Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Parallel application”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Control of cytoskeletal mechanics by extracellular matrix, cell shape, and mechanical tension

We have investigated how extracellular matrix (ECM) alters the mechanical properties of the cytoskeleton (CSK). Mechanical stresses were applied to integrin receptors on the apical surfaces of adherent endothelial cells using RGD-coated ferromagnetic microbeads (5.5-microns diameter) in conjunction with a magnetic twisting device. Increasing the number of basal cell-ECM contacts by raising the fibronectin (FN) coating density from 10 to 500 ng/cm2 promoted cell spreading by fivefold and increased CSK stiffness, apparent viscosity, and permanent deformation all by more than twofold, as measured in response to maximal stress (40 dyne/cm2). When the applied stress was increased from 7 to 40 dyne/cm2, the stiffness and apparent viscosity of the CSK increased in parallel, although cell shape, ECM contacts, nor permanent deformation was altered. Application of the same stresses over a lower number ECM contacts using smaller beads (1.4-microns diameter) resulted in decreased CSK stiffness and apparent viscosity, confirming that this technique probes into the depth of the CSK and not just the cortical membrane. When magnetic measurements were carried out using cells whose membranes were disrupted and ATP stores depleted using saponin, CSK stiffness and apparent viscosity were found to rise by approximately 20%, whereas permanent deformation decreased by more than half. Addition of ATP (250 microM) under conditions that promote CSK tension generation in membrane-permeabilized cells resulted in decreases in CSK stiffness and apparent viscosity that could be detected within 2 min after ATP addition, before any measurable change in cell size.(ABSTRACT TRUNCATED AT 250 WORDS).

Non-NASA Center↗
NASA NTRS1991

Passively forced current sharing among transistors

This application concerns a simple passive circuit that improves current balance in paralleled power MOSFETs that are not precisely matched and that are operated in their active region from a common gate drive. A nonlinear circuit consisting of diodes and resistors generates a differential gate potential required to correct for unbalance while maintaining low losses over a range of current.

Niedra, Janis M.↗
NASA NTRS2009

A Survey of New Trends in Symbolic Execution for Software Testing and Analysis

Symbolic execution is a well-known program analysis technique which represents values of program inputs with symbolic values instead of concrete (initialized) data and executes the program by manipulating program expressions involving the symbolic values. Symbolic execution has been proposed over three decades ago but recently it has found renewed interest in the research community, due in part to the progress in decision procedures, availability of powerful computers and new algorithmic developments. We provide a survey of some of the new research trends in symbolic execution, with particular emphasis on applications to test generation and program analysis. We first describe an approach that handles complex programming constructs such as input data structures, arrays, as well as multi-threading. We follow with a discussion of abstraction techniques that can be used to limit the (possibly infinite) number of symbolic configurations that need to be analyzed for the symbolic execution of looping programs. Furthermore, we describe recent hybrid techniques that combine concrete and symbolic execution to overcome some of the inherent limitations of symbolic execution, such as handling native code or availability of decision procedures for the application domain. Finally, we give a short survey of interesting new applications, such as predictive testing, invariant inference, program repair, analysis of parallel numerical programs and differential symbolic execution.

Pasareanu, Corina S.↗
NASA NTRS2010

Efficient Parallel Engineering Computing on Linux Workstations

A C software module has been developed that creates lightweight processes (LWPs) dynamically to achieve parallel computing performance in a variety of engineering simulation and analysis applications to support NASA and DoD project tasks. The required interface between the module and the application it supports is simple, minimal and almost completely transparent to the user applications, and it can achieve nearly ideal computing speed-up on multi-CPU engineering workstations of all operating system platforms. The module can be integrated into an existing application (C, C++, Fortran and others) either as part of a compiled module or as a dynamically linked library (DLL).

Lou, John Z.↗
NASA NTRS2002

Maximizing TDRS Command Load Lifetime

The GNC software onboard ISS utilizes TORS command loads, and a simplistic model of TORS orbital motion to generate onboard TORS state vectors. Each TORS command load contains five "invariant" orbital elements which serve as inputs to the onboard propagation algorithm. These elements include semi-major axis, inclination, time of last ascending node crossing, right ascension of ascending node, and mean motion. Running parallel to the onboard software is the TORS Command Builder Tool application, located in the JSC Mission Control Center. The TORS Command Builder Tool is responsible for building the TORS command loads using a ground TORS state vector, mirroring the onboard propagation algorithm, and assessing the fidelity of current TORS command loads onboard ISS. The tool works by extracting a ground state vector at a given time from a current TORS ephemeris, and then calculating the corresponding "onboard" TORS state vector at the same time using the current onboard TORS command load. The tool then performs a comparison between these two vectors and displays the relative differences in the command builder tool GUI. If the RSS position difference between these two vectors exceeds the tolerable lim its, a new command load is built using the ground state vector and uplinked to ISS. A command load's lifetime is therefore defined as the time from when a command load is built to the time the RSS position difference exceeds the tolerable limit. From the outset of TORS command load operations (STS-98), command load lifetime was limited to approximately one week due to the simplicity of both the onboard propagation algorithm, and the algorithm used by the command builder tool to generate the invariant orbital elements. It was soon desired to extend command load lifetime in order to minimize potential risk due to frequent ISS commanding. Initial studies indicated that command load lifetime was most sensitive to changes in mean motion. Finding a suitable value for mean motion was therefore the key to achieving this goal. This goal was eventually realized through development of an Excel spreadsheet tool called EMMIE (Excel Mean Motion Interactive Estimation). EMMIE utilizes ground ephemeris nodal data to perform a least-squares fit to inferred mean anomaly as a function of time, thus generating an initial estimate for mean motion. This mean motion in turn drives a plot of estimated downtrack position difference versus time. The user can then manually iterate the mean motion, and determine an optimal value that will maximize command load lifetime. Once this optimal value is determined, the mean motion initially calculated by the command builder tool is overwritten with the new optimal value, and the command load is built for uplink to ISS. EMMIE also provides the capability for command load lifetime to be tracked through multiple TORS ephemeris updates. Using EMMIE, TORS command load lifetimes of approximately 30 days have been achieved.

Brown, Aaron J.↗
NASA NTRS2003

Evaluation of Cache-based Superscalar and Cacheless Vector Architectures for Scientific Computations

The growing gap between sustained and peak performance for scientific applications has become a well-known problem in high performance computing. The recent development of parallel vector systems offers the potential to bridge this gap for a significant number of computational science codes and deliver a substantial increase in computing capabilities. This paper examines the intranode performance of the NEC SX6 vector processor and the cache-based IBM Power3/4 superscalar architectures across a number of key scientific computing areas. First, we present the performance of a microbenchmark suite that examines a full spectrum of low-level machine characteristics. Next, we study the behavior of the NAS Parallel Benchmarks using some simple optimizations. Finally, we evaluate the perfor- mance of several numerical codes from key scientific computing domains. Overall results demonstrate that the SX6 achieves high performance on a large fraction of our application suite and in many cases significantly outperforms the RISC-based architectures. However, certain classes of applications are not easily amenable to vectorization and would likely require extensive reengineering of both algorithm and implementation to utilize the SX6 effectively.

Oliker, Leonid↗
NASA NTRS1987

An application of the MPP to the interactive manipulation of stereo images of digital terrain models

Massively Parallel Processor algorithms were developed for the interactive manipulation of flat shaded digital terrain models defined over grids. The emphasis is on real time manipulation of stereo images. Standard graphics transformations are applied to a 128 x 128 grid of elevations followed by shading and a perspective projection to produce the right eye image. The surface is then rendered using a simple painter's algorithm for hidden surface removal. The left eye image is produced by rotating the surface 6 degs about the viewer's y axis followed by a perspective projection and rendering of the image as described above. The left and right eye images are then presented on a graphics device using standard stereo technology. Performance evaluations and comparisons are presented.

Pol, Sanjay↗
NASA NTRS1987

A generic applications subroutine library for the MPP

A new methodology to increase the utility of the Massively Parallel Processor (MPP) was developed, and is presented as an addition to the current methods of using the MPP. This methodology provides for the development of an MPP side abstraction layer that is callable from any host side high level language. Routines in the abstraction layer have the option of using a powerful software tool for accessing the stager as virtual memory. An additional abstraction layer that allows for remote access to the MPP via DECnet is discussed. This integrated approach to programming the MPP is a valuable tool for the implementation of interactive user driver systems that require the computational capabilities of the MPP as well as a controlled user view. It is expected that this methodology will be used to integrate the MPP into many such systems, and thus promote greater use of the MPP by scientific researchers who are accustomed to user friendly environments.

Gough, Michael L.↗
NASA NTRS2012

Downsampling Photodetector Array with Windowing

In a photon counting detector array, each pixel in the array produces an electrical pulse when an incident photon on that pixel is detected. Detection and demodulation of an optical communication signal that modulated the intensity of the optical signal requires counting the number of photon arrivals over a given interval. As the size of photon counting photodetector arrays increases, parallel processing of all the pixels exceeds the resources available in current application-specific integrated circuit (ASIC) and gate array (GA) technology; the desire for a high fill factor in avalanche photodiode (APD) detector arrays also precludes this. Through the use of downsampling and windowing portions of the detector array, the processing is distributed between the ASIC and GA. This allows demodulation of the optical communication signal incident on a large photon counting detector array, as well as providing architecture amenable to algorithmic changes. The detector array readout ASIC functions as a parallel-to-serial converter, serializing the photodetector array output for subsequent processing. Additional downsampling functionality for each pixel is added to this ASIC. Due to the large number of pixels in the array, the readout time of the entire photodetector is greater than the time between photon arrivals; therefore, a downsampling pre-processing step is done in order to increase the time allowed for the readout to occur. Each pixel drives a small counter that is incremented at every detected photon arrival or, equivalently, the charge in a storage capacitor is incremented. At the end of a user-configurable counting period (calculated independently from the ASIC), the counters are sampled and cleared. This downsampled photon count information is then sent one counter word at a time to the GA. For a large array, processing even the downsampled pixel counts exceeds the capabilities of the GA. Windowing of the array, whereby several subsets of pixels are designated for processing, is used to further reduce the computational requirements. The grouping of the designated pixel frame as the photon count information is sent one word at a time to the GA, the aggregation of the pixels in a window can be achieved by selecting only the designated pixel counts from the serial stream of photon counts, thereby obviating the need to store the entire frame of pixel count in the gate array. The pixel count se quence from each window can then be processed, forming lower-rate pixel statistics for each window. By having this processing occur in the GA rather than in the ASIC, future changes to the processing algorithm can be readily implemented. The high-bandwidth requirements of a photon counting array combined with the properties of the optical modulation being detected by the array present a unique problem that has not been addressed by current CCD or CMOS sensor array solutions.

Patawaran, Ferze D.↗
NASA NTRS2011

Lightweight High Efficiency Electric Motors for Space Applications

Lightweight high efficiency electric motors are needed across a wide range of space applications from - thrust vector actuator control for launch and flight applications to - general vehicle, base camp habitat and experiment control for various mechanisms to - robotics for various stationary and mobile space exploration missions. QM Power?s Parallel Path Magnetic Technology Motors have slowly proven themselves to be a leading motor technology in this area; winning a NASA Phase II for "Lightweight High Efficiency Electric Motors and Actuators for Low Temperature Mobility and Robotics Applications" a US Army Phase II SBIR for "Improved Robot Actuator Motors for Medical Applications", an NSF Phase II SBIR for "Novel Low-Cost Electric Motors for Variable Speed Applications" and a DOE SBIR Phase I for "High Efficiency Commercial Refrigeration Motors" Parallel Path Magnetic Technology obtains the benefits of using permanent magnets while minimizing the historical trade-offs/limitations found in conventional permanent magnet designs. The resulting devices are smaller, lower weight, lower cost and have higher efficiency than competitive permanent magnet and non-permanent magnet designs. QM Power?s motors have been extensively tested and successfully validated by multiple commercial and aerospace customers and partners as Boeing Research and Technology. Prototypes have been made between 0.1 and 10 HP. They are also in the process of scaling motors to over 100kW with their development partners. In this paper, Parallel Path Magnetic Technology Motors will be discussed; specifically addressing their higher efficiency, higher power density, lighter weight, smaller physical size, higher low end torque, wider power zone, cooler temperatures, and greater reliability with lower cost and significant environment benefit for the same peak output power compared to typically motors. A further discussion on the inherent redundancy of these motors for space applications will be provided.

Robertson, Glen A.↗
NASA NTRS2016

Utilizing GPUs to Accelerate Turbomachinery CFD Codes

GPU computing has established itself as a way to accelerate parallel codes in the high performance computing world. This work focuses on speeding up APNASA, a legacy CFD code used at NASA Glenn Research Center, while also drawing conclusions about the nature of GPU computing and the requirements to make GPGPU worthwhile on legacy codes. Rewriting and restructuring of the source code was avoided to limit the introduction of new bugs. The code was profiled and investigated for parallelization potential, then OpenACC directives were used to indicate parallel parts of the code. The use of OpenACC directives was not able to reduce the runtime of APNASA on either the NVIDIA Tesla discrete graphics card, or the AMD accelerated processing unit. Additionally, it was found that in order to justify the use of GPGPU, the amount of parallel work being done within a kernel would have to greatly exceed the work being done by any one portion of the APNASA code. It was determined that in order for an application like APNASA to be accelerated on the GPU, it should not be modular in nature, and the parallel portions of the code must contain a large portion of the code's computation time.

computer programming↗
NASA NTRS1997

High-Temperature Superconducting/Ferroelectric Structures for Tunable Microwave Components

At the NASA Lewis Research Center, ferroelectric films, such as SrTiO3 and Ba(x)Sr(1-x)TiO3, are being used in conjunction with YBa2Cu3O(7-delta) high-temperature superconducting (HTS) thin films to fabricate tunable microwave components, such as filters, varactors, and local oscillators. These structures capitalize on the variation of the dielectric constant of the ferroelectric film upon the application of a dc electric field as well as on the low microwave losses exhibited by the high-temperature superconducting films relative to their conventional conductor counterparts. (For example, the surface resistance for a YBa2Cu3O(7-delta) thin film at 10 GHz and 77 K is more than two orders of magnitude lower than that of copper at the same frequency and temperature.) SrTiO3 and Ba(x)Sr(1-x)TiO3 films are used because their crystal structure and lattice parameters are similar to those of YBa2Cu3O(7-delta), thus enabling the growth of highly textured YBa2Cu3O(7-delta) films with high critical current densities on the underlying ferroelectric film, or alternatively, of highly textured ferroelectric film on the underlying YBa2Cu3O(7-delta) film. Our efforts have been concentrated so far in determining the deposition parameters required for optimal ferroelectric thin-film growth (i.e., maximum tunability and lowest loss) and in investigating different varactor configurations to determine which geometry is the most advantageous in terms of tunability, losses, and required bias for a given communication application. For example, we have observed that for optimized SrTiO3 films in a parallel plate capacitor, tunabilities of up to 47 percent and dissipation losses (tan d) of 0.05 are attainable at 1 MHz , 80 K, and within the 0- to 5-V bias range. In contrast, for an interdigital configuration, tunabilities of up to 70 percent and tan d ranging from 0.015 to 0.001 (depending on bias) have been observed at 1 MHz and 77 K within the 0- to 100-V bias range. Efforts are underway to use these results in developing tunable receiver front-end preselect filters as well as in low-phase noise, tunable local oscillators for K-band applications. These components represent a hitherto unavailable technology to meet the stringent performance requirements of foreseeable satellite and wireless communication systems (e.g., bandwidth, in-band insertion losses, out-of-band rejection, and noise, amongst others) in a more advantageous fashion than with currently available technology (e.g., dielectric-filled cavity and waveguide filters, and dielectric resonator oscillators). Prototypes of high-temperature superconducting/ferroelectric tunable components such as a low-phase noise K-band local oscillator, a preselect C-band filter, and a low-loss K-band phase shifter are under development at NASA Lewis.

Miranda, Felix A.↗
NASA NTRS1989

Benchmarking Ada tasking on tightly coupled multiprocessor architectures

The development of benchmarks and performance measures for parallel Ada tasking is reported with emphasis on the macroscopic behavior of the benchmark across a set of load parameters. The application chosen for the study was the NASREM model for telerobot control, relevant to many NASA missions. The results of the study demonstrate the potential of parallel Ada in accomplishing the task of developing a control system for a system such as the Flight Telerobotic Servicer using the NASREM framework.

Collard, Philippe↗
NASA NTRS1989

Parallel Architectures and Parallel Algorithms for Integrated Vision Systems

Computer vision is regarded as one of the most complex and computationally intensive problems. An integrated vision system (IVS) is a system that uses vision algorithms from all levels of processing to perform for a high level application (e.g., object recognition). An IVS normally involves algorithms from low level, intermediate level, and high level vision. Designing parallel architectures for vision systems is of tremendous interest to researchers. Several issues are addressed in parallel architectures and parallel algorithms for integrated vision systems.

Choudhary, Alok Nidhi↗
NASA NTRS1994

Parallel Computational Fluid Dynamics: Current Status and Future Requirements

One or the key objectives of the Applied Research Branch in the Numerical Aerodynamic Simulation (NAS) Systems Division at NASA Allies Research Center is the accelerated introduction of highly parallel machines into a full operational environment. In this report we discuss the performance results obtained from the implementation of some computational fluid dynamics (CFD) applications on the Connection Machine CM-2 and the Intel iPSC/860. We summarize some of the experiences made so far with the parallel testbed machines at the NAS Applied Research Branch. Then we discuss the long term computational requirements for accomplishing some of the grand challenge problems in computational aerosciences. We argue that only massively parallel machines will be able to meet these grand challenge requirements, and we outline the computer science and algorithm research challenges ahead.

Simon, Horst D.↗
NASA NTRS2023

Cloud Computing Option for Modeling the Debris Environment

NASA’s Digital Transformation Initiative aims to promote the agency’s adoption of current and evolving digital technologies. Through agency-wide collaboration with other NASA teams, the Office of Safety and Mission Assurance (OSMA) has directed the Orbital Debris Program Office and the Meteoroid Environment Office to integrate cloud computing technologies into their publicly released software models: the Orbital Debris Engineering Model (ORDEM) and the Meteoroid Engineering Model (MEM). Decoupling the user interface from the backend processor was key for the software packages to run on a cloud computing framework. Benefits to this design include horizontal scaling of computing resources, user authentication and authorization, and automated deployment. Both models are hosted on a cloud computing platform supported by the NASA authorized IT security and compliance framework. This paper focuses on the new ORDEM web application, which includes the current features of the publicly released ORDEM software with an upgraded frontend design, although parallels between ORDEM and MEM are also discussed. The underlying ORDEM processor is run on a cloud container, allowing the user to run multiple spacecraft and telescope/radar mode simulations. Features exclusive to the ORDEM web application, such as importing multiple TLEs, auto-generated plotting, and the ability to check runtime progress are discussed. Comparisons between the current ORDEM software and the web application are summarized.

Andrew Vavrin↗
NASA NTRS1985

Parallel VLSI Architecture

Fermat number transformation convolutes two digital data sequences. Very-large-scale integration (VLSI) applications, such as image and radar signal processing, X-ray reconstruction, and spectrum shaping, linear convolution of two digital data sequences of arbitrary lenghts accomplished using Fermat number transform (ENT).

Truong, T. K.↗