and operational countermeasures. One strategy that can be used in both a preventive and operational manner is strategic napping. The application and effectiveness of strategic napping in long-haul operations will be discussed. Finally, long-haul flying in two-person highly automated aircraft capable of extended range operations will create new challenges to maintaining pilot alertness and performance. Alertness management issues in this flight environment will be explored.

Rosekind, M. R.↗

A Novel High‐Performance Electrolyte for Extreme Fast Charging in Pilot Scale Lithium‐Ion Pouch Cells

Realizing extreme fast charging (XFC) in lithium-ion batteries for electric vehicles is still challenging due to the insufficient lithium-ion transport kinetics, especially in the electrolyte. Herein, a novel high-performance electrolyte (HPE) consisting of lithium bis(fluorosulfonyl)imide (LiFSI), lithium hexafluorophosphate (LiPF 6 ) and carbonates is proposed and tested in pilot-scale, 2-Ah pouch cells. Moreover, the origin of improved electrochemical performance is comprehensively studied via various characterizations, suggesting that the proposed HPE exhibits high ionic conductivity and excellent electrochemical stability at high charging rate of 6-C. Furthermore, the HPE-based pouch cells deliver improved discharge specific capacity and excellent long-term cyclability up to 1500 cycles under XFC conditions, which is superior to the conventional state-of-the-art baseline electrolyte.

25 ENERGY STORAGE↗

Assessing Helicopter Pilots’ Detect and Avoid and Collision Avoidance Performance With ACAS Xr

The latest variant of the Federal Aviation Administration’s Airborne Collision Avoidance System (ACAS X) is being designed for both crewed and uncrewed rotorcraft. Referred to as ACAS Xr, the system joins a suite of other ACAS X variants poised to replace the Traffic Alert and Collision Avoidance System (TCAS II). ACAS Xr is tuned to support current-day helicopter platforms as well as electric Vertical Takeoff and Landing (eVTOL) vehicles that are still under development. Given this flexibility, ACAS Xr may be used by helicopter crews currently in operation or by remotely-operated eVTOL aircraft in the emerging Advanced Air Mobility (AAM) market. To cover the range of potential uses, two distinct configurations are being proposed for ACAS Xr: Collision Avoidance System (CAS) and Detect and Avoid (DAA). Under the CAS configuration, ACAS Xr provides minimal caution-level alerting but issues directive warning-level alerting and guidance. The DAA configuration, by contrast, provides caution-level alerting and guidance, in addition to the warning-level alerting and guidance. The current study was performed as part of the National Aeronautics and Space Administration’s AAM project. Six helicopter pilots were recruited to fly a variety of scripted traffic scenarios in a full-motion, crewed eVTOL simulator. Participants flew 60 encounters over two days, reacting to pre-recorded intruder aircraft that were scripted to fly into the participant’s aircraft from different approach angles, relative altitudes, and during different phases of flight. The pilots flew half of the encounters with the CAS configuration and half with the DAA configuration. Within each block of 30 encounters, pilots experienced 10 conflicts while in cruise, 10 in hover, and 10 while on approach to a heliport. Results showed that pilot response times were consistently under 5 seconds for RAs and under 10 seconds for DAA alerts, when present, during all three phases of flight. Unsurprisingly, the DAA configuration was associated with lower rates of en-route and high-severity losses of DAA well clear compared to the CAS configuration in all phases of flight except for the terminal area. Rates of losses of DAA well clear were found to be substantially higher in the Hover scenario, compared to Cruise. Pilots failed to fully comply with RAs at a rate of 0.10-0.18 in all conditions except for the DAA configuration in the Hover scenario, which was associated with a higher non-compliance rate of 0.4 due to Descend RAs issued at low altitudes. The implications of these results with regards to the ongoing development of ACAS Xr is discussed.

air taxis↗

Assessing Helicopter Pilots’ Detect and Avoid and Collision Avoidance Performance with ACAS Xr

The latest variant of the Federal Aviation Administration’s Airborne Collision Avoidance System (ACAS X) is being designed for both crewed and uncrewed rotorcraft. Referred to as ACAS Xr, the system joins a suite of other ACAS X variants poised to replace the Traffic Alert and Collision Avoidance System (TCAS II). ACAS Xr is tuned to support current-day helicopter platforms as well as electric Vertical Takeoff and Landing (eVTOL) vehicles that are still under development. Given this flexibility, ACAS Xr may be used by helicopter crews currently in operation or by remotely-operated eVTOL aircraft in the emerging Advanced Air Mobility (AAM) market. To cover the range of potential uses, two distinct configurations are being proposed for ACAS Xr: Collision Avoidance System (CAS) and Detect and Avoid (DAA). Under the CAS configuration, ACAS Xr provides minimal caution-level alerting but issues directive warning-level alerting and guidance. The DAA configuration, by contrast, provides caution-level alerting and guidance, in addition to the warning-level alerting and guidance. The current study was performed as part of the National Aeronautics and Space Administration’s AAM project. Six helicopter pilots were recruited to fly a variety of scripted traffic scenarios in a full-motion, crewed eVTOL simulator. Participants flew 60 encounters over two days, reacting to pre-recorded intruder aircraft that were scripted to fly into the participant’s aircraft from different approach angles, relative altitudes, and during different phases of flight. The pilots flew half of the encounters with the CAS configuration and half with the DAA configuration. Within each block of 30 encounters, pilots experienced 10 conflicts while in cruise, 10 in hover, and 10 while on approach to a heliport. Results showed that pilot response times were consistently under 5 seconds for RAs and under 10 seconds for DAA alerts, when present, during all three phases of flight. Unsurprisingly, the DAA configuration was associated with lower rates of en-route and high-severity losses of DAA well clear compared to the CAS configuration in all phases of flight except for the terminal area. Rates of losses of DAA well clear were found to be substantially higher in the Hover scenario, compared to Cruise. Pilots failed to fully comply with RAs at a rate of 0.10-0.18 in all conditions except for the DAA configuration in the Hover scenario, which was associated with a higher non-compliance rate of 0.4 due to Descend RAs issued at low altitudes. The implications of these results with regards to the ongoing development of ACAS Xr is discussed.

air taxis↗

STS-114: Discovery TCDT Flight Crew Test Media Event at Pad 39-B

The STS-114 Space Shuttle Discovery Terminal Countdown Demonstration Test (TCDT) flight crew is shown at Pad 39-B. Eileen Collins, Commander introduces the astronauts. Andrew Thomas, mission specialist talks about his primary responsibility of performing boom inspections, Wendy Lawrence, Mission Specialist 4 (MS4) describes her role as the robotic arm operator supporting Extravehicular Activities (EVA), Stephen Robinson, Mission Specialist 3 (MS3) talks about his role as flight engineer, Charlie Camarda, Mission Specialist 5 (MS5) says that his duties are to perform boom operations, transfer operations from the space shuttle to the International Space Station and spacecraft rendezvous. Soichi Noguchi, Mission Specialist 1 (MS1) from JAXA, introduces himself as Extravehicular Activity 1 (EVA1), and Jim Kelley, Pilot will operate the robotic arm and perform pilot duties. Questions from the news media about the safety of the external tank, going to the International Space Station and returning, EVA training, and thoughts about the Space Shuttle Columbia crew are answered.

Source record↗

The effect of spurious angular accelerations on tracking in dynamic simulation

A laboratory study was conducted to investigate the effect of spurious simulator yaw motions on a pilot's control performance. A second objective was to compare the efficiency of static and dynamic simulator tracking in previously unexamined vehicle dynamics. Twelve airline pilots served as subjects in a moving-base flight simulator under congruent-motion, spurious-motion, and no-motion conditions. The results indicated a significant increase in the amount of error with increasing levels of spurious motion during the initially administered series of trials. The influence of spurious motion, however, was absent in a second series of trials. The data suggest that the pilots learned to compensate in their performance for the spurious inputs. It was also found that congruent visual and rotational cueing produced superior performance to that of tracking with visual information alone.

Beck, L. J.↗