Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLATES - TENSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 667 records · Page 37
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

MLEP-Fail calibration for 1/8 inch thick cast plate of 17-4 steel.

The purpose of the work presented in this memo was to calibrate the Sierra material model Multilinear Elastic-Plastic Hardening Model with Failure (MLEP-Fail) for 1/8 inch thick cast plate of 17-4 steel. The calibration approach is essentially the same as that recently used in a previous memo using data from smooth and notched tensile specimens. The notched specimens were manufactured with three notch radii R = 1=8, 1/32 and 1/64 inches. The dimensions of the smooth and notched specimens are given in the prints in Appendix A. Two cast plates, Plate 3 and Plate 4, with nominally identical properties were considered.

42 ENGINEERING↗
DOE OSTI2019

Fuel Plate Surface Temperature in a Fully-Uncovered Fuel Assembly after a Loss-of-Coolant Accident in an MTR-Type Research Reactor

A methodology and model that were developed in the 1960s for calculating the peak fuel temperature in an MTR fuel assembly in a reactor core that has been fully-uncovered in a hypothetical loss-of-coolant accident (LOCA) are revived and updated in this report. The semi-empirical one-node model is based on experiments on fuel elements for the Oak Ridge Research Reactor (ORR) and the Low Intensity Testing Reactor (LITR) that were done in the 1950s and 1960s at the Oak Ridge National Laboratory. The peak plate temperature in 18 LOCA tests in the ORR and two of 24 tests in the LITR, calculated using the model, are compared with experiments. The original model was used in LOCA analyses for the Omega West Reactor (OWR) at Los Alamos National Laboratory with HEU fuel and for three cores of the University of Virginia Reactor (UVAR) with both HEU and LEU fuels. The LOCA analyses for UVAR using this model were accepted for licensing purposes by the US Nuclear Regulatory Commission for an assembly containing 12 HEU fuel plates in 1970, an assembly containing 18 HEU fuel plates in 1984, and an assembly containing 22 LEU silicide fuel plates in 1994. The analyses done for the OWR and UVAR are repeated here and compared with data in the original reports in order to establish the validity of the model revived in this report. The model is then used in a subsequent LOCA analysis for the HEU and LEU cores of the RPI MTR-type reactor in Portugal. It can also be applied to other MTR-type reactors with designs similar to the LITR.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Characterization of the Sub-mm Delay Plates for the IOTA Optical-Stochastic-Cooling Experiment

This note describes the methods used to measure the thickness profile of the glass plates used in the optical-delay line of the Optical Stochastic Cooling (OSC) experiment at the Fermilab’s IOTA ring. The plates have a nominal thickness of 250 μm and the measurement was performed to verify the nominal thickness and determine its variation over the entire plate surface. All the available plates were characterized and the impact of the thickness variation on the radiation wave front was found to be negligible using wave-optics simulation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Effect of Lateral Conduction in a Rectangular Fuel Plate and Optimum Stripe Widths for the OPAL Reactor

The impetus for this work is the Proliferation Resistance Optimization (PRO-X) program, which was created by the National Nuclear Security Administration (NNSA) of the US Department of Energy (DOE) to provide a framework for developing reactor designs that minimize the production of special nuclear materials while maximizing performance for peaceful uses. The Argentine company INVAP and Argonne National Laboratory collaborated to share knowledge and expertise regarding the thermal analysis of research reactors. Working together, they designed a series of test problems based on the Open Pool Australian Light Water (OPAL) reactor, whose fuel is in the form of flat plates cooled by water flowing through narrow rectangular channels. ANL used their PLTEMP/ANL code. INVAP used their TERMIC code (and its new multi-plate version, TERMIC-MP). Then, INVAP and ANL compared the two sets of results. 1-D models were used during the collaboration since for research reactor analysis, largely 1-D thermal-hydraulics models are commonly used because they are simple to apply and technically defendable. The collaboration between the two organizations aims for improvements in thermal-hydraulic models. Improvements to methods and models can reduce modeling uncertainties and excessive conservatism, allowing greater reactor performance without reducing predicted safety margins. Therefore, these improvements potentially expand the design space, making additional designs feasible, which, in turn, may achieve better fuel utilization and proliferation resistance in the designs. This report provides justification for the lateral node size (stripe width) chosen for the 1-D computer models during the collaboration. The lateral heat conduction in OPAL fuel plates is evaluated using the two-dimensional conduction capability of PLTEMP/ANL to determine a representative hot-stripe width that can be conservatively used for one-dimensional steady-state thermal-hydraulic analysis. Basically, a representative hot-stripe width needs to be selected so that the actual heat flux averaged over this stripe width is greater than or equal to the maximum heat flux obtained by the two-dimensional analysis. Detailed results in this report show that a hot-stripe width of 8.125 mm can be conservatively used for the one-dimensional thermal-hydraulics analysis of all plates. Therefore, eight equal stripes (8.125 mm each) are recommended to be modeled in the MCNP and PLTEMP/ANL full core models of the OPAL reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Preliminary Design of Critical Experiments Involving Commercially Available B 4 C Neutron Absorber Plates with Low-Enriched UO 2 Fuel [Slides]

Conclusions of this presentation conclude that the experiment is feasible with at least 10 critical configurations, and low expected benchmark uncertainty. Potential high impact for the understanding of commercially used neutron absorber plates. Next steps are to think about other configurations: rod pitch, other rods – Finalize plate support, uncertainty study. Additionally, the potential use of IER-441 central test region to safely place the plate in the core. Next steps include the Determination of the neutron absorber plate characterization path and the Potential SINBAD benchmark of neutron transmission measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Electropolishing of a Full-Sized U-10Mo Plate

Electropolishing is used to remove material from the surface of a metal using electric potential and current. U-10Mo fuel is produced from a low enriched uranium plate alloyed with 10% molybdenum (U-10Mo). Electropolishing is being considered in two steps of the process of fabricating this U-10Mo fuel. First, it could be used as a means initially improving the surface finish of the cast plate while removing smut from the casting process from the surface prior to homogenization. Second, it could be used again after homogenization to remove oxidation and continue to improve the surface finish prior to hot rolling. The purpose of this work is to demonstrate the process on full-size ingots and optimize the process. A depleted uranium U-10Mo plate was electropolished three times: the first two times were prior to homogenization and the third after a homogenization step. The first two polishes decreased the overall roughness, as measured by laser confocal microscopy. After each polish, a smoother and shinier blue-gold surface was left on the plate. Upon homogenization, the surface had a more matte appearance and the surface roughness increased back to the pre-homogenization values obtained prior to the initial polish. After electropolishing the homogenized pieces, the changes in surface roughness increased, as measured by laser confocal microscopy. The final polishing step was not long enough to return the surface roughness to pre-homogenization conditions, implying less polishing is needed before the homogenization versus afterwards. Heat generation during the polish was addressed by circulating the electrolyte solution through an external heat exchanger; however, solubility and anodization challenges require further study.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

HEU Pancake Plates

The HEU Pancake plates, formerly known as the Jemima plates, were procured in two batches. The first, consisting of the 15” plates, was ordered and produced by LANL in 1958. A second set, consisting of the 21” rings was ordered by LANL but produced by ORNL sometime in the 1960s. The plates were used at LACEF in experiments such as Big Ten and the Zeus series of experiments. In the mid-2000s, they were shipped to NCERC where they reside today. Since being at NCERC, they have been used in Zeus and TEX style experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Sensitivity calibration of a Carestream HPX-1 image plate scanner

There is a need to measure the sensitivity of the image plate scanners used to scan Z shot data. The Carestream HPX-1 image plate scanner was tested, and its performance was characterized to determine the system sensitivity in terms of signal per incident photon as a function of x-ray energy. A Manson source was used to simultaneously expose an Amptek x-ray multi-channel analyzer and image plates, allowing for a comparison of the counts as a function of energy to the signal recorded on the image plates. NIST-certified radioactive sources were used to assign an absolute sensitivity. Results indicate that the HPX-1 scanner response matches the shape of the modeled response, allowing for absolute scaling using NIST-certified radioisotope sources. The HPX-1 scanner shows a stable response with measurements taken over one week. In contrast, the sensitivity of the DITABIS scanner was characterized using the same approach, but it exhibits changes in its response that varied by more than 50% over the span of 4 days.

42 ENGINEERING↗
DOE OSTI2025

Increasing Radon Daughter Plate-out onto Superconducting Qubits

Radon daughter plate-out may pose a fundamental limitation to realizing large-scale superconducting quantum computers. Radon daughters plated-out onto a superconducting qubit chip can decay, releasing energy into the substrate, producing phonons. Phonon induced quasiparticles generate bit flip errors and reduce coherence times. We seek to increase plate-out on chips to enable future study of the impact of Radon on coherence times. In this project, we utilize COMSOL Multiphysics simulations to finalize design for a device to increase radon plate-out.

Kay, Dax [Northwestern U.]↗
DOE OSTI2015

Parametric Sensitivity Comparison of Simulation Models for Flyer Plate Impact Experiments

This paper compares the sensitivities of different modeling approaches for fundamental flyer plate impact experiments to variations of several input parameters. Two modeling approaches are used to model a copper flyer plate experiment: the CTH hydrodynamic code and the LS-DYNA code using the smoothed particle hydrodynamic (SPH) approach. Simulations using these two methods are compared to experimental data from a gas gun experiment in which a copper flyer plate impacted a copper target plate. The experiment was designed to cause spall in the target. Numerical simulations are conducted using typical input physics models including the Mie-Grüneisen equation of state, the Johnson-Cook compressive strength model, and a pressure cutoff (Pmin) model for tensile damage (spall). Effects of artificial viscosity, spall strength, and computational cell size are studied and discussed with the objective of improving the accuracy of these simulations.

CTH, smoothed particle hydrodynamics, SPH, Johnson↗
DOE OSTI2021

Lead Contamination Differences in the Muscle of Wild Turkeys Harvested with Lead and Copper-Plated Lead Shot

Abstract Despite the known deleterious effects lead exposure can have on humans, lead remains the most common type of ammunition used to harvest big game and upland game birds. We sampled wild turkey Meleagris gallopavo breast muscle shot with standard lead and copper-plated lead pellets to quantify lead residue concentrations within the wound channel, and we sampled multiple adjacent locations to measure the extent lead contamination spreads through tissue of harvested turkeys. We found that samples taken from the wound channel contained more lead (mean = 3.76 μg/g dry weight) than both samples taken adjacent to the wound channel (mean = 0.20 μg/g dry weight) and samples taken from >5 cm away (mean = 0.15 μg/g dry weight). Additionally, we found that birds harvested with standard lead ammunition did not differ in lead concentrations from those shot with copper-plated lead, suggesting that copper plating does not aid in reducing lead exposure. Our findings suggest that wild turkeys harvested with either lead or copper-plated lead shot have the potential to expose consumers, especially children due to their lower tolerance, to low levels of lead that could exceed daily consumption limits set by the Food and Drug Administration and Centers for Disease Control. However, elevated lead levels were confined to the wound channel, and thus proper preparation of game to remove tissue surrounding wound channels may eliminate or substantially reduce lead exposure from harvested game birds.

Biodiversity & Conservation↗
NASA NTRS1971

Automatic plate mensuration and reduction at Aeronautical Chart and Information Center

The use of optical satellite observation data for geodetic purposes depends on the ability to extract pertinent information from photographic plates by identifying points on the plates and correlating them with known star positions for use in geodetic positioning. This procedure is accomplished with a new semi-automatic measuring system, an advanced analytical plate reduction program for the IBM 7094 computer, and a triangulation adjustment. The advantages gained with the measuring system, a brief discussion of the system itself, and the plate reduction and triangulation adjustment are described.

Seppelin, T. O.↗
NASA NTRS1972

Sputtering and ion plating

The proceedings of a conference on sputtering and ion plating are presented. Subjects discussed are: (1) concepts and applications of ion plating, (2) sputtering for deposition of solid film lubricants, (3) commercial ion plating equipment, (4) industrial potential for ion plating and sputtering, and (5) fundamentals of RF and DC sputtering.

Source record↗
NASA NTRS1972

Comparison of aerogrids and punched plates for smoothing flow from short annular diffusers

Scale model tests were conducted to evaluate the effectiveness of aerogrids and punched plates in producing flat velocity profiles downstream of short diffusers as would be used between the compressor and combustor of advanced aircraft engines. The diffuser had an area ratio of 4.17 and a length-to-inlet-height ratio of 2.07. The aerogrids tested were plates containing 1123 contoured venturis in parallel with geometric blockages of 83, 74, and 61 percent, respectively. The punched plates contained 1123 sharp-edged orifices with blockages of 58 and 30 percent. The results show that aerogrids, with higher effective blockage for the same pressure loss, are more effective flow-smoothing devices than the punched plates. Also, the overall pressure loss decreases and the exit velocity profile becomes flatter as either type of grid is moved closer to the diffuser exit plane.

Rumpf, R. L.↗
NASA NTRS1971

Calibration of a laboratory spectrophotometer for specular light by means of stacked glass plates.

Stacked glass plates have been used to calibrate a laboratory spectrophotometer, over the spectral range 0.5-2.5 microns, for specular light. The uncalibrated instrument was characterized by systematic errors when used to measure the reflectance and transmittance of stacked glass plates. Calibration included first, a determination of the reflectance of a standard composed of barium sulfate paint deposited on an aluminum plate; second, the approximation of the reflectance and transmittance residuals between observed and computed values by means of cubic equations; and, finally, the removal of the systematic errors by a computer. The instrument, after calibration, was accurate to 1% when used to measure the reflectance and transmittance of stacked glass plates.

Allen, W. A.↗
NASA NTRS1972

Vibrations of circular elastic plates due to sonic boom.

The problem of transient axisymmetric vibrations of thin circular elastic plates due to sonic boom excitation is investigated. The equation of motion for a solid circular plate is solved by applying the modified finite Hankel transform and the Laplace transform, and the numerical results are obtained with the help of the digital computer. From the analysis of the data, obtained for the dynamic deflections of the plates for the boom duration, it is concluded that for a normal flight the boom duration has a significant effect on the vibrations of plates as compared to the overpressure of the boom.

Pavagadhi, L. J.↗
NASA NTRS1973

Theoretical analysis of impact in composite plates

The calculated stresses and displacements induced anisotropic plates by short duration impact forces are presented. The theoretical model attempts to model the response of fiber composite turbine fan blades to impact by foreign objects such as stones and hailstones. In this model the determination of the impact force uses the Hertz impact theory. The plate response treats the laminated blade as an equivalent anisotropic material using a form of Mindlin's theory for crystal plates. The analysis makes use of a computational tool called the fast Fourier transform. Results are presented in the form of stress contour plots in the plane of the plate for various times after impact. Examination of the maximum stresses due to impact versus ply layup angle reveals that the + or - 15 deg layup angle gives lower flexural stresses than 0 deg, + or - 30 deg and + or - 45 deg. cases.

Moon, F. C.↗